7-2151466-7

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION M FINE CRIMP HEIGHT ADJUST MECHANICAL 5-2151466-1 M SEAL STRIPPER CRIMPER TERMINATING UNIT MECHANICAL 5-2151466-2 M 7-2151466-1 M 7-2151466-2 M 7- 2151466 -7 J CRIMP WIRE INSUL FINE CRIMP HEIGHT ADJUST 2 A - F O - TE CRIMP SPECIFICATION WIRE STRIP LENGTH 5.10-5.70 mm [.201-.224 IN] C TERMINAL APPLICATION SPECIFICATION 2-1241418-3 WIRE SIZE 6.00mm2 n 114-18388 - C1__DWG_PN_1_1 1-2327632-3 C1__DWG_PN_1_2 - - - - - - - - C1__DWG_PN_2_0 VW SEAL C1__DWG_PN_3_0 C1__DWG_PN_2_1 2.58+/-0.05 [.102+/-.002] 2.06+/-0.05 [.081+/-.002] TE SEAL 1394512-1 C1__DWG_PN_4_0 357972742C 357973742C W1__DWG_CRIMP_HT_1 5.5 8.3 W1__DWG_CRIMP_HT_3 9.8 - C1__DWG_PN_4_3 - C1__DWG_PN_4_4 - 4 - W1__FA_SETTING_1 8 - C1__DWG_PN_4_2 1572663-1 1572663-2 CRIMP HEIGHT REFERENCE SETTING 6 SEAL INSUALTION DIAMETER RANGE C1__DWG_PN_4_1 1719043-1 C1__DWG_PN_2_2 2.21+/-0.05 [.087+/-.002] W1__DWG_WGAUGE_3 3 3.4-4.3mm [.134-.169 IN] CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 - 6 TE TERMINAL 1-1241418-3 C1__DWG_PN_1_0 5.00mm2 4.00mm2 - TERMINAL INSULATION DIAMETER RANGE TERMINALS APPLIED TE TERMINAL 1241418-4 - AMP MCP 6.3/4.8K RECEPTACLE TERMINAL NAME: - W1__FA_SETTING_2 5 - 1 2 B - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION & STORAGE OF APPLICATOR. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 6 - RECOMMENDED SPARE PARTS 3 5 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - TERMINAL LUBRICANT IS RECOMMENDED. - 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 8 - THIS CRIMP PARAMETER IS PROVIDED TO MEET A CUSTOM AND UNIQUE CUSTOMER IT HAS BEEN EVALUATED AND IS CONDITIONALLY SPECIFIED BY TE CONNECTIVITY. CUSTOMIZED CRIMP PARAMETER IS NOT LISTED AS AN APPROVED APPLICATION WITHIN CONNECTIVITY APPLICATION SPECIFICATION; HOWEVER, IT HAS BEEN VALIDATED TE CONNECTIVITY SPECIFICATIONS 109-18079(TEST GROUP 1) AND 114-18022. TE EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES THAT THE PRODUCT WILL PERFORM REQUIREMENT. THIS A TE ACCORDING TO CONNECTIVITY SIMILARLY 1 1 1 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. A 1 - 1 1 1 1 - 1 1 1 1 1 1 1 REF 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 1 1 - REF 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 2 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 - - 1 1 DATE DWN APVD K1 ECR-20-010237 20JUL2020 FZ RK K2 ECR-21-112514 02SEP2021 JWC TE L ECR-21-120638 12NOV2021 FZ TE M ECR-22-133774 24MAR2022 LG TE 1 2 - 2 1 1 1 1 1 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - 1 1 PART NO 1 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH -1 1 -77 -72 -71 -52 -51 -2 DIMENSIONS: 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 - 1 1 1 1 - 1 1 - 1 1 1 1 - 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - - 1 2 - 1 - 2 1 1 - 4 2 2 - 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - REF REF 1 1 1 1 REF 1 1 - - REF 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 - - - 1 - - 1 1 - - 1 1 - - 1 1803382-4 22278-9 4-18032-3 1803945-4 1803944-1 2-1803583-1 2119641-1 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 1-18028-2 2119955-1 2844908-1 2844907-1 455888-7 1803607-3 2119791-5 2119943-1 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338685-1 2168083-3 2168083-3 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1-1752356-5 1-2079383-3 3-2844962-5 2844992-2 455888-3 1320928-2 2168083-2 1-18028-2 1803013-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1333229-9 3-240641-3 1-2119781-0 238011-2 6-1633996-5 455888-3 8-458141-0 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. AMP 4805 REV 31MAR2000 DESCRIPTION D TYPE TE TERMINAL LTR - - TERMINAL DATA: P PNEUMATIC CRIMP TOOLING KIT APPLICATOR INSTRUCTIONS 408-35042 66 MECHANICAL PNEUMATIC AND CRIMP TOOLING KIT 6.86 mm [.270] REVISIONS DIST PNEUMATIC MECHANICAL AND CRIMP TOOLING KIT 4.07 mm [.160] 1 PNEUMATIC SEAL STRIPPER CRIMPER TERMINATING UNIT SIZE 3 ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER FEED TYPE 2151466 -1 APPLICATOR DATA 4 LOC DESCRIPTION M 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2151466 -2 D 6 - HOLD DOWN, SPRING LOADED SPRING, COMPRESSION SCR, SET, FLT PNT, M3 X 6.0 TONKER SPACER, TONKER APPLICATOR BASIC ASSEMBLY, SF FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 25) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 16AUG2011 CHK 16AUG2011 APVD 16AUG2011 L.ZHANG L.ZHANG S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 1803945-4 1 1803944-1 1 2-1803583-1 1 2119641-1 1 2119082-8 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-7 1 1803607_3 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 4 2168083-3 2 2168083-3 3 18023-9 1 2119652 1 2119653 1 1803583-9_MOD 1 1803515-1 1 1803602-1 1 1-1752356-5 2 1-2079383-3 2 3-2844962-5 1 2844992-2 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 1803013-1 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1333229-9 1 3-240641-3 1 1-2119781-0 1 238011-2 1 6-1633996-5 1 455888-3 1 8-458141-0 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 2 4-18032-3 301 300 299 298 297 292 248 244 243 242 241 239 238 164 119 113 99 98 82 71 70 69 67 66 60 59 57 56 54 53 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 SIMP_22278-9 DESCRIPTION PRODUCT SPEC - 1 1803382-4 Ocean Side Feed Applicator - DRAWING NO 2151466 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV M C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - FEED TYPE MECHANICAL A D 239 5 REF D 59 56 3.8 REF 44 PNEUMATIC 2 57 REF SHEAR DEPRESSOR DETAIL 244 243 A 53 238 301 242 297 299 8 82 SEE DETAIL A 3 7 59 C 2 1 1 70 69 C 2 3 1 56 4 298 TERMINAL SUPPORT LOCATION 28 5 41 44 66 DETAIL A 2 164 33 B 67 A 24 57 43.79 5 RAM SET-UP 19 9 1 12 ITEM 30 LOCATED AT REAR HOLES 241 13 CAM POSITIONS 30mm STROKE 30mm STROKE 113 6 46 292 98 99 34 54 8 1 60 54 10 1 119 29 1 30 REF REF 11 248 48 B 20 29 30mm STROKE REF 0.05 21 30 47 0.5 34 REF 300 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 3.2 REF FEED TRACK POSITION GUIDE BY WIRE BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16AUG2011 CHK 16AUG2011 APVD 16AUG2011 L.ZHANG L.ZHANG S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151466 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV M 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151466 -1 M FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151466 -7 J CRIMP TOOLING KIT - M 3 2 LOC PART NUMBER 2- 2151466 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 4.07 mm [.160] 6.86 mm [.270] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH 5.10-5.70 mm [.201-.224 IN] TERMINAL APPLICATION SPECIFICATION - TERMINALS APPLIED TE TERMINAL 1241418-4 2-1241418-3 114-18388 1-1241418-3 1-2327632-3 C1__DWG_PN_1_1 C1__DWG_PN_1_2 - - - C1__DWG_PN_2_0 VW SEAL C1__DWG_PN_3_0 C1__DWG_PN_2_2 357972742C 6.00mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 5.00mm2 4.00mm2 2.58+/-0.05 [.102+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 8.3 2.21+/-0.05 [.087+/-.002] W1__DWG_WGAUGE_3 2.06+/-0.05 [.081+/-.002] 5.5 W1__DWG_CRIMP_HT_3 9.8 8 - 3 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 5 6 8 THIS CRIMP PARAMETER IS PROVIDED TO MEET A CUSTOM AND UNIQUE CUSTOMER IT HAS BEEN EVALUATED AND IS CONDITIONALLY SPECIFIED BY TE CONNECTIVITY. CUSTOMIZED CRIMP PARAMETER IS NOT LISTED AS AN APPROVED APPLICATION WITHIN CONNECTIVITY APPLICATION SPECIFICATION; HOWEVER, IT HAS BEEN VALIDATED TE CONNECTIVITY SPECIFICATIONS 109-18079(TEST GROUP 1) AND 114-18022. TE EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES THAT THE PRODUCT WILL PERFORM A 1 1 1 1 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 1 - 1 1 1 1 - 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - HOLD DOWN, SPRING LOADED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 25) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -22 -21 PACIFIC VERSION AMP 4805 REV 31MAR2000 1 1 - Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 1 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 2 - - 1 2 1 - 1 1 2 - 1 1 1 - REQUIREMENT. THIS A TE ACCORDING TO CONNECTIVITY SIMILARLY 1 1 - 1 2 1 - 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 2 - TERMINAL LUBRICANT IS RECOMMENDED. 1 1 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 1 - B 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION & STORAGE OF APPLICATOR. 1 1 - 2 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - 5 1 1 - W1__FA_SETTING_2 1 1 - W1__FA_SETTING_1 1 1 - 4 1 1 6 4 - - C1__DWG_PN_4_4 1 4 - C1__DWG_PN_4_3 - 1 - C1__DWG_PN_4_2 1572663-2 1 - C1__DWG_PN_4_1 1572663-1 357973742C WIRE SIZE TE SEAL - REF REF - 1394512-1 1719043-1 C1__DWG_PN_2_1 1 1 - C1__DWG_PN_4_0 1 - - SEAL INSUALTION DIAMETER RANGE 1 1 - 6 TE TERMINAL C1__DWG_PN_1_0 - 1 1 - 3.4-4.3mm [.134-.169 IN] 1 1 - 3 1803382-4 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2119955-1 2844908-1 2844907-1 455888-7 1803607-3 2119791-5 2119943-1 2119740-1 2168078-1 5-18022-5 985575-3 1338685-1 2168083-3 18023-9 2119652-1 1803602-1 1-1752356-5 1-2079383-3 3-2844962-5 2844992-2 455888-3 1320928-2 2168083-2 1-18028-2 1803013-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1333229-9 3-240641-3 1-2119781-0 238011-2 6-1633996-5 455888-3 8-458141-0 1 1 - TERMINAL INSULATION DIAMETER RANGE n 1 - AMP MCP 6.3/4.8K RECEPTACLE TERMINAL NAME: C - DWN 16AUG2011 CHK 16AUG2011 APVD 16AUG2011 L.ZHANG L.ZHANG S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0_MOD 1 1803516-1 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-7 1 1803607_3 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338685-1 2 2168083-3 3 18023-9 1 2119652 1 1803602-1 1 1-1752356-5 2 1-2079383-3 2 3-2844962-5 1 2844992-2 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 1803013-1 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1333229-9 1 3-240641-3 1 1-2119781-0 1 238011-2 1 6-1633996-5 1 455888-3 1 8-458141-0 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764_APP 301 244 243 242 241 239 238 164 151 144 143 142 141 140 119 113 99 98 82 71 70 69 67 66 59 57 56 53 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-8 DESCRIPTION PRODUCT SPEC - 1 1803382-4 Ocean Side Feed Applicator - DRAWING NO 2151466 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV M C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D REF 5 239 140 59 2 244 56 PNEUMATIC D 3.8 REF 57 243 242 REF SHEAR DEPRESSOR DETAIL 2 3 53 A 3.2 301 238 REF 8 7 34 59 REF TERMINAL SUPPORT LOCATION 82 1 C SEE DETAIL A 0.5 1 C 70 69 56 2 3 1 4 28 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 5 41 34.76 140 0.05 REF 66 DETAIL A 2 164 RAM SET-UP 67 57 33 A 24 B 5 B 21 30 20 29 9 19 1 12 ITEM 30 LOCATED AT REAR HOLES 241 CAM POSITIONS 30mm STROKE 13 1 REF REF 29 30mm STROKE 30mm STROKE 142 30 151 113 48 6 141 98 99 34 143 8 1 144 143 10 1 119 FEED TRACK POSITION GUIDE BY WIRE BARREL 11 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16AUG2011 CHK 16AUG2011 APVD 16AUG2011 L.ZHANG L.ZHANG S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151466 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV M