8-2151205-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION G FINE CRIMP HEIGHT ADJUST MECHANICAL 5-2151205-1 G SEAL STRIPPER CRIMPER TERMINATING UNIT MECHANICAL 5-2151205-2 H 7-2151205-1 G 7-2151205-2 H 7- 2151205 -7 A WIRE INSUL FINE CRIMP HEIGHT ADJUST - TYPE - F O 3 WIRE STRIP LENGTH 3.00-3.50 mm [.118-.138 IN] TERMINAL APPLICATION SPECIFICATION TE TERMINAL (A) 282110-1 n (A)114-20045 (B)114-20062 TERMINALS APPLIED TE CRIMP SPECIFICATION 1.50mm2 INSULATION DIAMETER RANGE 3 1.70-3.30 mm [.067-.130 IN] 16 AWG 1.00mm2 - - - - - C1__DWG_PN_2_0 TE SEAL TE SEAL C1__DWG_PN_3_0 0.75mm2 W1__DWG_WGAUGE_4 1.40+/-0.05 [.055+/-.002] 1.33+/-0.05 [.052+/-.002] 1.22+/-0.05 [.048+/-.002] 1.14+/-0.05 [.045+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 4.6 5.4 6.6 - SEAL INSULATION DIAMETER RANGE C1__DWG_PN_4_0 (A) 281934-2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_3 - - 6 C1__DWG_PN_4_1 (A) 281934-3 (B) 828904-1 W1__DWG_WGAUGE_2 - - C1__DWG_PN_1_1 W1__DWG_WGAUGE_1 - - C1__DWG_PN_4_2 - C1__DWG_PN_4_3 (B) 828905-1 WIRE SIZE - 6 TE TERMINAL C1__DWG_PN_1_0 - MINI MIC RECEPT CONTACT - C1__DWG_PN_4_4 - 4 - W1__FA_SETTING_1 5 W1__FA_SETTING_2 W1__FA_SETTING_3 7.7 - 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY 3 B 4 5 6 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - TERMINAL LUBRICANT IS RECOMMENDED. - 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT 101-35000. 1 - 1 - 1 1 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - A 1 1 1 1 - 1 1 1 1 1 1 - REF 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 1 - REF 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 - 1 1 - - 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 REF - REF DESCRIPTION DATE DWN APVD F ECR-18-003427 06MAR2018 MP JD G ECR-18-008658 07JUN2018 LG TE H ECR-19-006015 15APR2019 FJ CT H1 ECR-22-131140 02MAR2022 TB GB 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 2 1 1 1 1 1 1 1 1 1 1 4 1 4 2 4 2 1 2 1 1 1 2 - 1 1 - - 1 - - - - 1 - 1 1 1 1 1 1 2 1 2 2 2 2 1 2 1 1 1 1 1 1 1 - 1 - 1 1 1 - 2 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: -1 PART NO 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 RAM ASSEMBLY, SF ATLANTIC APPLICATOR BASIC ASSEMBLY, SF FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 15NOV2011 CHK 15NOV2011 APVD 15NOV2011 Y.YIN G.BAILEY S.XI WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119641-1 1 2119082-2 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 4-1722335-3 1 1-5018030-0 1 1-1752354-9 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 1 COUNTER_994970 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 4 2168083-3 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-8 1 2844992-1 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1333205-6 1 3-240641-4 .. 1 ITEM_6 1 2119781-1 1 2-238011-2 1 3-2119784-8 1 455888-9 1 4-456406-1 293 292 248 244 243 242 241 239 238 182 181 180 177 176 175 174 164 119 113 99 98 82 71 67 66 60 59 57 56 54 53 50 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - - 1 2-1803583-1 TE Connectivity APPLICATION SPEC - 1 1803515-3 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 1 1803515-3 2-1803583-1 2119641-1 2119082-2 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 4-1722335-3 1-5018030-0 1-1752354-9 993111-1 5-22280-0 1752353-3 1901680-2 994970-2 1-18028-2 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338685-1 2168083-3 2168083-3 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 2-1752356-0 2079383-5 2-2844962-8 2844992-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1333205-6 3-240641-4 2119781-1 2-238011-2 3-2119784-8 455888-9 4-456406-1 - REF REF -77 -72 -71 -52 -51 -2 AMP 4805 REV 31MAR2000 LTR D - TE TERMINAL P - - 3.68 mm [.145] 66 PNEUMATIC CRIMP TOOLING KIT 2.28 mm [.090] REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 MECHANICAL PNEUMATIC AND CRIMP TOOLING KIT SIZE TERMINAL NAME: 2 PNEUMATIC MECHANICAL AND CRIMP TOOLING KIT APPLICATOR DATA TERMINAL DATA: 3 PNEUMATIC SEAL STRIPPER CRIMPER TERMINATING UNIT APPLICATOR INSTRUCTIONS 408-35042 C FEED TYPE 2151205 -1 CRIMP 4 LOC DESCRIPTION H 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2151205 -2 D 6 Ocean Side Feed Applicator - DRAWING NO 2151205 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV H1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - FEED TYPE MECHANICAL A D 239 REF 5 D 59 56 1.1 REF 44 PNEUMATIC 293 57 2 REF 5 SHEAR DEPRESSOR DETAIL 244 243 A 53 238 50 242 1.4 # 0.5 7 8 59 C 3 2 82 1 1 34 REF 2 SEE DETAIL A 3 177 56 1 4 2 176 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 2 REF C TERMINAL SUPPORT LOCATION 28 5 41 174 44 293 REF 175 44.54 0.05 181 182 DETAIL A 3 66 180 2 19.3 67 57 164 33 A 24 B 0.5 5 180 REF 19 RAM & HOLD DOWN SET-UP 30 20 9 29 21 12 B 1 241 13 ITEM 30 LOCATED AT FRONT HOLES 1 CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 47 30 REF 29 REF 113 6 46 292 98 99 34 54 8 1 60 54 10 1 119 11 248 48 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 15NOV2011 CHK 15NOV2011 APVD 15NOV2011 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151205 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV H1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151205 -1 G FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151205 -7 A CRIMP TOOLING KIT - H 3 2 LOC PART NUMBER 2- 2151205 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D APPLICATOR DATA CRIMP SIZE WIRE INSUL TYPE F O 2.28 mm [.090] 3.68 mm [.145] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: MINI MIC RECEPT CONTACT TERMINAL NAME: WIRE STRIP LENGTH 3.00-3.50 mm [.118-.138 IN] C TERMINAL APPLICATION SPECIFICATION (A) 282110-1 n (A)114-20045 (B)114-20062 TERMINALS APPLIED TE TERMINAL TE CRIMP SPECIFICATION - - C1__DWG_PN_2_0 TE SEAL C1__DWG_PN_3_0 C1__DWG_PN_4_0 1.50mm2 16 AWG 1.00mm2 0.75mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 1.40+/-0.05 [.055+/-.002] 1.33+/-0.05 [.052+/-.002] 1.22+/-0.05 [.048+/-.002] 1.14+/-0.05 [.045+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 4.6 5.4 6.6 1 - SEAL INSULATION DIAMETER RANGE 1 - 4 - C1__DWG_PN_4_1 - - C1__DWG_PN_4_2 1 - C1__DWG_PN_4_3 1 - C1__DWG_PN_4_4 1 - 6 1 - 4 1 - 1 - 1 - W1__FA_SETTING_1 1 - W1__FA_SETTING_2 1 - W1__FA_SETTING_3 7.7 2 - 1 - 5 1 - 1 - B RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - 3 4 5 6 2 - 1 1 - 1 - - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - 1 1 2 - 2 - 1 1 - 1 - 1 - TERMINAL LUBRICANT IS RECOMMENDED. 1 - 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT 101-35000. 1 - 1 1 - 1 - 1 - 1 1 1 1 1 - 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. A 1 - 1 - - 1 1 1 1 1 1 1 - 1 1 PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 15NOV2011 CHK 15NOV2011 APVD 15NOV2011 Y.YIN G.BAILEY S.XI WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338685-1 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-8 1 2844992-1 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1333205-6 1 3-240641-4 .. 1 ITEM_6 1 2119781-1 1 2-238011-2 1 3-2119784-8 1 455888-9 1 4-456406-1 244 243 242 241 239 238 164 151 144 143 142 141 140 119 113 99 98 82 71 67 66 59 57 56 53 50 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - - 1 2079764_APP TE Connectivity APPLICATION SPEC - 1 2119082-2 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: 2119082-2 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 5-18022-5 985575-3 1338685-1 2168083-3 1803382-6 18023-9 2119652-1 1803602-1 2-1752356-0 2079383-5 2-2844962-8 2844992-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1333205-6 3-240641-4 2119781-1 2-238011-2 3-2119784-8 455888-9 4-456406-1 1 REF REF - TE SEAL CRIMP HEIGHT REFERENCE SETTING 1 - (B) 828905-1 CRIMP HEIGHT mm [INCH] - - (B) 828904-1 WIRE SIZE 1 - (A) 281934-2 (A) 281934-3 C1__DWG_PN_1_1 1 - 1.70-3.30 mm [.067-.130 IN] - 1 - 3 INSULATION DIAMETER RANGE - 1 - 6 TE TERMINAL C1__DWG_PN_1_0 - Ocean Side Feed Applicator - DRAWING NO 2151205 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV H1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D REF 5 239 140 59 5 243 242 A 1.1 REF 2 244 56 PNEUMATIC D REF SHEAR DEPRESSOR DETAIL 2 3 1.4 # 0.5 53 238 57 50 REF 8 7 59 34 82 C SEE DETAIL A REF TERMINAL SUPPORT LOCATION 1 C 1 56 2 3 1 4 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 28 5 41 35.58 140 0.05 REF 66 2 164 DETAIL A 67 33 57 A 24 B 5 RAM SET-UP 19 9 20 30 1 B 12 21 241 29 13 ITEM 30 LOCATED AT FRONT HOLES 1 CAM POSITIONS 30mm STROKE 30 29 REF 30mm STROKE 30mm STROKE 142 REF 151 113 48 6 141 98 99 34 143 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 15NOV2011 CHK 15NOV2011 APVD 15NOV2011 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151205 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV H1