8-2150462-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-2 ALL RIGHTS RESERVED. PART NUMBER REVISION DESCRIPTION APPLICATOR STYLE CONVERSION CHART FEED TYPE CONVERT TO - - - - - - 8- 2150462 -4 - - A FINE CRIMP HEIGHT ADJUST PNEUMATIC SERVO LATCH PLATE 2119951-1 1901697-1 8- 2150462 -5 2150462 -5 A FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE - - - - 2150462 -6 A NON-CRIMP HEIGHT ADJUST SERVO LATCH PLATE 11 2150462 -7 A FINE CRIMP HEIGHT ADJUST CRIMP TOOLING KIT 4 NONE - SMART APPLICATOR 4 2161326-1 - PNEUMATIC FEED 2119950-1 2031314-1 - - - - - - CRIMP WIRE INSUL SIZE - - - 2119641-1 - - - - - - - - - 2168400-7 - (QUANTITY 2) - - - 2063440-1 - - - - - - - - - - - - - - 6 TYPE F F 2.54 mm [.100] 4.19 mm [.165] APPL INSTRUCTIONS 408-10390 STOCKO TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION TERMINAL TERMINAL NAME: WIRE STRIP LENGTH n 5.10-6.10 mm [.201-.240 IN] C TERMINAL APPLICATION SPECIFICATION NONE - TERMINALS APPLIED TE TERMINAL 2113541-1 WIRE SIZE 2.50mm2 2.00mm2 1.50mm2 B 10 RSB 7961 F6.3 C1__DWG_PN_1_1 3.00-4.00 mm [.118-.157 IN] - - - 12 STOCKO TERMINAL C1__DWG_PN_1_0 INSULATION DIAMETER RANGE - C1__DWG_PN_2_0 TE TERMINAL W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 2.21+/-0.05 [.087+/-.002] 2.05+/-0.05 [.081+/-.002] 1.89+/-0.05 [.074+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY STOCKO TERMINAL 6 C1__DWG_PN_4_0 C1__DWG_PN_2_1 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 C1__DWG_PN_3_0 W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 9 4.3 W1__FA_SETTING_1 6.3 W1__FA_SETTING_2 7.9 W1__FA_SETTING_3 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 6 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 2150462 -4 2150462 -5 2150462 -6 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 A APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 37 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 180. 1 & 180. & 252. 1 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 10 TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 11 WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT 1 - 1 - 1 - 1 - 1 1 1 -77 -7 -6 -5 -2 2119957-2 8-21084-0 2119640-1 2079988-1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI PART NO DESCRIPTION 12 TERMINAL LUBRICANT IS RECOMMEDNED. 260 252 250 249 ITEM NO 1 1 Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 - - - - 1 - 1 - 1 1 - 1 - 1 1 - - 1 - - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - 2 2 - - - - 1 - - 1 1 - - 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - - - 2 - 1 1 1 1 - REF REF REF REF - - - - 1 - - - - 1 - - REF REF - - 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 - - 1 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 - 1 1 - 3 - 3 3 - 1 1 1 1 - 3 3 3 3 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - - - - 1 - - - - 1 - 1 1 1 1 - 1 - 1 1 - 1 1 1 1 - 1 - 1 1 - 1 - 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 1 - 7 7 7 7 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 4 4 4 4 - 1 1 1 1 - 1 1 1 1 - - - - - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - - - - - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 66 P LTR DESCRIPTION DATE DWN APVD 1 DEVELOPMENT 24JUL2014 YY UG A RELEASED 15SEP2014 YY UG PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 4 of 4) 2119641-1 2119798-1 1-22279-3 2119759-1 2119082-3 2079764-1 2119083-1 2168400-7 2063440-1 2119740-2 1803052-1 1-1752354-2 6-993111-6 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 3-23627-7 SEE NOTE 4 1633743-1 2119955-2 455888-5 2119956-2 2-18032-2 2119740-1 2168078-1 1901681-9 2168400-5 2119793-1 992763-5 2079383-4 2168400-4 1-2168083-0 5018030-2 5018030-1 986965-8 1-5018030-0 2031314-1 18023-9 2119655-5 2119369-1 2079383-7 2119645-1 2119957-1 2119644-2 2119085-1 2119092-1 1-18028-2 2168083-9 2168083-2 240639-1 1320906-1 1752371-5 240825-1 2-22281-3 1752373-4 1901259-6 1-2079383-1 1752360-1 240644-9 6-690482-6 5-1803001-4 2217206-1 6-240641-5 2-238009-5 5-2119582-0 455888-7 3-456407-5 -77 -7 -6 -5 -2 ATLANTIC VERSION AMP 4805 REV 31MAR2000 A REVISIONS DIST - 6 APPLICATOR DATA LOC 1 PART NUMBERS REQUIRED 2150462 -2 7- 2150462 -7 D 6 MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24JUL2014 CHK 24JUL2014 APVD 24JUL2014 Y.YIN G.BAILEY U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION PRODUCT SPEC - 248 247 246 245 244 243 242 240 238 213 183 180 177 176 175 174 172 166 164 163 137 135 133 84 82 71 70 67 66 65 64 63 62 60 57 56 55 54 53 52 51 49 46 44 41 40 39 38 37 35 33 31 29 27 25 24 23 22 20 18 17 13 11 10 9 8 7 6 5 4 3 2 1 FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, END FEED, NON-ADJUST CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 AIR FEED MODULE TAG,IDENTIFICATION FEED FINGER ASSEMBLY,EF STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM ASSY, LUBRICATOR, END FEED SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL SHCS, LOW HEAD, RoHS, M4 X 20 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 FEED FINGER SUBASSEMBLY SCR, SKT HD CAP M4 X 6.0 APPLICATOR BASIC ASSEMBLY, EF RAM,AMP STYLE, END FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 8.0 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SCR, BHSC, RoHS (M6 X 12) SPACER,HOLD-DOWN PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150462 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 1 REVISIONS DIST 66 P LTR - 6 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 37 40 44 245 REF 6 62 38 D D 39 17.27 [0.680] 247 260 7 7 2 246 252 2 245 35 2 44 180 REF 243 HOLDDOWN SET-UP 6 2 1 FEED TYPE 56 7 2 244 166 242 5 8 PNEUMATIC 177 63 250 82 1 238 1 2 249 137 A C C 163 2 3 2 1 2 4 41 2 176 172 70 175 54 174 52 51 55 64 65 6 23 10 180 2 A 164 20 67 213 66 57 SERVO LATCH PLATE 33 18 B B CAM POSITION 30mm STROKE 29 248 33 27 8 1 46 60 31 13 9 1 84 11 1 17 53 33 25 22 SERVO FEEDER NOT INCLUDED A 24 4 135 133 183 240 REF 49 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE AIR FEED AMP 4805 REV 31MAR2000 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24JUL2014 CHK 24JUL2014 APVD 24JUL2014 Y.YIN G.BAILEY U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150462 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER DESCRIPTION A WIRE SIZE 2.50mm2 2.00mm2 1.50mm2 8- 2150462 -5 - - SMART APPLICATOR 2161326-1 - 8- 2150462 -4 - - - - - - - - - - PNEUMATIC FEED 2119950-1 2031314-1 - 2119641-2 - 2063440-1 2168400-7 (QUANTITY 2) - - CRIMP TOOLING KIT - - - - - - - - 6 6 TYPE F F TE CRIMP SPECIFICATION n INSULATION DIAMETER RANGE 3.00-4.00 mm [.118-.157 IN] - - - - 10 12 RSB 7961 F6.3 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 STOCKO TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_2_1 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_3 1901697-1 - STOCKO TERMINAL W1__DWG_WGAUGE_2 2119951-1 - - W1__DWG_WGAUGE_1 SERVO LATCH PLATE - 4 2.21+/-0.05 [.087+/-.002] 2.05+/-0.05 [.081+/-.002] 1.89+/-0.05 [.074+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 4.3 6.3 7.9 6 9 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. B 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- 2150462 -4 2150462 -5 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. A 1 6 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 9 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 10 TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 11 THE RECOMMENDED SET-UP FOR END FEED APPLICATORS IS POST-FEED WITH ITEM 2119653-1. THE APPLICATOR CAN BE CONFIGURED FOR PRE-FEED WITH ITEM 2119652-1 BUT MAY ENCOUNTER PROBLEMS WITH SOME APPLICATIONS. FEED ISSUES OR TERMINAL JAMMING MAY OCCUR IN THE PRE-FEED CONFIGURATION. 12 TERMINAL LUBRICANT IS RECOMMEDNED. AMP 4805 REV 31MAR2000 & 180. 1 1 & 153. 8 66 P LTR DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - - - NONE C1__DWG_PN_1_1 - - 5.10-6.10 mm [.201-.240 IN] 2113541-1 - NONE TERMINAL C1__DWG_PN_1_0 - FINE CRIMP HEIGHT ADJUST WIRE STRIP LENGTH TE TERMINAL - A STOCKO TERMINAL TERMINALS APPLIED - 2- 2150462 -7 APPL INSTRUCTIONS 408-10390 C - SERVO LATCH PLATE 4.19 mm [.165] TERMINAL APPLICATION SPECIFICATION PNEUMATIC A REVISIONS DIST PART NUMBERS REQUIRED FINE CRIMP HEIGHT ADJUST 2.54 mm [.100] TERMINAL NAME: CONVERT TO LOC 1 - A SIZE 2 SET UP GAUGE 2119599-2 2- 2150462 -5 APPLICATOR DATA TERMINAL DATA: 3 APPLICATOR STYLE CONVERSION CHART FEED TYPE FINE CRIMP HEIGHT ADJUST 7- 2150462 -7 WIRE INSUL 4 20 REVISION 2- 2150462 -2 CRIMP 5 ALL RIGHTS RESERVED. PART NUMBER D 6 1 - 1 - 1 - 1 1 1 -77 -27 -25 -22 2119782-1 2119640-1 2079988-1 PART NO FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI DESCRIPTION 251 250 249 1 1 ITEM NO PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) 1-22279-3 2119082-3 2079764-1 2119083-1 2168400-7 2063440-1 2119740-2 2079383-9 1803052-1 1-1752354-2 6-993111-6 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2119653-2 2119655-6 2119651-1 2119092-2 3-23627-7 SEE NOTE 4 1633743-1 2119955-2 455888-5 2119956-2 2-18032-2 2119740-1 2168078-1 1901681-9 2168400-5 2119793-1 992763-5 2168400-4 1-2168083-0 5018030-2 5018030-1 986965-8 1-5018030-0 2031314-1 18023-9 2079383-7 2119645-1 2119957-1 2119644-2 1-18028-2 2168083-9 2168083-2 240639-1 1320906-1 1752371-5 240825-1 2-22281-3 1752373-4 1901259-6 1752360-1 240644-9 6-690482-6 5-1803001-4 2217206-1 6-240641-5 2-238009-5 5-2119582-0 455888-7 3-456407-5 -77 -27 -25 -22 PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - - 2 - - - 1 - - 1 - 4 4 4 - 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - - - 2 - 1 1 1 - REF REF REF - - - 1 - 1 1 1 - - - 1 - 1 1 1 - 1 1 1 - - - - 1 1 1 - 1 1 1 - 1 1 1 - - - 1 - - REF - - 1 - 1 1 1 - 1 1 1 - 1 1 1 - 2 2 2 - 1 - 1 - 2 2 2 - 1 1 1 - 2 2 2 - 1 1 1 - 3 3 3 - 3 3 3 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2 2 - 1 1 1 - - - 1 - - - 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 7 7 7 - 2 2 2 - 2 2 2 - 1 1 1 - 2 2 2 - 1 1 1 - 1 1 1 - 2 2 2 - 1 1 1 - 2 2 2 - 1 1 1 - 1 1 1 - - - - 1 1 1 1 1 1 1 - 1 1 1 - - - - 1 1 1 - 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24JUL2014 CHK 24JUL2014 APVD 24JUL2014 Y.YIN G.BAILEY U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION PRODUCT SPEC - 246 244 243 242 240 238 213 186 183 180 177 176 175 174 172 166 164 163 153 152 145 144 142 141 140 139 137 135 133 84 82 71 70 67 66 65 64 63 62 57 56 55 54 53 52 51 49 41 40 39 38 33 31 29 27 25 24 23 22 20 18 13 11 10 9 8 7 6 5 4 3 2 1 SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 AIR FEED MODULE TAG,IDENTIFICATION SCR, BHSC, RoHS (M6 X 20) FEED FINGER ASSEMBLY,EF STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM, ASIAN STYLE, END FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM ASSY, LUBRICATOR, END FEED SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 HOLDDOWN, TERMINAL SHCS, LOW HEAD, RoHS, M4 X 20 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) NUT, HEX, REG, RoHS, M3.5 FEED FINGER SUBASSEMBLY SCR, SKT HD CAP M4 X 6.0 SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 8.0 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SPACER,HOLD-DOWN PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150462 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - 251 40 62 6 141 38 REF 39 D 17.27 [0.680] 7 7 D 145 153 246 139 140 244 180 REF 243 6 HOLDDOWN SET-UP 2 166 242 8 FEED TYPE 2 2 1 56 7 2 PNEUMATIC 5 177 238 63 250 2 249 A 82 1 137 1 163 C C 172 2 3 4 2 1 2 41 2 51 176 175 64 54 174 55 23 52 65 6 70 67 10 A 180 20 2 213 164 66 SERVO LATCH PLATE 57 33 B 18 B CAM POSITION 30mm STROKE 29 152 SERVO FEEDER NOT INCLUDED A 33 27 8 1 141 144 31 13 9 1 84 11 1 186 53 33 25 22 24 4 133 135 240 183 REF 49 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24JUL2014 CHK 24JUL2014 APVD 24JUL2014 Y.YIN G.BAILEY U.GUO TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150462 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A