55A1112-24-9-9CS2275

TITLE SPECIFICATION CONTROL DRAWING Date ONE CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT 55A1112 6-25-13 Revision F This specification sheet forms a part of the latest issue of Raychem Specification 55A. JACKET - RADIATION-CROSSLINKED, MODIFIED ETFE SHIELD - SILVER-COATED COPPER COMPONENT WIRE - 55A0112 CABLE CONSTRUCTION DETAILS JACKET THICKNESS (inches) OUTSIDE DIAMETER (inches) PART NUMBER 1/ CONDUCTOR SIZE (AWG) SHIELD SIZE (AWG) MINIMUM NOMINAL NOMINAL MAXIMUM MAXIMUM WEIGHT (lbs/1000 ft.) 55A1112-30-* 30 38 .006 .008 .057 .062 3.4 55A1112-28-* 28 38 .006 .008 .060 .065 3.9 55A1112-26-* 26 38 .006 .008 .065 .070 4.7 55A1112-24-* 24 38 .006 .008 .070 .076 5.7 55A1112-22-* 22 38 .006 .008 .076 .082 6.9 55A1112-20-* 20 38 .006 .008 .083 .089 8.9 55A1112-18-* 18 38 .006 .008 .093 .100 11.9 55A1112-16-* 16 38 .006 .008 .101 .108 14.3 55A1112-14-* 14 38 .006 .008 .118 .126 20.2 55A1112-12-* 12 38 .006 .008 .136 .144 28.2 55A1112-10-* 10 38 .006 .008 .161 .175 42.7 55A1112- 8-* 8 38 .007 .009 .223 .243 75.9 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 200°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level ACCELERATED AGING: 300 ± 3°C for 7 hours BLOCKING: 200 ± 3°C for 6 hours DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz FLAMMABILITY (Procedure 1): 3 seconds (maximum); 3 in. (maximum); no flaming of facial tissue JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 50% (minimum) Tensile Strength, 5000 lbf/in² (minimum) JACKET FLAWS: Spark Test, 1000 volts (rms) Impulse Dielectric Test, 6.0 kV (peak) LIFE CYCLE: 230 ± 3°C for 500 hours LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute PART NUMBER: The “*” in the part numbers above shall be replaced by color code designators with a dash separating the component wire color from the jacket color. 1/ Example: AWG 20, black component wire; white jacket: 55A1112-20-0-9 NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 1 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2008-2013 Tyco Electronics Corporation. All rights reserved.