7726D0664-96

7726D0664 SPECIFICATION CONTROL DRAWING CHEMINAX 77 OHM, AWG 26, 19 STRANDS OF AWG 38, OPTIMIZED SHIELD, DATA BUS CABLE, MIL-STD-1553 Date: 7-10-14 Revision: D THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS ELECTRICAL CHARACTERISTICS DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE CHARACTERISTIC IMPEDANCE DESIGNATED. .0200 .037 .025 .091 CONDUCTORS AWG 26, 19 Strands of AWG 38, Silver-Coated HighStrength Copper Alloy MUTUAL CAPACITANCE 30.0 pF/ft. (maximum) ATTENUATION 1.5 dB/100 ft. (maximum) at 1 MHz SURFACE TRANSFER IMPEDANCE 50 milliohms/meter (maximum) at 0.1 MHz (Curve defined by the 50 milliohms/meter (maximum) at 1 MHz following points) 100 milliohms/meter (maximum) at 10 MHz ADDITIONAL REQUIREMENTS DIELECTRICS Radiation-Crosslinked, Modified ETFE Colors - Light Blue/White FILLERS Radiation-Crosslinked, Modified ETFE SHIELD AWG 38, Tin-Coated Copper, Optimized 77 ± 5 ohms, Method C at 1 MHz COMPONENT WIRE PRIOR TO CABLING (Test procedures per SAE AS22759) CONDUCTOR RESISTANCE 42.0 ohms/1000 ft. (nominal) CROSSLINKING PROOF TEST 300 ± 3°C for 1 hour, .500 inch mandrel, .250 lb, 2.5 kV dielectric test INSULATION (DIELECTRIC) ELONGATION TENSILE STRENGTH 50% (minimum) 5000 lbf/in2 (minimum) INSULATION FLAWS SPARK TEST IMPULSE TEST 3.0 kV (rms) 8.0 kV (peak) INSULATION RESISTANCE 5000 megohms for 1000 ft. (minimum) LOW TEMPERATURE-COLD BEND -65 ± 3°C for 4 hours, .500 inch mandrel, .500 lb, 2.5 kV dielectric test SHRINKAGE 200 ± 3°C for 1 hour, .125 inch (maximum) in 12 inches FINISHED CABLE (Test procedures per NEMA WC 27500, unless otherwise specified) BLOCKING .107 JACKET Radiation-Crosslinked, Modified ETFE 200°C for 6 hours CABLE LAY LENGTH .75 inch (minimum), 1.25 inches (maximum) CROSSLINKED VERIFICATION 300 ± 5°C for 6 hours, 3.00 inch mandrel FLAMMABILITY (Method B of Spec 1200) 3 seconds (maximum); 3 inches (maximum); no flaming of facial tissue JACKET ELONGATION TENSILE STRENGTH 50% (minimum) 5000 lbf/in2 (minimum) JACKET FLAWS SPARK TEST IMPULSE TEST 1.0 kV (rms) 6.0 kV (peak) JACKET THICKNESS .008 inch (nominal) LOW TEMPERATURE-COLD BEND -55 ± 5°C for 4 hours, 3.00 inch mandrel VOLTAGE WITHSTAND (DIELECTRIC) 1500 volts (rms) Designate outer jacket color with a dash number in accordance with MIL-STD-681. Unless otherwise specified, outer jacket color will be WEIGHT white (designated by a "-9" appended to the part number, e.g. 7726D0664-9). ENGINEERING REFERENCE Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the TEMPERATURE RATING purchase order. 10.6 lbs/1000 ft. (nominal) 150°C (maximum) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Cheminax, Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue Redwood City, California 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2014 Tyco Electronics Corporation. All rights reserved.