8-2150122-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION PART NUMBER A WIRE INSUL 2 SET UP GAUGE 2119599-2 A FINE CRIMP HEIGHT ADJUST 4 NONE CRIMP TOOLING KIT - 2119792-2 SMART APPLICATOR 2161326-1 SERVO LATCH PLATE 2119951-1 SMART APPLICATOR SERVO LATCH PLATE 12 2150122 -7 A PNEUMATIC SERVO LATCH PLATE NON-CRIMP HEIGHT ADJUST 2119950-1 MECHANICAL FEED 4 MECHANICAL FEED PNEUMATIC FEED - APPLICATOR INSTRUCTIONS 2119951-1 - 2119641-1 - TE TERMINAL - 8- 2150122 -4 - - 1901697-1 8- 2150122 -5 - - 1901697-1 2119949-1 2063961-1 2161326-1 - 2119949-1 2119950-1 - - - 2063961-1 2119792-2 - 8- 2150122 -5 - 5-18022-5 2119653-1 8- 2150122 -4 - 5-18022-5 - - - - 2119653-1 2119641-1 - - - - 2168400-7 WIRE STRIP LENGTH n 4.82-5.84 mm [.190-.230 IN] C TERMINAL APPLICATION SPECIFICATION 114-2088 - TERMINALS APPLIED TE TERMINAL 2168400-7 - - (QUANTITY 2) - 2063440-1 - - - 41974 WIRE SIZE 3200 CMA 1000 CMA B CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 - TE TERMINAL C1__DWG_PN_2_0 41975 C1__DWG_PN_1_1 - - 1.42+/-0.05 [.056+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY TE TERMINAL CRIMP HEIGHT REFERENCE SETTING 14 1.73+/-0.05 [.068+/-.002] C1__DWG_PN_3_0 9 W1__FA_SETTING_1 - W1__DWG_CRIMP_HT_2 6 C1__DWG_PN_4_0 - W1__DWG_CRIMP_HT_1 W1__FA_SETTING_2 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2150122 2150122 2150122 2150122 -4 -4 -5 -6 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 6 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 11 A 12 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37. GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 1 & 252. MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. THE ITEM ITEM FEED RECOMMENDED SET-UP FOR END FEED APPLICATORS IS POST-FEED WITH 2119653-1. THE APPLICATOR CAN BE CONFIGURED FOR PRE-FEED WITH 2119652-1 BUT MAY ENCOUNTER PROBLEMS WITH SOME APPLICATIONS. ISSUES OR TERMINAL JAMMING MAY OCCUR IN THE PRE-FEED CONFIGURATION. WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT 13 TERMINAL LUBRICANT IS RECOMMENDED. 14 REFER TO TERMINAL CUSTOMER DRAWING FOR CRIMP HEIGHT FORMULA TO CALCULATE SPECIFIC CRIMP HEIGHTS. AMP 4805 REV 31MAR2000 DATE DWN APVD RELEASED 03JUL2014 LG TE ECR-14-014956 08OCT2014 JH TE - 13 TE TERMINAL C1__DWG_PN_1_0 - DESCRIPTION - INSULATION DIAMETER RANGE - LTR (QUANTITY 2) TE CRIMP SPECIFICATION SPLICE TERMINAL NAME: P 2063440-1 408-10390 TERMINAL DATA: 66 A1 F - - A REVISIONS DIST A TYPE 2.79 mm [.110] LOC 1 PART NUMBERS REQUIRED PNEUMATIC FEED SERVO LATCH PLATE FINE CRIMP HEIGHT ADJUST A 7- 2150122 -7 CONVERT TO MECHANICAL FINE CRIMP HEIGHT ADJUST 2150122 -6 SIZE 3 APPLICATOR STYLE CONVERSION CHART FEED TYPE FINE CRIMP HEIGHT ADJUST A 2150122 -5 CRIMP DESCRIPTION A 2150122 -2 APPLICATOR DATA 4 20 REVISION 2150122 -1 D 5 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 6 1 - - 1 - - - 1 - 1 1 1 - - - - 1 - - - - 1 - - - - 1 - 1 - 1 1 1 - 1 - 1 1 1 - - 1 - - - - 2 2 - - - - - - 1 - - - - 1 - - 1 1 - - - REF REF - - - - - 2 - 1 1 1 1 1 - REF REF REF REF REF - - - - 1 - - - - 1 - - REF REF - - - 1 1 - - 1 1 1 1 1 - 1 1 1 1 1 - 1 1 1 1 1 - 2 2 2 2 2 - 1 - - 1 1 - 2 2 2 2 2 - 2 2 2 2 2 - 1 - 1 1 1 - 3 - 3 3 3 - - - - - 1 - - - - - 1 - 3 3 3 3 3 - 2 2 2 2 2 - 2 2 2 2 2 - 2 2 2 2 2 - - - - 1 - - - - 1 2 - - - - - 1 - - - - - 1 - 1 1 1 1 1 - 1 - 1 1 1 - 1 1 1 1 1 - 1 - 1 1 1 - 1 - 1 1 1 - 1 1 1 1 1 - 1 1 1 1 1 - 1 - 1 1 1 - 7 7 7 7 7 - 2 2 2 2 2 - 2 2 2 2 2 - 1 1 1 1 1 - 2 2 2 2 2 - 1 1 1 1 1 - 1 1 1 1 1 - 2 2 2 2 2 - 1 1 1 1 1 - 2 2 2 2 2 - 4 4 4 4 4 - 1 1 1 1 1 - 2 2 2 2 2 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 - - - - - - - - - - - - - - - - - - - - - - - - - 1 1 1 1 1 1 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2161315-1 2168400-7 2119580-1 2063440-1 2119740-2 1901697-1 21045-3 994969-1 994970-2 240638-1 3-23627-7 SEE NOTE 4 1633743-1 2119955-2 455888-5 2119956-2 2-18032-2 2119740-1 2168078-1 2168400-5 2119793-1 992763-5 5-18022-5 2063961-1 2168400-4 5018030-2 5018030-1 986965-8 2119792-2 18023-9 2119652-1 2119653-1 2119655-5 2161310-1 2079383-7 2119645-1 2119957-1 2119644-1 2119085-1 2119092-1 1-18028-2 2168083-9 1-2168083-0 690455-3 1320906-1 1752371-1 240825-9 2-22281-3 1752373-4 1901259-4 1-2079383-1 240644-1 240645-1 690619-5 4-690618-8 2-459722-7 4-459736-0 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 1 2 2 1 3 1 1 3 2 2 2 1 3 1 1 1 1 1 1 1 1 1 1 7 2 2 1 2 1 1 2 1 2 4 1 2 1 1 1 1 1 1 1 1 1 -77 -7 -6 -5 -2 -1 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 13MAY2014 CHK 13MAY2014 APVD 13MAY2014 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION PRODUCT SPEC - 260 252 250 249 248 247 246 245 240 239 238 213 183 172 166 164 163 137 135 133 84 82 71 70 67 66 64 63 62 59 58 57 55 54 53 51 49 48 47 46 44 41 40 39 38 37 35 33 31 29 27 25 24 23 22 20 18 17 11 10 9 8 7 6 5 4 3 2 1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, STEPPED, AMP STYL, EF, NON-ADJUST SHCS, LOW HEAD, RoHS, M5 X 10 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION FEED FINGER ASSEMBLY,EF RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM ASSY, LUBRICATOR, END FEED SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SHCS, LOW HEAD, RoHS, M4 X 20 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) PAWL, EF, AIR SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM, STEPPED, AMP STYLE, END FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER, FRONT CASTING STUD, THREADED PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SCR, BHSC, RoHS (M6 X 12) PLATE, REAR SHEAR SPACER, SHEAR PLATE PLATE, RETAINING ANVIL, SPLICE TYPE BLADE, SHEAR CRIMPER, WIRE Ocean End Feed Applicator - DRAWING NO 2150122 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 37 6 40 FEED TYPE 62 6 MECHANICAL 38 D 39 247 260 7 246 252 245 35 7 44 D 2 2 A 2 2 239 59 58 8 1 166 63 7 PNEUMATIC 82 C 1 1 C 238 41 249 70 2 54 250 A 137 55 10 164 163 20 2 6 172 57 51 33 A 64 23 67 213 B SERVO LATCH PLATE 84 66 18 B 24 22 25 CAM POSITIONS 33 53 30mm STROKE 30mm STROKE 30mm STROKE 29 47 A 27 46 31 8 1 248 48 33 9 10 1 11 17 4 135 133 183 240 REF 49 49 A 49 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 SERVO FEEDER NOT INCLUDED A 40mm STROKE MECHANICAL PRE FEED 40mm STROKE 11 AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 13MAY2014 CHK 13MAY2014 APVD 13MAY2014 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150122 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER WIRE SIZE 3200 CMA 1000 CMA B - 8- 2150122 -5 MECHANICAL FEED 2119949-1 2063961-1 5-18022-5 2119653-2 8- 2150122 -4 - 2161326-1 - SERVO LATCH PLATE MECHANICAL FEED 2119949-1 2063961-1 5-18022-5 2- 2150122 -7 A FINE CRIMP HEIGHT ADJUST NONE A CRIMP TOOLING KIT - SMART APPLICATOR 4 PNEUMATIC FEED - - 2161326-1 2119950-1 - - - 2119792-2 - - - - - - 2119653-2 2119641-2 - - - 2168400-7 2168400-7 - - - 2063440-1 - - - TE TERMINAL 41975 CRIMP HEIGHT mm [INCH] 1.42+/-0.05 [.056+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY TE TERMINAL CRIMP HEIGHT REFERENCE SETTING 13 1.73+/-0.05 [.068+/-.002] C1__DWG_PN_3_0 W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 - C1__DWG_PN_4_0 6 9 W1__FA_SETTING_1 - W1__FA_SETTING_2 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- 2150122 -4 2150122 -4 2150122 -5 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62. 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 8 9 10 A 1 6 12 13 1 & 153. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 11 THE RECOMMENDED SET-UP FOR END FEED APPLICATORS IS POST-FEED WITH ITEM 2119653-1. THE APPLICATOR CAN BE CONFIGURED FOR PRE-FEED WITH ITEM 2119652-1 BUT MAY ENCOUNTER PROBLEMS WITH SOME APPLICATIONS. FEED ISSUES OR TERMINAL JAMMING MAY OCCUR IN THE PRE-FEED CONFIGURATION. TERMINAL LUBRICANT IS RECOMMENDED. REFER TO TERMINAL CUSTOMER DRAWING FOR CRIMP HEIGHT FORMULA TO CALCULATE SPECIFIC CRIMP HEIGHTS. AMP 4805 REV 31MAR2000 DATE SEE SHEET 1 DWN APVD - - - - 12 C1__DWG_PN_2_0 DESCRIPTION (QUANTITY 2) - - LTR - INSULATION DIAMETER RANGE - P - TE CRIMP SPECIFICATION - 66 (QUANTITY 2) F - n A REVISIONS DIST 2063440-1 TYPE TE TERMINAL W1__DWG_WGAUGE_2 - 1901697-1 FINE CRIMP HEIGHT ADJUST - W1__DWG_WGAUGE_1 8- 2150122 -4 2119951-1 A 114-2088 C1__DWG_PN_1_1 - SERVO LATCH PLATE SMART APPLICATOR LOC 1 - 2119641-2 2- 2150122 -5 4.82-5.84 mm [.190-.230 IN] 41974 SET UP GAUGE 2119599-2 - 8- 2150122 -5 WIRE STRIP LENGTH C1__DWG_PN_1_0 2119792-2 1901697-1 SPLICE TERMINALS APPLIED MECHANICAL 2119950-1 2119951-1 TE TERMINAL TERMINAL APPLICATION SPECIFICATION PNEUMATIC FEED SERVO LATCH PLATE - TERMINAL NAME: 2 PART NUMBERS REQUIRED PNEUMATIC 2.79 mm [.110] TE TERMINAL FINE CRIMP HEIGHT ADJUST CONVERT TO FINE CRIMP HEIGHT ADJUST SIZE TERMINAL DATA: FEED TYPE A APPLICATOR DATA 3 APPLICATOR STYLE CONVERSION CHART 2- 2150122 -2 APPL INSTRUCTIONS 408-10390 C DESCRIPTION A 7- 2150122 -7 WIRE INSUL 4 20 REVISION 2- 2150122 -1 CRIMP 5 ALL RIGHTS RESERVED. PART NUMBER D 6 1 - 1 1 1 1 - - - 1 - - - 1 - 1 1 1 1 - - 2 - - - - - 1 - - - 1 - - 1 - - 4 4 4 4 - - REF - - - - 2 - 1 1 1 1 - REF REF REF REF - - - 1 - 1 1 1 1 - - - 1 - 1 1 1 1 - - - - 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - - 1 - - REF - - - 1 - - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 - 1 1 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - 3 3 3 3 - - - - 1 - - - - 1 - 3 3 3 3 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - - - 1 - - - 1 2 - - - - 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 7 7 7 7 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - - - - - - - - - - - - - - - - - - - - 1 1 1 1 1 2119782-1 2119640-1 2079988-1 1-22279-3 2168400-7 2119580-1 2063440-1 2119740-2 2079383-9 1901697-1 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2119653-2 2119655-6 2161313-1 2119092-2 3-23627-7 SEE NOTE 4 1633743-1 2119955-2 455888-5 2119956-2 2-18032-2 2119740-1 2168078-1 2168400-5 2119793-1 992763-5 5-18022-5 2063961-1 2168400-4 5018030-2 5018030-1 986965-8 2119792-2 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-1 1-18028-2 2168083-9 1-2168083-0 690455-3 1320906-1 1752371-1 240825-9 2-22281-3 1752373-4 1901259-4 240644-1 240645-1 690619-5 4-690618-8 2-459722-7 4-459736-0 1 1 1 1 2 1 1 1 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 3 1 1 3 2 2 2 1 3 1 1 1 1 1 7 2 2 1 2 1 1 2 1 2 1 2 1 1 1 1 1 1 1 1 1 -77 -27 -25 -22 -21 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 13MAY2014 CHK 13MAY2014 APVD 13MAY2014 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION PRODUCT SPEC - 251 250 249 246 240 239 238 213 186 183 172 166 164 163 153 152 145 142 141 140 139 137 135 133 84 82 71 70 67 66 64 63 62 59 58 57 55 54 53 51 49 48 41 40 39 38 33 31 29 27 25 24 23 22 20 18 11 10 9 8 7 6 5 4 3 2 1 FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION SHCS, LOW HEAD, RoHS, M5 X 10 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SCR, BHSC, RoHS (M6 X 20) FEED FINGER ASSEMBLY,EF RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM, STEPPED, ASIAN STYLE, END FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM ASSY, LUBRICATOR, END FEED SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SHCS, LOW HEAD, RoHS, M4 X 20 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) PAWL, EF, AIR SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER, FRONT CASTING STUD, THREADED PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP PLATE, REAR SHEAR SPACER, SHEAR PLATE PLATE, RETAINING ANVIL, SPLICE TYPE BLADE, SHEAR CRIMPER, WIRE Ocean End Feed Applicator - DRAWING NO 2150122 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 251 40 6 62 FEED TYPE 38 39 D 7 7 MECHANICAL 145 153 2 246 139 140 166 D 2 2 A 59 239 58 8 63 1 PNEUMATIC 7 82 C C 238 1 1 249 2 70 41 250 A 54 137 163 55 10 172 20 2 A 57 64 164 51 33 23 SERVO LATCH PLATE 67 213 B 84 66 18 B 24 22 25 CAM POSITIONS 33 53 30mm STROKE 30mm STROKE 30mm STROKE 142 152 29 48 SERVO FEEDER NOT INCLUDED A 33 27 141 31 8 1 9 10 11 1 133 186 135 4 240 183 REF A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 PACIFIC VERSION 49 MECHANICAL PRE FEED 11 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 13MAY2014 CHK 13MAY2014 APVD 13MAY2014 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150122 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A1