650092-2

Card Edge Connectors Catalog 1654080 Issued 7-03 Card Edge Connectors Introduction This catalog contains product descriptions of AMP Card Edge Connectors. These connectors are presented in three groups: Solder Type Board-toBoard, Press-fit Board-toBoard, and Wire-to-Board connectors. To assist you in the selection of the appropriate connector for your application, a selection guide is provided at the beginning of each section. See the Table of Contents on the following page for the exact location. A comprehensive description and features of a partic- Need more information? Call Technical Support at the numbers listed at the bottom of the catalog pages. Technical Support is staffed with specialists well versed in Tyco Electronics products. They can provide you with: Technical Support Catalogs ■ Technical Documents ■ Product Samples ■ Tyco Electronics Authorized Distributor Locations ular printed circuit board connector family are provided at the beginning of that section. Various technical documents are referenced in the connector family sections and are listed and described at the rear of this catalog. The Tyco Electronics products presented in this catalog are designed and manufactured according to the highest possible standards of quality and craftsmanship. They offer optimum reliability at the lowest possible cost. Dimensioning: Dimensions are in inches and millimeters unless specified otherwise. Values in brackets are metric equivalents. Metric symbols used are: m (meter) mm (millimeter) mm2 (square millimeter) kg (kilogram) C (Celsius) N (newton) Note: Dimensions in this catalog are for reference purposes only. Customer drawings are available upon request. ■ ■ © Copyright 1992, 1996 and 2002 by Tyco Electronics. All Rights Reserved. AMP, ACTION PIN, AMP-DURAGOLD, AMP-LEAF, AMP-O-LECTRIC, AMP-O-MATIC, AMPOMATOR, AMP PACE, CERTI-CRIMP, DUO-TYNE, ECONOMATE, TELEDENSITY, and TYCO are trademarks. Other products, logos, and company names mentioned herein may be trademarks of their respective owners. Produced under a Quality Management System certified to ISO 9001 A copy of the certificate is available upon request 2 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Table of Contents Solder Type Board-to-Board Connectors Introduction………………………………………………………………………………………2 Selection Guide ………………………………………………………………………………4-6 Standard Edge Series Connectors Standard Edge .050 PCI Card Edge Connectors ………………………………………7-10 Standard Edge .050 Series Connectors ………………………………………………11-14 Standard Edge II Connectors ……………………………………………………………15-27 Cantilever Beam Dip Solder Tails Overview ……………………………………………………28 .100" [2.54] Centerline ……………………………………………………………………29-34 .125" [3.18] Centerline ……………………………………………………………………35-37 .156" [3.96] Centerline ……………………………………………………………………38-40 Modified Bellows Contact Overview ……………………………………………………………41 .100" [2.54] Centerline ……………………………………………………………………42-47 .125" [3.18] Centerline ……………………………………………………………………48-52 .156" [3.96] Centerline ……………………………………………………………………53-56 Polarization Keys ………………………………………………………………………………57 Standard Daughter Card Layout …………………………………………………………………57 Low Profile Connectors ……………………………………………………………………58-63 Twin Leaf Mother Board Connectors ………………………………………………………64-72 Rotary Cam ZIF Connectors …………………………………………………………………73-82 Linear ZIF Connectors ………………………………………………………………………83-96 Press-Fit Board-to-Board Connectors ACTION PIN Press-Fit Contacts ……………………………………………………………97 AMP PACE Connectors …………………………………………………………………98-115 TELEDENSITY Connectors ……………………………………………………………116-118 ECONOMATE Connectors ……………………………………………………………119-126 Cantilever Beam Press-Fit Connectors Overview ……………………………………………127 .050" [1.27] High Density ………………………………………………………………128-129 .100" [2.54] Centerline …………………………………………………………………130-140 .125" [3.18] Centerline …………………………………………………………………141-144 .156" [3.96] Centerline …………………………………………………………………145-148 Application Tooling ……………………………………………………………………149-151 Wire-to-Board Connectors Introduction …………………………………………………………………………………152 Selection Guide ………………………………………………………………………………153 Crimp Snap Twin Leaf Connectors …………………………………………………154-163 AMP-LEAF Connectors…………………………………………………………………164-172 High Current Connectors ………………………………………………………………173-176 DUO-TYNE Flag Connectors …………………………………………………………177-180 Printed Circuit Board Connector Hood Assemblies ………………………………181-183 Application Tooling ……………………………………………………………………184,185 Technical Documents ……………………………………………………………………186,187 Part Number Index ………………………………………………………………………188-201 Tyco Electronics Related Product Information ………………………………………………202 3 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Selection Guide, Board-to-Board Connectors Introduction Board-to-board (mother/ daughter board) connectors are ideally suited to backplane wiring or any other application requiring the circuit connection of one printed circuit board to another. Designed to shorten manufacturing time and reduce applied costs, these one-step, pre-assembled connectors are ready for mounting and mass insertion. Board-to-board connectors come in a range of contact centerline spacings of .050 [1.27] to .156 [3.96]. A wide range of dual position sizes and post styles are available. One family of connectors features zero insertion force of the daughter board, along with a choice of actuating devices. A variety of housing and contact materials further expands the choice of connectors available to meet many application requirements. Many of the connectors are available with the proven and reliable ACTION PIN contact. This unique contact has superior electrical and physical characteristics that are top of the line in the industry. Standard Edge .050 Series PCI Connectors (Pages 7-10) To help in choosing a connector for your application, a Selection Guide is provided on pages 4 through 6. Standard Edge .050 Series Connectors (Pages 11-14) Standard Edge II Connectors (.100 and .125 Centerline) (Pages 15-27) .350 [8.89] .300 [7.62] .368 [9.35] .155 [3.94] .300 [7.62] .610 [15.49] .610 [15.49] .170±.020 [4.32±0.51] .610 [15.49] .315 [8.00] .170±.020 [4.32±0.51] Centerlines .050 [1.27] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] X X X X Tail Styles Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount X X X X X X 4 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Selection Guide, Board-to-Board Connectors (Continued) Standard Edge II Connectors (.150 Centerline) (Pages 15-27) Cantilever Beam Connectors Standard Housing (Pages 28-40) Cantilever Beam Connectors Scoop Housing (Pages 28-40) .370 [9.40] .390 [9.91] .054–.070 [1.37-1.78] .045 [1.14] .145 [3.68] .015 [0.33] .008 [.203] .365 [9.27] .054 to .071 [1.37 to 1.80] .020±.010 [.51±.25] .300 [7.62] .610 [15.49] .705 [17.91] .200±.020 [5.08±0.51] .135±.020 [3.43±0.51] .200 [.508] .395 or .510 [10.03 or 12.95] .015 [0.41] Centerlines X X X X X X X X X X X .050 [1.27] .0625 [1.588] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] Tail Styles X Low Profile Connectors (Pages 58-63) Modified Bellows Connector (Pages 41-56) .368 [9.35] .054-.071 [1.37-1.80] .300 [7.62] .610 [15.49] Twin Leaf Mother Board Connectors (Pages 64-72) .437 [11.10] .125 [3.18] .460 [11.68] .165 [4.19] Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount .400 [10.16] .150 [3.81] .610 [15.49] .235 [5.97] .200 [5.08] .025 [.63] Centerlines X X X X X X X X X X X X X X .050 [1.27] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] Tail Styles X Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount 5 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Selection Guide, Board-to-Board Connectors (Continued) Rotary Cam ZIF Connectors (Pages 73-82) Linear ZIF Connectors (Pages 83-96) .140 [3.56] AMP PACE Connectors, Card Scoop Housing (Pages 98-115) .475 [12.07] .450 [11.43] A .440 [11.18] .150 [3.81] .234 [5.94] .845 [21.46] .815 [20.70] .645 [16.38] .848 [21.54] .490 [12.45] .460 [11.68] .598 [15.19] .370 [9.40] .345 [8.76] .130 [3.30] .100 x .200 = .390 [9.91] A .125 x .125 = .420 [10.67] .125 x .200 = .420 [10.67] Centerlines .050 [1.27] .0625 [1.588] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] X X X X X X X Tail Styles Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount X X X X AMP PACE Connectors, Standard Housing (Pages 98-115) X X X X High Density Press Fit Connector For .093 Cards (Pages 128-129) ECONOMATE Connectors (Pages 119-126) .400 [10.16] A .234 [5.94] .066 [1.68] .415 [10.54] .545 [13.84] .545 [13.84] .181 [4.60] .610 [15.49] .421 .461 [10.69] [11.71] .130 [3.30] A .100 x .100 = .380 [9.65] .100 x .200 = .360 [9.14] .125 x .250 = .410 [10.41] .156 x .200 = .360 [9.14] Centerlines .050 [1.27] .0625 [1.588] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] X X X X X X Tail Styles Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount X X X X 6 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors Product Facts ■ ■ ■ ■ High density .050 [1.27] centerline contact spacing Easy mating of high circuit count daughter boards Polarizing web for positive board-to-connector registration Choice of plastic pylons or metal holddowns Connectors that support PCI expansion cards are derived from those on the MicroChannel Architecture (MCA) bus. The MCA connectors are well defined and have proven value and reliability. There are four connectors that can be used depending upon the PCI implementation. The differences between these connectors are 32 bit and 64 bit, and the 5 volt and 3.3 volt signaling environments. PCI-X is a version of PCI at 133 MHz which is under development and employs standard PCI connectors. PCI-X is limited to 1 slot versus 4 slots of PCI. A key differentiates the signaling environment voltages. The same physical connector is used for the 32 bit signaling environments. In one orientation, the key accepts 5 volt boards. When rotated 180°, the connector accepts 3.3 volt signaling boards. The pin numbering of the connector changes for the different signaling environments to maintain the same relative position of signals on the connector. Performance Specifications: Durability—Tested to 100 mating cycles Mating Force—8 oz [2.22 N] max. per contact pair Unmating Force—.5 oz [0.14 N] min. per contact pair Contact Resistance—20 milliohms max. (initial) 30 milliohms max. (final) Insulation Resistance— 1000 megohms min. Dielectric Withstanding Voltage— 500 VAC (at sea level) Capacitance—2 picofarads max. Current Rating—1 ampere max. Voltage Rating—203 VAC Thermal Shock— –55°C to +85°C for 5 cycles Mixed Flowing Gas—Class II with mated board for 20 days Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Qualification Test Report 501-203 7 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors 64 Bit, 5 Volt Signaling Plastic Pylons 92 Dual Positions with 3 Plastic Pylons or 3 Metal Holddowns .350 [8.89] 5.040 [128.02] Material and Finish: Housing—High temperature thermoplastic 94V-0 rated, white Contacts—Phosphor bronze, plated as follows: Plating B—Duplex plated .000015 [0.00038] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating C—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .035 [0.89] (2 Plcs.) L .300 [7.62] 35° (2 Plcs.) .610 [15.49] .170±.020 [4.32±0.51] L ±.010 W [±0.25] Typ. .075 [1.90] (2 Plcs.) See Note. .050 48 Spaces at [1.27] .060 [1.52] Typ. .150 [3.81] 31 Spaces .050 at [1.27] 10 Spaces .050 at [1.27] .050 Solder Tail CL [1.27] (2 Plcs.) .150 [3.81] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 7 Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Through Hole Metal Holddowns .035 [0.89] (2 Plcs.) L 35° (2 Plcs.) Surface Mount .170±.020 [4.32±0.51] .300 [7.62] .610 [15.49] .078 [1.98] Ref. See Note. .075 [1.90] (2 Plcs.) .150 [3.81] 10 Spaces .050 at [1.27] 31 Spaces .050 at [1.27] L ±.010 W [±0.25] Typ. 48 Spaces at .050 [1.27] .060 [1.52] Typ. .150 [3.81] (2 Plcs.) .180 [4.57] .180 [4.57] Section L-L .100 2.54 Plating B Plating C .125 3.18 Surface Mount Plating C 145166-8 145169-8 Plating C — 145113-1 Contact Finish .17+.02 [4.318+.508] .003 [.076] .050 Solder [1.27] Tail CL (2 Plcs.) Part Numbers 5 Volt 3 Plastic 3 Metal Pylons Holddowns 145166-2 — 145166-4 145169-4 W (Post Length) .300 [7.62] Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 8 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors 32 Bit, 3.3 and 5 Volt Signaling Plastic Pylons .350 [8.89] 60 Dual Positions with 2 Plastic Pylons or 2 Metal Holddowns 3.340 [84.84] Material and Finish: Housing Y—High temperature thermoplastic 94V-0 rated, white Housing Z—Nylon 6/6, white Contacts—Phosphor bronze, plated as follows: Plating A—Duplex plated gold flash in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating B—Duplex plated .000015 [0.00038] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating C—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .035 [0.89] (2 Plcs.) L .300 [7.62] .610 [15.49] ±.010 W [±0.25] Typ. L .075 [1.90] (2 Plcs.) 10 Spaces .050 at [1.27] 48 Spaces at Metal Holddowns .050 [1.27] .035 [0.89] (2 Plcs.) L .150 [3.81] (2 Plcs.) .060 [1.52] Typ. See Note. Through Hole 35° (2 Plcs.) Product Specification 108-14034 Application Specification 114-26012 .078 [1.98] .003 Ref. [.076] Typ. .075 [1.90] (2 Plcs.) 10 Spaces .050 at [1.27] See Note. .050 48 Spaces at [1.27] .150 [3.81] (2 Plcs.) .050 Solder [1.27] Tail CL (2 Plcs.) .17+.02 [4.318+.508] .180 [4.57] .180 [4.57] Section L-L Plating A Plating B Plating C Plating A Plating B Part Numbers 2 Plastic 2 Metal Pylons Holddowns 145154-1 145167-1 145154-2 — 145154-4 145167-4 11299-1 — 11299-6 — Y Plating C 145154-8 — Y Plating C — 145098-1 W (Post Length) Housing Material .100 2.54 Y .118 3.00 Z .125 3.18 Surface Mount .060 [1.52] Typ. .300 [7.62] .300 [7.62] .610 [15.49] L Surface Mount .170±.020 [4.32±0.51] Technical Documents: ±.010 W [±0.25] .050 Solder Tail CL [1.27] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 7 .170±.020 [4.32±0.51] 35° (2 Plcs.) Contact Finish Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 9 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors 64 Bit, 3.3 Volt Signaling Plastic Pylons 92 Dual Positions with 3 Plastic Pylons or 3 Metal Holddowns .350 [8.89] 5.040 [128.02] Material and Finish: Housing—High temperature thermoplastic 94V-0 rated, white Contacts—Phosphor bronze, plated as follows: Plating B—Duplex plated .000015 [0.00038] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating C—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .035 [0.89] (2 Plcs.) L 35° (2 Plcs.) .170±.020 [4.32±0.51] .300 [7.62] .610 [15.49] ±.010 W [±0.25] Typ. .075 [1.90] (2 Plcs.) 10 Spaces .050 at [1.27] 48 Spaces at 31 Spaces .050 at [1.27] .050 [1.27] .150 [3.81] (2 Plcs.) .060 [1.52] Typ. L See Note. .150 [3.81] .050 Solder Tail CL [1.27] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 7 Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Through Hole Metal Holddowns .035 [0.89] (2 Plcs.) L 35° (2 Plcs.) Surface Mount .170±.020 [4.32±0.51] .300 [7.62] See Note. L ±.010 W [±0.25] Typ. 10 Spaces .050 at [1.27] .075 [1.90] (2 Plcs.) .300 [7.62] .610 [15.49] .17+.02 [4.318+.508] .078 [1.98] .003 Ref. [.076] .150 [3.81] 31 Spaces .050 at [1.27] .050 48 Spaces at [1.27] .060 [1.52] Typ. .150 [3.81] (2 Plcs.) .050 Solder [1.27] Tail CL (2 Plcs.) .180 [4.57] .180 [4.57] Section L-L W (Post Length) Contact Finish .100 2.54 Plating B Plating C Part Numbers 3.3 Volt 3 Plastic 3 Metal Pylons Holddowns — 145168-2 1-145165-4 145168-4 .125 3.18 Surface Mount Plating C 1-145165-8 — Plating C — 145246-1 Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 10 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Product Facts ■ ■ ■ ■ ■ ■ ■ High density .050 [1.27] centerline spacing of contacts Easy mating of high-circuit count daughter boards Compatible with infrared reflow (IR) soldering techniques Polarizing web for positive board-to-connector registration Choice of plastic pylons or metal holddowns Recognized under the Component Program of Underwriter Laboratories Inc. File No. E28476 Certified by Canadian Standards Association, ® File No. LR 7189 Performance Specifications: Contact Current Rating* —1 ampere Termination Resistance — 20 milliohms max. (initial) 30 milliohms max. (final) Dielectric Withstanding Voltage — 500 VAC min. Insulation Resistance — 1000 megohms min. Mating Force — .5 oz. [0.14 N] per contact pair Unmating Force — 1 oz. [0.3 N] per contact pair Durability (Tested to) — 100 mating cycles Application Temperature — +215°C for 120 seconds max. Temperature Range — –55°C to +85°C *Consult Tyco Electronicsengineering when paralleling contacts for power applications. The need to conserve space and pack more function into a given area has demanded that .050 [1.27] centerline spacing become a reality. AMP Standard Edge .050 Series connectors are the ideal vehicle for mother/daughter board applications requiring this real estate. These rugged connectors have two rows of contacts on .050 [1.27] centerlines. Polarizing webs provide positive board-to-connector registration, while insertion force allows even high circuit-count daughter boards to mate easily. The connectors accept .054 to .070 [1.37 to 1.78] thick daughter boards and feature an overstress protected contact design. AMP Standard Edge .050 Series connectors are ideal for fast automated robotic assembly with registration features and dimensional tolerancing for more accurate pickup and placement, and are packaged in roboticscompatible trays. Plastic guide posts or metal holddowns align the connector with the mother board and retain it for soldering. To make circuit routing easy, connector solder posts are arranged in a four-row .100 [2.54] staggered grid. Hightemperature tolerant materials promote that these connectors withstand infrared reflow (IR) soldering, while standoffs ease flux cleaning. High Density for DataBus Applications 11 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Configuration; 1 Key—2 Plastic Pylons .350 [8.89] Material and Finish: Housing—High temperature thermoplastic, brown Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel C .035 [0.89] (2 Plcs.) L .170±.020 [4.32±0.51] 35° (2 Plcs.) .300 [7.62] .610 [15.49] Related Product Data: Performance Specifications— page 11 Technical Documents: W (Post Length) Product Specification 108-14034 Application Specification 114-26012 .075 [1.90] (2 Plcs.) .012 [0.30] Typ. .060 Typ. [1.52] L B Spaces .050 at [1.27] A Spaces .050 at [1.27] .150 [3.81] (2 Plcs.) Section L-L .016 Typ. [0.41] No. of Dual Positions A Dimensions B 23 10 11 30 10 18 1.490 37.85 1.840 46.74 40 10 28 2.340 59.44 C 45 10 33 2.590 65.79 56 10 44 3.140 79.76 41 4.340 110.24 80 91 37 41 48 .050 [1.27] (2 Plcs.) 4.890 124.21 W (Post Length) .100 2.54 .100 2.54 .100 2.54 .140 3.56 .100 2.54 .100 2.54 .140 3.56 .100 2.54 .100 2.54 .140 3.56 PC Board Hole Layout Connector Part Numbers A 0-650090-7 B 0-650090-6 B 0-650090-3 B 0-650181-2 A 0-650090-2 B 10-650090-11 B 0-650181-1 C 0-650090-9 A 10-650092-12 A 0-650092-2 1 Connector used for VLLocal Bus and MCA Bus applications. used for MCA Bus applications. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. .125 [3.18] post length is available, consult Tyco Electronics. 2 Connector 12 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Configuration; 1 Key—2 Plastic Pylons .350 [8.89] Material and Finish: Housing—High temperature thermoplastic, brown Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel D .035 [0.89] (2 Plcs.) L .170±.020 [4.32±0.51] 35° (2 Plcs.) .300 [7.62] .610 [15.49] Related Product Data: Performance Specifications— page 11 Technical Documents: W (Post Length) Product Specification 108-14034 .075 [1.90] (2 Plcs.) L B Spaces .050 at [1.27] A Spaces .050 at [1.27] C Spaces .050 at [1.27] .060 Typ. [1.52] .012 [0.30] Typ. .150 [3.81] (2 Plcs.) .150 [3.81] Application Specification 114-26012 .050 [1.27] (2 Plcs.) Section L-L .016 Typ. [0.41] .096 Dia. Max. [2.44] No. of Dual Positions A Dimensions B C 66 10 44 9 D 3.740 95.00 W (Post Length) .100 2.54 .140 3.56 PC Board Hole Layout Connector Part Numbers A 1650091-1* A 650091-2 *Connectors used for MCA Bus applications. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. .125 [3.18] post length is available, consult Tyco Electronics. 13 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Configuration; 1 Key/1 Web —3 Metal Holddowns .350 [8.89] 120 Dual Positions 6.440 [163.58] Material and Finish: .035 [0.89] (2 Plcs.) L Housing—High temperature thermoplastic, brown Holddowns—Brass, plated .000150 [0.00381] min. tin-lead over .000050 [0.00127] min. nickel Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel 35° (2 Plcs.) .300 [7.62] .610 [15.49] .170±.020 [4.32±0.51] W (Post Length) .150 [3.81] 63 Spaces .050 at [1.27] 44Spaces .050 at [1.27] 10Spaces .050 at [1.27] .180 [4.57] .060 Typ. [1.52] L .075 [1.90] (2 Plcs.) .150 [3.81] (2 Plcs.) .050 Solder Tail C L [1.27] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 11 Technical Documents: No. of Dual Positions Product Specification 104-14034 Application Specification 114-26012 W (Post Length) .140 3.56 120 Connector Part Numbers 145031-3 Note: Other connector sizes can be made available, consult Tyco Electronics. Configuration; End Key .096 [2.44] Dia. Max. Material and Finish: Housing—High temperature thermoplastic, brown Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .016 Typ. [0.41] .350 [8.89] .099 [2.52] Max. B .035 [0.89] L 35° Related Product Data: .170±.020 [4.32±0.51] .300 [7.62] Performance Specifications— page 11 .610 [15.49] Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Post Length .012 Typ. [0.30] .050 [1.27] (2 Plcs.) .060 Typ. [1.52] L .075 [1.90] .150 [3.81] (2 Plcs.) A Spaces .050 at [1.27] Section L-L No. of Dual Positions A B 25 24 1.480 37.59 Dimensions C 1.350 34.29 D 1.310 33.27 Post Length .100 2.54 Connector Part Numbers 650719-1 Note: Other connector sizes can be made available, consult Tyco Electronics. 14 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors Product Facts ■ ■ ■ ■ ■ ■ ■ ■ Maximum number of dual positions .100 [2.54] Centerlines-70, .125 [3.18] Centerlines-50, .150 [3.81] Centerlines-31 Selective gold plating of contacts for high performance at low cost .025 [0.64] square solid posts meet standard wraptype specifications For flow solder applications Glass-filled polyester housing is 94V-0 rated Accepts double sided PC boards, .054-.070 [1.27-1.78] thick Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association, File No. LR 7189 Performance Specifications Contact Rating*: 3 amperes continuous (UL and CSA) Contact Resistance: 10 milliohms max. Operating Temperature: –55°C to +85°C Voltage Rating (Sea Level): .100 [2.54] centerline—1000 VAC (test) .125 [3.18] centerline—1500 VAC (test) .150 [3.81] centerline—1500 VAC (test) Insulation Resistance: 5000 megohms min., after exposure to humidity Vibration Tolerance: 10 to 500 hertz Contact Engagement Force: 12 oz [3.3 N] average per pair with .062 [1.57] PC board Contact Separation Force: 2 oz [0.6 N] average per pair with .062 [1.57] PC board AMP Standard Edge II Connectors provide high reliability and economy in packages compatible with industry standards for double sided printed circuit boards. Tyco Electronics offers Standard Edge II Connectors with or without mounting ears, for rack mounting and soldering. Contacts are arranged on .100 [2.54] centers, .125 [3.18] centers, .150 [3.81] centers, .200 [5.08] row-to-row; and .250 [6.35] row-to-row. Right-angle connectors are also available with contacts arranged on .100 [2.54] centers, .150 [3.81] row-to-row or .200 [5.08] row-to-row. Card extenders with contacts on .100 [2.54] and .125 [3.18] centers also are available. Precision formed phosphor bronze contacts are selectively gold plated. Phosphor bronze has excellent strength characteristics which help the connector absorb load deflection movement of a PC board while maintaining sufficient contact force for good electrical connection. Bifurcated cantilever beam contacts provide redundant contact. Humidity Tolerance: 90%-95% for 96 hours *Consult Tyco Electronics engineering when paralleling contacts for power applications. 15 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors Styles .100 [2.54] Centerline Right-Angle Posts with Low and No Mounting Ears Page 23 .100 [2.54] and .125 [3.18] Centerline Solder Posts without Mounting Ears Pages 17 and 18 .100 [2.54] and .125 [3.18] Centerline Solder Posts with Low and Mid-High Mounting Ears Page 20 .100 [2.54] and .125 [3.18] Centerline Wrap-Type Posts with Mid-High Mounting Ears Page 21 .100 [2.54] and .125 [3.18] Centerline Card Extenders Page 22 .100 [2.54] Centerline Solder Posts with Board Retention Feature, without Mounting Ears Page 24 .150 [3.81] Centerline Solder Posts (with Board Retention Feature), without Mounting Ears Page 19 16 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Centerline, Vertical Solder Posts, Without Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .064 [1.63] Sq. x .130 [3.30] Dp. Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, duplex plated as follows: Plating A—.000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated Plating B—.000015 [0.00038] gold in contact area, tin on posts, with entire contact nickel underplated Plating C—Gold flash in contact area, tin on posts, with entire contact nickel underplated .100 [2.54] .368 [9.35] D C** .141/.153 [3.58/3.88] Retention Feature (Open End Card Slot) Accepts .054/.070 [1.37/1.77] PC Board A .295 [7.49] .550 [13.97] .610 [15.49] .100 Typ. [2.54] .060 [1.52] B .155 [3.94] Post Length .191 [4.85] Technical Documents: Product Specification 108-9039 No. of Dual Positions 3 Intercontact Keying Plug 6 Material: 10 Natural color polyester 12 15 17 18 20 Part Number 650025-2 (.100 [2.54] Centerline) 22 25 28 30 31 36 40 50 Dimensions B C** A .560 14.22 .860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 1.960 49.78 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.860 98.04 4.260 108.20 5.260 133.60 .450 11.43 .750 19.05 1.150 29.21 1.350 34.29 1.650 41.91 1.850 46.99 1.950 49.53 2.150 54.61 2.350 59.69 2.650 67.31 2.950 74.93 3.150 80.01 3.250 82.55 3.750 95.25 4.150 105.41 5.150 130.81 Open End .700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.700 93.98 4.100 104.14 5.100 129.54 D .200 5.08 .500 12.70 .900 22.86 1.100 27.94 1.400 35.56 1.600 40.64 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.500 88.90 3.900 99.06 4.900 124.46 Post Length* Plating A Part Numbers Plating B Plating C .125 10-650263-1 1 — — .125 .187 .125 .187 7-530843-5 7-530843-6 5-530843-0 4-530843-9 — — — — .125 0-530843-1 — — .125 0-530843-2 — — .125 5-530843-3 — — .125 0-530843-3 2-530843-7 1176137-11 .125 5-530843-4 — — .125 0-530843-4 — — .125 0-530843-5 — — .125 0-530843-6 — — .125 .187 0-530843-7 1-530843-8 — — .125 6-530843-5 7-530843-0 — .125 0-530843-8 — — .187 2-530843-0 — — .125 1-530843-1 — — **Metric equivalent for post lengths are .125 = 3.18; .187 = 4.75. **C dimension is card slot length. 1 Connectors with Retention Feature. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 17 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .125 [3.18] Centerline, Vertical Solder Posts, Without Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .064 [1.63] Sq. x .130 [3.30] Dp. Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .125 [3.18] .368 [9.35] D C** Retention Feature Accepts .054/.070 [1.37/1.77] PC Board A Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .191/.203 [4.85/5.16] .295 [7.49] .550 [13.97] .610 [15.49] .155 [3.94] .125 [3.18] Technical Documents: (pages 186, 187): Post Length .241 [6.11] .060 [1.52] B Product Specification 108-9039 Intercontact Keying Plug Material: Natural color polyester No. of Dual Positions 6 14 18 22 28 Part No. 650025-1 (.125 [3.18] Centerline) 30 36 40 43 50 Dimensions C** A B 1.035 26.29 2.035 51.69 2.535 64.39 3.035 77.09 3.785 96.14 4.035 102.49 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 .875 22.22 1.875 47.62 2.375 60.33 2.875 73.03 3.625 92.08 3.875 98.42 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 .875 22.22 1.875 47.62 2.375 60.33 2.875 73.03 3.625 92.08 3.875 98.42 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 D .625 15.88 1.625 41.28 2.125 53.98 2.625 66.68 3.375 85.73 3.625 92.08 4.375 111.13 4.875 123.82 5.250 133.35 6.125 155.58 Post Length* .125 Part Numbers 650207-11 .187 5-530844-8 .187 1-530844-5 .187 1-530844-6 .187 1-530844-7 .187 1-530844-8 .187 1-530844-9 .187 2-530844-0 .125 1-530844-0 .125 .187 1-530844-1 2-530844-2 **Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. Note: Other connector sizes can be made available, consult Tyco Electronics. 18 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .150 [3.81] Centerline, Vertical Solder Posts, Retention Feature, Without Mounting Ears Inter-Contact Keying Slot Card Slot Accepts .054-.070 [1.37-1.78] Printed Circuit Board B ±.010 [±0.25] +.005 .432 -.010 [10.97] +0.13 -0.25 Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .305 [9.27] .045 [1.14] Contact Area .015 [0.38] .080 [.203] Lead in .200±.020 Area [5.08±0.51] .016 [0.41] .020 [0.51] .035±.020 [3.430±0.51] .200 [5.08] Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .600 [15.21] .024 [0.61] .020 [0.51] No. of Dual Positions 12 19 28 31 0.143–.161 [3.63–4.03] .025 [0.63] Spaces at .150 = Dim A Ref. [3.81] Dimensions A B Retention Location Post Length* Part Numbers 1.650 41.91 2.700 68.58 4.050 102.87 4.500 114.30 1.920 48.77 2.970 75.44 4.320 109.73 4.770 121.16 7-10, 15-18 7-10, 29-32 7-10, 25-32,47-50 7-10, 27-34,53-56 .135 1-650728-2 .135 1-650728-9 .135 2-650728-9 .135 3-650728-1 **Metric equivalent for post length is .135 = [3.43] **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 19 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .100 [2.54] and .125 [3.18] Centerline, Vertical Solder Posts, Low and Mid-High Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot G Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .368 [9.35] H .150 [3.81] .300 .128 Dia. [7.62] [3.25] D C** Accepts .054/.070 [1.37/1.77] PC Board F .360 [9.14] A .550 [13.97] .610 [15.49] .155 [3.94] Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .295 [7.49] .250 [6.35] .060 [1.52] B E J Post Length .180 [4.57] Low Mounting Ears Technical Documents: (pages 186, 187): Product Specification 108-9039 .250 [6.35] Intercontact Keying Plugs Material: Natural color polyester Retention Feature Mid-High Mounting Ears .100 [2.54] Centerline No. of Dual Positions 15 18 25 30 36 Part No. 650025-2 (.100 [2.54] Centerline) .141/.153 [3.58/3.88] 50 A B C** D Dimensions E F G H J 1.760 44.70 2.060 52.32 2.760 70.10 3.260 82.80 3.860 98.04 1.650 41.91 1.950 49.53 2.650 67.31 3.160 80.01 3.750 95.25 1.600 40.64 1.900 48.26 2.600 66.04 3.100 78.74 3.700 93.98 1.400 35.56 1.700 43.18 2.400 60.96 2.900 73.66 3.500 88.90 2.385 67.18 2.645 67.18 3.345 84.96 3.845 97.66 4.445 112.90 2.075 52.71 2.375 60.32 3.075 78.11 3.575 90.81 4.175 106.21 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .191 4.85 .191 4.85 .191 4.85 .191 4.85 .191 4.85 .191 4.85 .141-.153 3.58-3.88 5.260 133.60 5.150 130.81 5.100 129.54 4.900 124.46 5.845 148.46 5.575 141.60 .100 2.54 .100 2.54 Post Length* Part Numbers .125 0-530841-2 .125 0-530841-3 .125 .187 0-530841-5 1-530841-6 .187 1-530841-8 .125 0-530841-8 .125 .187 1-530841-1 2-530841-2 .125 0-650718-11,2 **Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. 2Connector with Mid-High Mounting Ears. Note: Other connector sizes can be made available, consult Tyco Electronics. .125 [3.18] Centerline No. of Dual Positions A B C** D Dimensions E F G H J 6 1.035 26.29 .875 22.22 .875 22.22 .625 15.88 1.555 39.50 1.295 32.89 .125 3.18 .125 3.18 28 3.785 96.14 3.505 89.03 3.625 92.08 3.375 85.73 4.305 109.35 4.045 102.74 .125 3.18 .125 3.18 .241 6.11 .241 6.11 .241 6.11 6.535 165.99 6.255 158.88 6.375 161.93 6.125 155.58 7.055 179.20 6.795 172.59 .125 3.18 .125 3.18 50 Part No. 650025-1 (.125 [3.18] Centerline) 20 Catalog 1654080 Issued 7-03 www.tycoelectronics.com .241 6.11 Post Length* Part Numbers .125 1-531341-3 .187 1-530842-7 .187 23-531341-02 .125 1-530842-1 **Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. 2Connector with Mid-High Mounting Ears. Note: Other connector sizes can be made available, consult Tyco Electronics. Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .100 [2.54] and .125 [3.18] Centerline, Vertical WrapType Posts, Mid-High Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. .064 [1.63] Sq. x .130 [3.30] Dp. .150 [3.81] Intercontact Key Slot Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .128 Dia. [3.25] G .368 [9.35] D H C F .180 [4.57] A Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .300 [7.62] Accepts .054/.070 [1.37/1.77] PC Board .295 [7.49] .550 [13.97] .250 .610 [15.49] [6.35] .155 [3.94] .060 [1.52] Technical Documents: B (pages 186, 187): Post Length E J Product Specification 108-9039 Intercontact Keying Plugs Material: Natural color polyester .100 [2.54] Centerline No. of Dual Positions A B C** D Dimensions E F G H 3.260 3.150 3.100 2.900 3.845 3.575 .100 .100 82.80 80.01 78.74 73.66 97.41 90.80 2.54 2.54 3.860 3.750 3.700 3.500 4.435 4.175 .100 .100 36 98.04 95.25 93.98 88.90 112.65 106.04 2.54 2.54 4.260 4.150 4.100 3.900 4.845 4.575 .100 .100 40 108.20 105.41 104.14 99.06 123.06 116.21 2.54 2.54 **Metric equivalent for post length is .570 = [14.48]. **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 30 Part No. 650025-2 (.100 [2.54] Centerline) Post Length* Part Numbers .570 3-530396-3 .570 3-530396-4 .570 3-530396-4 J Post Length* Part Numbers .250 6.35 .570 4-530825-5 J .200 5.08 .200 5.08 .200 5.08 .125 [3.18] Centerline No. of Dual Positions A B C** D Dimensions E F G H 3.035 2.755 2.875 2.625 3.555 3.295 .125 .125 77.09 69.98 73.02 66.67 90.30 83.69 3.18 3.18 **Metric equivalent for post length is .570 = [14.48]. **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 22 Part No. 650025-1 (.125 [3.18] Centerline) 21 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .100 [2.54] and .125 [3.18] Centerlines, Card Extender Contacts Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .064 [1.63] Sq. x .130 [3.30] Dp. .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .128 Dia. [3.25] .368 [9.35] D H .300 [7.62] .150 [3.81] G .180 [4.67] C Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 E F Accepts .054/.070 [1.37/1.77] PC Board .180 [4.57] A Technical Documents: .295 [7.49] (pages 186, 187): Product Specification 108-9039 .550 [13.97] .610 [15.49] .155 [3.94] Mounting Block Material: .060 [1.52] Natural color nylon .062 Dia. [1.57] Roll Pin .250 [6.35] .340 [8.63] B Fits .054/.070 [1.37/1.77] PC Board Card Extender Connector Housing Ref. #5 Self Tapping Screws .100 [2.54] Centerline No. of Dual Positions Mounting Block .062 [1.57] PC Board Ref. Kit Part No.531250-4 Each kit includes 2 mounting blocks, 2 self tapping screws, #5 x .437 [11.10] and 2 roll pins, .075 x .250 [1.57 x 6.35] A B C** Dimensions D E F 5.260 5.160 5.100 4.900 5.845 5.575 133.60 130.81 129.54 124.46 148.46 141.60 *C dimension is card slot length. 1No mounting ears. Note: Other connector sizes can be made available, consult Tyco Electronics. 50 G H .100 2.54 .100 2.54 G H .125 3.18 .125 3.18 Part Numbers 530826-3 Intercontact Keying Plugs Material: Natural color polyester .125 [3.18] Centerline No. of Dual Positions A B C** Dimensions D E F 4.785 4.505 4.625 4.375 5.035 5.045 121.54 114.43 117.48 111.13 134.75 128.14 *C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 36 Part No. 650025-1 (.125 [3.18] Centerline) Part Numbers 530384-2 Part Number 650025-2 (.100 [2.54] Centerline) 22 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Right-Angle Solder Posts, with Low and No Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Accepts .054/.070 [1.37/1.77] PC Board .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .295 [7.49] Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, duplex plated as follows: Plating A—.000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated Plating B—.000015 [0.00038] gold in contact area, tin on posts, with entire contact nickel underplated .368 [9.35] .100 [2.54] .100 [2.54] .155 [3.94] .300 [7.62] G D C Post Length With Board Locks E Accepts .054/.070 [1.37/1.77] PC Board F Related Product Data: A Performance Specifications— page 15 .295 [7.49] .550 [13.97] .610 [15.49] G Technical Documents: Product Specification 108-9039 .250 [6.25] .128 Dia. [3.25] .155 [3.94] .080 [1.82] B Post Length Low Mounting Ears Intercontact Keying Plug Material: Natural color polyester Low Mounting Ears No. of Dual Positions 12 18 20 Part Number 650025-2 (.100 [2.54] Centerline) A B C* 1.460 37.08 2.060 52.32 2.260 57.40 1.350 34.29 1.950 49.53 2.150 54.61 1.300 33.02 1.900 48.26 2.100 53.34 Dimensions D E 1.100 27.94 1.700 43.18 1.900 48.26 2.045 51.94 2.645 67.18 2.845 72.30 F G1 1.775 45.08 2.375 60.32 2.575 65.40 x.100x .150 x.100x .150 x.100x .150 Post Length2 Part Numbers (Plating A) .090 3145089-13 .090 645384-1 .090 645384-3 *C dimension is card slot length. 1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08]. 2 Metric equivalent for post length is .090 = [2.27]. 3 Connector with Board Locks. Note: Other connector sizes can be made available, consult Tyco Electronics. No Mounting Ears No. of Dual Positions 15 17 25 31 32 19 A B 1.760 44.70 1.960 49.78 2.760 70.10 3.360 85.34 3.460 87.88 2.160 54.86 1.650 41.91 1.850 46.99 2.350 67.61 3.250 82.55 3.350 85.09 2.750 69.85 Dimensions C* D 1.600 40.64 1.800 45.72 2.600 66.04 3.200 81.28 3.300 83.82 2.700 68.58 1.400 35.56 1.600 40.64 2.400 60.96 3.000 76.20 3.100 78.74 1.800 45.72 G1 .100x .150 .100x .200 .100x .150 .100x .150 .100x .150 .100x .150 Post Length2 Part Numbers Plating A Plating B .090 650118-1 — .090 650187-1 — .090 — 532600-2 .090 — 532600-4 .090 — 532600-5 .090 — 532600-6 *C dimension is card slot length. 1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08]. 2 Metric equivalent for post length is .090 = [2.27]. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 23 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Centerline Vertical Solder Posts, Retention Feature, Without Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .064 [1.63] Sq. x .130 [3.30] Dp. Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, duplex plated as follows: Plating A—.000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated Plating B—.000015 [0.00038] gold in contact area, tin on posts, with entire contact nickel underplated Plating C—Gold flash in contact area, tin on posts, with entire contact nickel underplated .368 [9.35] .100 [2.54] D C Accepts .054/.070 [1.37/1.77] PC Board A .295 [7.49] .550 [13.97] .610 [15.49] .155 [3.94] Technical Documents: Product Specification 108-9039 .060 [1.52] Post Length .191 [4.85] .100 Typ. [2.54] B Intercontact Keying Plug Material: Natural color polyester .141/.153 [3.58/3.88] Retention Feature Part Number 650025-2 (.100 [2.54] Centerline) No. of Dual Positions 18 31 50 60 A 2.060 52.32 3.360 85.34 5.260 133.60 6.260 159.00 Dimensions B C** 1.950 49.53 3.250 82.55 5.150 130.81 6.150 156.21 1.900 48.26 3.200 81.28 5.100 129.54 6.100 154.94 D 1.700 43.18 3.000 76.20 4.900 124.46 5.900 149.86 Post Length* Retention Feature PartNumbers Plating A .125 3-6, 31-34 1-645235-4 .125 3-6, 29-32 or 31-34, 57-60 3-6, 49-52, 95-98 3-6, 55-58, 63-66, 115-118 1-645235-1 .125 .125 1-645235-3 1-645235-8 **Metric equivalent for post length is .125 = [3.18]. **C dimension is card slot length. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 24 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Centerline, Special 18/31 Dual Combination Connector, Vertical Solder Posts, Without Mounting Ears .200 [5.08] .100 [2.54] .368 [9.35] .100 [2.54] Material and Finish: 1.900 [48.26] .141/.153 [3.58/3.88] 3.200 [81.28] Housing—Black glass-filled polyester, 94V-0 rated, except where noted Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area (except where noted), tin on posts, with entire contact nickel underplated Retention Feature 5.460 [138.68] Accepts .054/.070 [1.37/1.77] PC Board .550 [13.97] .610 [15.49] Technical Documents: .295 [7.49] Product Specification 108-9039 .400 [10.16] .060 [1.52] A A Solder Posts 5.350 [135.89] Intercontact Keying Plug .191 [4.85] Material: Natural color polyester Part Number 650025-2 (.100 [2.54] Centerline) No. of Dual Positions Post Type 52 Solder Posts 52 Solder Posts 52 Solder Posts 52 Solder Posts 52 Solder Posts Dimension Retention A Feature .125 3.18 .125 3.18 .125 3.18 .125 3.18 .187 4.75 Part Numbers 3-6, 41, 42, 51, 52, 93-96 1536128-11 645169-2 None 645169-3 3-14, 41, 42, 51, 52, 85-96 5, 6, 31, 32, 41, 42, 93, 94 2176139-12 2 None 650616-1 645169-4 Housing material is high temperature glass-filled polyester, gray. Contact area is gold flash. Notes: 1. Card slot length is 5.300 [134.62]. 2. Other connector sizes can be made available, consult Tyco Electronics. 3. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 1 2 25 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) Recommended PC Board Hole Layouts Vertical Post Connectors D B ±.003 C [±0.08] Dia. .128 Dia. [3.25] A F A B Dimensions C .100 2.54 .150 3.81 .125 3.18 .100/.125 2.54/3.18 .100 2.54 .125 3.18 .200 5.08 .200 5.08 .250 6.35 .200/.250 5.08/6.35 .200 5.08 .250 6.35 .040 1.02 .040 1.02 .040 1.02 .040 1.02 .042 1.07 .042 1.07 Connector Type Solder Post/Retention Solder Post/Retention Solder Post, Mounting Ears Solder Post, W/O Mounting Ears Wrap-Type Post Wrap-Type Post Notes: 1. 2. 3. 4. 5. D F See Note 1 See Note 2 See Note 4 See Note 2 See Note 3 See Note 3 See Note 4 See Note 2 See Note 5 See Note 5 See Note 5 See Note 5 Refer to page 24 for D Dimensions and Dual Positions. No mounting ears. Dimensions do not apply. Refer to page 20 for D and F Dimensions and Dual Positions. Refer to pages 18 and 19 for D Dimensions and Dual Positions. Refer to page 21 for D and F Dimensions and Dual Positions. Right-Angle Post Connectors F D B .128 Dia. [3.25] ±.003 C [±0.08] Dia. A G .337 [8.56] Connector Type Right-Angle Posts, Mounting Ears Right-Angle Posts, No Mounting Ears A .100 2.54 .100 2.54 B .150 3.81 .150 or .200 3.81 or 5.08 C .042 1.07 .042 1.07 Dimensions D F See Note 1 See Note 1 G .137 3.48 See Note 2 See Note 3 See Note 3 Notes: 1. Refer to page 23 for D and F Dimensions and Dual Positions. 2. Refer to page 23 for D Dimensions and Dual Positions. 3. No Mounting Ears, Dimensions do not apply. 26 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) Recommended PC Board Edge Pattern PC Board Edge Pattern for .100 [2.54] and .125 [3.18] Centerline .050 [1.27] Intercontact Key Slot Datum CL .015 x 45° [0.38] Chamfer .295 Min. [7.49] Engagement Depth .310 Min. [7.87] B .054/.070 [1.37/1.77] ±.005 A D [±0.13] ±.005 C [±0.13] No. of Dual Positions 3 6 10 12 13 .100 [2.54] Centerline A = .093 [2.36] B = .050 [1.27] C D .386 .200 9.80 5.08 .686 .500 17.42 12.70 1.086 .900 27.58 22.86 1.286 1.100 32.66 27.94 1.386 1.200 35.20 30.48 .125 [3.18] Centerline A = .118 [3.00] B = .075 [1.90] C D — — .861 21.87 1.361 34.57 .625 15.88 1.125 28.58 — — — — 1.625 41.28 — 14 — — 1.861 47.27 15 1.586 40.28 1.786 45.36 1.886 47.90 2.286 58.06 2.586 65.68 2.886 73.30 3.086 78.38 3.186 80.92 3.586 91.08 3.686 93.62 4.086 103.78 4.386 111.40 5.086 129.18 6.086 154.58 7.086 179.98 1.400 35.56 1.600 40.64 1.700 43.18 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 6.900 175.26 — 17 18 22 25 28 30 31 35 36 40 43 50 60 70 — — 2.361 59.97 2.861 72.67 2.125 53.98 2.625 66.68 — — 3.611 91.72 3.861 98.07 3.986 101.24 3.375 85.73 3.625 92.08 3.750 95.25 — — 4.611 117.12 5.111 129.82 5.486 139.34 6.361 161.57 4.375 111.13 4.875 123.82 5.250 133.35 6.125 155.58 — — — — 27 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Card Edge Connectors Product Facts Double readout Card Edge connectors use dip solder contacts ■ Large lead-in chamfers allow easy PC board installation ■ Insulator standoffs prevent solder from wicking ■ Various lengths for custom applications ■ Contact option, single or dual row ■ Description Design Advantages The Cantilever Beam Series products from Tyco Electronics are double readout cardedge connectors, using dip solder contacts. Tooled for flexible manufacturing, these Card Edge connectors are readily available in a broad assortment of sizes and mounting styles. Our connectors meet industry standards. • Circuit Integrity: Robust cantilever contacts are designed to promote optimal normal forces at the lowest possible cost. Our uniquely contoured contact mating surface gives you constant engagement, even when subjected to continuous vibration. • Ease of Assembly: Generous lead-in chamfers let your P.C. board slide easily into the connector. Insulator standoffs are provided to facilitate cleaning and prevent solder from wicking. Availability, flexibility, performance and very low cost make the Cantilever Series from Tyco Electronics the clear choice in Card Edge connectors. Cantilever Beam The Cantilever Beam Card Edge connector comes with standard high temperature plastic insulators. Contacts are available in a variety of lengths to accommodate various custom applications. Standoffs allow for cleaning and draining and are available as an option on most insulator bodies. Cantilever Beam Card Edge offers a variety of card slot depths. A full scoop option is available for ease of installation in applications where visibility is limited. Contact options vary in this series from dual row standard contacts, single row options and press-fit. 28 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .020±.010Contact Gap [.51±.25] .145 [3.68] Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .300 Card Slot Depth [7.62] .13 [3.30] .200 [5.08] .400 [10.16] 1.700 [43.18] 3.000 [76.20] .100 [2.54] .200 [5.08] .040±.003 Dia. [1.02±.080] Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms 5.460 [138.68] 5.300 [134.62] 1.900 [48.26] 3.70 [9.40] Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 .100 Ref. [2.54] 3.200 [81.28] .200 Ref. [5.08] 5.100 [129.54] .300 [7.62] .610 [15.49] .06 [1.52] .06 [1.52] .100 Typ. [2.54] Ordering Information Acquired Part Number C8D52DS29C1M191 – Insulator with molded-in polarizing key with card guide chamber. The card slot lengths are 1.900 [48.26] and 3.200 [81.28]. Includes retention tails for .062 [1.57] PCB to hold connectors securely during handling. C8D52DS29C1M195 – Same as above. No retention tails. 29 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline Dip Solder Tails, .300 [7.62] Card Slot Depth Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ D E Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .020±.010Contact Gap [.51±.25] .145 [3.68] .370 [9.40] .300 Card Slot Depth [7.62] J .100 Typ. [2.54] .200 [5.08] B A C .250 [6.35] .610 [15.49] Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .060 .180 [1.52] [4.57] .020 Typ. Dia. [0.51] E Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .040±.003 [1.02±.08] Dia. .128 [3.25] Dia. Dim E Related Product Data: Daughter Card Edge Pattern— page 57 .200 [5.08] .100 [2.54] Mounting Styles .125 [3.18] Dia. #4-40 .125 [3.18] Dia. .250 [6.35] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole .250 [6.35] Flush Mounting Ear 4-40 Threaded Insert 30 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Mounting Ear Options Dimensions A B C D E Tail Length .130" [3.30] (DIM “J”) 1.435 1.175 6 36.45 29.85 10 1.835 1.575 46.61 40.01 2 . 0 3 5 1 .775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3 . 0 3 5 2 .775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3 . 9 3 5 3 .675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 5.835 5.575 50 148.21 141.61 6.835 6.575 60 173.61 167.01 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 Tail Length .160" [4.06] (DIM “J”) 1.435 1.175 6 36.45 29.85 1.835 1.575 10 46.61 40.01 2 . 0 3 5 1 .775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3 . 0 3 5 2 .775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3 . 9 3 5 3 .675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C8D06DS29A1 C8D06DS29B1 C8D06DS29C1 C8D06DS29D1 C8D06DS29E1 C8D10DS29A1 C8D10DS29B1 C8D10DS29C1 C8D10DS29D1 C8D10DS29E1 C8D12DS29A1 C8D12DS29B1 C8D12DS29C1 C8D12DS29D1 C8D12DS29E1 C8D15DS29A1 C8D15DS29B1 C8D15DS29C1 C8D15DS29D1 C8D15DS29E1 C8D18DS29A1 C8D18DS29B1 C8D18DS29C1 C8D18DS29D1 C8D18DS29E1 C8D20DS29A1 C8D20DS29B1 C8D20DS29C1 C8D20DS29D1 C8D20DS29E1 C8D22DS29A1 C8D22DS29B1 C8D22DS29C1 C8D22DS29D1 C8D22DS29E1 C8D25DS29A1 C8D25DS29B1 C8D25DS29C1 C8D25DS29D1 C8D25DS29E1 C8D28DS29A1 C8D28DS29B1 C8D28DS29C1 C8D28DS29D1 C8D28DS29E1 C8D30DS29A1 C8D30DS29B1 C8D30DS29C1 C8D30DS29D1 C8D30DS29E1 C8D31DS29A1 C8D31DS29B1 C8D31DS29C1 C8D31DS29D1 C8D31DS29E1 C8D35DS29A1 C8D35DS29B1 C8D35DS29C1 C8D35DS29D1 C8D35DS29E1 C8D36DS29A1 C8D36DS29B1 C8D36DS29C1 C8D36DS29D1 C8D36DS29E1 C8D40DS29A1 C8D40DS29B1 C8D40DS29C1 C8D40DS29D1 C8D40DS29E1 C8D43DS29A1 C8D43DS29B1 C8D43DS29C1 C8D43DS29D1 C8D43DS29E1 C8D50DS29A1 C8D50DS29B1 C8D50DS29C1 C8D50DS29D1 C8D50DS29E1 C8D60DS29A1 C8D60DS29B1 C8D60DS29C1 C8D60DS29D1 C8D60DS29E1 C8D06DS29A2 C8D06DS29B2 C8D06DS29C2 C8D06DS29D2 C8D06DS29E2 C8D10DS29A2 C8D10DS29B2 C8D10DS29C2 C8D10DS29D2 C8D10DS29E2 C8D12DS29A2 C8D12DS29B2 C8D12DS29C2 C8D12DS29D2 C8D12DS29E2 C8D15DS29A2 C8D15DS29B2 C8D15DS29C2 C8D15DS29D2 C8D15DS29E2 C8D18DS29A2 C8D18DS29B2 C8D18DS29C2 C8D18DS29D2 C8D18DS29E2 C8D20DS29A2 C8D20DS29B2 C8D20DS29C2 C8D20DS29D2 C8D20DS29E2 C8D22DS29A2 C8D22DS29B2 C8D22DS29C2 C8D22DS29D2 C8D22DS29E2 C8D25DS29A2 C8D25DS29B2 C8D25DS29C2 C8D25DS29D2 C8D25DS29E2 C8D28DS29A2 C8D28DS29B2 C8D28DS29C2 C8D28DS29D2 C8D28DS29E2 C8D30DS29A2 C8D30DS29B2 C8D30DS29C2 C8D30DS29D2 C8D30DS29E2 C8D31DS29A2 C8D31DS29B2 C8D31DS29C2 C8D31DS29D2 C8D31DS29E2 C8D35DS29A2 C8D35DS29B2 C8D35DS29C2 C8D35DS29D2 C8D35DS29E2 C8D36DS29A2 C8D36DS29B2 C8D36DS29C2 C8D36DS29D2 C8D36DS29E2 C8D40DS29A2 C8D40DS29B2 C8D40DS29C2 C8D40DS29D2 C8D40DS29E2 C8D43DS29A2 C8D43DS29B2 C8D43DS29C2 C8D43DS29D2 C8D43DS29E2 31 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Mounting Ear Options Dimensions A B C D E Tail Length .160" [4.06] (DIM “J”) (Continued) 5.835 5.575 5.260 50 148.21 141.61 133.60 6.835 6.575 6.260 60 173.61 167.01 159.00 5.100 129.54 6.100 154.94 4.900 124.46 5.900 149.86 Tail Length .220" [5.59] (DIM “J”) 1.435 1.175 6 36.45 29.85 1.835 1.575 10 46.61 40.01 2.035 1.775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2 . 8 3 5 2 .575 20 72.01 65.41 3.035 2.775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3 . 8 3 5 3 .575 30 97.41 90.81 3.935 3.675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 5.835 5.575 50 148.21 141.61 6.835 6.575 60 173.61 167.01 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C8D50DS29A2 C8D50DS29B2 C8D50DS29C2 C8D50DS29D2 C8D50DS29E2 C8D60DS29A2 C8D60DS29B2 C8D60DS29C2 C8D60DS29D2 C8D60DS29E2 C8D06DS29A3 C8D06DS29B3 C8D06DS29C3 C8D06DS29D3 C8D06DS29E3 C8D10DS29A3 C8D10DS29B3 C8D10DS29C3 C8D10DS29D3 C8D10DS29E3 C8D12DS29A3 C8D12DS29B3 C8D12DS29C3 C8D12DS29D3 C8D12DS29E3 C8D15DS29A3 C8D15DS29B3 C8D15DS29C3 C8D15DS29D3 C8D15DS29E3 C8D18DS29A3 C8D18DS29B3 C8D18DS29C3 C8D18DS29D3 C8D18DS29E3 C8D20DS29A3 C8D20DS29B3 C8D20DS29C3 C8D20DS29D3 C8D20DS29E3 C8D22DS29A3 C8D22DS29B3 C8D22DS29C3 C8D22DS29D3 C8D22DS29E3 C8D25DS29A3 C8D25DS29B3 C8D25DS29C3 C8D25DS29D3 C8D25DS29E3 C8D28DS29A3 C8D28DS29B3 C8D28DS29C3 C8D28DS29D3 C8D28DS29E3 C8D30DS29A3 C8D30DS29B3 C8D30DS29C3 C8D30DS29D3 C8D30DS29E3 C8D31DS29A3 C8D31DS29B3 C8D31DS29C3 C8D31DS29D3 C8D31DS29E3 C8D35DS29A3 C8D35DS29B3 C8D35DS29C3 C8D35DS29D3 C8D35DS29E3 C8D36DS29A3 C8D36DS29B3 C8D36DS29C3 C8D36DS29D3 C8D36DS29E3 C8D40DS29A3 C8D40DS29B3 C8D40DS29C3 C8D40DS29D3 C8D40DS29E3 C8D43DS29A3 C8D43DS29B3 C8D43DS29C3 C8D43DS29D3 C8D43DS29E3 C8D50DS29A3 C8D50DS29B3 C8D50DS29C3 C8D50DS29D3 C8D50DS29E3 C8D60DS29A3 C8D60DS29B3 C8D60DS29C3 C8D60DS29D3 C8D60DS29E3 32 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors 100 x .200 [2.54 x 5.08], .510 [12.95] and .395 [10.03] Card Slot Depth, Full Scoop Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [3.37 to 1.80] Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .180 [4.57] A B C .02 [.51] Contact Gap .390 [9.91] .100 [2.54] Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms Card Slot Depth .705 [17.91] Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 C Related Product Data .180 [4.57] Dim C .040±.003 [1.02±.08] Dia. Daughter Card Edge Pattern— page 57 .200 [5.08] .100 [2.54] 33 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row Full Scoop Dimensions No. of Dual Readout Pos. A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Number .510" [12.95] Card Slot Depth 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18DS29063 W8D20DS29063 W8D22DS29063 W8D25DS29063 W8D28DS29063 W8D30DS29063 W8D35DS29063 W8D36DS29063 W8D40DS29063 W8D43DS29063 W8D45DS29063 W8D50DS29063 W8D60DS29063 .395" [10.03] Card Slot Depth 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18DS29093 W8D20DS29093 W8D22DS29093 W8D25DS29093 W8D28DS29093 W8D30DS29093 W8D35DS29093 W8D36DS29093 W8D40DS29093 W8D43DS29093 W8D45DS29093 W8D50DS29093 W8D60DS29093 34 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors .125 x .250 [3.18 x 6.35] Centerline, Dip Solder Tails, .300 [7.62] Card Slot Depth Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .020±.010Contact Gap [.51±.25] .145 [3.68] .300 Card Slot Depth [7.62] J D .250 [6.35] E Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .370 [9.40] .100 Typ. [2.54] B A C .250 [6.35] .610 [15.49] Electrical Properties: Operation Voltage—1000 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .060 .180 [1.52] [4.57] .020 Typ. Dia. [0.51] E Environmental Properties: Dim B Operating Temperature— -55˚C to +125˚C Temperature Cycling— .128 [3.25] Dia. MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 .040±.003 [1.02±.08] Dia. Dim E Related Product Data: Daughter Card Edge Pattern— page 57 .250 [6.35] .125 [3.18] Mounting Styles .125 [3.18] Dia. #4-40 .125 [3.18] Dia. .250 [6.35] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole .250 [6.35] Flush Mounting Ear 4-40 Threaded Insert 35 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B C D E Tail Length .130 [3.30] (DIM. “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2 . 6 8 0 2 .420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4 . 3 0 5 4 .045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 4.680 4.420 31 118.87 112.27 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Tail Length .160 [4.06] (DIM. “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2.680 2.420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3 . 9 3 0 3 .670 25 99.82 93.22 4.305 4.045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 4.680 4.420 31 118.87 112.27 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C7D06DS29A1 C7D06DS29B1 C7D06DS29C1 C7D06DS29D1 C7D06DS29E1 C7D10DS29A1 C7D10DS29B1 C7D10DS29C1 C7D10DS29D1 C7D10DS29E1 C7D15DS29A1 C7D15DS29B1 C7D15DS29C1 C7D15DS29D1 C7D15DS29E1 C7D18DS29A1 C7D18DS29B1 C7D18DS29C1 C7D18DS29D1 C7D18DS29E1 C7D22DS29A1 C7D22DS29B1 C7D22DS29C1 C7D22DS29D1 C7D22DS29E1 C7D25DS29A1 C7D25DS29B1 C7D25DS29C1 C7D25DS29D1 C7D25DS29E1 C7D28DS29A1 C7D28DS29B1 C7D28DS29C1 C7D28DS29D1 C7D28DS29E1 C7D30DS29A1 C7D30DS29B1 C7D30DS29C1 C7D30DS29D1 C7D30DS29E1 C7D31DS29A1 C7D31DS29B1 C7D31DS29C1 C7D31DS29D1 C7D31DS29E1 C7D35DS29A1 C7D35DS29B1 C7D35DS29C1 C7D35DS29D1 C7D35DS29E1 C7D36DS29A1 C7D36DS29B1 C7D36DS29C1 C7D36DS29D1 C7D36DS29E1 C7D40DS29A1 C7D40DS29B1 C7D40DS29C1 C7D40DS29D1 C7D40DS29E1 C7D43DS29A1 C7D43DS29B1 C7D43DS29C1 C7D43DS29D1 C7D43DS29E1 C7D50DS29A1 C7D50DS29B1 C7D50DS29C1 C7D50DS29D1 C7D50DS29E1 C7D06DS29A3 C7D06DS29B3 C7D06DS29C3 C7D06DS29D3 C7D06DS29E3 C7D10DS29A3 C7D10DS29B3 C7D10DS29C3 C7D10DS29D3 C7D10DS29E3 C7D15DS29A3 C7D15DS29B3 C7D15DS29C3 C7D15DS29D3 C7D15DS29E3 C7D18DS29A3 C7D18DS29B3 C7D18DS29C3 C7D18DS29D3 C7D18DS29E3 C7D22DS29A3 C7D22DS29B3 C7D22DS29C3 C7D22DS29D3 C7D22DS29E3 C7D25DS29A3 C7D25DS29B3 C7D25DS29C3 C7D25DS29D3 C7D25DS29E3 C7D28DS29A3 C7D28DS29B3 C7D28DS29C3 C7D28DS29D3 C7D28DS29E3 C7D30DS29A3 C7D30DS29B3 C7D30DS29C3 C7D30DS29D3 C7D30DS29E3 C7D31DS29A3 C7D31DS29B3 C7D31DS29C3 C7D31DS29D3 C7D31DS29E3 C7D35DS29A3 C7D35DS29B3 C7D35DS29C3 C7D35DS29D3 C7D35DS29E3 C7D36DS29A3 C7D36DS29B3 C7D36DS29C3 C7D36DS29D3 C7D36DS29E3 C7D40DS29A3 C7D40DS29B3 C7D40DS29C3 C7D40DS29D3 C7D40DS29E3 C7D43DS29A3 C7D43DS29B3 C7D43DS29C3 C7D43DS29D3 C7D43DS29E3 C7D50DS29A3 C7D50DS29B3 C7D50DS29C3 C7D50DS29D3 C7D50DS29E3 36 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B Tail Length .220 [5.59] (DIM. “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2.680 2.420 15 68.07 61.47 3 . 0 5 5 2 .795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4.305 4.045 28 109.35 102.74 4 . 5 5 5 4.295 30 115.70 109.09 4.680 4.420 31 118.87 112.27 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 C D E 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C7D06DS29A4 C7D06DS29B4 C7D06DS29C4 C7D06DS29D4 C7D06DS29E4 C7D10DS29A4 C7D10DS29B4 C7D10DS29C4 C7D10DS29D4 C7D10DS29E4 C7D15DS29A4 C7D15DS29B4 C7D15DS29C4 C7D15DS29D4 C7D15DS29E4 C7D18DS29A4 C7D18DS29B4 C7D18DS29C4 C7D18DS29D4 C7D18DS29E4 C7D22DS29A4 C7D22DS29B4 C7D22DS29C4 C7D22DS29D4 C7D22DS29E4 C7D25DS29A4 C7D25DS29B4 C7D25DS29C4 C7D25DS29D4 C7D25DS29E4 C7D28DS29A4 C7D28DS29B4 C7D28DS29C4 C7D28DS29D4 C7D28DS29E4 C7D30DS29A4 C7D30DS29B4 C7D30DS29C4 C7D30DS29D4 C7D30DS29E4 C7D31DS29A4 C7D31DS29B4 C7D31DS29C4 C7D31DS29D4 C7D31DS29E4 C7D35DS29A4 C7D35DS29B4 C7D35DS29C4 C7D35DS29D4 C7D35DS29E4 C7D36DS29A4 C7D36DS29B4 C7D36DS29C4 C7D36DS29D4 C7D36DS29E4 C7D40DS29A4 C7D40DS29B4 C7D40DS29C4 C7D40DS29D4 C7D40DS29E4 C7D43DS29A4 C7D43DS29B4 C7D43DS29C4 C7D43DS29D4 C7D43DS29E4 C7D50DS29A4 C7D50DS29B4 C7D50DS29C4 C7D50DS29D4 C7D50DS29E4 37 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series .156 x .200 [3.96 x 5.08] Centerline, Dip Solder Tails, .300 [7.62] Card Slot Depth Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .020±.010Contact Gap [.51±.25] .145 [3.68] D .300 Card Slot Depth [7.62] J .200 [5.08] E Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .370 [9.40] .156 Typ. [3.96] B A C .250 [6.35] .610 [15.49] Electrical Properties: Operation Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .060 .180 [1.52] [4.57] .020 Typ. Dia. [0.51] E Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .040±.003 [1.02±.08] Dia. .128 [3.25] Dia. Dim E Related Product Data: Daughter Card Edge Pattern— page 57 .200 [5.08] .156 [3.96] Mounting Styles .125 [3.18] Dia. #4-40 .125 [3.18] Dia. .250 [6.35] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole .250 [6.35] Flush Mounting Ear 4-40 Threaded Insert 38 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B Tail Length .130 [3.30] (DIM. “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3 . 1 8 8 2 .938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 3.968 3.718 20 100.79 94.44 4.280 4.030 22 108.71 102.36 4 . 7 4 8 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 5.528 5.278 30 140.41 134.06 5.684 5.434 31 144.37 138.02 6.308 6.058 35 160.22 153.87 6.464 6.214 36 164.19 157.84 7.088 6.838 40 180.04 173.69 7.556 7.306 43 191.92 185.57 8.648 8.398 50 219.66 213.31 Tail Length .160 [4.06] (DIM. “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3.188 2.938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 3 . 9 6 8 3 .718 20 100.79 94.44 4.280 4.030 22 108.71 102.36 4.748 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 5.528 5.278 30 140.41 134.06 5.684 5.434 31 144.37 138.02 6.308 6.058 35 160.22 153.87 6.464 6.214 36 164.19 157.84 7.088 6.838 40 180.04 173.69 7.556 7.306 43 191.92 185.57 8.648 8.398 50 219.66 213.31 C D E 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 8.085 205.36 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.595 91.31 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 7.964 202.29 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 7.644 194.16 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 8.085 205.36 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.595 91.31 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 7.964 202.29 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 7.644 194.16 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C6D06DS29A1 C6D06DS29B1 C6D06DS29C1 C6D06DS29D1 C6D06DS29E1 C6D10DS29A1 C6D10DS29B1 C6D10DS29C1 C6D10DS29D1 C6D10DS29E1 C6D12DS29A1 C6D12DS29B1 C6D12DS29C1 C6D12DS29D1 C6D12DS29E1 C6D15DS29A1 C6D15DS29B1 C6D15DS29C1 C6D15DS29D1 C6D15DS29E1 C6D18DS29A1 C6D18DS29B1 C6D18DS29C1 C6D18DS29D1 C6D18DS29E1 C6D20DS29A1 C6D20DS29B1 C6D20DS29C1 C6D20DS29D1 C6D20DS29E1 C6D22DS29A1 C6D22DS29B1 C6D22DS29C1 C6D22DS29D1 C6D22DS29E1 C6D25DS29A1 C6D25DS29B1 C6D25DS29C1 C6D25DS29D1 C6D25DS29E1 C6D28DS29A1 C6D28DS29B1 C6D28DS29C1 C6D28DS29D1 C6D28DS29E1 C6D30DS29A1 C6D30DS29B1 C6D30DS29C1 C6D30DS29D1 C6D30DS29E1 C6D31DS29A1 C6D31DS29B1 C6D31DS29C1 C6D31DS29D1 C6D31DS29E1 C6D35DS29A1 C6D35DS29B1 C6D35DS29C1 C6D35DS29D1 C6D35DS29E1 C6D36DS29A1 C6D36DS29B1 C6D36DS29C1 C6D36DS29D1 C6D36DS29E1 C6D40DS29A1 C6D40DS29B1 C6D40DS29C1 C6D40DS29D1 C6D40DS29E1 C6D43DS29A1 C6D43DS29B1 C6D43DS29C1 C6D43DS29D1 C6D43DS29E1 C6D50DS29A1 C6D50DS29B1 C6D50DS29C1 C6D50DS29D1 C6D50DS29E1 C6D06DS29A3 C6D06DS29B3 C6D06DS29C3 C6D06DS29D3 C6D06DS29E3 C6D10DS29A3 C6D10DS29B3 C6D10DS29C3 C6D10DS29D3 C6D10DS29E3 C6D12DS29A3 C6D12DS29B3 C6D12DS29C3 C6D12DS29D3 C6D12DS29E3 C6D15DS29A3 C6D15DS29B3 C6D15DS29C3 C6D15DS29D3 C6D15DS29E3 C6D18DS29A3 C6D18DS29B3 C6D18DS29C3 C6D18DS29D3 C6D18DS29E3 C6D20DS29A3 C6D20DS29B3 C6D20DS29C3 C6D20DS29D3 C6D20DS29E3 C6D22DS29A3 C6D22DS29B3 C6D22DS29C3 C6D22DS29D3 C6D22DS29E3 C6D25DS29A3 C6D25DS29B3 C6D25DS29C3 C6D25DS29D3 C6D25DS29E3 C6D28DS29A3 C6D28DS29B3 C6D28DS29C3 C6D28DS29D3 C6D28DS29E3 C6D30DS29A3 C6D30DS29B3 C6D30DS29C3 C6D30DS29D3 C6D30DS29E3 C6D31DS29A3 C6D31DS29B3 C6D31DS29C3 C6D31DS29D3 C6D31DS29E3 C6D35DS29A3 C6D35DS29B3 C6D35DS29C3 C6D35DS29D3 C6D35DS29E3 C6D36DS29A3 C6D36DS29B3 C6D36DS29C3 C6D36DS29D3 C6D36DS29E3 C6D40DS29A3 C6D40DS29B3 C6D40DS29C3 C6D40DS29D3 C6D40DS29E3 C6D43DS29A3 C6D43DS29B3 C6D43DS29C3 C6D43DS29D3 C6D43DS29E3 C6D50DS29A3 C6D50DS29B3 C6D50DS29C3 C6D50DS29D3 C6D50DS29E3 39 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B Tail Length .220" [5.59] (DIM. “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3 . 1 8 8 2 .938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 3.968 3.718 20 100.79 94.44 4.280 4.030 22 108.71 102.36 4 . 7 4 8 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 5.528 5.278 30 140.41 134.06 5.684 5.434 31 144.37 138.02 6.308 6.058 35 160.22 153.87 6.464 6.214 36 164.19 157.84 7.088 6.838 40 180.04 173.69 7.556 7.306 43 191.92 185.57 8.648 8.398 50 219.66 213.31 C D E 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 8.085 205.36 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.595 91.31 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 7.964 202.29 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 7.644 194.16 Centered Mounting Ear .125" [3.18] ThruHole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C6D06DS29A4 C6D06DS29B4 C6D06DS29C4 C6D06DS29D4 C6D06DS29E4 C6D10DS29A4 C6D10DS29B4 C6D10DS29C4 C6D10DS29D4 C6D10DS29E4 C6D12DS29A4 C6D12DS29B4 C6D12DS29C4 C6D12DS29D4 C6D12DS29E4 C6D15DS29A4 C6D15DS29B4 C6D15DS29C4 C6D15DS29D4 C6D15DS29E4 C6D18DS29A4 C6D18DS29B4 C6D18DS29C4 C6D18DS29D4 C6D18DS29E4 C6D20DS29A4 C6D20DS29B4 C6D20DS29C4 C6D20DS29D4 C6D20DS29E4 C6D22DS29A4 C6D22DS29B4 C6D22DS29C4 C6D22DS29D4 C6D22DS29E4 C6D25DS29A4 C6D25DS29B4 C6D25DS29C4 C6D25DS29D4 C6D25DS29E4 C6D28DS29A4 C6D28DS29B4 C6D28DS29C4 C6D28DS29D4 C6D28DS29E4 C6D30DS29A4 C6D30DS29B4 C6D30DS29C4 C6D30DS29D4 C6D30DS29E4 C6D31DS29A4 C6D31DS29B4 C6D31DS29C4 C6D31DS29D4 C6D31DS29E4 C6D35DS29A4 C6D35DS29B4 C6D35DS29C4 C6D35DS29D4 C6D35DS29E4 C6D36DS29A4 C6D36DS29B4 C6D36DS29C4 C6D36DS29D4 C6D36DS29E4 C6D40DS29A4 C6D40DS29B4 C6D40DS29C4 C6D40DS29D4 C6D40DS29E4 C6D43DS29A4 C6D43DS29B4 C6D43DS29C4 C6D43DS29D4 C6D43DS29E4 C6D50DS29A4 C6D50DS29B4 C6D50DS29C4 C6D50DS29D4 C6D50DS29E4 40 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Card Edge Connectors Product Facts ■ ■ ■ ■ ■ ■ ■ Sizes from 6 to 65 dual positions. Contact mating surface optimizes reliability by concentrating the normal force in the actual contact area. Mounting ear options accommodate both Panel and PC Board attachment. Solder stand-offs facilitate cleaning. Bifurcated contact design provides redundant points of contact to maximize reliability. Tail lengths available to accommodate .062" [1.57] through .125" [3.18] thick PCB Boards and Wire Wrap termination. Straight or Right Angle contact configurations. Bifurcated contact design provides maximum reliability Description/Application The modified bellows card edge connectors are dual readout and are designed for reliable termination to double sided PCB boards. Modified Bellows The modified bellows card edge connector offers a variety of tail lengths for solder and wire wrap applications. Contacts are available in straight tail or right angle configurations to meet your individual purpose. The modified bellows line of connectors offers a variety of card slot depths and has optional high temperature plastic insulators. 41 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .100 x .200 [2.54 x 5.08], Straight Dip Solder And Wire Wrap Tails Product Facts .054 - .071 [1.37 - 1.80] P.C. Board Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .300 [7.62] Card Depth .610 [15.49] SECTION X-X ROTATED 90º J Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .200 [5.08] .025 [.64] Sq C D .100 [2.54] Ref. .368 [9.53] SECTION X-X Electrical Properties: E Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B Dim E .128 [3.25] Dia. Related Product Data: .200 [5.08] Polarization Key—page 57 .100 .100 [2.54] Daughter Card Edge Pattern— page 57 P=.040 [1.02] Dip Solder Applications P=.042 [1.07] For Wire Wrap Applications Mounting Styles .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 42 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Dimensions A B Mounting Ear Options C D E Tail Length .160" [4.06] (DIM “J”) 1.835 1.575 10 46.61 40.01 2.035 1.775 12 51.69 45.09 2 . 3 3 5 2 .075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3.035 2.775 22 77.09 70.49 3 . 3 3 5 3 .075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3.935 3.675 31 99.95 93.35 4 . 3 3 5 4 .075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 5.235 4.975 44 132.97 126.37 5.835 5.575 50 148.21 141.61 6.835 6.575 60 173.61 167.01 7.335 7.075 65 186.31 179.71 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 4.660 118.36 5.260 133.60 6.260 159.00 6.760 171.70 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Tail Length .220" [5.59] (DIM “J”) 1.835 1.575 10 46.61 40.01 2.035 1.775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3 . 0 3 5 2 .775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3 . 9 3 5 3 .675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A8D10DS29A2 A8D10DS29B2 A8D10DS29C2 A8D10DS29D2 A8D10DS29E2 A8D12DS29A2 A8D12DS29B2 A8D12DS29C2 — — A8D15DS29A2 A8D15DS29B2 A8D15DS29C2 A8D15DS29D2 A8D15DS29E2 A8D18DS29A2 A8D18DS29B2 A8D18DS29C2 A8D18DS29D2 A8D18DS29E2 A8D20DS29A2 A8D20DS29B2 A8D20DS29C2 – – A8D22DS29A2 A8D22DS29B2 A8D22DS29C2 – – A8D25DS29A2 A8D25DS29B2 A8D25DS29C2 A8D25DS29D2 A8D25DS29E2 A8D28DS29A2 A8D28DS29B2 A8D28DS29C2 – – A8D30DS29A2 A8D30DS29B2 A8D30DS29C2 A8D30DS29D2 A8D30DS29E2 A8D31DS29A2 A8D31DS29B2 A8D31DS29C2 A8D31DS29D2 A8D31DS29E2 A8D35DS29A2 A8D35DS29B2 A8D35DS29C2 – – A8D36DS29A2 A8D36DS29B2 A8D36DS29C2 – – A8D40DS29A2 A8D40DS29B2 A8D40DS29C2 – – A8D43DS29A2 A8D43DS29B2 A8D43DS29C2 – – A8D44DS29A2 A8D44DS29B2 A8D44DS29C2 – – A8D50DS29A2 A8D50DS29B2 A8D50DS29C2 A8D50DS29D2 A8D50DS29E2 A8D60DS29A2 A8D60DS29B2 A8D60DS29C2 – – A8D65DS29A2 A8D65DS29B2 A8D65DS29C2 A8D65DS29D2 A8D65DS29E2 A8D10DS29A3 A8D10DS29B3 A8D10DS29C3 A8D10DS29D3 A8D10DS29E3 A8D12DS29A3 A8D12DS29B3 A8D12DS29C3 – – A8D15DS29A3 A8D15DS29B3 A8D15DS29C3 A8D15DS29D3 A8D15DS29E3 A8D18DS29A3 A8D18DS29B3 A8D18DS29C3 A8D18DS29D3 A8D18DS29E3 A8D20DS29A3 A8D20DS29B3 A8D20DS29C3 – – A8D22DS29A3 A8D22DS29B3 A8D22DS29C3 – – A8D25DS29A3 A8D25DS29B3 A8D25DS29C3 A8D35DS29D3 A8D35DS29E3 A8D28DS29A3 A8D28DS29B3 A8D28DS29C3 – – A8D30DS29A3 A8D30DS29B3 A8D30DS29C3 A8D30DS29D3 A8D30DS29E3 A8D31DS29A3 A8D31DS29B3 A8D31DS29C3 A8D31DS29D3 A8D31DS29E3 A8D35DS29A3 A8D35DS29B3 A8D35DS29C3 – – A8D36DS29A3 A8D36DS29B3 A8D36DS29C3 – – A8D40DS29A3 A8D40DS29B3 A8D40DS29C3 – – A8D43DS29A3 A8D43DS29B3 A8D43DS29C3 – – 43 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Dimensions A B C Tail Length .220" [5.59] (DIM “J”) (Continued) 5.235 4.975 4.660 44 132.97 126.37 118.36 5.835 5.575 5.260 50 148.21 141.61 133.60 6.835 6.575 6.260 60 173.61 167.01 159.00 7.335 7.075 6.760 65 186.31 179.71 171.70 Mounting Ear Options D E 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Tail Length .560" [14.22] (DIM “J”) for Wire Wrap Termination 1.835 1.575 1.260 1.100 0.900 10 46.61 40.01 32.00 27.94 22.86 2.035 1.775 1.460 1.300 1.100 12 51.69 45.09 37.08 33.02 27.94 2.335 2.075 1.760 1.600 1.400 15 59.31 52.71 44.70 40.64 35.56 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 .700 18 66.93 60.33 52.32 48.26 43.18 2.835 2.575 2.260 2.100 1.900 20 72.01 65.41 57.40 53.34 48.26 3.035 2.775 2.460 2.300 2.100 22 77.09 70.49 62.48 58.42 53.34 3.335 3.075 2.760 2.600 2.400 25 84.71 78.11 70.10 66.04 60.96 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 .700 28 92.33 85.73 77.72 73.66 68.58 3.835 3.575 3.260 3.100 2.900 30 97.41 90.81 82.80 78.74 73.66 3.935 3.675 3.360 3.200 3.100 31 99.95 93.35 85.34 81.28 78.74 4.335 4.075 3.760 3.600 3.400 35 110.11 103.51 95.50 91.44 86.36 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 .500 36 112.65 106.05 98.04 93.98 88.90 4.835 4.575 4.260 4.100 3.900 40 122.81 116.21 108.20 104.14 99.06 5.135 4.875 4.560 4.400 4.200 43 130.43 123.83 115.82 111.76 106.68 5.235 4.975 4.660 4.500 4.300 44 132.97 126.37 118.36 114.30 109.22 5.835 5.575 5.260 5.100 4.800 50 148.21 141.61 133.60 129.54 121.92 6.835 6.575 6.260 6.100 5.900 60 173.61 167.01 159.00 154.94 149.86 7.335 7.075 6.760 6.600 6.400 65 186.31 179.71 171.70 167.64 162.56 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A8D44DS29A3 A8D44DS29B3 A8D44DS29C3 – – A8D50DS29A3 A8D50DS29B3 A8D50DS29C3 A8D50DS29D3 A8D50DS29E3 A8D60DS29A3 A8D60DS29B3 A8D60DS29C3 – – A8D65DS29A3 A8D65DS29B3 A8D65DS29C3 A8D65DS29D3 A8D65DS29E3 A8D10WW29A3 A8D10WW29B3 – – – A8D12WW29A3 A8D12WW29B3 – – – A8D15WW29A3 A8D15WW29B3 – – – A8D18WW29A3 A8D18WW29B3 – – – A8D20WW29A3 A8D20WW29B3 – – – A8D22WW29A3 A8D22WW29B3 – – – A8D25WW29A3 A8D25WW29B3 – – – A8D28WW29A3 A8D28WW29B3 – – – A8D30WW29A3 A8D30WW29B3 – – – A8D31WW29A3 A8D31WW29B3 – – – A8D35WW29A3 A8D35WW29B3 – – – A8D36WW29A3 A8D36WW29B3 – – – A8D40WW29A3 A8D40WW29B3 – – – A8D43WW29A3 A8D43WW29B3 – – – A8D44WW29A3 A8D44WW29B3 – – – A8D50WW29A3 A8D50WW29B3 – – – A8D60WW29A3 A8D60WW29B3 – – – A8D65WW29A3 A8D65WW29B3 – – – 44 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .100 x .200 [2.54 x 5.08] and .100 x .150 [2.54 x 3.81] Right Angle Dip Solder Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .14±.01 [3.56±.25] .025 Sq. Typ. [.64] H SECTION X-X ROTATED 90º Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .054±.071 [1.37±1.890] PC Board C D .100 Ref. [2.54] .368 [9.35] SECTION X-X Electrical Properties: E Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .128 [3.25] Dia. Dim E .040±.003 [1.02±.08] Dia. Related Product Data: Polarization Key—page 57 Daughter Card Edge Pattern— page 57 Dim G Dim K .100 .100 [2.54] Dim H Row to Row Spacing Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only .250 [6.35] Mounting Styles .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole .610 .610 [15.49] Ref. [15.49] Ref. No Mounting Ears .180 [4.57] Centered Mounting Ear .125 [3.18] Cross Drilled Hole .250 [6.35] Flush Mounting Ear .125 [3.18] Cross Drilled Hole 45 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions 10 12 15 18 20 22 25 28 30 31 35 36 40 43 44 50 60 65 Dimensions Mounting Ear Options A B C D E 1.835 46.61 2.035 51.69 2.335 59.31 2.635 66.93 2.835 72.01 3.035 77.09 3.335 84.71 3.635 92.33 3.835 97.41 3.935 99.95 4.335 110.11 4.435 112.65 4.835 122.81 5.135 130.43 5.235 132.97 5.835 148.21 6.835 173.61 7.335 186.31 1.575 40.01 1.775 45.09 2.075 52.71 2.375 60.33 2.575 65.41 2.775 70.49 3.075 78.11 3.375 85.73 3.575 90.81 3.675 93.35 4.075 103.51 4.175 106.05 4.575 116.21 4.875 123.83 4.975 126.37 5.575 141.61 6.575 167.01 7.075 179.71 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 4.660 118.36 5.260 133.60 6.260 159.00 6.760 171.70 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Centered Mounting Ear Only G 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 Flush Mounting Ear Only K 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole A8D10RA29A A8D10RA29C A8D10RA29E A8D10RA29F A8D12RA29A A8D12RA29C A8D12RA29E – A8D15RA29A A8D15RA29C A8D15RA29E A8D15RA29F A8D18RA29A A8D18RA29C A8D18RA29E A8D18RA29F A8D20RA29A A8D20RA29C A8D20RA29E – A8D22RA29A A8D22RA29C A8D22RA29E – A8D25RA29A A8D25RA29C A8D25RA29E A8D25RA29F A8D28RA29A A8D28RA29C A8D28RA29E – A8D30RA29A A8D30RA29C A8D30RA29E A8D30RA29F A8D31RA29A A8D31RA29C A8D31RA29E A8D31RA29F A8D35RA29A A8D35RA29C A8D35RA29E – A8D36RA29A A8D36RA29C A8D36RA29E – A8D40RA29A A8D40RA29C A8D40RA29E – A8D43RA29A A8D43RA29C A8D43RA29E – A8D44RA29A A8D44RA29C A8D44RA29E – A8D50RA29A A8D50RA29C A8D50RA29E A8D50RA29F A8D60RA29A A8D60RA29C A8D60RA29E – A8D65RA29A A8D65RA29C A8D65RA29E A8D65RA29F 46 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .150" [3.81] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions 10 12 15 18 20 22 25 28 30 31 35 36 40 43 44 50 60 65 Dimensions Mounting Ear Options A B C D E 1.835 46.61 2.035 51.69 2.335 59.31 2.635 66.93 2.835 72.01 3.035 77.09 3.335 84.71 3.635 92.33 3.835 97.41 3.935 99.95 4.335 110.11 4.435 112.65 4.835 122.81 5.135 130.43 5.235 132.97 5.835 148.21 6.835 173.61 7.335 186.31 1.575 40.01 1.775 45.09 2.075 52.71 2.375 60.33 2.575 65.41 2.775 70.49 3.075 78.11 3.375 85.73 3.575 90.81 3.675 93.35 4.075 103.51 4.175 106.05 4.575 116.21 4.875 123.83 4.975 126.37 5.575 141.61 6.575 167.01 7.075 179.71 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 4.660 118.36 5.260 133.60 6.260 159.00 6.760 171.70 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Centered Mounting Ear Only G 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 Flush Centered Mounting Mounting Ear Ear Only .125" [3.18] K Thru Hole 0.240 A8D10RA29AM233 6.10 0.240 A8D12RA29AM233 6.10 0.240 A8D15RA29AM233 6.10 0.240 A8D18RA29AM233 6.10 0.240 A8D20RA29AM233 6.10 0.240 A8D22RA29AM233 6.10 0.240 A8D25RA29AM233 6.10 0.240 A8D28RA29AM233 6.10 0.240 A8D30RA29AM233 6.10 0.240 A8D31RA29AM233 6.10 0.240 A8D35RA29AM233 6.10 0.240 A8D36RA29AM233 6.10 0.240 A8D40RA29AM233 6.10 0.240 A8D43RA29AM233 6.10 0.240 A8D44RA29AM233 6.10 0.240 A8D50RA29AM233 6.10 0.240 A8D60RA29AM233 6.10 0.240 A8D65RA29AM233 6.10 No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole A8D10RA29CM233 A8D10RA29EM233 A8D10RA29FM233 A8D12RA29CM233 A8D12RA29EM233 – A8D15RA29CM233 A8D15RA29EM233 A8D15RA29FM233 A8D18RA29CM233 A8D18RA29EM233 A8D18RA29FM233 A8D20RA29CM233 A8D20RA29EM233 – A8D22RA29CM233 A8D22RA29EM233 – A8D25RA29CM233 A8D25RA29EM233 A8D25RA29FM233 A8D28RA29CM233 A8D28RA29EM233 – A8D30RA29CM233 A8D30RA29EM233 A8D30RA29FM233 A8D31RA29CM233 A8D31RA29EM233 A8D31RA29FM233 A8D35RA29CM233 A8D35RA29EM233 – A8D36RA29CM233 A8D36RA29EM233 – A8D40RA29CM233 A8D40RA29EM233 – A8D43RA29CM233 A8D43RA29EM233 – A8D44RA29CM233 A8D44RA29EM233 – A8D50RA29CM233 A8D50RA29EM233 A8D50RA29FM233 A8D60RA29CM233 A8D60RA29EM233 – A8D65RA29CM233 A8D65RA29EM233 A8D65RA29FM233 47 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .125 x .250 [3.18 x 6.35], Centerline Straight Dip Solder and Wire Wrap Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .054±.071 [1.37±1.890] PC Board .300 [7.62] Card Depth .610 [5.49] Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum SECTION X-X ROTATED 90º J .250 [6.35] .025 Sq. [.64] C D .125 Ref. [3.18] .368 [9.35] SECTION X-X Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms E B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B P .128 [3.25] Dia. ±.003 Dia. [±.080] Dim E Related Product Data: .250 [6.35] Polarization Key—page 57 Daughter Card Edge Pattern— page 57 .125 [3.18] P=.040 [1.02] Dip Solder Applications P=.042 [1.07] For Wire Wrap Applications Mounting Styles .250 [6.35] .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 48 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row Dip Solder No. of Dual Readout Positions Mounting Ear Options Dimensions A B Tail Length .160" [4.06] (DIM “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2 . 6 8 0 2 .420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4 . 3 0 5 4 .045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 C D E 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A7D06DS29A2 A7D06DS29B2 A7D06DS29C2 A7D06DS29D2 A7D06DS29E2 A7D10DS29A2 A7D10DS29B2 A7D10DS29C2 A7D10DS29D2 A7D10DS29E2 A7D15DS29A2 A7D15DS29B2 A7D15DS29C2 A7D15DS29D2 A7D15DS29E2 A7D18DS29A2 A7D18DS29B2 A7D18DS29C2 A7D18DS29D2 A7D18DS29E2 A7D22DS29A2 A7D22DS29B2 A7D22DS29C2 – – A7D25DS29A2 A7D25DS29B2 A7D25DS29C2 A7D25DS29D2 A7D25DS29E2 A7D28DS29A2 A7D28DS29B2 A7D28DS29C2 – – A7D30DS29A2 A7D30DS29B2 A7D30DS29C2 A7D30DS29D2 A7D30DS29E2 A7D35DS29A2 A7D35DS29B2 A7D35DS29C2 – – A7D36DS29A2 A7D36DS29B2 A7D36DS29C2 – – A7D40DS29A2 A7D40DS29B2 A7D40DS29C2 – – A7D43DS29A2 A7D43DS29B2 A7D43DS29C2 – – A7D50DS29A2 A7D50DS29B2 A7D50DS29C2 A7D50DS29D2 A7D50DS29E2 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A7D06WW29A3 A7D06WW29B3 – – – A7D10WW29A3 A7D10WW29B3 – – – A7D15WW29A3 A7D15WW29B3 – – – A7D18WW29A3 A7D18WW29B3 – – – A7D22WW29A3 A7D22WW29B3 – – – A7D25WW29A3 A7D25WW29B3 – – – A7D28WW29A3 A7D28WW29B3 – – – A7D30WW29A3 A7D30WW29B3 – – – A7D35WW29A3 A7D35WW29B3 – – – A7D36WW29A3 A7D36WW29B3 – – – A7D40WW29A3 A7D40WW29B3 – – – A7D43WW29A3 A7D43WW29B3 – – – A7D50WW29A3 A7D50WW29B3 – – – .125" [3.18] Centerline / .250" [6.35] Row-to-Row Wire Wrap No. of Dual Readout Positions Mounting Ear Options Dimensions A B Tail Length .560" [14.22] (DIM “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2.680 2.420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3 . 5 5 5 3 .295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4.305 4.045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 C D E 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 49 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .125 x .250 [3.18 x 6.35], .125 x .150 [3.18 x 3.81], .125 x .200 [3.18 x 5.08] Centerline, Right Angle Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .14±.01 [3.56±.25] .025 Sq. Typ. [.64] H Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .054±.071 [1.37±1.890] PC Board SECTION X-X ROTATED 90º C D .125 REF [3.18] .368 [9.35] SECTION X-X Electrical Properties: E Operation Voltage—1000 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .128 [3.25] Dia. Dim E .040±.003 [1.02±.08] Dia. Related Product Data: Polarization Key—page 57 Dim H Row to Row Spacing .125 [3.18] Dim G Dim K Daughter Card Edge Pattern— page 57 Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only Mounting Styles .250 [6.35] .250 [6.35] .610 [15.49] Ref. .180 Centered Mounting Ear [4.57] .125 [3.18] Thru Hole .610 [15.49] Ref. No Mounting Ears .610 [15.49] Ref. Centered Mounting Ear .180 .125 [3.18] Thru Hole [4.57] .250 [6.35] Flush Mounting Ear .125 [3.18] Cross Drilled Hole 50 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions Dimensions Mounting Ear Options D E Centered Mounting Ear Only G 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 A7D06RA29AM231 A7D06RA29CM231 A7D06RA29EM231 A7D06RA29FM231 A7D10RA29AM231 A7D10RA29CM231 A7D10RA29EM231 A7D10RA29FM231 A7D15RA29AM231 A7D15RA29CM231 A7D15RA29EM231 A7D15RA29FM231 A7D18RA29AM231 A7D18RA29CM231 A7D18RA29EM231 A7D18RA29FM231 A7D22RA29AM231 A7D22RA29CM231 A7D22RA29EM231 A7D22RA29FM231 A7D25RA29AM231 A7D25RA29CM231 A7D25RA29EM231 A7D25RA29FM231 A7D28RA29AM231 A7D28RA29CM231 A7D28RA29EM231 A7D28RA29FM231 A7D30RA29AM231 A7D30RA29CM231 A7D30RA29EM231 A7D30RA29FM231 A7D35RA29AM231 A7D35RA29CM231 A7D35RA29EM231 A7D35RA29FM231 A7D36RA29AM231 A7D36RA29CM231 A7D36RA29EM231 A7D36RA29FM231 A7D40RA29AM231 A7D40RA29CM231 A7D40RA29EM231 A7D40RA29FM231 A7D43RA29AM231 A7D43RA29CM231 A7D43RA29EM231 A7D43RA29FM231 A7D50RA29AM231 A7D50RA29CM231 A7D50RA29EM231 A7D50RA29FM231 .200" [5.08] Row-to-Row (Dim. “H”) Spacing 1.555 1.295 1.035 0.875 6 39.50 32.89 26.29 22.23 2.055 1.795 1.535 1.375 10 52.20 45.59 38.99 34.93 2.680 2.420 2.160 2.000 15 68.07 61.47 54.86 50.80 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 .375 18 77.60 70.99 64.39 60.33 3.555 3.295 3.035 2.875 22 90.30 83.69 77.09 73.03 3.930 3.670 3.410 3.250 25 99.82 93.22 86.61 82.55 4.305 4.045 3.785 3.625 28 109.35 102.74 96.14 92.08 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 .875 30 115.70 109.09 102.49 98.43 5.180 4.920 4.660 4.500 35 131.57 124.97 118.36 114.30 5.305 5.045 4.785 4.625 36 134.75 128.14 121.54 117.48 5.805 5.545 5.285 5.125 40 147.45 140.84 134.24 130.18 6.180 5.920 5.660 5.500 43 156.97 150.37 143.76 139.70 7.055 6.795 6.535 6.375 50 179.20 172.59 165.99 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 A7D06RA29AM232 A7D06RA29CM232 A7D06RA29EM232 A7D06RA29FM232 A7D10RA29AM232 A7D10RA29CM232 A7D10RA29EM232 A7D10RA29FM232 A7D15RA29AM232 A7D15RA29CM232 A7D15RA29EM232 A7D15RA29FM232 A7D18RA29AM232 A7D18RA29CM232 A7D18RA29EM232 A7D18RA29FM232 A7D22RA29AM232 A7D22RA29CM232 A7D22RA29EM232 A7D22RA29FM232 A7D25RA29AM232 A7D25RA29CM232 A7D25RA29EM232 A7D25RA29FM232 A7D28RA29AM232 A7D28RA29CM232 A7D28RA29EM232 A7D28RA29FM232 A7D30RA29AM232 A7D30RA29CM232 A7D30RA29EM232 A7D30RA29FM232 A7D35RA29AM232 A7D35RA29CM232 A7D35RA29EM232 A7D35RA29FM232 A7D36RA29AM232 A7D36RA29CM232 A7D36RA29EM232 A7D36RA29FM232 A7D40RA29AM232 A7D40RA29CM232 A7D40RA29EM232 A7D40RA29FM232 A7D43RA29AM232 A7D43RA29CM232 A7D43RA29EM232 A7D43RA29FM232 A7D50RA29AM232 A7D50RA29CM232 A7D50RA29EM232 A7D50RA29FM232 A B C .150" [3.81] Row-to-Row (Dim. “H”) Spacing 1.555 1.295 1.035 6 39.50 32.89 26.29 2.055 1.795 1.535 10 52.20 45.59 38.99 2.680 2.420 2.160 15 68.07 61.47 54.86 3 . 0 5 5 2 . 7 9 5 2 .535 18 77.60 70.99 64.39 3.555 3.295 3.035 22 90.30 83.69 77.09 3.930 3.670 3.410 25 99.82 93.22 86.61 4.305 4.045 3.785 28 109.35 102.74 96.14 4 . 5 5 5 4 . 2 9 5 4 .035 30 115.70 109.09 102.49 5.180 4.920 4.660 35 131.57 124.97 118.36 5.305 5.045 4.785 36 134.75 128.14 121.54 5.805 5.545 5.285 40 147.45 140.84 134.24 6.180 5.920 5.660 43 156.97 150.37 143.76 7.055 6.795 6.535 50 179.20 172.59 165.99 Flush Mounting Ear Only K Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole 51 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions Dimensions A B C Mounting Ear Options E Centered Mounting Ear Only G Flush Mounting Ear Only K Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 A7D06RA29A A7D06RA29C A7D06RA29E A7D06RA29F A7D10RA29A A7D10RA29C A7D10RA29E A7D10RA29F A7D15RA29A A7D15RA29C A7D15RA29E A7D15RA29F A7D18RA29A A7D18RA29C A7D18RA29E A7D18RA29F A7D22RA29A A7D22RA29C A7D22RA29E A7D22RA29F A7D25RA29A A7D25RA29C A7D25RA29E A7D25RA29F A7D28RA29A A7D28RA29C A7D28RA29E A7D28RA29F A7D30RA29A A7D30RA29C A7D30RA29E A7D30RA29F A7D35RA29A A7D35RA29C A7D35RA29E A7D35RA29F A7D36RA29A A7D36RA29C A7D36RA29E A7D36RA29F A7D40RA29A A7D40RA29C A7D40RA29E A7D40RA29F A7D43RA29A A7D43RA29C A7D43RA29E A7D43RA29F A7D50RA29A A7D50RA29C A7D50RA29E A7D50RA29F D .250" [6.35] Row-to-Row (Dim. “H”) Spacing 1.555 1.295 1.035 0.875 6 39.50 32.89 26.29 22.23 2.055 1.795 1.535 1.375 10 52.20 45.59 38.99 34.93 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 .000 15 68.07 61.47 54.86 50.80 3.055 2.795 2.535 2.375 18 77.60 70.99 64.39 60.33 3.555 3.295 3.035 2.875 22 90.30 83.69 77.09 73.03 3.930 3.670 3.410 3.250 25 99.82 93.22 86.61 82.55 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 .625 28 109.35 102.74 96.14 92.08 4.555 4.295 4.035 3.875 30 115.70 109.09 102.49 98.43 5.180 4.920 4.660 4.500 35 131.57 124.97 118.36 114.30 5.305 5.045 4.785 4.625 36 134.75 128.14 121.54 117.48 5.805 5.545 5.285 5.125 40 147.45 140.84 134.24 130.18 6.180 5.920 5.660 5.500 43 156.97 150.37 143.76 139.70 7.055 6.795 6.535 6.375 50 179.20 172.59 165.99 161.93 Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole 52 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors, .156 x .200 [3.96 x 5.08] Centerline, Straight Dip Solder and Wire Wrap Tails Product Facts .054±.071 [1.37±1.890 ] PC Board Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .300 [7.62] Card Depth .610 [5.49] SECTION X-X ROTATED 90º J Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .200 [5.08] .025 Sq. [.64] C D .156 Ref. [3.96] .368 [9.35] SECTION X-X Electrical Properties: E Operation Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B Dim E P±.003 [.08] Dia. .128 [3.25] Dia. Related Product Data: .200 [5.08] Polarization Key—page 57 .156 [3.25] Daughter Card Edge Pattern— page 57 P=.040 [1.02] Dip Solder Applications P=.042 [1.07] For Wire Wrap Applications Mounting Styles .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears 53 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Mounting Ear Options Dimensions A B C D E Tail Length .160" [4.06] (DIM “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3.188 2.938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 4.280 4.030 22 108.71 102.36 4.748 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 6.464 6.214 36 164.19 157.84 7.556 7.306 43 191.92 185.57 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.717 94.41 4.185 106.30 4.653 118.19 5.901 149.89 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.596 91.34 4.064 103.23 4.532 115.11 5.780 146.81 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 3.276 83.21 3.744 95.10 4.212 106.98 5.460 138.68 6.552 166.42 Tail Length .220" [5.59] (DIM “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3.188 2.938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 4.280 4.030 22 108.71 102.36 4.748 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 6.464 6.214 36 164.19 157.84 7.556 7.306 43 191.92 185.57 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.717 94.41 4.185 106.30 4.653 118.19 5.901 149.89 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.596 91.34 4.064 103.23 4.532 115.11 5.780 146.81 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 3.276 83.21 3.744 95.10 4.212 106.98 5.460 138.68 6.552 166.42 Tail Length .560" [14.22] (DIM “J”) For Wire Wrap Termination 1.784 1.534 1.221 1.100 6 45.31 38.96 31.01 27.94 2.408 2.158 1.845 1.724 10 61.16 54.81 46.86 43.79 2.720 2.470 2.157 2.036 12 69.09 62.74 54.79 51.71 3.188 2.938 2.625 2.504 15 80.98 74.63 66.68 63.60 3.656 3.406 3.093 2.972 18 92.86 86.51 78.56 75.49 4.280 4.030 3.717 3.596 22 108.71 102.36 94.41 91.34 4.748 4.498 4.185 4.064 25 120.60 114.25 106.30 103.23 5.216 4.966 4.653 4.532 28 132.49 126.14 118.19 115.11 6.464 6.214 5.901 5.780 36 164.19 157.84 149.89 146.81 7.556 7.306 6.993 6.872 43 191.92 185.57 177.62 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 3.276 83.21 3.744 95.10 4.212 106.98 5.460 138.68 6.552 166.42 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears A6D06DS29A2 A6D06DS29B2 A6D06DS29C2 A6D10DS29A2 A6D10DS29B2 A6D10DS29C2 A6D12DS29A2 A6D12DS29B2 A6D12DS29C2 A6D15DS29A2 A6D15DS29B2 A6D15DS29C2 A6D18DS29A2 A6D18DS29B2 A6D18DS29C2 A6D22DS29A2 A6D22DS29B2 A6D22DS29C2 A6D25DS29A2 A6D25DS29B2 A6D25DS29C2 A6D28DS29A2 A6D28DS29B2 A6D28DS29C2 A6D36DS29A2 A6D36DS29B2 A6D36DS29C2 A6D43DS29A2 A6D43DS29B2 A6D43DS29C2 A6D06DS29A3 A6D06DS29B3 A6D06DS29C3 A6D10DS29A3 A6D10DS29B3 A6D10DS29C3 A6D12DS29A3 A6D12DS29B3 A6D12DS29C3 A6D15DS29A3 A6D15DS29B3 A6D15DS29C3 A6D18DS29A3 A6D18DS29B3 A6D18DS29C3 A6D22DS29A3 A6D22DS29B3 A6D22DS29C3 A6D25DS29A3 A6D25DS29B3 A6D25DS29C3 A6D28DS29A3 A6D28DS29B3 A6D28DS29C3 A6D36DS29A3 A6D36DS29B3 A6D36DS29C3 A6D43DS29A3 A6D43DS29B3 A6D43DS29C3 A6D06WW29A3 A6D06WW29B3 – A6D10WW29A3 A6D10WW29B3 – A6D12WW29A3 A6D12WW29B3 – A6D15WW29A3 A6D15WW29B3 – A6D18WW29A3 A6D18WW29B3 – A6D22WW29A3 A6D22WW29B3 – A6D25WW29A3 A6D25WW29B3 – A6D28WW29A3 A6D28WW29B3 – A6D36WW29A3 A6D36WW29B3 – A6D43WW29A3 A6D43WW29B3 – 54 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .156 x .200 [3.96 x 5.08] Centerline, .156 x .150 [3.96 x 3.81], Right Angle, Dip Solder Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .14±.01 [3.56±.25] .025 Sq. Typ. [.64] H Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .054±.071 [1.37±1.890] PC Board SECTION X-X ROTATED 90º C D .156 REF [3.96] .368 [9.35] SECTION X-X Electrical Properties: Operation Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance—10 milliohms E B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .128 [3.25] Dia. Dim E .040±.003 [1.02±.08] Dia. Related Product Data: Polarization Key—page 57 Daughter Card Edge Pattern— page 57 Dim G Dim K Dim H Row to Row Spacing .156 [3.96] Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only Mounting Styles .250 [6.35] .250 [6.35] .610 [15.49] Ref. .180 Centered Mounting Ear [4.57] .125 [3.18] Thru Hole Catalog 1654080 Issued 7-03 www.tycoelectronics.com .610 [15.49] Ref. No Mounting Ears Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. .610 [15.49] Ref. Centered Mounting Ear .125 [3.18] Thru Hole Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 Flush Mounting Ear .125 [3.18] Cross Drilled Hole South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 55 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions Dimensions A B C Mounting Ear Options D E Centered Mounting Ear Only G Flush Mounting Ear Only K Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole .200" [5.08] Row-to-Row (Dim. “H”) Spacing 6 1.784 45.31 1.534 38.96 1.221 31.01 1.100 27.94 0.780 19.81 0.470 11.94 0.290 7.37 A6D06RA29A A6D06RA29C A6D06RA29E A6D06RA29F 10 2.408 61.16 2.158 54.81 1.845 46.86 1.724 43.79 1.404 35.66 0.470 11.94 0.290 7.37 A6D10RA29A A6D10RA29C A6D10RA29E A6D10RA29F 12 2.720 69.09 2.470 62.74 2.157 54.79 2.036 51.71 1.716 43.59 0.470 11.94 0.290 7.37 A6D12RA29A A6D12RA29C A6D12RA29E A6D12RA29F 15 3.188 80.98 2.938 74.63 2.625 66.68 2.504 63.60 2.184 55.47 0.470 11.94 0.290 7.37 A6D15RA29A A6D15RA29C A6D15RA29E A6D15RA29F 18 3.656 92.86 3.406 86.51 3.093 78.56 2.972 75.49 2.652 67.36 0.470 11.94 0.290 7.37 A6D18RA29A A6D18RA29C A6D18RA29E A6D18RA29F 22 4.280 108.71 4.030 102.36 3.717 94.41 3.596 91.34 3.276 83.21 0.470 11.94 0.290 7.37 A6D22RA29A A6D22RA29C A6D22RA29E A6D22RA29F 25 4.748 120.60 4.498 114.25 4.185 106.30 4.064 103.23 3.744 95.10 0.470 11.94 0.290 7.37 A6D25RA29A A6D25RA29C A6D25RA29E A6D25RA29F 28 5.216 132.49 4.966 126.14 4.653 118.19 4.532 115.11 4.212 106.98 0.470 11.94 0.290 7.37 A6D28RA29A A6D28RA29C A6D28RA29E A6D28RA29F 36 6.464 164.19 6.214 157.84 5.901 149.89 5.780 146.81 5.460 138.68 0.470 11.94 0.290 7.37 A6D36RA29A A6D36RA29C A6D36RA29E A6D36RA29F 40 7.088 180.04 6.838 173.69 6.525 165.74 6.404 213.46 6.084 154.53 0.470 11.94 0.290 7.37 A6D40RA29A A6D40RA29C A6D40RA29E A6D40RA29F 43 7.556 191.92 7.306 185.57 6.993 177.62 6.872 174.55 6.552 166.42 0.470 11.94 0.290 7.37 A6D43RA29A A6D43RA29C A6D43RA29E A6D43RA29F .150" [3.81] Row-to-Row (Dim. “H”) Spacing 6 1.784 45.31 1.534 38.96 1.221 31.01 1.100 27.94 0.780 19.81 0.420 10.67 0.240 6.10 A6D06RA29AM233 A6D06RA29CM233 A6D06RA29EM233 A6D06RA29FM233 10 2.408 61.16 2.158 54.81 1.845 46.86 1.724 43.79 1.404 35.66 0.420 10.67 0.240 6.10 A6D10RA29AM233 A6D10RA29CM233 A6D10RA29EM233 A6D10RA29FM233 12 2.720 69.09 2.470 62.74 2.157 54.79 2.036 51.71 1.716 43.59 0.420 10.67 0.240 6.10 A6D12RA29AM233 A6D12RA29CM233 A6D12RA29EM233 A6D12RA29FM233 15 3.188 80.98 2.938 74.63 2.625 66.68 2.504 63.60 2.184 55.47 0.420 10.67 0.240 6.10 A6D15RA29AM233 A6D15RA29CM233 A6D15RA29EM233 A6D15RA29FM233 18 3.656 92.86 3.406 86.51 3.093 78.56 2.972 75.49 2.652 67.36 0.420 10.67 0.240 6.10 A6D18RA29AM233 A6D18RA29CM233 A6D18RA29EM233 A6D18RA29FM233 22 4.280 108.71 4.030 102.36 3.717 94.41 3.596 91.34 3.276 83.21 0.420 10.67 0.240 6.10 A6D22RA29AM233 A6D22RA29CM233 A6D22RA29EM233 A6D22RA29FM233 25 4.748 120.60 4.498 114.25 4.185 106.30 4.064 103.23 3.744 95.10 0.420 10.67 0.240 6.10 A6D25RA29AM233 A6D25RA29CM233 A6D25RA29EM233 A6D25RA29FM233 28 5.216 132.49 4.966 126.14 4.653 118.19 4.532 115.11 4.212 106.98 0.420 10.67 0.240 6.10 A6D28RA29AM233 A6D28RA29CM233 A6D28RA29EM233 A6D28RA29FM233 36 6.464 164.19 6.214 157.84 5.901 149.89 5.780 146.81 5.460 138.68 0.420 10.67 0.240 6.10 A6D36RA29AM233 A6D36RA29CM233 A6D36RA29EM233 A6D36RA29FM233 40 7.088 180.04 6.838 173.69 6.525 165.74 6.404 162.66 6.084 154.53 0.420 10.67 0.240 6.10 A6D40RA29AM233 A6D40RA29CM233 A6D40RA29EM233 A6D40RA29FM233 43 7.556 191.92 7.306 185.57 6.993 177.62 6.872 174.55 6.552 166.42 0.420 10.67 0.240 6.10 A6D43RA29AM233 A6D43RA29CM233 A6D43RA29EM233 A6D43RA29FM233 56 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Card Edge Polarization Keys Description/Application Tyco Electronics can provide polarization keys in the basic configuration shown on this page. Our Modified Bellows and Cantilever Beam Series Card Edge Connectors use these keys. The part number and the connector series for which it was designed are listed in the table below. Break Off Point 45° .24 [6.10] .033 [.84] .19 [4.83] Ordering Information Acquired Part Number 98014-01 98014-01 Used on Connector Series Modified Bellows Cantilever Beam Shown on Pages 41-56 28-40 Card Edge Connectors Recommended Daughter Card Edge Pattern Per MIL-C-21097E .062 [1.57] Board Thickness 30° Slot Depth Min. Contact Spacing Dim. B Dim. A (Per Applicable Catalog Page) .015 [.38] See Note 3 Daughter Card Contact Spacing Non-Accum. .100 [2.54] .125 [3.18] .156 [3.96] Dim A ±.005 (.13) .093 [2.36] .093 [2.36] .105* [2.67] Dim B .052 [1.32] .052 [1.32] .094 [2.39] * Except MIL-C-21097E 8–4 which is .070 [1.78] NOTES: 1. Dimensions are in inches 2. Unless otherwise specified, tolerance is ±.005 [0.13 mm] for three place decimals. 3. Number of contact fingers shall be the same as the corresponding printed wiring connector. 57 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors Product Facts ■ Low profile housing is .460 [11.68] deep ■ 6 through 43 dual positions on .156 [3.96] centerline; 6 though 50 dual positions on .125 [3.18] centerline ■ Solder eyelet for wire-toboard or solder post for mother-daughter board application ■ Selective gold plating of contact area for high performance at low cost ■ Alternate platings are available on request ■ Contacts bifurcated for redundancy ■ Tin plate for high solderability of solder eyelets and posts ■ Accepts .055-.070 [1.401.78] thick printed circuit boards ■ Housings available with or without mounting ears ■ Intercontact keying available ■ UL 94V-0 rated, glass-filled polyester housings ■ Variety of solder post lengths ■ 5 ampere current rating per contact* ■ Recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 For printed circuit board packaging, AMP Low Profile Edge Connectors provide high performance, low cost connections on .125 [3.18] and .156 [3.96] centerline spacings. .100 [2.54] centerline connectors can be made available, consult Tyco Electronics. with either solder posts for mother-daughter board applications or solder eyelet contacts for wire-toboard use. Mounted connector housings extend only .460 [11.68] from the mother board to allow efficient use of available space. Low Profile Edge Connectors feature clear slot entry and accept .055-.070 [1.40-1.78] thick doublesided printed circuit boards. Solder posts are available with .150 [3.18] and .180 [4.57] long tails on .140 [3.56] or .200 [5.08] rowto-row spacing. These low profile connectors are available in 6 through 43 dual position sizes on .156 [3.96] centerline spacing and with 6 through 50 dual positions on .125 [3.18] centers. Connectors are supplied Impact-resistant thermoplastic housing, UL rated 94V-0, have molded-in cavity identification and are available with or without mounting ears. Additional features of the housings include intercontact keying provisions, probe slots and identification of number one position. The precision formed contacts made of phosphor bronze are gold plated on the contact mating surface only. This selective plating provides high reliability while maintaining low cost. Solder eyelets and posts are tin plated for excellent solderability. The contact is bifurcated for redundancy. Shorting contacts are available. All connector configurations are furnished preloaded. Selectively loaded connectors can be made available for added economy. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 58 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .125 [3.18] Centerline Material and Finish: .128 Dia. [3.25] 2 (Plcs.) PCBoard Thickness— .055-.070 [1.40-1.78] Housing—Green, glass-filled polyester Contacts—Phosphor bronze, duplex plated .000030 [0.00076] gold in contact area; .000100 [0.00254] bright tin on posts, with entire contact underplated .000030 [0.00076] nickel .300 C [7.62] .125 [3.18] .150 [3.81] .125 Typ. [3.18] A Related Product Data: Keying Plug—page 63 PC Board Hole Layouts—See below PC Board Edge Pattern—page 63 B D .460 [11.68] Technical Documents: (pages 186, 187): .250 [6.35] Product Specification 108-9044 Instruction Sheet 408-7772 .125 Typ. [3.18] #1 Cavity Identification Molded Characters (Upper and Lower Case Letters Omitting Letters G, I, O &Q) 1 2 3 4 5 6 A B C D E F E .295 [7.49] .125 Ref. [3.18] .295 [7.49] .125 Ref. [3.18] .295 [7.49] .165 [4.19] .165 [4.19] .165 [4.19] Post Length (See Chart) Post Length (See Chart) .200 [5.08] .335 [8.51] Typ. .125 [3.18] B .235 Ref. [5.97] Flow Solder Post .140 [3.56] Row-to-Row Spacing .200 .052 Dia. [5.08] [1.32] .128 Dia. [3.25] .280 Ref. [7.11] .140 [3.56] Flow Solder Post .200 [5.08] Row-to-Row Spacing .100 [2.54] Recommended PC Board Hole Layout Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing .140 .052 Dia. [3.56] [1.32] .128 Dia. [3.25] .335 [8.51] Typ. .125 Ref. [3.18] .125 [3.18] B .070 [1.78] Recommended PC Board Hole Layout 59 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .125 [3.18] Centerline (Continued) Flow Solder Post .200 [5.08] Row-to-Row Spacing No. of Dual Positions A B Dimensions C D E Post Length* With Mounting Ears Without Mounting Ears 6 .875 22.23 — .370 9.40 1.035 26.29 — .150 — 2-530671-1 10 1.375 34.93 1.795 45.59 .370 9.40 1.535 38.99 2.055 52.20 .150 .180 — 2-530663-2 2-530671-2 — 15 2.420 61.47 2.795 70.99 3.295 83.69 — 2-530671-3 .180 2-530663-4 2-530671-4 .150 2-530662-5 2-530671-5 — .150 — 3-530671-3 4.305 109.35 .150 2-530662-6 2-530671-6 — .150 — 2-530671-7 5.045 128.14 5.545 140.84 6.795 172.59 2.160 54.86 2.535 64.39 3.035 77.09 3.285 83.44 3.785 96.14 4.035 102.49 4.785 121.54 5.285 134.24 6.535 165.99 .150 4.045 102.74 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .437 11.10 .437 11.10 2.680 68.07 3.055 77.60 3.555 90.30 5.305 134.75 5.805 147.45 7.055 179.20 .150 .180 — — 2-530671-9 2-530672-9 .150 — 3-530671-0 50 2.000 50.80 2.375 60.33 2.875 73.03 3.125 79.38 3.625 92.08 3.875 98.43 4.625 117.48 5.125 130.18 6.375 161.93 .150 3-530662-2 — No. of Dual Positions A B Dimensions C D E Post Length* With Mounting Ears Without Mounting Ears 15 2.000 50.80 — .370 9.40 2.160 54.86 — .150 — 2-530673-3 .370 9.40 .437 11.10 3.785 96.14 6.535 165.99 — .150 .180 — 2-530674-6 2-530673-6 — 7.055 179.20 .180 3-530659-2 — 18 22 24 28 30 36 40 Flow Solder Post .140 [3.56] Row-to-Row Spacing 3.625 92.08 6.375 161.93 28 50 Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing No. of Dual Positions 15 22 28 40 50 — — — 6.795 172.59 With Mounting Ears A B Dimensions C D E 2.000 50.80 2.875 73.02 3.625 92.08 5.125 130.17 6.375 161.92 2.420 61.47 3.295 83.69 4.045 102.74 5.545 140.84 6.795 172.59 .370 9.40 .370 9.40 .370 9.40 .437 11.10 .437 11.10 2.160 54.86 3.035 77.08 3.785 96.14 5.285 134.23 6.535 165.98 2.680 68.07 3.555 90.29 4.305 109.35 5.805 147.44 7.055 179.19 2-530664-3 2-530664-5 2-530664-6 3-530664-0 3-530664-2 *Metric equivalents for post length are .150 = [3.81]; .180 = [4.57]. Note: Other connector sizes can be made available, consult Tyco Electronics. 60 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .156 [3.96] Centerline Material and Finish: Mounting Ear with Insert Housing—Green, glass-filled polyester Contacts—Phosphor bronze, duplex plated .000030 [0.00076] gold in contact area; .000100 [0.00254] bright tin on posts, with entire contact underplated .000030 [0.00076] nickel Insert—Brass .128 Dia. [3.25] (2 Plcs.) PCBoard Thickness— .055-.070 [1.40-1.78] .300 [7.62] C .160 [4.06] Threaded Inserts 4-40 NC-2B (2 per connector) Related Product Data: Keying Plug—page 63 PC Board Hole Layouts—See below PC Board Edge Pattern—page 63 .156 Typ. [3.96] A .150 [3.81] B D .460 [11.68] Technical Documents: (pages 186, 187): .250 [6.35] Product Specification 108-9044 Instruction Sheet 408-7772 .156 Typ. [3.96] #1 Cavity Identification Molded Characters (Upper and Lower Case Letters Omitting Letters G, I, O &Q) 1 2 3 4 5 6 A B C D E F E .295 [7.49] .125 Ref. [3.18] .295 [7.49] .125 Ref. [3.18] .295 [7.49] .165 [4.19] .165 [4.19] .165 [4.19] Post Length (See Chart) Post Length (See Chart) .200 [5.08] .156 [3.96] B .235 Ref. [5.97] Flow Solder Post .140 [3.56] Row-to-Row Spacing .200 .052 Dia. [5.08] [1.32] .128 Dia. [3.25] .378 [9.59] Typ. .280 Ref. [7.11] .140 [3.56] Flow Solder Post .200 [5.08] Row-to-Row Spacing .100 [2.54] Recommended PC Board Hole Layout Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing .140 .052 Dia. [3.56] [1.32] .128 Dia. [3.25] .378 [9.59] Typ. .125 Ref. [3.18] .156 [3.96] B .070 [1.78] Recommended PC Board Hole Layout 61 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .156 [3.96] Centerline (Continued) Flow Solder Post .200 [5.08] Row-to-Row Spacing Flow Solder Post .140 [3.56] Row-to-Row Spacing and Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing No. of Dual Positions A B 6 1.100 27.94 1.535 38.99 .370 9.40 10 1.724 43.79 2.159 54.84 12 2.036 51.71 2.471 62.76 Dimensions C D E Post Length* 1.240 31.50 1.785 45.34 .150 .370 9.40 1.864 47.35 2.409 61.19 .150 .180 .370 9.40 2.176 55.27 2.721 69.11 .150 15 2.504 63.60 2.939 74.65 .370 9.40 2.644 67.16 3.189 81.00 .150 18 2.972 75.49 3.407 86.54 .370 9.40 3.112 79.04 3.657 92.89 .150 .180 22 3.596 91.34 4.031 102.39 .370 9.40 3.736 94.89 4.281 108.74 .150 25 4.064 103.23 4.499 114.27 .370 9.40 4.204 106.78 4.749 120.62 28 4.532 115.11 4.967 126.16 .370 9.40 4.672 118.67 5.217 132.51 30 4.844 123.04 5.279 134.09 .437 11.10 4.984 126.59 5.529 140.44 36 5.780 146.18 6.215 157.86 .437 11.10 5.920 150.37 6.465 164.21 43 6.872 174.55 7.307 185.60 .437 11.10 7.012 178.10 7.557 191.95 E Post Length* No. of Dual Positions 6 10 15 18 22 24 28 30 36 43 A 1.100 27.94 1.724 43.79 2.504 63.60 2.972 75.49 3.596 91.34 3.908 99.26 4.532 115.11 4.844 123.04 5.780 146.81 6.872 174.55 Dimensions B C D 1.535 .370 1.240 1.785 38.99 9.40 31.50 45.34 2.159 .370 1.864 2.409 54.84 9.40 47.35 61.19 2.939 .370 2.644 3.189 74.65 9.40 67.16 81.00 3.407 .370 3.112 3.657 86.54 9.40 79.04 92.89 4.031 .370 3.736 4.281 102.39 9.40 94.89 108.74 4.343 .370 4.048 4.593 110.31 9.40 102.81 116.66 4.967 .370 4.672 5.217 126.16 9.40 118.67 132.51 5.279 .437 4.984 5.529 134.09 11.10 126.59 140.44 6.215 .437 5.920 6.465 155.58 11.10 150.36 164.21 7.307 .437 7.012 7.557 185.60 11.10 178.10 191.95 .180 .150 .180 .150 .180 .150 .180 .150 .180 .150 .180 With With Without Mounting Mounting Ears Mounting Ears and Inserts Ears 2-530655-1 2-530677-1 — 12-530689-11 — 2-530666-1 2-530655-2 — 2-530666-2 2-530656-2 — — 2-530655-3 — 2-530666-3 2-530655-4 12-530689-41 2-530655-5 — 2-530655-6 12-530689-61 2-530656-6 2-530655-8 2-530656-8 3-530655-2 3-530656-2 2-530655-9 12-530689-91 — 3-530655-0 13-530689-01 3-530655-3 3-530656-3 — — — — — — 2-530678-6 — — — — — — — — — 3-530677-3 — 2-530666-4 — 2-530666-5 2-530667-5 2-530666-6 12-531433-41 2-530667-6 12-531433-11 2-530666-8 3-530666-2 — 2-530666-9 — 2-530667-9 12-531433-21 2-530667-0 3-530666-3 3-530667-3 Flow Solder Post With Without Mounting Mounting Ears Ears Solder Eyelet Contact With Without Mounting Mounting Ears Ears .150 — — 2-530654-1 — .150 2-530657-2 — 2-530654-2 — .150 .180 2-530657-4 — — 2-530669-4 2-530654-4 — 2-530667-4 — .150 — 2-530668-5 2-530654-5 — .150 2-530657-6 2-530668-6 2-530654-6 — .150 — — 2-530654-7 — .150 3-530657-2 3-530668-2 3-530654-2 — — — — 2-530654-9 — .150 .180 — — — 3-530669-0 3-530654-0 — — — .150 3-530657-3 — 3-530654-3 — *Metric equivalents for post length are .150 = [3.81]; .180 = [4.57]. 1For .040 [1.02] diameter hole. Note: Other connector sizes can be made available, consult Tyco Electronics. 62 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors (Continued) Keying Plug Intercontact Key Material: Glass-filled nylon Part No. 650025-2 Recommended PC Board Edge Patterns .125 [3.18] Centerline Boards Intercontact KeySlot .300 Min. [7.52] .050 [1.27] .400 [10.16] .125 [3.18] .125 [3.18] .078± .005 .000 [1.98±0.13 0.00] .175 Min. [4.45] Recommended Gold Area .156 [3.96] Centerline Boards Intercontact KeySlot .300 Min. [7.52] .050 [1.27] .400 [10.16] .160 [4.06] .156 [3.96] .094± .005 .000 [2.39±0.13 0.00] .175 Min. [4.45] Recommended Gold Area 63 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors Product Facts ■ Wide variety of sizes available from 3 dual positions and up—no initial tooling investment required for new versions ■ Connectors can be selectively loaded with contacts in custom patterns ■ Connectors tooled on all standard centerlines— .100 [2.54], .125 [3.18], .150 [3.81], .156 [3.96], and .200 [5.08] Note: .200 [5.08] centerline capabilities provided by loading every-other dual position of .100 [2.54] centerline housings. ■ Closed card entry protects contacts and daughter board pads ■ Adapts to a wide range of mother board thicknesses to .104 [2.64] maximum ■ Phosphor bronze contacts selectively plated for top performance and maximum economy ■ Protective channel helps prevent overstress of contacts ■ Daughter board keying available in intercontact or on-contact styles ■ Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 *Consult Tyco Electronics engineering when paralleling contacts for power applications. The AMP Twin Leaf Connector is a highly reliable, low-cost mother/ daughter board connector designed for solid-state circuitry. The one-piece, multi-contact connector requires no front-end tooling. This versatile connector for double-sided printed circuit boards uses preloaded contacts and selective plating to give lowest applied cost. Critical contact areas are gold-over-nickel plated to provide positive electrical connection between contacts and daughter board pads. Contact posts are tin plated for efficient dip soldering to mother boards up to .104 [2.64] thick. The Twin Leaf Connector delivers high reliability because the contacts possess superior tolerance of environmental stresses including shock, vibration and variations of temperature and humidity. Other characteristics such as high insulation resistance, low termination resistance, long life and moderate contact separation force meet industry requirements for reliability. Connectors are tooled in sizes from 3 through 80 dual-contact positions with contacts on .100 [2.54], .125 [3.18], .150 [3.81], .156 [3.96] or .200 [5.08] centers. Other sizes and customloaded contact patterns are available on request. The connector housing, made of glass-filled polyester with a UL 94V-0 rating, features a standoff which facilitates the use of a probe for electrical continuity checks without risk of damage to the contacts. A closed card-entry design of the housing protects the contacts and daughter board pads. Housings accept daughter boards ranging from .055 [1.40] to .070 [1.78] in thickness. Intercontact and on-contact keys are available for polarization of the housings. Card guides or end caps make alignment of daughter board pads with Twin Leaf Connector contacts quick and easy. Performance Specifications Contact Rating*: 3 amperes continuous Temperature Rating: –55°C to +105°C Insulation Resistance: 5,000 megohms Dielectric Withstanding Voltage: Test Voltage (AC, RMS) Contact Spacing .100 [2.54] .150 [3.81] Sea Level 1,000 1,500 50,000 ft 400 600 15 240 m 70,000 ft 280 400 21 336 m Altitude Termination Resistance: 10 milliohms, max. Durability: Tested to 100 cycles (engage/withdraw) Contact Plating: .000015 [0.00038] selective gold plating on contact area; bright tin on solder tine 64 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors Without End Caps .100 [2.54], .125 [3.18], .150 [3.81] and .156 [3.96] Centerlines, With Solder Posts Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000015 [0.00038] gold in contact area; tin on posts, with entire contact underplated .000030 [0.00076] nickel, except where noted .400 [10.16] Fit for .055-.070 [1.4-1.78] PCBoard .225 [5.72] Card Slot Depth .400 [10.16] Max. .610 [15.49] A .135* or .170* [3.43] [4.32] B A Related Product Data: .010 x .024 [0.25 x 0.61] Post for .035 [0.89] Dia. Hole .200 [5.08] D Performance Specifications— page 64 Card Guides—pages 70, 71 Keying Plugs—page 72 PC Board Hole Layouts—page 71 *Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines, except where noted; .170 [4.32] for .100 [2.54] and .125 [3.18] centerlines, except where noted. Technical Documents: (pages 186, 187): Product Specification 108-9027 Instruction Sheets 408-7479, 408-7498, 408-7506 65 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors Without End Caps A = .100 [2.54] Centerline Spacing Part B D Numbers A = .125 [3.18] Centerline Spacing Part B D Numbers 2 — — — 3 .200 5.08 .400 10.16 No. of Dual Positions 4 — — 5 .400 10.16 .600 15.24 8 — — — 583485-6 — 583485-7 — — — — — — — — — — — — — — — — 1.000 25.40 1.250 31.75 A = .150 [3.81] Centerline Spacing Part B D Numbers .300 .600 1,31-583694-1 7.62 15.24 .300 .600 1,3 1,3 7.62 15.24 1-645155-1 .450 .750 583407-5 11.43 19.05 .600 .900 583407-6 15.24 22.86 1.050 1.350 583407-9 26.67 34.29 9 — — 10 .900 22.86 1.100 27.94 1-583485-2 — — — — — 11 — — — — — — 1.500 38.10 1.800 45.72 14 1.300 33.02 1.500 38.10 — — — — — — — 2.100 53.34 2.400 60.96 1-583407-5 15 18 20 22 28 — — — — — — — — — — 1-583485-6 — — — — 2.125 53.97 2.375 60.32 583533-7 — — 4-583486-8 — — — — — — — — — — — — — — 1.400 35.56 1.720 43.69 4-583486-1 — — — — — — — — — 2.964 75.28 3-583486-3 — — 1-583407-2 — — — 3.150 80.01 2-583407-0 530292-93 — — — — — 2.875 73.02 2-583533-0 — — — 4.050 102.87 4.350 110.49 — — — — 2.850 72.39 — 3.875 98.43 — .624 15.85 1-583533-6 2.625 66.67 — — .312 7.92 2.652 67.36 — — A = .156 [3.96] Centerline Spacing Part B D Numbers — — — 4.524 114.91 4.836 122.83 2-583486-3 — 4.212 106.99 4.524 114.91 583407-1 30 — — — 3.625 92.08 31 — — — — — — 4.500 53.34 4.800 60.96 530292-33 — — — 33 — — — — — — — — — 1-583486-8 36 — — — — — — — — — 3-583533-8 5.850 148.59 6.150 156.21 3-583407-8 5.304 134.72 5.772 146.61 6.396 162.46 6.864 174.35 7.960 202.18 8.892 225.86 531534-22 2-583486-1 56 — — — — — — — — — 4.992 126.80 5.460 138.68 6.084 154.53 6.552 166.42 7.640 194.06 8.580 217.93 65 6.400 162.56 7.900 200.66 6.600 167.64 8.100 205.74 5-583485-6 — — — — — — — — — 5-583485-5 — — — — — — — — — 40 43 50 80 — — — — — — 4.900 5.100 124.46 129.54 583485-3 4.875 5.125 123.83 130.18 — — — 6.130 6.380 1 155.70 162.05 5-583533-0 — — — 7.350 186.69 7.650 194.31 4-583407-8 1-583486-5 1-583486-1 583486-8 583486-1 5-583486-0 1Contacts are plated .000030 [0.00076] gold in contact area, tin on posts, with entire contact underplated .000030 [0.00076] nickel. length .135 [3.43] 3Post length .170 [4.32] Note: Other connector sizes can be made available, consult Tyco Electronics. 2Post 66 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors With End Caps .100 [2.54], .125 [3.18], .150 [3.81] and .156 [3.96] Centerlines, With Solder Posts Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000015 [0.00038] gold in contact area; tin on posts, with entire contact underplated .000030 [0.00076] nickel Related Product Data: Performance Specifications— page 64 Keying Plugs—page 72 PC Board Hole Layouts—page 71 Technical Documents: (pages 186, 187): Product Specification 108-9027 Instruction Sheets 408-7479, 408-7498, 408-7506 .400 [10.16] F Fit for .055-.070 [1.4-1.78] PCBoard .225 [5.72] Card Slot Depth .400 [10.16] Max. .610 [15.49] .135* or .170* [3.43] [4.32] .062 [1.58] A B E** G Accepts #2 Self-tapping Screw .200 [5.08] .010 x .024 [0.25 x 0.61] Post for .035 [0.89] Dia. Hole **Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines; .170 [4.32] for .100 [2.54] and .125 [3.18] centerlines. **See page 27 for dimensions. 67 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors With End Caps No. of Dual Pos. 3 5 6 7 9 10 12 13 A = .100 [2.54] Centerline Spacing Part B F G Numbers .200 .400 .734 1-583715-1 5.03 10.16 18.64 .400 .600 .934 1-583715-3 10.16 15.24 23.72 .500 .700 1.034 1-583715-4 12.70 17.78 26.26 .600 .800 1.134 1-583715-5 15.24 20.32 28.80 .800 1.000 1.334 1-583715-7 20.32 25.40 33.88 .900 1.100 1.434 1-583715-8 22.86 27.94 36.42 1.100 1.300 1.634 1-583715-0 27.94 33.02 41.50 1.200 1.400 1.734 1-583715-1 30.48 35.56 44.04 A = .125 [3.18] Centerline Spacing Part B F G Numbers — — — A = .150 [3.81] Centerline Spacing Part B F G Numbers B — — — — — — — — — — — — — — — — — 1.259 31.96 1-583679-5 — — — — .780 19.81 1.092 27.74 1.538 39.07 1-583660-6 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 1.716 43.59 2.028 51.51 2.162 54.91 2.474 62.84 1-583660-0 — 1.404 35.66 1.716 43.58 — — — — — — — — — — — — — 2.250 57.15 2.400 60.96 2.684 68.17 2.834 71.98 1-583692-3 2.340 59.44 2.496 63.40 2.786 70.76 2.942 74.73 1-583660-4 1-583692-4 2.028 51.51 2.184 55.47 — — — — — — — 2.652 67.36 2.964 75.28 3.410 86.61 1-583660-7 — — — — 15 1.934 49.12 2.134 54.20 2.234 56.74 2.434 61.82 1-583715-3 — — — — 1-583715-5 2.250 57.15 2.375 60.33 2.625 66.68 2.634 66.90 2.759 70.08 3.009 76.43 — 1-583715-8 2.000 50.80 2.125 53.98 2.375 60.33 1-583679-6 20 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 22 — — — — — — — 25 2.400 60.96 2.500 63.50 2.700 68.58 2.900 73.66 3.000 76.20 3.100 78.74 2.600 66.04 2.700 68.58 2.900 73.66 3.100 78.74 3.200 81.28 3.300 83.82 2.934 74.52 3.034 77.05 3.234 82.14 3.434 87.22 3.534 89.76 3.634 92.30 2-583715-3 3.000 76.20 3.250 82.55 2-583715-4 — — 2-583715-6 3.375 85.73 3.625 92.08 26 28 30 31 32 — — — — — — 1-583679-9 — — — — — — — — — — — — — 2-583679-4 3.600 91.44 3.900 99.06 4.334 110.08 2-583692-4 3.588 91.14 4.065 103.02 4.034 102.46 4.502 114.35 2-583660-1 3.634 92.30 3.276 83.21 3.744 95.10 — — — — — — — — — — 4.524 114.91 4.836 122.83 4.979 126.24 5.282 134.16 2-583660-7 4.009 101.83 2-583679-6 — — — — 4.650 118.11 5.084 129.13 1-583692-1 — — — — — — — 5.148 130.76 5.594 142.09 3-583660-1 — — — — — — — — — — — — — — — 5.100 129.54 5.534 140.56 3-583692-1 — — — — — — — — — 5.616 142.64 5.772 146.61 6.062 153.97 6.218 157.94 3-583660-4 3-583692-4 5.304 134.72 5.460 138.68 3-583692-8 — — — — 33 — — — — — — — — 34 3.500 88.90 3.600 91.44 3.700 93.98 4.100 104.14 4.200 106.68 3.834 97.38 3.934 99.92 4.034 102.46 4.434 112.62 4.534 115.16 3-583715-2 — — — — — — — 5.100 129.54 5.250 133.35 5.850 148.59 5.400 137.16 5.550 140.97 6.150 156.21 5.834 148.18 5.984 151.99 6.584 167.23 3-583692-3 41 3.300 83.82 3.400 83.36 3.500 88.90 3.900 99.06 4.000 101.60 43 — — — 50 4.900 124.46 7.900 200.66 5.100 129.54 8.100 205.74 5.434 138.02 8.434 214.22 36 40 80 2-583660-9 4.836 122.83 4.800 121.92 35 2-583660-4 4.212 106.98 4.524 114.91 2-583715-9 — 1-583660-2 — 2-583715-8 — 1-583660-2 1-583679-7 4.350 110.49 3-583715-0 — .875 22.23 1.400 35.56 1.600 40.64 1.700 43.18 1.900 48.26 1-583715-6 — — 14 18 — .625 15.88 1.950 49.53 2.100 53.34 17 A = .156 [3.96] Centerline Spacing Part F G Numbers 3-583715-3 — — — — 3-583715-4 — — — — 3-583715-8 4.875 123.83 3-583715-9 — — — — — — — — — — — — — — — — — — — — — 6.125 155.58 7.350 186.69 7.650 194.31 8.084 205.33 4-583692-8 6.864 174.35 7.956 202.08 7.310 185.67 8.402 213.41 4-583660-1 4-583715-8 6.552 166.42 7.644 194.16 5-583715-7 — — — — — — — — — 5.125 5.509 130.18 139.93 3-583679-8 6.375 6.759 161.93 171.68 4-583679-8 — — — 1-583660-1 4-583660-8 Note: Other connector sizes can be made available, consult Tyco Electronics. 68 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors With End Caps (Continued) Typical Connector and Card Guide Assembly Double Slotted Card Guide (Without Stand-off) Single Slotted Card Guide Double Slotted Card Guide (With Stand-off) End Cap Stand-off Daughter Board Mother Board .104 [2.64] Max. Thickness* Self-tapping #2 Screw (2 Reqd.) Self-tapping #2 Screw (1 Reqd.) Self-tapping #2 Screw (2 Reqd.) *Must be .063 [1.59] thick for use with Double Slotted Card Guides. 69 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors (Continued) Card Guides Single Slotted Material: Glass-filled nylon, black .210 [5.33] Part No. 583671-1 Related Product Data: 3.770 [95.76] .074 .523 Dia. [1.88] [13.28] .225 [5.72] Thru Hole .170 [4.32] 3.585 [91.06] Connectors used with—page 65 .137 [3.48] .074 [1.88] Dia. x .175 [4.45] Deep Technical Documents: (pages 186, 187): Instruction Sheets 408-7498, 408-7506 Single Slotted Card Guide and Connector Mounting .100 [2.54] Contact Centerline Connector Centerline .091 [2.31] Dia. A .200 [5.08] .035 Dia. [0.89] Mounting Hole E Min. .225 [5.72] Dimensions A E .100 .263 2.54 6.68 .125 .288 3.18 7.31 .150 .313 3.81 7.95 .156 .319 3.96 8.10 70 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors (Continued) Double Slotted Without Stand-off Card Guides (Continued) 1.680 [42.67] .080 [2.03] Material: Nylon, natural 1.500 [38.10] .150 [3.81] .540 [13.72] Part No. 583425-1 Related Product Data: Connectors used with—page 65 .300 [7.62] .400 [10.16] Technical Documents: (pages 186, 187): Instruction Sheets 408-7498, 408-7506 Double Slotted Card Guide and Connector Mounting .100 [2.54] Contact Centerline Connector Centerline .310 [7.87] .175 [4.45] A .200 [5.08] .035 Dia. [0.89] Mounting Hole E Min. Dimensions A E .100 .328 2.54 8.33 .125 .353 3.18 8.96 .150 .376 3.81 9.60 .156 .384 3.96 9.75 Note: Mother Board must be .063 [1.59] thick for use with Double Slotted Card Guides. Recommended PC Board Layout for Connectors With End Caps Contact Centerline .100 [2.54] .200 [5.08] .100 [2.54] Dia. Connector Centerline .035 Dia. [0.89] Mounting Hole A E Dimensions A E .100 .267 2.54 6.78 .125 .317 3.18 8.05 .150 .367 3.81 9.32 .156 .379 3.96 9.62 71 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors (Continued) Keying Plugs Material: Nylon, natural Technical Documents: (pages 186, 187): Instruction Sheet 408-7479 Type A Type B Intercontact In-Row Contact Spacing Type of Contact .100 2.54 Solder Post Card Extender Solder Post Card Extender Solder Post Wrap-Type Post Card Extender Solder Post Wrap-Type Post Card Extender .125 3.18 .150 3.81 .156 3.96 Connector Style* with without End Caps End Caps 583715 583485 530268 530291 583679 583533 530265 530290 583692 583407 583754 583752 530278 530270 583660 583486 583755 583753 530267 530282 Type A Part Numbers On-Contact Intercontact Keying Plug Type B Insertion/Extraction Part Numbers Tool On-Contact Keying Plug Part Insertion/Extraction Numbers Tool 530286-3 — 91081-2 583714-1 91088-1 530286-2 530030-1 91081-1 583714-1 91088-1 530286-2 530030-1 91081-1 — — 530286-2 530030-1 91081-1 — — *Refer to pages 66-68, as applicable, for specific connector sizes. Dimension A Connector Centerlines Intercontact On-Contact .100 .040 .129 2.54 1.02 3.28 .125 .050 .129 3.18 1.27 3.28 .150 .050 .160 3.81 1.27 4.06 .156 .050 .160 3.96 1.27 4.06 A .475 [12.06] Min. Recommended PC Board Cutout for Keying Plugs Other Twin Leaf Mother Board Connectors Card Extender Connectors .400 [10.16] For more information on the connectors shown here, consult Tyco Electronics. Fits for .055-.070 [1.4-1.78] PCBoard Connectors With End Caps .225 [5.72] .610 [15.49] Centerlines Part Number Series* .150 3.81 .156 3.96 530278 530267 *Consult Tyco Electronicsfor specific connector sizes. 72 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors Product Facts ■ Zero insertion force; little or no effort required to insert and withdraw PC boards ■ Reduced pad wear for extended board life ■ Allows all four sides of board to be used for input/output functions ■ Accepts double-sided boards ■ Three contact styles to choose from: vertical solder post, right-angle solder post and wrap-type post (2 and 3 high) ■ Available in .100 [2.54], .125 [3.18] and .156 [3.96] centerlines ■ Three configurations available: open one end, open both ends and closed both ends ■ Products indicated are recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Performance Specifications Current vs. Temperature Rise*: 3 amperes at 30°C Operating Temperature: –55°C to +105°C Contact Resistance: 20 milliohms max. Durability: Tested to 5000 cycles AMP Rotary Cam Zero Insertion Force (ZIF) Card Edge Connectors are available in sizes to fit most industry-standard printed circuit boards. A clockwise rotation of the cam handle opens contacts to allow zero-force insertion or removal of PC boards— even boards with a large number of contacts. Turning the cam handle to close the connector locks the board securely in place. Rotary Cam ZIF Connectors accept double-sided PC boards .054-.070 [1.37- 1.78] thick, with contact centerline intervals of .100 [2.54], .125 [3.18] and .156 [3.96]. Row-to-row spacing of connector posts is .200 [5.08] for .100 [2.54] and .156 [3.96] connectors and .250 [6.35] for .125 [3.18] connectors. Contacts are nickel underplated phosphor bronze with gold plate in the contact area and tin-lead plated posts. Contact configurations include vertical and right-angle solder posts and wrap-type posts. Preassembled connectors feature housings made from 94V-0 rated glass-filled polyester and mounting ears for easy mounting to the mother board. Housings are available with one end open, both ends open and both ends closed for side and top daughter board insertion. Integral board locks secure boards in the connectors. Accessories include dust covers, cam rods (with and without boots) and cam keys for nut-driver actuation and for tandem operation of connectors. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 73 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End .440 [11.18] .370 [9.40] Related Product Data: Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 B Closed Position .150 [3.81] .250 [6.35] 1.095 [27.81] Ref. .850 [21.60] .050 [1.27] Technical Documents: (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 .210 [5.33] .100 [2.54] Typ. A D C No. of Dual Positions A B 22 2.100 53.34 2.800 71.12 25 2.400 60.96 28 2.700 68.58 3.000 76.20 31 Dimensions C .125 .160 .125 .160 Closed Both Ends 1-531019-1 — 1-531019-2 — 2.900 73.66 3.200 81.28 .160 21-531020-3 — — .160 2-531020-1 — — .125 .160 .125 .160 .125 3-531020-2 1-531020-4 1-531020-5 1-531020-5 3-531020-3 1-531020-7 22-531020-82 1-531020-8 1-531020-8 22-531020-92 — — — — — — — 531021-8 — — 1-531019-4 — — — — — — — 1-531019-8 — .160 1-531020-9 1-531021-9 1-531019-9 .125 1-531020-0 2-531020-0 23-531020-02 — — — — — — 3.100 78.74 2.300 58.42 3.100 78.74 3.400 86.36 2.600 66.04 3.400 86.36 3.700 93.98 3.700 93.98 4.000 101.60 4.200 106.68 4.500 114.30 3.700 93.98 40 3.900 99.06 4.600 116.84 4.900 124.46 4.100 104.14 43 4.200 106.68 4.900 124.46 5.200 132.08 4.400 111.76 50 4.900 124.46 5.600 142.24 5.900 149.86 5.100 129.54 60 5.900 149.86 6.600 167.64 6.900 175.26 6.100 154.94 7.100 180.34 7.400 187.96 .200 [5.08] Part Numbers Open Both Ends1 — — — — E* 3.500 88.90 6.400 162.56 .018 [0.46] Typ. E Open One End1 1-531020-1 1-531020-1 1-531020-2 1-531020-2 D 36 65 .025 [0.64] Typ. 6.600 167.64 .160 .125 .160 .160 *Metric equivalents in millimeters for post lengths E are .125 = [3.18]; .160 = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. 2Connectors without cam rod and boardlock. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 74 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued) Right-Angle Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—page 82, 96 .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End .440 [11.18] .370 [9.40] B Closed Position .150 [3.81] Technical Documents: (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 .250 [6.35] 1.095 [27.81] Ref. .160 [4.06] .050 [1.27] .850 [21.60] .025 [0.64] Typ. .210 [5.33] .100 [2.54] Typ. A .025 [0.64] Typ. D .200 [5.08] .100 [2.54] C Bend Right Shown No. of Dual Positions 25 36 50 65 A 2.400 60.96 3.500 88.90 4.900 124.56 6.400 162.56 Dimensions B C 3.100 78.74 4.200 106.68 5.600 142.24 7.100 180.34 D 3.400 86.36 4.500 114.30 5.900 149.86 7.400 187.96 2.800 71.12 3.700 93.98 5.100 129.54 6.600 167.64 Bend Right Part Numbers (Open End1) R 1-531395-23 R 1-531396-4 L 1-531396-8 R 1-531396-0 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown. 2. Other connector sizes can be made available, consult Tyco Electronics. 3. Open both ends. 75 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued) Vertical Connector, Wrap-Type Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 .370 [9.40] .440 [11.18] B Closed Position .150 [3.81] .250 [6.35] Technical Documents: (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 1.095 [27.81] Ref. .050 [1.27] .850 [21.60] .025 [0.64] Typ. .100 [2.54] Typ. .210 [5.33] A E .025 [0.64] Typ. .200 [5.08] D C No. of Dual Positions A 25 2.400 60.96 Part Numbers Open Open One End1 Both Ends1 B Dimensions C D E* 3.100 78.74 3.400 86.36 2.600 66.04 .380 1-531414-2 — 1-531414-4 1-531414-4 1-531415-4 — 36 3.500 88.90 4.200 106.68 4.500 114.30 3.700 93.98 .580 .380 40 3.900 99.06 4.100 104.14 4.900 124.46 5.900 149.86 6.400 162.56 4.600 116.84 4.800 121.92 5.600 142.24 6.600 167.64 7.100 180.34 4.900 124.46 5.100 129.54 5.900 149.86 6.900 175.26 7.400 187.96 4.100 104.14 4.300 109.22 5.100 129.54 6.100 154.94 6.600 167.64 .580 1-531414-5 — .380 1-531414-6 — .580 2-531414-4 1-531415-8 .580 1-531414-9 — .580 1-531414-0 — 42 50 60 65 *Metric equivalents in millimeters for post lengths E are .580 = [14.73] (3-high wrap-type); .380 = [9.65] (2-high wrap-type). 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 76 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .125 x .250 [3.18 x 6.35] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End .440 [11.18] .370 [9.40] B Closed Position .150 [3.81] Technical Documents: (pages 186,187): Product Specification 108-9048 Instruction Sheet 408-7911 .250 [6.35] 1.095 [27.81] Ref. .850 [21.60] .210 [5.33] .125 [3.18] Typ. A D C .050 [1.27] .025 [0.64] Typ. .018 [0.46] Typ. E .250 [6.35] Part Numbers Open Open One End1 Both Ends1 No. of Dual Positions A B Dimensions C D E* 28 3.375 85.73 4.125 104.76 4.425 112.40 3.625 92.08 .125 — 1-531024-3 30 3.625 92.08 4.375 111.13 4.675 118.75 3.875 98.43 .125 1-531023-4 — 40 4.875 123.83 5.625 142.88 5.925 150.50 5.125 130.18 .160 1-531023-4 1-531024-4 *Metric equivalents in millimeters for post lengths E are .125 = [3.18]; .160 = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 77 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .156 x .200 [3.96 x 5.08] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 .440 [11.18] .370 [9.40] B Closed Position .150 [3.81] Technical Documents: .250 [6.35] (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 1.095 [27.81] Ref. .850 [21.60] .210 [5.33] .156 [3.96] Typ. A D C No. of Dual Positions A B 22 3.276 83.21 4.088 103.83 36 5.460 138.68 43 6.552 166.42 Dimensions C .050 [1.27] .025 [0.64] Typ. E .018 [0.46] Typ. .200 [5.08] Part Numbers Open Both Ends1 — — Closed Both Ends — 531007-9 D E* 4.388 111.46 3.588 91.14 .125 .160 Open One End1 531025-3 531025-9 6.272 159.31 6.572 166.93 5.772 146.61 .160 — 1-531026-1 — 7.364 187.05 7.664 194.67 6.864 174.35 .125 531025-6 — — *Metric equivalents in millimeters for post lengths E are .125 = [3.18]; .160 = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 78 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Accessories Dust Covers A Material: Rigid vinyl, black Dimension A 11.050 280.67 48.000 1219.20 Part Numbers 531863-2 531863-1 Note: Other lengths can be made available upon request, consult Tyco Electronics. .348 [8.84] Cam Rods with Boot Material: Cam Rod—Stainless steel Boot—Glass-filled polyester, yellow .654 [16.61] .835 [21.21] .200 [5.08] .200 [5.08] Dimension A 3.185 80.90 3.705 94.11 4.470 113.54 5.285 134.24 5.900 149.86 5.975 151.77 Part Numbers 650083-1 650083-2 650083-3 650083-4 650083-6 532563-7 .400 [10.16] Dimension A 6.385 162.18 6.985 177.42 7.485 190.12 7.725 196.22 8.320 211.34 A Part Numbers 650083-7 650083-8 650083-9 1-532563-0 1-650083-7 Note: Other lengths can be made available upon request, consult Tyco Electronics. 79 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Accessories (Continued) Cam Rods without Boot .125 [3.18] Material: Stainless steel .775 [19.69] .200 [5.08] .055 [1.40] .045 [1.14] A Dimension A 2.200 55.88 2.700 68.58 3.300 83.82 4.750 120.65 5.000 127.00 5.500 139.70 Dimension A 6.000 152.40 6.250 158.75 6.750 171.45 8.250 209.55 12.500 317.50 Part Numbers 2-531004-8 2-531004-9 3-531004-0 2-531004-4 1-531004-4 2-531004-6 Part Numbers 2-531004-7 1-531004-6 1-531004-7 3-531004-2 2-531004-0 Note: Other lengths can be made available upon request, consult Tyco Electronics. .125 [3.18] .252 [6.40] .055 [1.40] .260 [6.60] .045 [1.14] A Dimension A 3.380 85.85 4.50 114.30 5.200 132.08 6.90 175.30 13.120 333.25 Part Numbers 645293-3 645293-8 645293-6 645293-7 645293-5 Note: Other lengths can be made available upon request, consult Tyco Electronics. 80 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Recommended PC Board Hole Layouts Mother Board Hole Layout, Vertical Through-Board Connectors .048 Dia. Typ. [1.22] .128 Dia. [3.25] (2 Plc.) W CL A* X B* *Refer to individual connector specifications. CL W X .100 2.54 .125 2.18 .156 3.96 .200 5.08 .250 6.35 .200 5.08 .350 8.89 .375 9.53 .406 10.31 Mother Board Hole Layout, Right-Angle Through-Board Connectors .100 Typ. [2.54] .200 [5.08] .048 Dia. Typ. [1.22] Pin No. 1 (Ref.) .400 Max. [10.16] A* PCBoard Edge *Refer to individual connector specifications. 81 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Recommended PC Board Edge Pattern Daughter Board Edge Pattern .700 [17.78] Min. .270 [6.86] Min. CL C CL Minus .006 [0.15] +.005 -.000 [+0.13] A ±.005 B [±0.13] CL = .100 [2.54] C = .050 [1.27] A B 2.100 2.288 53.34 58.12 2.400 2.588 60.96 65.74 2.700 2.888 68.58 73.36 No. of Dual Positions 22 25 28 30 — — 31 3.000 76.20 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 6.400 162.56 3.188 80.98 3.688 93.68 4.088 103.84 4.388 111.46 5.088 129.24 6.088 154.64 6.588 167.34 36 40 43 50 60 65 Special Application CL = .125 [3.18] C = .078 [1.98] A B — CL = .156 [3.96] C = .094 [2.39] A B 3.267 3.576 83.21 90.83 — — — — — 3.375 85.73 3.625 92.08 3.613 91.77 3.863 98.12 — — — — — — — — — — 5.460 138.68 5.760 146.30 4.875 123.83 5.113 129.87 — — — — 6.552 166.42 6.852 174.04 — — — — — — — — — — — — Tandem Application Special Rod (Part No. Series 645293) Allows Customer Supplied Nut Driver Actuation (Refer to page 80.) Note: Contact Tyco Electronics for information concerning special tandem connectors. 82 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors Product Facts ■ Minimizes force needed to install and remove printed circuit boards ■ Available in lever and bell crank styles ■ Lever styles allow side and top card entry ■ Wiping action contacts enhance electrical properties ■ Contacts on .100 x .100 [2.54 x 2.54] or .125 x .125 [3.18 x 3.18] centers ■ .025 [0.64] square posts ■ Accepts PC boards from .054 to .070 [1.37 to 1.78] in thickness ■ Normally closed design leaves springs in relaxed position ■ 50 to 175 dual positions available on .100 [2.54] centerline connectors and 40 to 140 dual positions available on .125 [3.18] centerline connectors Performance Specifications Current vs. Temperature Rise*: 3 amperes at 30°C Operating Temperature: –65°C to +85°C Contact Resistance: 16 milliohms max. Durability: Tested to 250 cycles (board-to-contact actuation) *Consult Tyco Electronicsengineering when paralleling contacts for power applications. AMP Linear Zero Insertion Force (ZIF) PC Board Edge Connectors are available in both lever and bell crank actuated styles and can be provided as panel assemblies, separate housings and contacts or as preassembled with solder post terminals. Panel assemblies include a housing with ACTION PIN press-fit solderless contacts mounted on an epoxy board for rack application. Separate housing assemblies and ACTION PIN contacts allow customer assembly. These can be mounted as close as .625 [15.88]. More design latitude for high density application is provided by the side entry lever-type connector, permitting use of all sides of the PC board for edge-type I/O connections (see page 133). Where solder applications are required, Tyco Electronics has a line of preassembled connectors with tin-plated solder terminals. All these configurations are available in a broad range of sizes. and housing modules without removing the entire housing assembly from the board. With ZIF style connectors, intermittencies can occur if a contact comes to rest on a piece of foreign matter (dust and dirt particles) found on PC boards. To decrease the probability of this happening, all connectors have been designed to include a wiping contact which produces a wiping action. This action, produced by the geometry and bending movements of the beam, pushes aside debris and allows for good electrical connection by cleaning the actual point of contact. In addition, all connectors have removable wings which make it possible to repair or replace damaged cam rails, handles, contacts 83 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline Housing with Solder Posts Lever Style, Side Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] min. gold per MIL-G-45204 in contact area; .000100 [0.00254] min. tin-lead on post with entire contact underplated .000050 [0.00127] min. nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 Special Application—page 96 Technical Documents: (pages 186, 187): Product Specification 108-14015 Application Specification 114-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 .450 [11.43] A .500 [12.70] Max. B C L Last Contact Position .355 [9.02]* Closed .103 [2.62] Closed End C Open End Open .845 [21.46] .600 [15.24] C L First Contact Position P .100 Typ. [2.54] Mounting Hole C L .100 [2.54] .190 [4.83] P .845 [21.46] .175 [4.45] .206 [5.23] Mounting Hole CL 1.075 [27.31] Section P-P *Card slot depth. No. of Dual Positions 35 80 100 A Dimensions B C 6.113 155.27 11.613 294.97 13.613 345.77 3.400 86.36 7.900 200.66 9.900 251.46 2.000 50.80 3.000 76.20 3.000 76.20 Part Number 1-645135-2 1-645135-1 1-645135-5 Note: Other connector sizes can be made available, consult Tyco Electronics. 84 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Panel Assembly Lever Style, Side Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 ACTION PIN Contacts— pages 88, 94 Tooling—page 95 Special Application—page 96 .343 [8.71] Max. PC Board Channel .355 [9.02] Card Slot Depth Open End Closed End C Technical Documents: 1.555 [39.50] (pages 186, 187): Product Specification 108-14015 Application Specification 114-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 .125 [3.18] D 1.425 [36.16] .150 [3.81] Countersunk Hole (2 Plcs.) .812 [20.62] A .100 [2.54] Typ. .100 [2.54] .750 [19.05] B No. of Dual Positions 75 100 130 140 150 160 160 Dimensions A B C D 7.400 251.46 9.900 251.46 12.900 251.46 13.900 353.06 14.900 251.46 15.900 403.86 15.900 403.86 10.125 320.68 12.625 320.68 15.625 320.68 16.625 422.28 17.625 320.68 18.625 473.07 18.625 473.07 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 .615 15.62 .615 15.62 .615 15.62 .615 15.62 .615 15.62 .615 15.62 .455 11.56 Part Numbers 1-645145-0 1-645145-5 2-645145-1 2-645145-3 2-645145-5 2-645145-7 147400-1 Note: Other connector sizes can be made available, consult Tyco Electronics. 85 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Panel Assembly Lever Style, Top Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 ACTION PIN Contacts— pages 88, 94 Tooling—page 95 .343 [8.71] Max. PC Board Channel .355 [9.02] Card Slot Depth Technical Documents: (pages 186, 187): Closed End Product Specifications 108-14015, 108-26003 Application Specification 114-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 Closed End C 1.555 [39.50] .125 [3.18] .615 [15.62] 1.425 [36.16] .150 [3.81] Countersunk Hole (2 Plcs.) .812 [20.62] A .100 [2.54] Typ. .100 [2.54] .750 [19.05] B No. of Dual Positions 110 120 A Dimensions B C 10.900 276.86 11.900 302.26 13.625 346.08 14.625 371.48 3.000 76.20 3.000 76.20 Part Numbers 1-645147-7 1-645147-9 Note: Other connector sizes can be made available, consult Tyco Electronics. 86 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Housing Lever Style, Side Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Mounting Screws—Customer supplies, must be applied before opening connector Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 ACTION PIN Contacts— pages 88, 94 Tooling—page 95 Special Application—page 96 A Ref. Technical Documents: (pages 186, 187): B Product Specifications 108-14015, 108-26003 Application Specification 108-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 C L Last Contact Position Closed C L First Contact Position Open End C Open Closed End P .450 [11.43] P Mounting Hole C L .355 [9.02]* .815 [20.70] .206 [5.23] .600 [15.24] No. of Dual Positions A 7.613 4.900 193.37 124.46 11.113 7.400 75 282.27 187.96 11.613 7.900 80 294.97 200.66 13.613 9.900 100 345.77 251.46 14.613 10.900 110 371.17 276.86 15.113 11.400 115 383.87 289.56 16.113 12.400 125 409.27 314.96 16.613 12.900 130 421.97 327.66 17.613 13.900 140 447.37 353.06 19.613 15.900 160 498.17 403.86 21.113 17.400 175 536.27 441.96 Note: Other connector sizes can be made available, consult Tyco Electronics. 50 Section P-P *Card slot depth. Dimensions B Part Numbers C 2.000 50.80 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 1-645115-5 1-645115-0 1-645115-1 1-645115-5 1-645115-7 3-645115-2 1-645115-8 2-645115-0 2-645115-1 2-645115-3 3-645115-3 3-645115-0 87 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) ACTION PIN Contacts with Wiping Feature, .100 [2.54] Centerline Recommended PC Board Hole Layout and Edge Pattern, .100 [2.54] Centerline Material and Finish: Related Product Data: Mother Board Hole Layout Copper alloy 725, plated .000015 [0.00038] gold per MIL-G-45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G-45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Performance Specifications— page 83 ACTION PIN Contact Description and Application Specification— page 94 Tooling—page 95 .047 Dia. Typ. [1.19] (Solder Post Only)* .120 Dia. [3.05] CL Technical Documents: C B (pages 186, 187): *For ACTION PIN post hole diameter, see page 94. Instruction Sheet 408-2665 Connector Style CL Lever .100 2.54 A (Comb) Dimensions A B .100 .206 2.54 5.23 C .175 4.45 .045 [1.14] Contact Area Prenotched for Breakoff at Assembly Daughter Board Edge Pattern .745 [18.92] .200 Min. [5.08] .600 Ref. [15.24] 1.485 [37.72] B Min. Prenotched for Breakoff at Assembly .098 Typ. [2.49] A Max. .100 [2.54] .070 [1.78] .100 [2.54] .740 [18.80] Post Area .100 (No. of Pos. –1) +.196 [2.54 (No. of Pos. –1) +4.98] .025 Sq. [0.64] Contact Combs Number of Contacts Per Comb* Dimension A 55 5.400 137.16 Part Number Connector Style 4-119311-1 *At least two (2) contact combs required per housing. Note: Other sizes can be made available, consult Tyco Electronics. Entry Style Side Lever Top Dimensions A .240 6.10 .240 6.10 B — .320 8.13 Reeled Contacts Number of Contacts Per Reel 35,000 Part Number 119196-6 Note: Other plating combinations and thicknesses can be made available, consult Tyco Electronics. 88 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline Panel Assembly Lever Style, Side Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Special Application—page 96 PC Board Channel .343 Max. [8.71] Technical Documents: .355 [9.02] Card Slot Depth Open End (pages 186, 187): Closed End C Instruction Sheets 408-2995, 408-6915, 408-6916 .615 [15.62] .125 [3.18] 1.425 [36.16] .150 [3.81] Countersunk Hole (2 Plcs.) .812 [20.62] A .125 Typ. [3.18] 1.555 [39.50] .125 [3.18] .750 [19.05] B No. of Dual Positions 40 56 60 72 84 124 A Dimensions B C 4.875 123.83 6.875 174.63 7.375 187.32 8.875 225.43 10.375 250.83 15.375 390.53 7.625 193.68 9.625 244.48 10.125 257.17 11.625 295.28 13.125 320.68 18.125 460.38 2.000 50.80 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 Part Numbers 1-645146-5 1-645146-9 1-645146-0 1-645146-3 1-645146-6 2-645146-6 Note: Other connector sizes can be made available, consult Tyco Electronics. 89 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) Panel Assembly Bell Crank Style, Top Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Technical Documents: .935 Max. [23.75] (pages 186, 187): .355 [9.02] Card Slot Depth Instruction Sheets 408-2995, 408-6915, 408-6916 3.620 Ref. [91.95] (Open) Closed End 1.555 [39.50] .125 [3.18] .615 [15.62] 2.41 [54.38] .609 [15.47] A .125 [3.18] .125 Typ. [3.18] .750 [19.05] B No. of Dual Positions 60 80 112 140 Dimensions A B 7.375 187.33 9.875 250.82 13.875 352.43 17.375 441.33 10.625 269.88 13.125 333.38 17.125 434.98 20.625 523.88 Part Numbers 1-645149-0 1-645149-5 2-645149-3 3-645149-0 Note: Other connector sizes can be made available, consult Tyco Electronics. 90 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) Housing Lever Style, Side Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Mounting Screws—Customer supplied, must be applied before opening connector Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Special Application—page 96 Technical Documents: (pages 186, 187): Instruction Sheets 408-2995, 408-6915, 408-6916 .475 [12.07] A Ref. .355 [9.02]* B .815 [20.7] CL First Contact Position Closed .600 [15.24] CL Last Contact Position Open End C Open 1.087 [27.61] Section P-P No. of Dual Positions 84 100 112 124 .115 [2.92] P .218 [5.54] Mounting Hole CL *Card slot depth. Closed End P Mounting Hole CL A Dimensions B C 14.112 358.44 16.112 409.24 17.612 447.34 19.112 485.44 10.375 263.52 12.375 314.33 15.775 400.68 17.275 438.78 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 Part Number 1-645116-6 2-645116-0 2-645116-3 2-645116-6 Note: Other connector sizes can be made available, consult Tyco Electronics. 91 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) Housing Bell Crank Style, Top Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Mounting Screws—Customer supplied, must be applied before opening connector Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Technical Documents: (pages 186, 187): Instruction Sheets 408-2995, 408-6915, 408-6916 .475 [12.07] A Ref. 1.062 [26.97] (Open) 1.874 [47.60] .312 [7.92] B CL Last Contact Position CL First Contact Position .500 [12.70] .355 [9.02]* Closed End .815 [20.7] .600 [15.24] .115 [2.92] 2.562 [65.07] (Closed) P .115 [2.92] 1.820 [46.23] Mounting Hole CL P 1.250 [31.75] Mounting Hole CL .187 [4.75] Section P-P *Card slot depth. No. of Dual Positions 52 60 80 112 Dimensions A B 8.562 217.47 9.562 242.87 13.125 333.37 16.062 407.97 6.375 161.93 7.375 187.32 9.875 250.82 13.875 352.43 Part Numbers 1-645142-8 1-645142-0 1-645142-5 2-645142-3 Note: Other connector sizes can be made available, consult Tyco Electronics. 92 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) ACTION PIN Contacts with Wiping Feature, .125 [3.18] Centerline Recommended PC Board Hole Layout and Edge Pattern, .125 [3.18] Centerline Material and Finish: Related Product Data: Copper alloy 725, plated .000015 [0.00038] gold per MIL-G-45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G-45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Performance Specifications— page 83 ACTION PIN Contact Description and Application Specification— page 94 Tooling—page 95 Mother Board Hole Layout .047 Dia. Typ. [1.19] (Solder Post Only)* .120 Dia. [3.05] CL Technical Documents: C B (pages 186, 187): *For ACTION PIN post hole diameter, see page 94. Instruction Sheet 408-2665 Connector Style Lever A (Comb) Bell-Crank .045 [1.14] Contact Area Dimensions A B .125 .218 3.18 5.54 .125 1.250 3.18 31.75 CL .125 3.18 .125 3.18 C .187 4.75 .187 4.75 Prenotched for Breakoff at Assembly Daughter Board Edge Pattern .750 [19.05] .600 Ref. [15.24] 1.490 [37.85] .200 Min. [5.08] B Min. .740 [18.80] Post Area .125 [3.18] .110 Typ. [2.79] .025 Sq. [0.64] .125 [3.18] A Max. .090 Typ. [1.78] .125 (No. of Pos. –1) +.220 [3.18 (No. of Pos. –1) +5.59] Contact Combs Number of Contacts Per Comb* Dimension A 56 6.875 174.63 Part Number Connector Style Side 1-119950-2 *At least two (2) contact combs required per housing. Note: Other sizes can be made available, consult Tyco Electronics. Entry Style Lever Top Bell-Crank Top Dimensions A .240 6.10 .240 6.10 .775 19.68 B — .320 8.13 .600 15.24 93 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide break-through and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today’s standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. ➀ Annular Ring (See Note) ➁ Drilled Hole ➂ Copper Thickness ➃ Tin-Lead Thickness ➄ Plated Through-Hole ACTION PIN Contact/PC Board Applications Connector Type ACTION PIN Contact Material Thickness Drilled Hole Diameter➁ Linear ZIF .025 0.64 .0453±.001 1.151±0.03 Plating Thicknesses Copper➂* Tin-Lead➃ .001-.003 0.03-0.08 .0003 0.008 Min. Plated Through-Hole Diameter➄ .037-.043 0.94-1.09 Radial Hole Distortion Average Maximum Not Specified Not Specified *Maximum hardness of copper layer is 150 Knoop. Note: Recommended annular ring diameter is hole diameter plus .020 [0.51]. 94 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors (Continued) Assembly tooling is not required except when using connectors with ACTION PIN contacts. ACTION PIN contact assembly requires an arbor-style bench tool with a capacity of 40 lb [178 N] per contact, a support fixture, contact applicator, carrier removal tool and housing assembly tool. Tooling Typical procedure is to place a PC board on the support fixture, insert contact combs into the printed circuit board with the contact applicator and seat with the arbor tool. Next, remove the carrier strip from the contact combs with the carrier break-off tool. Place the housing over the contacts with the housing assembly tool, and repeat the entire process until the board is complete. .100 x .100 [2.54 x 2.54] Centerline Connectors No. of Dual Positions 50 80 100 110 115 120 125 140 175 T-Bar Applicator 266267-4 266267-3 266267-4 266267-5 266267-5 266267-5 266267-4 266267-4 266267-5 Carrier Removal Tool 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 Housing Assembly Tool 313136-1 313136-2 Housing Removal Tool Wing Removal/ Replacement Tool Housing Insertion Tool 313256-1 266233-1 266264-1 Housing Removal Tool Wing Removal/ Replacement Tool Housing Insertion Tool 313256-1 266233-1 266264-1 Contact Replacement Tools With Housing Without Housing 313136-3 266235-1 3-265871-2 313136-4 313136-5 .125 x .125 [3.18 x 3.18] Centerline Connectors No. of Dual Positions 40 52 56 60 72 84 112 124 140 T-Bar Applicator 313139-1 313139-2 313139-2 313139-2 313139-3 313139-2 313139-2 313139-2 313139-2 Carrier Removal Tool 265924-4 265924-6 265924-6 265924-7 265924-4 265924-5 265924-7 265924-5 265924-5 Housing Assembly Tool 313136-1 Contact Replacement Tools With Housing Without Housing 313136-2 313136-3 266235-1 3-265871-2 313136-4 313136-5 95 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors (Continued) Special Application Use Linear and Rotary ZIF Connectors as Card Guides to access more sides of the Daughter Board. Standard Edge II (pages 15 thru 27) or AMP PACE Connectors (pages 98 thru 115) 96 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967