55PC6309-10-9-9-9CS2970

TITLE SPECIFICATION CONTROL DRAWING Date ONE CONDUCTOR CABLE, DOUBLE SHIELDED, DOUBLE JACKETED, GENERAL PURPOSE, 600 VOLT 55PC6309 2-13-13 Revision B This specification sheet forms a part of the latest issue of Raychem Specification 55PC. COMPONENT WIRE - 55PC0213 JACKETS - RADIATION-CROSSLINKED, MODIFIED ETFE SHIELDS - NICKEL-COATED COPPER CABLE CONSTRUCTION DETAILS 1st JACKET THICKNESS ( in. ) LOWER SPEC LIMIT TARGET WALL 2nd SHIELD SIZE (AWG) 38 .0050 .0060 38 .0050 .0060 18 38 .0050 55PC6309-16-* 16 38 55PC6309-14-* 14 38 55PC6309-12-* 12 55PC6309-10-* 10 PART NUMBER 1/ CONDUCTOR SIZE (AWG) 1st SHIELD SIZE (AWG) 55PC6309-22-* 22 55PC6309-20-* 20 55PC6309-18-* 2nd JACKET THICKNESS ( in. ) OUTSIDE DIAMETER ( in. ) LOWER SPEC LIMIT TARGET WALL LOWER SPEC LIMIT TARGET VALUE 38 .0050 .0060 .098 .104 38 .0050 .0065 .105 .113 .0060 38 .0050 .0065 .116 .123 .0050 .0060 38 .0050 .0065 .121 .0050 .0065 38 .0050 .0065 .137 38 .0050 .0065 38 .0055 .0070 38 .0050 .0065 38 .0055 .0070 UPPER SPEC LIMIT WEIGHT ( lbs/1000 ft. ) TARGET VALUE UPPER SPEC LIMIT .110 11.87 12.83 .121 14.48 15.59 .130 17.96 19.28 .130 .139 20.62 22.04 .146 .155 27.22 28.96 .156 .166 .176 36.68 38.79 .176 .190 .204 51.16 53.97 Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 2 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2013 Tyco Electronics Corporation,. All rights reserved. Revision SPECIFICATION CONTROL DRAWING Page 2 of 2 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 200°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level CROSSLINK VERIFICATION: 300 ± 3°C for 1 hour DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz conductor to shield 500 volts (rms), 60 Hz shield to shield JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 50% (minimum) (each) Tensile Strength, 5000 lbf/in² (minimum) (each) JACKET FLAWS: Spark Test, 1000 volts (rms) Impulse Dielectric Test, 6.0 kV (peak) SHIELD COVERAGE: 85% (minimum) (each) VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute PART NUMBER: The "*" in the part numbers on page 1 shall be replaced by color code designators with a dash separating the component wire color from the inner jacket color and a dash separating the inner jacket color from the outer jacket color. 1/ Example: AWG 22, white component wire; white inner jacket and white outer jacket: 55PC6309-22-9-9-9 1/ See footer section on page 1 B SCD 55PC6309