7724E2664-9CS1996

7724E2664 SPECIFICATION CONTROL DRAWING 77 OHM, AWG 24, 19 STRANDS OF AWG 36, DATA BUS CABLE, OUTER SPACE USE CHEMINAX Date: Revision: 8-8-18 E THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE DESIGNATED. .0250 .052 ± .002 .111 .127 (nominal) .135 (maximum) ELECTRICAL CHARACTERISTICS CHARACTERISTIC IMPEDANCE MUTUAL CAPACITANCE ATTENUATION 77 ± 7 ohms, Method C at 1 MHz 30.0 pF/ft. (maximum) 1.0 dB/100 ft. (nominal) at 1 MHz 8.0 dB/100 ft. (maximum) at 10 MHz SURFACE TRANSFER IMPEDANCE 70 milliohms/meter (nominal) at 10 MHz CONDUCTORS AWG 24, 19 Strands of AWG 36, Silver-Coated HighStrength Copper Alloy DIELECTRICS Radiation-Crosslinked, Modified ETFE Colors - Light Blue/White SHIELD - Flat .0015 Strand Thickness, Silver-Coated Copper JACKET Radiation-Crosslinked, Modified ETFE ADDITIONAL REQUIREMENTS COMPONENT WIRE PRIOR TO CABLING (Test procedures per SAE AS22759) CONDUCTOR RESISTANCE CROSSLINKING PROOF TEST INSULATION (DIELECTRIC) ELONGATION TENSILE STRENGTH INSULATION FLAWS SPARK TEST IMPULSE TEST INSULATION RESISTANCE LOW TEMPERATURE-COLD BEND SHRINKAGE 26.5 ohms/1000 ft. (nominal) 300 ± 3°C for 1 hour, .500 inch mandrel, .500 lb, 2.5 kV dielectric test 50% (minimum) 5000 lbf/in2 (minimum) 3.0 kV (rms) 8.0 kV (peak) 5000 megohms for 1000 ft. (minimum) -65 ± 3°C for 4 hours, .500 inch mandrel, 1.00 lb, 2.5 kV dielectric test 200 ± 3°C for 1 hour, .125 inch (maximum) in 12 inches FINISHED CABLE (Test procedures per NEMA WC 27500, unless otherwise specified) BLOCKING 200°C for 6 hours CABLE LAY LENGTH .75 inch (minimum), 1.25 inches (maximum) CROSSLINKED VERIFICATION 300 ± 5°C for 6 hours, 6.00 inch mandrel FLAMMABILITY 3 seconds (maximum), 3 inches (maximum); (Method B of Spec 1200) no flaming of facial tissue JACKET ELONGATION 50% (minimum) TENSILE STRENGTH 5000 lbf/in2 (minimum) JACKET FLAWS SPARK TEST 1.0 kV (rms) IMPULSE TEST 6.0 kV (peak) JACKET THICKNESS .008 inch (nominal) LOW TEMPERATURE-COLD BEND -55 ± 5°C for 4 hours, 6.00 inch mandrel SHIELD COVERAGE 90% (minimum) VOLTAGE WITHSTAND 1000 volts (rms) (minimum) (DIELECTRIC) WEIGHT 10.4 lbs/1000 ft. (nominal) OUTER SPACE REQUIREMENTS RADIATION RESISTANCE VACUUM STABILITY Designate outer jacket color with a dash number in accordance TOTAL MASS LOSS (TML) with MIL-STD-681. Unless otherwise specified, outer jacket color VOLATILE CONDENSABLE will be white designated by a "-9" appended to the part number, MATERIAL (VCM) e.g. 7724E2664-9. WEIGHT LOSS 500 megarads/3.75 inch mandrel 1.00% (maximum) 0.10% (maximum) Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. 200°C (maximum) 0.45% (maximum) ENGINEERING REFERENCE TEMPERATURE RATING Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. TE Connectivity also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Cheminax, Raychem, TE Connectivity, and TE connectivity (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue Redwood City, California 94063-3800 Phone: 1-800-522-6752 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2006-2018 TE Connectivity Ltd. family of companies. All Rights Reserved.