7-2150421-7

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION PART NUMBER 4 3 2 LOC REVISION DESCRIPTION FEED TYPE 2150421 -1 2150421 -2 B FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2150421-1 B MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2150421-2 B 7- 2150421 -7 A B 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 FINE CRIMP HEIGHT ADJUST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE DWN APVD A RELEASED 25MAR2014 RW GB B ECR-22-129511 14FEB2022 JWC TE PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F F 2.03 mm [.080] 4.57 mm [.180] APPLICATOR INSTRUCTIONS 3 408-35043 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION RECEPTACLE, FASTIN-FASTON, .187 SERIES TERMINAL NAME: WIRE STRIP LENGTH INSULATION DIAMETER RANGE 6.10-5.33 mm [.240-.210 IN] C TERMINAL APPLICATION SPECIFICATION 3.30-2.29 mm [.130-.090 IN] (A)114-2023 - - - - - TERMINALS APPLIED TE TERMINAL 60435-1 WIRE SIZE W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 20 AWG B 2 3 4 5 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 W1__DWG_WGAUGE_3 5 W1__DWG_WGAUGE_4 1.52+/-0.05 [.060+/-.002] 1.32+/-0.05 [.052+/-.002] 1.19+/-0.05 [.047+/-.002] 1.14+/-0.05 [.045+/-.002] C1__DWG_PN_3_0 152368-1 TE TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_3_1 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] 18 AWG 1 152368 C1__DWG_PN_1_1 16 AWG 22 AWG TE TERMINAL C1__DWG_PN_1_0 W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 - 4 W1__FA_SETTING_1 W1__FA_SETTING_2 3 W1__FA_SETTING_3 W1__FA_SETTING_4 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 50. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 22AWG WIRE TO BE USED FOR TERMINAL 60435-1 ONLY. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 1 1 1 A 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 - 1 1 1 1 1 1 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 REF REF REF REF 1 1 2 1 2 1 2 1 1 3 2 2 2 1 1 1 1 1 1 1 7 2 2 1 2 1 1 2 1 2 4 1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 1 1 1 1 1 - 3 1 3 2 3 2 2 2 2 2 2 2 1 2 1 - 1 1 1 - 1 2 1 1 1 2 - 1 1 - 1 1 1 1 1 1 1 1 1 7 1 7 2 7 2 2 2 2 1 2 1 2 1 2 1 2 1 1 1 1 2 1 2 1 2 1 2 1 2 4 2 4 1 4 1 1 1 1 1 1 1 - 1 - 1 - 1 2 1 1 1 1 1 - 1 - 1 - 1 1 1 1 2 1 1 1 2 1 1 1 1 1 2119641-1 2119082-9 2079764-1 2119083-1 2119580-1 2844940-3 1-18028-0 6-993111-6 8-22280-7 1752353-2 1901680-2 994970-2 455888-5 1803607-4 2-18032-2 2119740-1 2168078-1 1901681-5 2168400-5 2168083-2 5-18022-5 2063961-1 2168400-4 1-2168083-0 5018030-1 986965-8 1-5018030-0 2063961-1 1976055-9 18023-9 2119652-1 2119653-1 2119655-5 1803517-1 1803602-1 1-18028-2 2168083-9 1-2168083-0 240639-1 1-2168083-5 1752371-3 240825-4 2-22281-3 1803292-4 1-1901259-0 1-2079383-1 4-240641-9 1752360-1 240833-2 690482-6 4-1803000-5 1-690474-9 240641-3 238011-2 2119582-3 455888-9 1-456405-3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 2 1 2 1 3 2 2 2 1 1 1 3 1 1 1 1 1 7 2 2 1 2 1 1 2 1 2 4 1 1 1 1 1 1 1 1 1 1 1 1 1 -77 -72 -71 -2 -1 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 20FEB2014 CHK 21FEB2014 APVD 21FEB2014 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION PRODUCT SPEC - 248 244 243 242 239 238 192 177 176 175 174 164 82 71 70 67 66 65 64 60 59 58 57 56 54 53 52 51 50 49 48 47 46 44 41 33 31 29 27 25 24 23 22 20 18 17 16 13 11 10 9 8 7 6 5 4 3 2 1 FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL MECHANICAL FEED ASSEMBLY AIR FEED MODULE WASHER, FLAT, REG M8 PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT PNT, M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL SHCS, LOW HEAD, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 FEED FINGER STANDOFF, HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM ASSEMBLY, EF ATLANTIC SCR, BHSC, RoHS (M8 X 25) WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) SCR, SKT HD CAP, RoHS, M4 X 30 PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SCR, BHSC, RoHS (M6 X 12) SPACER SPACER,HOLD-DOWN PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150421 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV B C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - 44 44.61 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - REF FEED TYPE 0.05 MECHANICAL D 44 19.0 50 0.5 3 2 2 56 A 7 59 239 16 244 243 REF 1 242 177 RAM AND HOLDDOWN SET-UP D 58 5 82 1 C PNEUMATIC 1 C 2 3 2 1 2 4 2 41 176 175 70 174 A 54 52 59 20 65 3 238 25 SEE DETAIL A 57 50 2 A 164 64 51 57 33 33 23 18 67 FEED SPRING SETTING POSITION 66 B B DETAIL A CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 29 47 A 33 27 8 1 46 31 13 9 1 11 17 53 33 22 24 248 48 49 49 A 49 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 40mm STROKE MECHANICAL PRE FEED 40mm STROKE 11 AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 20FEB2014 CHK 21FEB2014 APVD 21FEB2014 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150421 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION REVISION DESCRIPTION FEED TYPE 2- 2150421 -1 B FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2150421 -7 A CRIMP TOOLING KIT - B 4 3 2 LOC PART NUMBER 2- 2150421 -2 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 FINE CRIMP HEIGHT ADJUST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F F 2.03 mm [.080] 4.57 mm [.180] APPLICATOR INSTRUCTIONS 3 408-35043 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION RECEPTACLE, FASTIN-FASTON, .187 SERIES TERMINAL NAME: WIRE STRIP LENGTH INSULATION DIAMETER RANGE 6.10-5.33 mm [.240-.210 IN] C TERMINAL APPLICATION SPECIFICATION 3.30-2.29 mm [.130-.090 IN] (A)114-2023 - - - - - TERMINALS APPLIED TE TERMINAL 60435-1 WIRE SIZE 152368 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 W1__DWG_WGAUGE_1 18 AWG W1__DWG_WGAUGE_2 20 AWG W1__DWG_WGAUGE_3 5 W1__DWG_WGAUGE_4 1.52+/-0.05 [.060+/-.002] 1.32+/-0.05 [.052+/-.002] 1.19+/-0.05 [.047+/-.002] 1.14+/-0.05 [.045+/-.002] C1__DWG_PN_3_0 152368-1 TE TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_3_1 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] 16 AWG 22 AWG TE TERMINAL C1__DWG_PN_1_0 W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 - 4 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 W1__FA_SETTING_4 3 B 1 2 3 4 5 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 50. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 22AWG WIRE TO BE USED FOR TERMINAL 60435-1 ONLY. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 1 1 A 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 1 1 1 1 1 1 1 1 REF REF 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 2 2 1 1 2 2 1 1 1 3 3 2 2 2 2 2 2 1 1 1 1 1 1 2 1 1 1 7 7 2 2 2 2 1 1 2 2 1 1 1 1 2 2 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2119082-9 2079764-1 2119083-1 2119580-1 2844940-3 1-18028-0 2079383-9 6-993111-6 8-22280-7 1752353-2 1901680-2 994970-2 2119641-2 2168083-8 2119653-2 2119655-6 1803518-1 455888-5 1803607-4 2-18032-2 2119740-1 2168078-1 1901681-5 2168400-5 5-18022-5 2063961-1 2168400-4 1-2168083-0 5018030-1 986965-8 1-5018030-0 2063961-1 1976055-9 18023-9 2119652-1 1803602-1 1-18028-2 2168083-9 1-2168083-0 240639-1 1-2168083-5 1752371-3 240825-4 2-22281-3 1803292-4 1-1901259-0 4-240641-9 1752360-1 240833-2 690482-6 4-1803000-5 1-690474-9 240641-3 238011-2 2119582-3 455888-9 1-456405-3 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 2 2 1 3 2 2 2 1 1 1 3 1 1 7 2 2 1 2 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 -77 -22 -21 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 20FEB2014 CHK 21FEB2014 APVD 21FEB2014 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION PRODUCT SPEC - 244 243 242 239 238 192 186 177 176 175 174 164 152 144 142 141 140 82 71 70 67 66 65 64 59 58 57 56 54 53 52 51 50 49 48 41 33 31 29 27 25 24 23 22 20 18 16 13 11 10 9 8 7 6 5 4 3 2 1 CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL MECHANICAL FEED ASSEMBLY AIR FEED MODULE WASHER, FLAT, REG M8 SCR, BHSC, RoHS (M6 X 20) PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM ASSEMBLY, EF PACIFIC SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT PNT, M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL SHCS, LOW HEAD, RoHS, M4 X 20 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 FEED FINGER STANDOFF, HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) SCR, SKT HD CAP, RoHS, M4 X 30 PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SPACER SPACER,HOLD-DOWN PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150421 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION SEE SHEET 1 - 35.58 0.05 140 DATE DWN APVD - - - FEED TYPE REF MECHANICAL D 19.0 140 0.5 2 REF 2 59 239 16 243 3 A 7 244 50 56 1 5 242 58 177 RAM AND HOLDDOWN SET-UP PNEUMATIC 82 1 C D 1 C 238 2 3 2 1 2 4 41 2 25 176 175 70 54 174 SEE DETAIL A 52 57 65 3 A 59 51 20 64 A 50 2 164 33 57 23 33 18 67 B FEED SPRING SETTING POSITION B 66 DETAIL A CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 142 152 29 48 33 27 8 1 141 31 13 9 1 11 186 53 33 22 24 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 PACIFIC VERSION 49 MECHANICAL PRE FEED 11 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 20FEB2014 CHK 21FEB2014 APVD 21FEB2014 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150421 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B