6368062-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 6 5 4 2 20 RELEASED FOR PUBLICATION LOC AA ALL RIGHTS RESERVED. BY - 59.82 8 LED 2 TYP 3 SHIELD HOUSING 8 PANEL GROUND 1.22 REF TYP 22.99 0.43 5.71 8 LED 4 TYP SHIELD SURFACE ACTION PINCOMPLIANT PIN TERMINAL 10 PC BOARD REF P/N 6368062-2 SHOWN GROUND CLIP QUANTITY: 4 FOR -2, -4, -5 & -6 ONLY PANEL SHOWN IN THIS VIEW FOR CLARITY 6 C 1.78 0.61 RECOMMENDED PANEL LOCATION 14.61 TYP YELLOW 2.42 REF GREEN LED CURRENT DIAGRAM 6368062-4,-7 APVD 13FEB2012 JJ AC D REV PER ECR-13-009307 8JUN2013 D.Z S.H E ECO-15-006810 29DEC2015 LL SH 28JUL2020 IT SH D DRILLED HOLE DIA = 1.02±.025. COPPER THICKNESS = 0.025-0.075. TIN LEAD THICKNESS = 0.008 MIN. 4 5 DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 6 DATE CODE LOCATED ON REAR OF PART APPROXIMATELY AS SHOWN. 7 CONTACTS ARE NOT INTENDED TO BE ALIGNED WITH EACH OTHER. 8 SUGGESTED OPERATING CURRENT FOR LEDS IS 20 mA. C 9. TWO LEDS PER PORT, SIZE .079 X .118, SEE TABLE FOR COLOR 10 CLEAR 0.038 MIN THICK SURFACE PROTECTION TAPE APPLIED TO SHIELD SURFACE. FILM DOES NOT HAVE CUTOUTS IN EACH PORT. REMOVE TAPE PRIOR TO MATING A MODULAR PLUG TO THE JACK 11 MATERIAL: SHIELD 0.25 THICK COPPER ALLOY PLATED WITH 1.27 µm MINIMUM SATIN NICKEL. 12 THE PART NUMBER 6368062-7 IS PRELIMINARY. 13 ONLY FOR 6368062-8 CONTACT AREA LUBRICATED WITH BELLCORE APPROVED LUBRICANT TECHNICAL REFERENCE GR-1217-CORE ISSUE 1, NOVEMBER 1995. 14 THE PART 6368062-9 IS ONLY FOR CUSTOMER ZYNX SPECIAL LED LUMINOUS INTENSITY REQUEST.( GREEN:13~20 mcd YELLOW:6~9 mcd.) LED CIRCUIT DIAGRAM 6368062-6 B YELLOW YELLOW GREEN GREEN WITHOUT GROUND CLIP 1-6368062-6 14 YELLOW YELLOW GREEN GREEN WITHOUT GROUND CLIP 6368062-9 13 GREEN GREEN GREEN GREEN WITHOUT GROUND CLIP 6368062-8 - N/A N/A GREEN/YELLOW GREEN/YELLOW WITHOUT GROUND CLIP - RED/GREEN RED/GREEN RED/GREEN RED/GREEN WITH GROUND CLIP 6368062-6 10 GREEN GREEN GREEN GREEN WITH GROUND CLIP 6368062-5 - GREEN/YELLOW GREEN/YELLOW GREEN/YELLOW GREEN/YELLOW WITH GROUND CLIP 6368062-4 - YELLOW YELLOW GREEN GREEN WITHOUT GROUND CLIP 6368062-3 - GREEN GREEN GREEN GREEN WITH GROUND CLIP 6368062-2 - GREEN GREEN GREEN GREEN WITHOUT GROUND CLIP 6368062-1 REMARKS LED #4 (LOWER-RIGHT) LED #3 (UPPER-RIGHT) LED #2 (UPPER-LEFT) LED #1 (LOWER-LEFT) DESCRIPTION PART NUMBER DIMENSIONS: PN 6368062-7 SCALE 2:1 mm MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.13 0.13 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 4805 (3/11) DWN ECR-12-003298 ALL DIMENSIONS ARE NOMINAL UNLESS OTHERWISE SPECIFIED. THIS DRAWING IS A CONTROLLED DOCUMENT. PN 6368062-1,-2,-3,-4,-5,-6,-8 AND 1-6368062-6 SCALE 2:1 DATE 3. RED 11 A DESCRIPTION JACK CAVITY CONFORMS TO FCC RULES AND REGULATIONS, PART 68 SUBPART F. GREEN ANODE (+) ANODE (+) PARTIAL BACK VIEW LTR 2. D/C 0015 B P REVISED PER ECO-21-000623 E1 MATERIAL: HOUSING PBT POLYESTER, BLACK, UL 94V-O. TERMINALS 0.33 THICK PHOSPHOR BRONZE PLATED WITH 1.27µm MINIMUM THICK HARD GOLD IN LOCALIZED AREA AND 3.81µm MINIMUM THICK MATTE TIN IN ACTION PIN COMPLIANT PIN TERMINAL AREA OVER 1.27µm MINIMUM THICK NICKEL UNDERPLATE. SHIELD 0.25 THICK COPPER ALLOY PLATED WITH 1.27 µm MINIMUM NICKEL LIGHT EMITTING DIODE (LED) DIFFUSED EPOXY LENS, 12.95 CARBON STEEL WIREFRAME LEADS PREPLATED WITH 8.89 µm THICK Sn/Cu OVER 2.03 µm THICK Ag OVER 1.02 µm THICK Cu OVER 3.56 µm THICK Ni OVER 1.02 µm THICK Cu UNDERPLATE LED ACTION PIN - COMPLIANT PIN CONTACTS 0.3 THICK BRASS PLATED WITH 2um MINIMUM MATTE TIN OVER 1.27um MINIMUM NICKEL UNDERPLATE. 1. 7 LED 1 TYP 22 C4 18.36 8 REVISIONS DIST 31.06 LED 3 TYP D 1 - DWN 15APR2005 CHK 15APR2005 APVD 15APR2005 L.A.MAYER J.WESTMAN S.FLICKINGER PRODUCT SPEC 108-1854 APPLICATION SPEC 1 114-2160 WEIGHT Customer Drawing 12 A TE Connectivity NAME STACKED MODULAR JACK ASSEMBLY, 2x4 OFFSET, WITH LEDS, 8 POSN, RJ45 SHIELDED, PANEL GROUNDS, CAT 5 SIZE - 6368062-7 CAGE CODE A1 00779 DRAWING NO 6368062 SCALE 4:1 SHEET 1 RESTRICTED TO OF - 2 REV E1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 6 5 4 3 2 20 RELEASED FOR PUBLICATION LOC AA ALL RIGHTS RESERVED. BY - 1 REVISIONS DIST 22 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 60.71 D D PC BOARD REF 23.88 6.18 REF TOP OF PC BOARD RECOMMENDED PANEL CUT-OUT 2.8 C 5 C 1 -X5 X.XX 54.24 5.34 4 0.89 0.06 PLATED THROUGH HOLES 0.89 43.82 0.06 TYP 4 0.89 14.61 TYP LED 3 TYP PIN 8 REF TYP B 1.13 14.61 2.03 TYP PLATED THROUGH HOLES 4 PLC 5.33 2 PLC 29.21 1.02 TYP 1.62 TYP 8 & -6 B 4.06 TYP 1 LED 2 TYP DETAIL B PLATED PADS REQUIRED FOR 6368062-2, -4, -5 (PRODUCT WITH GROUNDING CLIPS) SCALE 10:1 4 PLACES 3 PLC 4.76 TYP 2.54 2 PLC 0.06 8 2.54 TYP 1 2.54 TYP 5 -Y3.81 2 PLC A 15.88 WITH GROUNDING CLIPS 16.13 WITHOUT GROUNDING CLIPS PARTS WITH GROUNDING CLIPS = 1.65 PARTS WITHOUT GROUNDING CLIPS = 1.91 4805 (3/11) LED 1 TYP PIN 1 REF TYP 2.73 TYP 2.54 TYP 2.03 TYP LED 4 TYP CATHODE TYP ANODE TYP 14.61 TYP PC BOARD LAYOUT (COMPONENT SIDE) LED #3,#4 NOT REQUIRED FOR 6368062-7 SEE DETAIL B 2.54 TYP A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.13 0.13 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - - DWN 15APR2005 CHK 15APR2005 APVD 15APR2005 L.A.MAYER J.WESTMAN S.FLICKINGER PRODUCT SPEC 108-1854 APPLICATION SPEC 1 114-2160 WEIGHT TE Connectivity NAME STACKED MODULAR JACK ASSEMBLY, 2x4 OFFSET, WITH LEDS, 8 POSN, RJ45 SHIELDED, PANEL GROUNDS, CAT 5 SIZE - Customer Drawing CAGE CODE A1 00779 DRAWING NO 6368062 SCALE 4:1 SHEET 2 RESTRICTED TO OF - 2 REV E1