55/1812-22-9-9

SCD SPECIFICATION CONTROL DRAWING Title 55/1812 Date ONE CONDUCTOR CABLE, SHIELDED, JACKETED, 6-30-16 OUTER SPACE, 600 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 55/. COMPONENT WIRE - 55/0812 SHIELD - SILVER-COATED COPPER Revision C JACKET - LOW OUTGASSING, RADIATION-CROSSLINKED, MODIFIED ETFE CABLE CONSTRUCTION DETAILS JACKET THICKNESS (inch) OUTSIDE DIAMETER (inch) PART NUMBER 1/ CONDUCTOR SIZE (AWG) SHIELD SIZE (AWG) MINIMUM NOMINAL NOMINAL MAXIMUM 55/1812-28-* 28 38 .006 .008 .068 .074 4.7 55/1812-26-* 26 38 .006 .008 .073 .079 5.6 55/1812-24-* 24 38 .006 .008 .078 .084 6.6 55/1812-22-* 22 38 .006 .008 .083 .089 7.8 55/1812-20-* 20 38 .006 .008 .091 .098 9.9 55/1812-18-* 18 38 .006 .008 .103 .111 13.3 55/1812-16-* 16 38 .006 .008 .110 .118 15.6 55/1812-14-* 14 38 .006 .008 .127 .135 21.7 55/1812-12-* 12 38 .006 .008 .144 .152 29.6 55/1812-10-* 10 38 .006 .008 .167 .180 43.2 55/1812-8-* 8 38 .007 .009 .230 .249 77.8 MAXIMUM WEIGHT (lbs/1000 ft.) CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 200°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level CROSSLINKED VERIFICATION: 300 ± 3°C for 1 hour DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz JACKET COLOR: White preferred JACKET ELONGATION: 50% (minimum) JACKET FLAWS: Spark Test, 1000 volts (rms) Impulse Dielectric Test, 6.0 kV (peak) RADIATION RESISTANCE: 500 megarads SHIELD COVERAGE: 85% (minimum) VACUUM STABILTY: Total Mass Loss (TML), 1.00% (maximum) Volatile Condensable Material (VCM), 0.10% (maximum) VOLTAGE WITHSTAND (Post Environmental): 1500 volts (rms), 60 Hz, 1 minute 1/ PART NUMBER: The "*" in the part numbers above shall be replaced by color code designators with a dash separating the component wire color from the jacket color. Example: AWG 22, white component wire; white jacket: 55/1812-22-9-9 NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Page 1 of 1 DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2016 Tyco Electronics Corporation. All rights reserved.