5-225532-8

Instruction Sheet 408-2322 SMA Series 50-Ohm Connectors for Flexible Cable SMA Plug SMA Bulkhead Jack PLUG RG/U Cable 58A, 58C 142, 142A, 142B 174, 188A,316 20 MAY 09 BULKHEAD JACK SMA Right-Angle Plug RIGHT-ANGLE PLUG Crimping Tool Govt Desig M39012/ TE Part No. Govt Desig M39012/ TE Part No. Govt Desig M39012/ TE Part No.. Braid Crimp 55B3021 225532-1 -- -- 56B3021 225609-1 A 55B3022 225532-3 -- -- -- 225609-3 A 55B3019 225532-4 -- 225608-4 56B3019 225609-4 B 180B, 195A -- -- -- -- -- -- A 179B, 187A -- 225532-8 -- -- -- -- B 141, 141A, 303 55B3024 225532-9 -- -- -- -- A 55A, 223 55B3023 1-225532-0 -- -- -- -- A -- 1-225532-1 -- -- -- -- A -- 1-225532-4 -- -- -- -- A 188, 316, Double Braid 142, 142A, 142B Rev A TE Part No. 220061-1 (408 2392) (408-2392) 59962-1 (408-6750) 220061-1 (408-2392) 179B, 187A -- 5-225532-8 -- -- -- -- B Figure 1 1. INTRODUCTION NOTE Examine the braid wires and center conductor of the cable under 10 X magnification for nicks or This instruction sheet deals with SMA Series 50–Ohm Connectors for flexible cable listed in Figure 1. Reasons for re–issue can be found in Section 3, REVISION SUMMARY. NOTE i damage. Be sure that the center conductor is straight and free of burrs. 2. Crimp the center contact onto the center conductor using the tool listed in Figure 1. Dimensions on this sheet are in millimeters [with inch equivalents provided in brackets]. Figures i and illustrations are for identification only and are not drawn to scale. 2. ASSEMBLY PROCEDURE Select the appropriate cable size and connector. Refer to the table in Figure 1. 1. Slide the ferrule onto the cable, then strip the cable according to the dimensions shown in Figure 2. E 2009 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved Figure 2 3. Insert the crimped contact into the connector with the braid over the support sleeve. Pull back lightly on the cable to ensure that the contact is TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 2 LOC B 408-2322 SMA Series 50-Ohm Connectors for Flexible Cable held captive by the contact’s internal locking features. Refer to Figure 3. Support Sleeve Cable of Connector Braid Ferrule 3. REVISION SUMMARY Since the previous release of this instruction sheet, the follow changes have been made: S Steps have been added to the assembly procedure; S The TE logo has been applied; and S Added three SMA Plugs; S The format has been updated to the current corporate requirements,. Crimped Contact Figure 3 NOTE Due to the size and smoothness of certain cables (RG 316 188A), wrapping masking tape i temporarily around the cable jacket will aid in gripping the cable jacket while pushing the contact in to engage the internal locking feature. Also grip the cables close to the connector to prevent the cable from buckling. NOTE If the cable jacket moves on short lengths of cable (such as RG 316 an 188A), trim the end of i the jacket as shown in Figure 4. If the Cable Has Moved on the Braid During Contact Insertion, Trim the End of the Jacket as Shown. 7.137 [.0281] Braid Over Connector Support Sleeve Slide the Ferrule Forward Over the Braid and Support Sleeve Figure 4 4. Slide the ferrule over the braid as shown in Figure 4. 5. Crimp the ferrule onto the braid using the tool listed in Figure 1. 6. Examine the crimps under magnification for damage or irregularities. Periodically inspect the die closure of the hand tool (see 408–2392) 7. Torque the mated connectors seven to ten inch pounds. 2 of 2 Tyco Electronics Corporation Rev A