55FA/0514-24-7L

SPECIFICATION CONTROL DRAWING 55FA/0514 TITLE Date CABLE, ELECTRIC, FILTER LINE - ELECTROLOSS, OUTER SPACE, COMPONENT WIRE Revision 9-30-13 B This specification sheet forms a part of the latest issue of Raychem Specification 55F. FILTER LAYER - RADIATION-MODIFIED, ABSORPTIVE COMPOUND CONDUCTOR - SILVER-COATED HIGH-STRENGTH COPPER ALLOY PRIMARY JACKET - LOW OUTGASSING, RADIATION-CROSSLINKED, MODIFIED ETFE PRIMARY INSULATION - RADIATION-CROSSLINKED, MODIFIED PVDF COLOR - NATURAL TABLE I. CONSTRUCTION DETAILS PART NUMBER 1/ WIRE SIZE (AWG) CONDUCTOR STRANDING (number x AWG) DIAMETER OF STRANDED CONDUCTOR (in.) FINISHED WIRE MINIMUM MAXIMUM MAXIMUM RESISTANCE AT 20°C (ohms/1000 ft) DIAMETER (in.) MAXIMUM WEIGHT (lbs/1000 ft.) 55FA/0514-26-* 26 19 x 38 .018 .020 44.8 .043 ± .002 2.3 55FA/0514-24-* 24 19 x 36 .023 .025 28.4 .045 ± .002 3.0 55FA/0514-22-* 22 19 x 34 .029 .032 17.5 .051 ± .003 4.0 55FA/0514-20-* 20 19 x 32 .037 .040 10.7 .059 ± .003 5.8 TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER 1/ MANDREL DIAMETER (inch) (± 3%) WEIGHT (lb) (± 3%) IMMERSION, LIFE CYCLE, AND CROSSLINKING PROOF TEST COLD BEND IMMERSION, LIFE CYCLE, AND CROSSLINKING PROOF TEST COLD BEND 55FA/0514-26-* .500 1.00 .500 3.00 55FA/0514-24-* .500 2.00 .625 3.00 55FA/0514-22-* .500 2.00 .750 3.00 55FA/0514-20-* .750 2.50 1.25 4.00 Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 3 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2013 Tyco Electronics Corporation,. All rights reserved. Revision SPECIFICATION CONTROL DRAWING Page 2 of 3 B SCD Number 55FA/0514 WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level ATTENUATION (INSERTION LOSS): See Table III BLOCKING: 200 ± 3°C for 6 hours COLOR: Light violet preferred CONCENTRICITY: Primary Insulation - 50% (minimum); Finished Wire - 70% (minimum) CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours FLAMMABILITY: 3 seconds (maximum); 3 inches (maximum); no flaming of facial tissue HUMIDITY RESISTANCE: Insulation Resistance, 5000 megohms for 1000 ft. (minimum) IDENTIFICATION AND COLOR STRIPING DURABILITY: 125 cycles (250 strokes) (minimum), 500 g weight IMMERSION: Diameter increase 5% (maximum); no cracking, no dielectric breakdown INSULATION ELONGATION AND TENSILE STRENGTH: Primary Insulation, Filter Layer, and Primary Jacket pulled together Elongation, 50% (minimum) Tensile Strength, 3000 lbf/in2 (minimum) INSULATION FLAWS: Primary Insulation only, Spark Test, 1.5 kV (rms) at 60 Hz 4.2 kV (rms) at 3 KHz Impulse Dielectric Test, 6.0 kV (peak) Finished Wire, Spark Test, 3.0 kV (rms) at 60 Hz 5.7 kV (rms) at 3 kHz Impulse Dielectric Test, 8.0 kV (peak) INSULATION RESISTANCE: 5000 megohms for 1000 ft. (minimum) INSULATION THICKNESS: Primary Insulation, .002 in. (minimum); Filter Layer, average, .0025 in. (minimum); Primary Jacket, .0035 in. (minimum) LIFE CYCLE: 200 ± 3°C for 168 hours LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours SHRINKAGE: 200 ± 3°C for 6 hours, 0.125 inches (maximum) SMOKE: 200 ± 2°C, no visible smoke SURFACE RESISTANCE: 500 megohms-in. (minimum), initial and final readings THERMAL-SHOCK RESISTANCE: 150 ± 3°C, 0.060 inch (maximum) THERMAL STABILITY: 180 ± 3°C for 1250 hours VACUUM STABILITY: Total Mass Loss (TML), 1.00% (maximum) Volatile Condensable Material (VCM), 0.10% (maximum) VOLTAGE WITHSTAND (Post Environmental): 1500 volts (rms), 60 Hz WRAP TEST: 200 ± 3°C for 6 hours, no cracking 1/ PART NUMBER: The "*" in the part numbers in Tables I-III shall be replaced by a color code designator, except that violet shall be light violet and designator shall be 7L. Example: AWG 24, light violet: 55FA/0514-24-7L AWG 24, light violet with a blue stripe: 55FA/0514-24-7L6 1/ See footer section on page 1 Revision SPECIFICATION CONTROL DRAWING Page 3 of 3 SCD Number 55FA/0514 B 100 90 80 70 60 Attenuation (dB/foot) 50 Typical curve for size 24 40 30 20 10 0 1.0 10.0 100. 1000. Frequency (MHz) ATTENUATION (INSERTION LOSS) TABLE III. ATTENUATION (INSERTION LOSS) + PART NUMBER 1/ PASS BAND (dB/ft.) 1.0 MHz TRANSITION BAND (dB/ft.) 10.0 MHz STOP BAND (dB/ft.) 100 MHz 500 MHz 1000 MHz 1 to 12 GHz (max) (min) (max) (min) (min) (min) (min) 55FA/0514-26-* TBD TBD TBD TBD TBD TBD TBD 55FA/0514-24-* .02 .06 0.20 1.3 12 30 30 55FA/0514-22-* .02 .06 0.20 1.3 12 30 30 55FA/0514-20-* .02 .06 0.20 1.3 12 30 30 1/ See footer section on page 1 + THE PRIMARY WIRE OF THIS SPECIFICATION SHEET SHALL MEET THE ATTENUATION REQUIREMENTS SHOWN ABOVE ONLY WHEN USED AS A SINGLE COMPONENT IN A SHIELDED CABLE.