6116689-3

7 8 C 6 5 4 3 2 1 REVISIONS 2021 TE Connectivity. All Rights Reserved. P LTR DESCRIPTION DATE DWN APVD A1 REVISED PER ECO-09-025699 12DEC09 KK AEG B REVISED PER ECO-21-000623 28JAN2021 AK SZ 1.223 [31.06 ] .048 [1.22 ] 4.655 [118.24 ] PANEL SHOWN IN THIS VIEW FOR CLARITY 1 .724 [18.39 ] D SEE DETAIL HOUSING: PBT POLYESTER, BLACK, UL 94V-O. TERMINALS: 0.30 THICK PHOS BRONZE PLATED WITH 1.27µm MINIMUM THICK HARD GOLD IN LOCALIZED AREA AND 2µm MINIMUM THICK MATTE TIN IN ACTION PIN COMPLIANT PIN TERMINAL AREA OVER 1.27µm MINIMUM THICK NICKEL UNDERPLATE. SHIELD: 0.25 THICK COPPER ALLOY PLATED WITH 1.27µm MINIMUM NICKEL. GROUND CLIPS: 0.25 THICK COPPER ALLOY PLATED WITH 2.03µm MINIMUM MATTE TIN OVER 1.27µm MINIMUM NICKEL. PC BOARD REF .905 [22.99 ] A .017 [0.43 ] .225 [5.71 ] ORGANIZER PC BOARD REF .070 .024 [1.78 0.61 ] RECOMMENDED PANEL LOCATION 2. JACK CAVITY CONFORMS TO FCC RULES AND REGULATIONS, PART 68 SUBPART F. 3. ALL DIMENSIONS ARE NOMINAL UNLESS OTHERWISE SPECIFIED. D 4 DRILLED HOLE DIA = .040 # .001. COPPER THICKNESS = .001-.003. TIN THICKNESS = .0003 MIN. 5 DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 6 THESE FOUR SIDE PCB ACTION PIN GROUNDS AND CORRESPONDING PCB HOLES ARE REQUIRED ONLY ON 6116689-3. 7 DATE CODE LOCATED ON REAR OF PART APPROXIMATELY AS SHOWN. 8 OBSOLETE PARTS: OBSOLETE CIS STREAMLINING PER D.RENAUD/D.SINISI. P/N 6116689-1 SHOWN 7 C C D/C 0015 .575 [14.6 ] TYP .095 REF [2.42 ] PARTIAL BACK VIEW P/N 6116689-1 SCALE B 4:1 B 6 SHIELD WITH 4 PCB ACTION PIN GROUNDS, 2 PER SIDE CONTACTS ARE NOT INTENDED TO BE ALIGNED WITH EACH OTHER DETAIL A SCALE 15:1 TYPICAL OBSOLETE 8 8 GROUND CLIP QUANTITY 8 P/N 6116689-4 SCALE 4805 (3/13) 4:1 DIMENSIONS: GROUND CLIP QUANTITY 8 P/N 6116689-3 SCALE 4:1 INCHES [mm] MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.25 [.010] - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - - 6116689-4 4 6116689-3 NONE NONE 6116689-1 GROUND CLIPS SIDE PCB ACTION PIN GNDS PART NUMBER 8 A THIS DRAWING IS A CONTROLLED DOCUMENT. NONE 23JUN2005 L. VARELA - DOCK5 CHK 23JUN2005 J. WESTMAN APVD 23JUN2005 S. FLICKINGER 6 DWN PRODUCT SPEC 108-1854 APPLICATION SPEC 114-2160 WEIGHT - CUSTOMER DRAWING A TE Connectivity NAME STACKED MODULAR JACK ASSEMBLY, 2 X 8, 8 POSITION, SHIELDED, PANEL GROUND, OFFSET, CAT 5 SIZE CAGE CODE A1 00779 DRAWING NO RESTRICTED TO 6116689 SCALE 3:1 SHEET 1 OF 2 REV B 7 8 C 6 5 4 3 2 1 REVISIONS 2021 TE Connectivity. All Rights Reserved. P LTR - DESCRIPTION DATE SEE SHEET 1 DWN - - APVD - 4.690 [119.13 ] D D PC BOARD REF .940 [23.88 ] .243 REF [6.18 ] TOP OF PC BOARD RECOMMENDED PANEL CUT-OUT C C 5 6 4.025 [102.24 ] XXX .110 [2.8 ] 3.263 [82.87 ] 2.875 [73.03 ] 5 2.300 [58.42 ] -X- 1.150 [29.21 ] .035 .002 [0.89 0.06 ] B .210 [5.33 ] 2 PLC 6 .080 [2.03 ] TYP .575 [14.6 ] PLATED THROUGH HOLES TYP 6 .035 .002 [0.89 0.06 ] 1.725 [43.82 ] 4 .210 [5.34 ] 3 2 PLC .150 [3.81 ] 2 PLC .039 [1] 4 .040 [1.02 ] TYP .575 [14.61 ] TYP 7 PLC B .1875 [4.7625 ] TYP .044 [1.13 ] .064 [1.62 ] TYP DETAIL B THESE PLATED PADS REQUIRED FOR 6116689-3 & -4 PRODUCTS WITH GROUNDING CLIPS SCALE 10:1 8 PLACES 1 8 8 .100 [2.54 ] TYP 1 .160 [4.06 ] TYP 5 -Y- .625 [15.88] WITH GROUNDING CLIPS .635 [16.13 ] WITHOUT GROUNDING CLIPS REF, TYP .035 .002 [0.89 0.06 ] 6 PLATED THROUGH HOLES 4 PLC A .575 [14.61 ] REF PIN 8 REF, TYP PC BOARD LAYOUT PARTS WITH GROUNDING CLIPS = .265[6.73] PARTS WITHOUT GROUNDING CLIPS = .275[6.99] (COMPONENT SIDE) PIN 1 REF, TYP SEE DETAIL FOR -3 & -4 B A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: INCHES [mm] MATERIAL 4805 (3/13) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.25 [.010] - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - 23JUN2005 L. VARELA - DOCK5 CHK 23JUN2005 J. WESTMAN APVD 23JUN2005 S. FLICKINGER DWN PRODUCT SPEC - APPLICATION SPEC - WEIGHT TE Connectivity NAME STACKED MODULAR JACK ASSEMBLY, 2 X 8, 8 POSITION, SHIELDED, PANEL GROUND, OFFSET, CAT 5 SIZE - CUSTOMER DRAWING CAGE CODE A1 00779 DRAWING NO RESTRICTED TO 6116689 SCALE 3:1 SHEET 2 OF 2 REV B