601164-000

Coaxial Cable Termination SolderSleeve PCB/Coaxial Cable Terminators Product Facts Provides a completely shielded, low-resistance, matched-impedance termination with very low VSWR (D-607 series only) ■ Transparent polyvinylidene fluoride insulation sleeve provides encapsulation, inspectability, strain relief, and insulation ■ Prefluxed solder preform provides a controlled soldering process ■ One-piece design offers easy installation and lower installed cost ■ Preinstalled PCB termination body provides convenience and ease of installation ■ Applications Installation Product Selection Process Used for terminating coaxial cable to printed circuit boards. For proper installation of these devices, the correct heating tool and reflector attachment must be used. Any one of the following TE heating tools is recommended: 1. Select product series from the Product Options table below. ■ HL1910E/HL2010E ■ AA-400 Super Heater ■ IR-1759 MiniRay ■ CV-1981 2. Determine cable RG number or outside diameter dimensions. 3. Select the appropriate part number from Table A (D-607 series) or Table B (B-046 series). For D-607 (matched impedance) series, determine straight or rightangle entry to PCB and grid pattern, then select the appropriate part number from Table A on the next page. ■ For B-046 (PinPak, or pin to ground) series, determine hole spacing and diameter. Refer to Table B for product selection (see illustration below for cable dimensions). Refer to TE installation procedure ES-61139 for detailed instructions and recommended reflector attachments. You will find ordering information for these tools in Section 10. Available in: Americas Europe Asia Pacific A B C D 8 Electrical Interconnect Products ■ ■ ■ ■ Product Options Product Series D-607 B-046 Typical Application Performance Matched impedance up to 2.3 GHz Effective transmission up to 100 MHz Shield Method Metal body Pin to ground Part No. Selection Table A B 8-57 Catalog 1654025 Revised 5-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 Coaxial Cable Termination SolderSleeve PCB/Coaxial Cable Terminators (Continued) Specifications/Approvals TE RT-1404 RT-1404 Series D-607 B-046 Table A. D-607 Series Part Numbers Cable Dimensions (mm/in) Max. Outside Diameter Jacket Shield Dielectric Straight grid 5.08 [.200] Part No. Entry to PCB Right-Angle Grid 5.08 [.200] 1.5–3.55 [.060–.140] 1.1–3.15 [.045–.125] 0.60–2.25 [.025–.090] D-607-09 D-607-10 RG Cable No. 174, 178, 179, 316, 404 Straight Grid 2.54 [.100] D-607-40* Table B. B-046 Series Part Numbers Cable Dimensions RG Cable No. Part No. A B C D Max. Pin Diameter Spacing Between Pins 2.54 [.100] 178, 404 0.30–0.80 [.011–.032] 0.5–1.7 [.019–.067] 1.3–2.3 [.050–.091] 3.4 [.134] 0.6 [.023] 0.8 [.031] B-046-14-N 179, 316 0.3–1.6 [.011–.063] 1.2–2.5 [.047–.100] .1.5–2.8 [.060–.110] 4.4 [.173] 0.6 [.023] 0.8 [.031] B-046-15-N 5.08 [.200] 6.35 [.250] B-046-10-N B-046-11-N B-046-66-N B-046-68-N B-046-12-N B-046-13-N B-046-16-N B-046-18-N Product Characteristics Material Insulation Solder and flux Termination body/pin Radiation-crosslinked, heat-shrinkable polyvinylidene fluoride Solder: Sn63 Pb37 Flux: ROL1 per ANSI - J - 004 (RMA flux) Copper alloy, solder-plated Typical Performance Voltage drop Tensile strength Dielectric strength Temperature rating Insulation resistance 2.0 mV Exceeds strength of conductor 2.0 kV -55°C to 150°C [-67°F to 302°F] 1000 megohms Electrical Performance (typical) D-607 Series Only Frequency 350 MHz 700 MHz 2.3 GHz VSWR (D-607-09, -40) 1.04 max. 1.05 max. 1.09 max. VSWR (D-607-10) 1.04 max. 1.09 max. 1.12 max. 8-58 Catalog 1654025 Revised 5-12 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico/C. Am.: +52 (0) 55-1106-0800 Latin/S. Am.: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015