55A6213-24-9-9CS2275

TITLE SPECIFICATION CONTROL DRAWING Date ONE CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT 55A6213 11-19-12 Revision B This specification sheet forms a part of the latest issue of Raychem Specification 55A. COMPONENT WIRE- 55A0813 JACKET - RADIATION-CROSSLINKED, MODIFIED ETFE SHIELD - TIN-COATED COPPER CABLE CONSTRUCTION DETAILS JACKET THICKNESS (inches) OUTSIDE DIAMETER (inches) PART NUMBER 1/ CONDUCTOR SIZE (AWG) SHIELD SIZE (AWG) MINIMUM MAXIMUM NOMINAL MAXIMUM MAXIMUM WEIGHT (lbs/1000 ft.) 55A6213-24-* 24 38 .005 .010 .078 .084 6.6 55A6213-22-* 22 38 .005 .010 .083 .089 7.8 55A6213-20-* 20 38 .005 .010 .091 .098 9.9 55A6213-18-* 18 38 .005 .010 .103 .111 13.3 55A6213-16-* 16 38 .005 .010 .110 .118 15.6 55A6213-14-* 14 38 .005 .010 .127 .135 21.7 55A6213-12-* 12 38 .005 .010 .144 .152 29.6 55A6213-10-* 10 38 .006 .011 .167 .180 43.2 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level BLOCKING: 200 ± 3°C for 6 hours CROSSLINKED VERIFICATION: 300 ± 5°C for 6 hours DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz FLAMMABILITY (Procedure 1): 3 seconds (maximum); 3 in. (maximum); no flaming of facial tissue JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 50% (minimum) Tensile Strength, 5000 lbf/in² (minimum) JACKET FLAWS: Spark Test, 1.5 kV (rms) Impulse Dielectric Test, 6.0 kV (peak) LOW TEMPERATURE-COLD BEND: -55 ± 5°C for 4 hours SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute PART NUMBER: The “*” in the part numbers above shall be replaced by color code designators with a dash separating the component wire color from the jacket color. 1/ Example: AWG 20, white component wire; white jacket: 55A6213-20-9-9 NOTE: Nominal values are for information only. Nominal values are not requirements. This cable shall meet all constructional requirements of M27500 (AWGSM1T23). Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 1 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2012 Tyco Electronics Corporation. All rights reserved.