8-2150072-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2150072 -1 2150072 -2 B FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2150072-1 B MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2150072-2 C 7- 2150072 -7 A C 4 3 2 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST SET UP GAUGE 2119599-2 ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER LOC A 1 REVISIONS DIST 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD 1 DEVELOPMENT 16JAN2013 YY SX A RELEASED 12APR2013 YY UG B ECR-18-015273 25SEP2018 TB TE C ECR-22-130891 28FEB2022 TB RK PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE 3 F F 1.40 mm [.055] 2.03 mm [.080] APPL INSTRUCTIONS 408-10390 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION .187 SERIES RECEPTACLE FASTON TERMINAL NAME: WIRE STRIP LENGTH n 4.40-5.16 mm [.173-.203 IN] C TERMINAL APPLICATION SPECIFICATION 114-2036 - TERMINALS APPLIED TE TERMINAL 342368-1 342368-2 WIRE SIZE 20 AWG 22 AWG 24 AWG 1 B 2 3 4 5 60573-1 60573-2 C1__DWG_PN_1_1 C1__DWG_PN_1_2 INSULATION DIAMETER RANGE 1.02-1.78 mm [.040-.070 IN] - - - - 5 TE TERMINAL C1__DWG_PN_1_0 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_2_2 62181-1 62187-2 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.22+/-0.05 [.048+/-.002] 1.09+/-0.05 [.043+/-.002] 1.02+/-0.05 [.040+/-.002] C1__DWG_PN_3_0 TE TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_3_1 C1__DWG_PN_3_2 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 5 W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 4.8 6.4 7.2 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 4 W1__FA_SETTING_1 3 W1__FA_SETTING_2 W1__FA_SETTING_3 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. TERMINAL LUBRICANT IS RECOMMENDED. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 1 1 1 1 A 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 - 1 3 3 3 3 2 2 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 - 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 7 7 7 7 2 2 2 2 2 2 2 2 1 1 1 1 2 2 2 2 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2 4 4 4 4 1 1 1 1 1 1 1 1 - 1 1 1 1 1 2 2 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 2 2 1 1 2119641-1 2119082-8 2079764-1 2119083-1 2119580-1 2844940-3 1-18028-0 6-993111-6 8-22280-7 1752353-2 1901680-2 994970-2 2119955-2 455888-5 2119791-9 1803607-4 2-18032-2 2119740-1 2168078-1 1-1901681-8 2168400-8 2168083-2 5-18022-5 2063961-1 2168400-4 2168083-2 5018030-1 986965-8 1-5018030-0 2063961-9 1-1752354-1 18023-9 2119652-1 2119653-1 2119655-5 1803517-1 1803602-1 1-18028-2 2168083-9 2168083-2 240639-3 1-2168083-5 1-1752371-2 240825-9 2-22281-3 1803292-4 1901259-3 1-2079383-1 4-240641-9 240644-5 4-690495-7 1333213-4 4-690474-1 240641-5 238011-7 6-1633961-5 455888-3 1-456402-6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 2 1 2 1 3 2 2 2 1 1 1 3 1 1 1 1 1 7 2 2 1 2 1 1 2 1 2 4 1 1 1 1 1 1 1 1 1 1 1 1 -77 -72 -71 -2 -1 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16JAN2012 CHK 16JAN2012 APVD 16JAN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION PRODUCT SPEC - 248 244 243 242 239 238 192 177 176 175 174 164 84 82 73 71 70 67 66 65 64 60 59 58 57 56 54 53 52 51 50 49 48 47 46 44 41 33 31 29 27 25 24 23 22 20 18 17 16 11 10 9 8 7 6 5 4 3 2 1 FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL MECHANICAL FEED ASSEMBLY AIR FEED MODULE WASHER, FLAT, REG M8 PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC ASSY, LUBRICATOR, END FEED SPACER, CRIMPER DEPRESSOR, WIRE DOCUMENTATION PACKAGE SCR, SET, FLT PNT, M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL SHCS, LOW HEAD, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 8.0 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 FEED FINGER STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM ASSEMBLY, EF ATLANTIC SCR, BHSC, RoHS (M8 X 25) WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 8.0 STRIPPER (MACHINING) SCR, SKT HD CAP, RoHS, M4 X 30 PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SCR, BHSC, RoHS (M6 X 12) SPACER PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION BLADE, SLUG SPACER BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150072 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - 44 44.61 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - FEED TYPE REF 0.05 MECHANICAL D 16.3 0.5 1 44 243 50 D 3 REF 2 244 56 A 7 2 5 58 177 242 RAM AND HOLDDOWN SET-UP 82 1 C 239 59 16 PNEUMATIC 1 C 2 73 3 41 192 4 238 1 176 2 A 175 2 2 64 174 52 3 164 SEE DETAIL A 70 23 65 50 59 25 A 2 51 54 20 67 57 FEED SPRING SETTING POSITION 33 66 18 B B DETAIL A CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 29 47 A 248 48 33 27 8 1 60 46 31 9 11 1 17 53 33 22 24 84 5 49 49 A 49 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 40mm STROKE MECHANICAL PRE FEED 40mm STROKE 11 AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16JAN2012 CHK 16JAN2012 APVD 16JAN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150072 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV C 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2150072 -1 B FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2150072 -7 A CRIMP TOOLING KIT - 2- 2150072 -2 C 4 3 2 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST SET UP GAUGE 2119599-2 PACIFIC VERSION TERMINATOR INTERFACE ADAPTER LOC A 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE 3 F F 1.40 mm [.055] 2.03 mm [.080] APPL INSTRUCTIONS 408-10390 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION .187 SERIES RECEPTACLE FASTON TERMINAL NAME: WIRE STRIP LENGTH n 4.40-5.16 mm [.173-.203 IN] C TERMINAL APPLICATION SPECIFICATION 114-2036 - TERMINALS APPLIED TE TERMINAL 342368-1 342368-2 WIRE SIZE 20 AWG 22 AWG 24 AWG B 1 2 3 4 5 60573-1 60573-2 C1__DWG_PN_1_1 C1__DWG_PN_1_2 1.02-1.78 mm [.040-.070 IN] - - - - C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_2_2 62181-1 62187-2 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.22+/-0.05 [.048+/-.002] 1.09+/-0.05 [.043+/-.002] 1.02+/-0.05 [.040+/-.002] C1__DWG_PN_3_0 TE TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_3_1 C1__DWG_PN_3_2 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 5 5 TE TERMINAL C1__DWG_PN_1_0 INSULATION DIAMETER RANGE W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 4.8 6.4 7.2 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 4 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 3 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. TERMINAL LUBRICANT IS RECOMMENDED. 1 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 1 1 1 A - 1 1 - 1 1 - 1 1 - - 1 - 1 - 1 1 - 4 4 - 1 1 - 1 1 - 1 1 - 1 1 - REF REF - 1 - 1 1 - - 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 2 2 - 1 1 - 2 2 - 1 1 - 2 2 - 1 1 - - 1 - 3 3 - 2 2 - 2 2 - 2 2 - 1 1 - 1 - 1 1 - 1 2 - - 1 - 1 1 - 7 7 - 2 2 - 2 2 - 1 1 - 2 2 - 1 1 - 1 1 - 2 2 - 1 1 - 2 2 - 1 1 - 1 1 - - - 1 1 1 1 1 - 1 1 - - - 1 1 - 1 1 1 1 1 - 1 1 1 1 1 2119082-8 2079764-1 2119083-1 2119580-1 2844940-3 1-18028-0 2079383-9 6-993111-6 8-22280-7 1752353-2 1901680-2 994970-2 2119641-2 2168083-8 2119653-2 2119655-6 1803518-1 2119955-2 455888-5 2119791-9 1803607-4 2-18032-2 2119740-1 2168078-1 1-1901681-8 2168400-8 5-18022-5 2063961-1 2168400-4 2168083-2 5018030-1 986965-8 1-5018030-0 2063961-9 1-1752354-1 18023-9 2119652-1 1803602-1 1-18028-2 2168083-9 2168083-2 240639-3 1-2168083-5 1-1752371-2 240825-9 2-22281-3 1803292-4 1901259-3 4-240641-9 240644-5 4-690495-7 1333213-4 4-690474-1 240641-5 238011-7 6-1633961-5 455888-3 1-456402-6 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 2 2 1 3 2 2 2 1 1 1 3 1 1 7 2 2 1 2 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 -77 -22 -21 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16JAN2012 CHK 16JAN2012 APVD 16JAN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION PRODUCT SPEC - 244 243 242 239 238 192 186 177 176 175 174 164 152 144 142 141 140 84 82 73 71 70 67 66 65 64 59 58 57 56 54 53 52 51 50 49 48 41 33 31 29 27 25 24 23 22 20 18 16 11 10 9 8 7 6 5 4 3 2 1 CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL MECHANICAL FEED ASSEMBLY AIR FEED MODULE WASHER, FLAT, REG M8 SCR, BHSC, RoHS (M6 X 20) PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM ASSEMBLY, EF PACIFIC ASSY, LUBRICATOR, END FEED SPACER, CRIMPER DEPRESSOR, WIRE DOCUMENTATION PACKAGE SCR, SET, FLT PNT, M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL SHCS, LOW HEAD, RoHS, M4 X 16 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 8.0 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 FEED FINGER STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 8.0 STRIPPER (MACHINING) SCR, SKT HD CAP, RoHS, M4 X 30 PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SPACER PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION BLADE, SLUG SPACER BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150072 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION SEE SHEET 1 - 35.58 0.05 APVD - - - MECHANICAL D 0.5 140 244 50 DWN FEED TYPE 140 REF 16.3 DATE 1 2 7 3 RAM AND HOLDDOWN SET-UP 2 242 177 59 5 C PNEUMATIC 1 C 2 238 73 4 3 239 58 82 1 A 16 243 REF 56 D 2 1 192 2 41 2 176 A 175 174 52 SEE DETAIL A 70 64 51 54 65 3 59 25 A 50 2 164 23 20 67 57 FEED SPRING SETTING POSITION 33 66 18 B B DETAIL A CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 142 152 29 48 33 27 8 1 144 141 31 9 11 1 186 53 33 22 24 84 5 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 PACIFIC VERSION 49 MECHANICAL PRE FEED 11 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16JAN2012 CHK 16JAN2012 APVD 16JAN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150072 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C