8-2151247-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE F FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151247-1 F MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151247-2 F 7- 2151247 -7 A F 3 2 LOC 2151247 -1 2151247 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD C ECR-18-003257 02MAR2018 AW GB D ECR-18-007180 10MAY2018 FZ KZ E ECR-20-010619 27JUL2020 MEH RK F ECR-22-141869 09JUN2022 FJ JAH PNEUMATIC CRIMP TOOLING KIT - D D APPLICATOR DATA CRIMP SIZE WIRE INSUL TYPE F O 1.40 mm [.055] 1.40 mm [.055] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 3.00-3.50 mm [.118-.138 IN] TERMINAL APPLICATION SPECIFICATION n 114-5329 - TERMINALS APPLIED TE TERMINAL 1674311-1 - 0.64III SERIES RECEPTACLE CONTACT TERMINAL NAME: C TE CRIMP SPECIFICATION C1__DWG_PN_1_1 INSULATION DIAMETER RANGE - 3 1.06-1.70 mm [.042-.067 IN] - - - - - - - 7 TE TERMINAL 1674311-2 C1__DWG_PN_1_0 - C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 1674311-7 C1__DWG_PN_3_0 C1__DWG_PN_3_1 - TE TERMINAL 1674311-8 - 7 C1__DWG_PN_4_0 - C1__DWG_PN_4_1 - WIRE SIZE CRIMP HEIGHT mm [INCH] 5 0.50mm2 0.30 OR 0.35mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 0.86+/-0.05 [.034+/-.002] 0.76+/-0.05 [.030+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 8.6 9.9 - 4 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - 1 2 B 3 4 5 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - NOMINAL WIRE SIZES SHOWN. FOR SPECIFIC WIRE SIZES SEE APPLICATION SPECIFICATION. - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 7 - TERMINAL LUBRICANT IS RECOMMENDED. - 1 - 1 - 1 1 - 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - 1 1 1 1 A - 1 - 1 1 1 1 1 1 1 1 1 1 1 - 2 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 & 4 of 4) MATERIAL - 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH PART NO - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. mm -1 1 -77 -72 -71 -2 DIMENSIONS: 1 1 1 - 2 1 1 2 - - 1 1 2 - - 1 1 1 - - 1 1 1 - - 1 1 2 - 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 - 2 1 2 - 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - REF REF 1 1 1 1 REF 1 1 - - REF 1 1 1 1 1 1 1 - 1 1 1 2119641-1 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 1-18028-2 2119955-1 2844908-1 2844907-1 455888-3 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 1338685-1 2168083-3 1-2168083-0 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1752356-1 2079383-5 2-2844962-4 2844992-1 2119791-5 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-3 5-1333201-0 2119757-4 3-238011-8 1-1803019-4 3-1333281-2 - - FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 10 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE DEPRESSOR, WIRE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O CRIMPER, WIRE PREMIUM DWN 23NOV2011 CHK 23NOV2011 APVD 23NOV2011 K.HUANG S.XI I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-3 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 1338685-1 4 2168083-3 2 1-2168083-0 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1752356-1 2 2079383-5 2 2-2844962-4 1 2844992-1 1 2119791-5 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-3 1 5-1333201-0 .. 1 ITEM_7 .. 1 ITEM_6 1 2119757-4 1 3-238011-8 1 1-1803019-4 .. 1 ITEM_2 1 3-1333281-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764_APP 248 244 243 242 241 239 238 164 119 113 99 98 82 71 67 66 60 59 56 54 51 50 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-8 DESCRIPTION PRODUCT SPEC - 1 2119641-1 Ocean Side Feed Applicator - DRAWING NO 2151247 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV F C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 56 44 PNEUMATIC 2 244 243 A 242 238 3 2 51 8 50 59 82 1 C REF 1.3 1 0.5 34 REF C SEE DETAIL A 3 1 56 4 TERMINAL SUPPORT LOCATION 28 5 41 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 44.61 REF 66 DETAIL A 2 164 33 B 67 RAM SET-UP A 24 19 30 B 20 9 1 21 29 12 ITEM 30 LOCATED AT FRONT HOLES 241 13 CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 47 44 0.05 113 7 46 98 99 34 54 8 1 60 54 10 1 119 30 REF 29 REF 1 11 248 48 FEED TRACK POSITION GUIDE BY WIRE BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 23NOV2011 CHK 23NOV2011 APVD 23NOV2011 K.HUANG S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151247 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151247 -1 F FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151247 -7 A CRIMP TOOLING KIT - F 3 2 LOC PART NUMBER 2- 2151247 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D APPLICATOR DATA CRIMP SIZE WIRE INSUL TYPE F O 1.40 mm [.055] 1.40 mm [.055] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 3.00-3.50 mm [.118-.138 IN] TERMINAL APPLICATION SPECIFICATION 1674311-1 n 114-5329 - TERMINALS APPLIED TE TERMINAL - 0.64III SERIES RECEPTACLE CONTACT TERMINAL NAME: C TE CRIMP SPECIFICATION 1674311-2 C1__DWG_PN_1_1 1.06-1.70 mm [.042-.067 IN] - - - TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_3_0 - 1674311-7 C1__DWG_PN_3_1 1674311-8 1 - 5 0.50mm2 0.30 OR 0.35mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 0.86+/-0.05 [.034+/-.002] 0.76+/-0.05 [.030+/-.002] CRIMP HEIGHT REFERENCE SETTING - W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 8.6 9.9 4 - 7 1 1 1 1 1 1 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 - - - - - - 1 - 1 1 1 1 - A 1 1 - 1 1 1 - 1 1 1 - 1 2 1 - 1 2 2 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 2 - 1 1 1 - 1 1 1 - TERMINAL LUBRICANT IS RECOMMENDED. 2 - - 1 1 1 - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 2 1 - 1 1 2 - NOMINAL WIRE SIZES SHOWN. FOR SPECIFIC WIRE SIZES SEE APPLICATION SPECIFICATION. 1 1 - 5 2 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 2 - 4 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 1 - 3 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - B 1 1 - W1__FA_SETTING_2 1 1 - W1__FA_SETTING_1 4 - - 7 1 4 - CRIMP HEIGHT mm [INCH] - 1 - WIRE SIZE - REF REF - C1__DWG_PN_4_1 1 1 - TE TERMINAL 1 - - C1__DWG_PN_4_0 1 1 - C1__DWG_PN_2_0 1 1 - 2119082-8 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2119955-1 2844908-1 2844907-1 455888-3 1803607-3 2119740-1 2168078-1 5-18022-5 1338685-1 1-2168083-0 1803382-6 18023-9 2119652-1 1803602-1 1752356-1 2079383-5 2-2844962-4 2844992-1 2119791-5 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-3 5-1333201-0 2119757-4 3-238011-8 1-1803019-4 3-1333281-2 1 1 - 3 7 TE TERMINAL C1__DWG_PN_1_0 - INSULATION DIAMETER RANGE - 1 1 - - 1 1 PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 10 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE DEPRESSOR, WIRE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O CRIMPER, WIRE PREMIUM DWN 23NOV2011 CHK 23NOV2011 APVD 23NOV2011 K.HUANG S.XI I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-3 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 1338685-1 2 1-2168083-0 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 1752356-1 2 2079383-5 2 2-2844962-4 1 2844992-1 1 2119791-5 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-3 1 5-1333201-0 .. 1 ITEM_7 .. 1 ITEM_6 1 2119757-4 1 3-238011-8 1 1-1803019-4 .. 1 ITEM_2 1 3-1333281-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119083 244 243 242 241 239 238 164 151 144 143 142 141 140 119 113 99 98 82 71 67 66 59 56 51 50 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079764_APP DESCRIPTION PRODUCT SPEC - 1 2119082-8 Ocean Side Feed Applicator - DRAWING NO 2151247 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 243 242 A 2 244 56 PNEUMATIC D 2 3 1.3 238 50 59 34 82 1 1 C 56 3 1 4 28 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 5 140 41 35.58 164 2 0.05 67 33 RAM SET-UP A 24 B 19 20 30 B 9 21 29 1 12 ITEM 30 LOCATED AT FRONT HOLES 241 CAM POSITIONS 13 30 1 REF REF 29 30mm STROKE 30mm STROKE 142 REF 66 DETAIL A 30mm STROKE REF TERMINAL SUPPORT LOCATION C SEE DETAIL A REF 8 51 0.5 151 113 48 7 141 98 99 34 143 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY WIRE BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 23NOV2011 CHK 23NOV2011 APVD 23NOV2011 K.HUANG S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151247 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F