7-2150150-7

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION PART NUMBER REVISION 4 3 2 LOC DESCRIPTION H FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2150150-1 H MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2150150-2 J 7- 2150150 -7 A FINE CRIMP HEIGHT ADJUST 1 REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER FEED TYPE 2150150 -1 2150150 -2 J 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD F ECR-18-016007 09OCT2018 TB TE G ECR-19-007056 02MAY2019 TB TE H ECR-20-002803 26FEB2020 JWC GB J ECR-20-014399 12OCT2020 FJ TE PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE NOSE APPLICATOR DATA SIZE TYPE O O 1.57 mm [.062] 1.57 mm [.062] APPLICATOR INSTRUCTIONS 408-35043 TE TERMINAL TERMINAL DATA: CIRCULAR WIRE PIN TERMINAL NAME: WIRE STRIP LENGTH 7.54-8.33 mm [.297-.328 IN] C TERMINAL APPLICATION SPECIFICATION 926933-1 926933-2 WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 8 1 2 B INSULATION DIAMETER RANGE NONE - - TERMINALS APPLIED TE TERMINAL TE CRIMP SPECIFICATION C1__DWG_PN_1_0 - - 9 WIRE CRIMP ADJUST WITH ITEM 244 - TE TERMINAL 926933-3 926933-4 C1__DWG_PN_1_1 C1__DWG_PN_1_2 C1__DWG_PN_2_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 TE TERMINAL 926933-6 926933-7 WIRE CRIMP HEIGHT mm [INCH] 7 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 TE TERMINAL C1__DWG_PN_3_0 C1__DWG_PN_3_2 9 1.55+/-0.05 [.061+/-.002] 1.45+/-0.05 [.057+/-.002] 1.14+/-0.05 [.045+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 C1__DWG_PN_4_2 8 7 12 4 W1__FA_SETTING_1 W1__FA_SETTING_2 1.76+/-0.05 [.069+/-.002] 1.65+/-0.05 [.065+/-.002] 1.55+/-0.05 [.061+/-.002] 9 NOSE CRIMP HEIGHT REFERENCE SETTING 5.1 4 6.2 7.6 REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. TERMINAL LUBRICANT IS RECOMMENDED. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 10 NOSE CRIMP HEIGHT 5 RECOMMENDED SPARE PARTS CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 9 1 C1__DWG_PN_4_1 WIRE CRIMP HEIGHT REFERENCE SETTING 4 8 3 C1__DWG_PN_4_0 926933-8 926933-9 C1__DWG_PN_3_1 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 7 9 NOSE CRIMP ADJUST WITH WIRE CRIMP HEIGHT ADJUST DIAL 5 3 5 7 - CRIMP HEIGHTS FOR WIRE BARRELS ONLY. ADJUST ITEM 244 TO OBTAIN WIRE CRIMP HEIGHT. WIRE SIZE APPLIES ONLY FOR HANDBRAKE CONTACT REFER TO BMW DRAWING 6 928 203. *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 10 ITEM 244 ADJUSTS WIRE CRIMP HEIGHT. THE WIRE CRIMP HEIGHT ADJUST DIAL ADJUSTS INSULATION (NOSE) CRIMP HEIGHT. POSITION ITEM 27 IN FRONT OF ITEM 77. 1 1 1 1 A 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2 2 2 2 2 1 1 1 1 1 - 1 3 3 3 3 2 2 2 2 2 2 2 2 1 1 1 2 1 2 1 - 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 7 7 7 7 2 2 2 2 2 2 2 2 1 1 1 1 2 2 2 2 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2 4 4 4 4 1 1 1 1 2 2 2 2 1 2 2 1 1 1 1 1 1 1 2 2 1 1 1 2 2 1 1 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 & 4 of 4) MATERIAL - 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 2 1 3 2 2 1 3 1 1 1 1 1 7 2 2 1 2 1 1 2 1 2 4 1 2 1 1 1 1 2119641-1 2119082-2 2079764-1 2119083-1 2119580-1 2844940-3 1803071-1 3-459722-7 994970-2 2119955-2 455888-4 1803203-2 2119791-9 1803607-4 2-18032-2 2119740-1 2168078-1 2168400-8 5-18022-5 2063961-1 2168400-4 5018030-1 986965-8 2063961-9 18023-9 2119652-1 2119653-1 3-2119655-1 1803517-1 1803602-1 1-18028-2 1-2168083-2 2168083-2 690455-1 1-2168083-5 1752371-5 240825-1 2-22281-3 1803292-4 1901259-4 1-2079383-1 2-240644-5 6-240645-5 1633342-5 238011-3 5-2119784-6 6-459492-8 -77 -72 -71 -2 -1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. mm 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - PART NO DWN 12JUN2012 CHK 13JUN2012 APVD 13JUN2012 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION PRODUCT SPEC - 248 244 243 242 239 238 196 195 164 84 82 77 73 71 70 67 66 64 59 58 57 54 53 51 49 48 47 46 44 41 33 31 29 27 25 24 23 22 20 18 17 11 10 8 4 3 1 FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL MECHANICAL FEED ASSEMBLY AIR FEED MODULE SPACER,REAR SHEAR STRIP GUIDE BLADE, SHEAR COUNTER, MAGNETIC ASSY, LUBRICATOR, END FEED SPACER, CRIMPER BLOCK, FRONT DEPRESSOR DEPRESSOR, WIRE DOCUMENTATION PACKAGE SCR, SET, FLT PNT, M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SHCS, LOW HEAD, RoHS, M4 X 16 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) FEED FINGER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM ASSEMBLY, EF ATLANTIC SCR, BHSC, RoHS (M8 X 25) WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 25 SCR, SKT HD CAP, RoHS, M4 X 8.0 STRIPPER, FRONT CASTING SCR, SKT HD CAP, RoHS, M4 X 30 PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SCR, BHSC, RoHS (M6 X 12) PLATE, REAR SHEAR SPACER, SHEAR PLATE ANVIL, WIRE BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM CRIMPER, WIRE O Ocean End Feed Applicator - DRAWING NO 2150150 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV J C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - 44 44.61 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - FEED TYPE REF 0.05 MECHANICAL D 44 244 243 RAM SET-UP 3 2 2 A 7 58 82 195 1 C 73 4 239 59 242 1 1 D PNEUMATIC 1 3 C 238 77 41 A 25 54 23 164 SEE DETAIL A 70 64 A 59 51 20 2 57 67 33 66 FEED SPRING SETTING POSITION 18 B B DETAIL A CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 29 47 A 248 48 33 27 10 46 31 1 8 10 11 1 196 17 53 33 22 24 84 5 49 49 A 49 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 40mm STROKE MECHANICAL PRE FEED 40mm STROKE 11 AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 12JUN2012 CHK 13JUN2012 APVD 13JUN2012 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150150 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV J 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION REVISION DESCRIPTION FEED TYPE 2- 2150150 -1 H FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2150150 -7 A CRIMP TOOLING KIT - J 4 3 2 LOC PART NUMBER 2- 2150150 -2 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 FINE CRIMP HEIGHT ADJUST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE NOSE APPLICATOR DATA SIZE TYPE O O 1.57 mm [.062] 1.57 mm [.062] APPLICATOR INSTRUCTIONS 408-35043 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION CIRCULAR WIRE PIN TERMINAL NAME: WIRE STRIP LENGTH INSULATION DIAMETER RANGE 7.54-8.33 mm [.297-.328 IN] C TERMINAL APPLICATION SPECIFICATION TERMINALS APPLIED TE TERMINAL 926933-1 926933-2 WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 8 1 2 B 3 4 5 C1__DWG_PN_1_0 NONE - - - - 7 - 3 - 9 WIRE CRIMP ADJUST WITH ITEM 244 5 TE TERMINAL 926933-3 926933-4 C1__DWG_PN_1_1 C1__DWG_PN_1_2 C1__DWG_PN_2_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 TE TERMINAL 926933-6 926933-7 TE TERMINAL C1__DWG_PN_3_0 C1__DWG_PN_3_2 WIRE CRIMP HEIGHT mm [INCH] 7 9 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.55+/-0.05 [.061+/-.002] 1.45+/-0.05 [.057+/-.002] 1.14+/-0.05 [.045+/-.002] C1__DWG_PN_4_1 C1__DWG_PN_4_2 WIRE CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 8 7 12 8 9 10 NOSE CRIMP HEIGHT 4 W1__FA_SETTING_1 W1__FA_SETTING_2 1.76+/-0.05 [.069+/-.002] 1.65+/-0.05 [.065+/-.002] 1.55+/-0.05 [.061+/-.002] 9 NOSE CRIMP HEIGHT REFERENCE SETTING 5.1 5 4 6.2 7.6 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. TERMINAL LUBRICANT IS RECOMMENDED. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 7 1 C1__DWG_PN_4_0 926933-8 926933-9 C1__DWG_PN_3_1 9 NOSE CRIMP ADJUST WITH WIRE CRIMP HEIGHT ADJUST DIAL CRIMP HEIGHTS FOR WIRE BARRELS ONLY. ADJUST ITEM 244 TO OBTAIN WIRE CRIMP HEIGHT. WIRE SIZE APPLIES ONLY FOR HANDBRAKE CONTACT REFER TO BMW DRAWING 6 928 203. *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 10 ITEM 244 ADJUSTS WIRE CRIMP HEIGHT. THE WIRE CRIMP HEIGHT ADJUST DIAL ADJUSTS INSULATION (NOSE) CRIMP HEIGHT. POSITION ITEM 27 IN FRONT OF ITEM 77. 1 1 1 1 A - 1 1 - 1 1 - 1 1 - - 1 - 1 - 1 1 - 1 1 - 4 4 - REF REF - 1 - - 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 2 2 - 1 1 - 2 2 - 2 2 - 1 1 - - 1 - 3 3 - 2 2 - 2 2 - 1 - 1 2 - - 1 - 1 1 - 7 7 - 2 2 - 2 2 - 1 1 - 2 2 - 1 1 - 1 1 - 2 2 - 1 1 - 2 2 - 1 1 - 2 2 1 1 1 - 1 1 1 1 1 1 1 1 2119082-2 2079764-1 2119083-1 2119580-1 2844940-3 1803071-1 3-459722-7 2079383-9 994970-2 2119641-2 2119653-2 3-2119655-2 1803518-1 2119955-2 455888-4 1803203-2 2119791-9 1803607-4 2-18032-2 2119740-1 2168078-1 2168400-8 5-18022-5 2063961-1 2168400-4 5018030-1 986965-8 2063961-9 18023-9 2119652-1 1803602-1 1-18028-2 1-2168083-2 2168083-2 690455-1 1-2168083-5 1752371-5 240825-1 2-22281-3 1803292-4 1901259-4 2-240644-5 6-240645-5 1633342-5 238011-3 5-2119784-6 6-459492-8 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 2 1 2 2 2 1 3 2 2 1 3 1 1 7 2 2 1 2 1 1 2 1 2 1 2 1 1 1 1 -77 -22 -21 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 12JUN2012 CHK 13JUN2012 APVD 13JUN2012 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION PRODUCT SPEC - 244 243 242 239 238 196 195 186 164 152 142 141 140 84 82 77 73 71 70 67 66 64 59 58 57 54 53 51 49 48 41 33 31 29 27 25 24 23 22 20 18 11 10 8 4 3 1 CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL MECHANICAL FEED ASSEMBLY AIR FEED MODULE SPACER,REAR SHEAR STRIP GUIDE BLADE, SHEAR SCR, BHSC, RoHS (M6 X 20) COUNTER, MAGNETIC FEED CAM, AIR FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM ASSEMBLY, EF PACIFIC ASSY, LUBRICATOR, END FEED SPACER, CRIMPER BLOCK, FRONT DEPRESSOR DEPRESSOR, WIRE DOCUMENTATION PACKAGE SCR, SET, FLT PNT, M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SHCS, LOW HEAD, RoHS, M4 X 16 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) FEED FINGER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 25 SCR, SKT HD CAP, RoHS, M4 X 8.0 STRIPPER, FRONT CASTING SCR, SKT HD CAP, RoHS, M4 X 30 PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP PLATE, REAR SHEAR SPACER, SHEAR PLATE ANVIL, WIRE BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM CRIMPER, WIRE O Ocean End Feed Applicator - DRAWING NO 2150150 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV J C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION SEE SHEET 1 - 35.58 DWN APVD - - - FEED TYPE 140 REF 0.05 DATE MECHANICAL D 140 RAM SET-UP 244 2 7 2 A 59 243 3 D 239 242 58 82 1 1 1 C 73 PNEUMATIC 195 1 C 3 4 238 77 41 A 25 59 SEE DETAIL A 70 64 54 A 23 2 20 57 67 164 51 FEED SPRING SETTING POSITION 33 66 18 B B DETAIL A CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 142 152 29 48 33 27 10 141 31 1 8 10 11 1 196 186 53 33 22 24 84 5 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 PACIFIC VERSION 49 MECHANICAL PRE FEED 11 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 12JUN2012 CHK 13JUN2012 APVD 13JUN2012 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150150 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV J