55PC1211-20-9-2CS2502

SCD SPECIFICATION CONTROL DRAWING Title 55PC1211 Date ONE CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT Revision 10-6-15 D This specification sheet forms a part of the latest issue of Raychem Specification 55PC. COMPONENT WIRE - 55PC0211 SHIELD - TIN-COATED COPPER JACKET - RADIATION-CROSSLINKED, MODIFIED ETFE CABLE CONSTRUCTION DETAILS PART NUMBER 1/ CONDUCTOR SIZE (AWG) SHIELD SIZE (AWG) 55PC1211-26-* 26 55PC1211-24-* 24 55PC1211-22-* JACKET THICKNESS (inch) OUTSIDE DIAMETER (inch) WEIGHT (lbs/1000 ft.) LOWER SPEC LIMIT TARGET WALL LOWER SPEC LIMIT TARGET VALUE UPPER SPEC LIMIT TARGET VALUE UPPER SPEC LIMIT 38 .0050 .0060 .060 .064 .068 4.40 4.68 38 .0050 .0060 .065 .069 .073 5.28 5.57 22 38 .0050 .0060 .071 .075 .079 6.59 6.89 55PC1211-20-* 20 38 .0050 .0060 .080 .083 .087 8.62 8.96 55PC1211-18-* 18 38 .0050 .0060 .089 .093 .097 11.43 11.84 55PC1211-16-* 16 38 .0050 .0060 .097 .100 .104 13.68 14.11 55PC1211-14-* 14 38 .0050 .0065 .112 .116 .120 19.28 19.85 55PC1211-12-* 12 38 .0050 .0065 .131 .135 .140 27.37 28.05 55PC1211-10-* 10 38 .0050 .0065 .154 .159 .164 40.25 41.30 55PC1211-8-* 8 38 .0070 .0090 .219 .231 .243 73.26 75.89 Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Page 1 of 2 DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2015 Tyco Electronics Corporation. All rights reserved. Page SPECIFICATION CONTROL DRAWING 2 of 2 Revision SCD D CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level CROSSLINKED VERIFICATION: 300 ± 3°C for 1 hour DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 50% (minimum) Tensile Strength, 5000 lbf/in2 (minimum) JACKET FLAWS: Spark Test, 1000 volts (rms) Impulse Dielectric Test, 6.0 kV (peak) SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute 1/ PART NUMBER: The "*" in the part numbers on page 1 shall be replaced by color code designators with a dash separating the component wire color from the jacket color. Example: AWG 22, white component wire; white jacket: 55PC1211-22-9-9 1/ See footer section on page 1 55PC1211