55A0114-26-4

SPECIFICATION CONTROL DRAWING Title SCD 55A0114 Date WIRE, RADIATION-CROSSLINKED, MODIFIED, ETFE-INSULATED, SILVER-COATED HIGH STRENGTH COPPER ALLOY, LIGHTWEIGHT Revision 2-7-22 R This specification sheet forms a part of the latest issue of Raychem Specification 55A. CONDUCTOR - SILVER-COATED HIGH-STRENGTH COPPER ALLOY INSULATION - RADIATION-CROSSLINKED, MODIFIED ETFE TABLE I. CONSTRUCTION DETAILS CONDUCTOR STRANDING (number x AWG) DIAMETER OF STRANDED CONDUCTOR (inch) FINISHED WIRE PART NUMBER 1/ WIRE SIZE (AWG) MINIMUM MAXIMUM 55A0114-30-* 30 7 x 38 .011 .012 117.4 .024 ± .002 .66 55A0114-28-* 28 7 x 36 .014 .016 74.4 .027 ± .002 .91 MAXIMUM RESISTANCE AT 20°C (ohms/1000 ft.) DIAMETER (inch) MAXIMUM WEIGHT (lbs/1000 ft.) 55A0114-26-* 26 19 x 38 .018 .020 44.8 .032 ± .002 1.4 55A0114-24-* 24 19 x 36 .023 .025 28.4 .037 ± .002 2.0 55A0114-22-* 22 19 x 34 .029 .031 17.5 .043 ± .002 2.9 55A0114-20-* 20 19 x 32 .037 .039 10.7 .050 ± .002 4.4 55A0114-18-* 18 19 x 30 .046 .050 6.8 .060 ± .002 6.5 55A0114-16-* 16 19 x 29 .052 .057 5.3 .068 ± .002 8.3 TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER 1/ MANDREL DIAMETER (inch) (± 3%) WEIGHT (lb) (± 3%) IMMERSION, LIFE CYCLE, AND ACCELERATED AGING COLD BEND IMMERSION, LIFE CYCLE, AND ACCELERATED AGING COLD BEND 55A0114-30-* .250 .375 .125 .500 55A0114-28-* .250 .375 .125 .500 55A0114-26-* .375 .500 .125 .500 55A0114-24-* .375 .500 .250 1.00 55A0114-22-* .500 .750 .375 1.00 55A0114-20-* .500 .750 .500 1.00 55A0114-18-* .500 1.00 .500 1.00 55A0114-16-* .750 1.00 .750 1.00 Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. TE Connectivity Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE Connectivity (logo), and TE (logo) are trademarks. Page 1 of 2 DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-522-6752 © 2015-2022 TE Connectivity Corporation. All rights reserved. Page SPECIFICATION CONTROL DRAWING 2 of 2 Revision SCD R 55A0114 WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 200°C, Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level ACCELERATED AGING (CROSSLINKING PROOF): 300 ± 3°Cfor 7 hours BLOCKING: 230 ± 3°C for 24 hours COLOR: white preferred CONCENTRICITY: 70% (minimum) FLAMMABILITY: Procedure 1, 3 seconds (maximum); 3 in. (maximum); no flaming of facial tissue. HUMIDITY RESISTANCE: Insulation Resistance, 5000 megohms for 1000 ft. (minimum) IDENTIFICATION, COLOR STRIPING AND BAND DURABILITY: 125 cycles (250 strokes) (minimum), 500 g weight IMMERSION: Diameter increase 5% (maximum); no cracking, no dielectric breakdown INSULATION ELONGATION AND TENSILE STRENGTH: Elongation, 75% (minimum) Tensile strength, 5000 lbf/in2 (minimum) INSULATION FLAWS: Spark Test, 5.7 kV (rms) at 3 kHz Impulse DielectricTest, 8.0 kV (peak); INSULATION RESISTANCE: 5000 megohms for 1000ft (minimum) INSULATION THICKNESS: 0.005 in. (minimum) LIFE CYCLE: 230 ± 3°C for 500 hours LOW TEMPERATURE-COLD BEND: -65 ± 3°C for4 hours SHRINKAGE: 230 ± 3°C, for 6 hours, 0.125 in. (maximum) in 12 in. SOLDERABILITY: Per MIL-STD-202, Method 208, without steam aging SMOKE TEST: 250 ± 5°C. No visible smoke SURFACE RESISTANCE: 500 Megohms-in. (minimum), both readings THERMAL SHOCK RESISTANCE: 200 ± 3°C, 0.060 in. (maximum) VOLTAGE WITHSTAND TEST (Post Environmental): 2500 volts (rms), 60 Hz WRAP TEST: 313 ± 3°C for 2 hours 1/PART NUMBER: The"*" in the part numbers on page 1 shall be replaced by a color code designator. Example: AWG 22, white: 55A0114-22-9 AWG 22, white with black stripe: 55A0114-22-90 (Note: Striping/marking is not available for AWG 28 and 30.) 1/ See footer section on page 1