8-2151035-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION 2 FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151035-1 C MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151035-2 D 7- 2151035 -7 A FINE CRIMP HEIGHT ADJUST 1 REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER FEED TYPE C D 3 LOC 2151035 -1 2151035 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD B ECR-13-007941 14MAY2013 YY UG B1 ECR-15-014909 12OCT2015 KH CT C ECR-18-012858 13AUG2018 TB TE D ECR-19-009412 16JUN2019 TB TE PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 1.40 mm [.055] 3.18 mm [.125] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION SOCKET CONTACT 0.63X1.5mm SWS TERMINAL NAME: WIRE STRIP LENGTH - TERMINAL INSULATION DIAMETER RANGE 3.30-3.90 mm [.130-.154 IN] C - TERMINAL APPLICATION SPECIFICATION n 114-18286 - - 1.10-1.60 mm [.043-.063 IN] - - - - 3 - WIRE SIZE 0.50mm2 0.35mm2 TE TERMINAL C1__DWG_PN_1_0 C1__DWG_PN_2_0 C1__DWG_PN_1_1 TE SEAL 967067-1 C1__DWG_PN_3_0 C1__DWG_PN_3_1 967067-2 C1__DWG_PN_3_2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 - TERMINALS APPLIED TE TERMINAL 1241603-1 - 1.01+/-0.05 [.040+/-.002] 0.92+/-0.05 [.036+/-.002] TE SEAL 963142-1 CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 C1__DWG_PN_4_0 6.6 7.4 - 1.4-2.1 C1__DWG_PN_4_1 963142-2 - SEAL INSULATION DIAMETER RANGE - 0.9-1.4 C1__DWG_PN_4_2 - 4 - W1__FA_SETTING_1 - W1__FA_SETTING_2 5 - 1 2 3 B 4 5 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - 1 1 1 1 - 1 1 1 1 A - 1 - 1 1 1 1 1 1 1 1 1 - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 2 1 1 - 4 2 2 - 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 mm & 4 of 4) MATERIAL - PART NO 1 -77 -72 -71 -2 DIMENSIONS: -1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 2119641-1 2119082-9 2079764-1 2119083-1 18023-1 2119580-1 2844940-1 994970-2 1-18028-2 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338685-1 2168083-3 2168083-2 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1752356-3 2079383-5 2-2844962-8 2844992-1 455888-4 1320928-2 2168083-2 1-18028-2 2119533-1 879657-2 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 5-1333201-1 2-240641-4 2-2119781-4 238011-2 1633966-7 455888-6 456402-1 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 5.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED HOLD DOWN INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 20SEP2011 CHK 20SEP2011 APVD 20SEP2011 Y.YIN G.BAILEY S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119083 1 18023-1 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 1-18028-2 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 4 2168083-3 2 2168083-2 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1752356-3 2 2079383-5 2 2-2844962-8 1 2844992-1 1 455888-4 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 879657-2 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 5-1333201-1 1 2-240641-4 1 2-2119781-4 1 238011-2 1 1633966-7 1 455888-6 1 456402-1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764 248 244 243 242 241 239 238 164 119 99 98 82 71 67 66 60 59 57 56 54 52 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 18 13 12 11 10 9 8 7 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-9 DESCRIPTION PRODUCT SPEC - 1 2119641-1 Ocean Side Feed Applicator - DRAWING NO 2151035 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 REF 5 D 59 56 1.8 REF 44 PNEUMATIC 2 57 REF SHEAR DEPRESSOR DETAIL 244 243 A 52 238 242 18 3 2 7 8 59 C 82 1 REF 1.0 0.5 34 REF 1 C 2 SEE DETAIL A 3 1 56 4 TERMINAL SUPPORT LOCATION 28 5 41 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 44 44.61 66 DETAIL A 164 33 67 A 24 B 2 57 REF 0.05 5 RAM SET-UP 19 30 20 29 21 B 9 1 12 241 13 ITEM 30 LOCATED AT FRONT HOLES 1 CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 47 30 29 REF 46 98 99 34 54 8 1 60 54 10 1 119 11 248 48 REF FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 20SEP2011 CHK 20SEP2011 APVD 20SEP2011 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151035 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV D 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151035 -1 C FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151035 -7 A CRIMP TOOLING KIT - D 3 2 LOC PART NUMBER 2- 2151035 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 1.40 mm [.055] 3.18 mm [.125] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION SOCKET CONTACT 0.63X1.5mm SWS TERMINAL NAME: WIRE STRIP LENGTH TERMINAL INSULATION DIAMETER RANGE 3.30-3.90 mm [.130-.154 IN] C - TERMINAL APPLICATION SPECIFICATION n 114-18286 - - 1.10-1.60 mm [.043-.063 IN] - - - - TE TERMINAL 1241603-1 TE TERMINAL C1__DWG_PN_2_0 C1__DWG_PN_1_1 TE SEAL C1__DWG_PN_3_0 967067-1 967067-2 C1__DWG_PN_3_1 C1__DWG_PN_3_2 TE SEAL 963142-1 963142-2 1 - 0.50mm2 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 1.01+/-0.05 [.040+/-.002] 0.92+/-0.05 [.036+/-.002] CRIMP HEIGHT REFERENCE SETTING - W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 6.6 7.4 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - B 5 1 1 1 1 1 1 1 1 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 1 - 1 1 1 1 - A 1 1 - 1 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 1 1 1 - 1 2 - - 1 2 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 2 - 1 1 1 - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 - 2 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 2 - 4 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 1 - 3 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - 5 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - W1__FA_SETTING_2 4 - - W1__FA_SETTING_1 1 4 - 4 - 1 - WIRE SIZE - REF REF - 0.9-1.4 C1__DWG_PN_4_2 1 1 - 1.4-2.1 C1__DWG_PN_4_1 1 - - C1__DWG_PN_4_0 1 1 SEAL INSULATION DIAMETER RANGE 1 1 - 2119082-9 2079764-1 2119083-1 18023-1 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 5-18022-5 985575-3 1338685-1 2168083-2 18023-9 2119652-1 1803602-1 1752356-3 2079383-5 2-2844962-8 2844992-1 455888-4 1320928-2 2168083-2 1-18028-2 2119533-1 879657-2 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 5-1333201-1 2-240641-4 2-2119781-4 238011-2 1633966-7 455888-6 456402-1 1 1 - 3 TERMINALS APPLIED C1__DWG_PN_1_0 1 1 1 1 1 1 PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 5.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED HOLD DOWN INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 20SEP2011 CHK 20SEP2011 APVD 20SEP2011 Y.YIN G.BAILEY S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 18023-1 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338685-1 2 2168083-2 3 18023-9 1 2119652 1 1803602-1 1 1752356-3 2 2079383-5 2 2-2844962-8 1 2844992-1 1 455888-4 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 879657-2 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 5-1333201-1 1 2-240641-4 1 2-2119781-4 1 238011-2 1 1633966-7 1 455888-6 1 456402-1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119083 244 243 242 241 239 238 164 151 144 143 142 141 140 119 99 98 82 71 67 66 59 57 56 52 49 48 41 34 33 30 29 28 24 21 20 19 18 13 12 11 10 9 8 7 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079764 DESCRIPTION PRODUCT SPEC - 1 2119082-9 Ocean Side Feed Applicator - DRAWING NO 2151035 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL 140 A D 2 244 239 18 59 7 242 57 3 2 56 PNEUMATIC D 1.8 REF 243 52 REF 5 REF SHEAR DEPRESSOR DETAIL 82 A 1 1 238 2 3 REF 8 1 4 59 1.0 34 28 0.5 REF 5 41 TERMINAL SUPPORT LOCATION C C SEE DETAIL A 56 164 2 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 57 66 33 30 DETAIL A 5 35.58 0.05 67 A 24 140 REF 19 20 29 9 21 1 RAM SET-UP 12 241 13 1 B B ITEM 30 LOCATED AT FRONT HOLES CAM POSITIONS 30mm STROKE 141 99 34 143 8 1 144 143 10 1 119 11 30 REF REF 29 30mm STROKE 30mm STROKE 142 98 151 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 20SEP2011 CHK 20SEP2011 APVD 20SEP2011 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151035 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D