8-2151300-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION D FEED TYPE 2151300 -1 P FINE CRIMP HEIGHT ADJUST 3- 2151300 -2 P FINE CRIMP HEIGHT ADJUST 5-2151300-1 P SEAL STRIPPER CRIMPER TERMINATING UNIT 5-2151300-2 P 7-2151300-1 P 7-2151300-2 P 7- 2151300 -7 N 4 3 2 LOC DESCRIPTION P 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2151300 -2 6 MECHANICAL AND CRIMP TOOLING KIT 5 - 3 TYPE - F - SPECIAL 3 TE TERMINAL 1418760-1 5-1418760-2 WIRE SIZE 8 0.75mm2 2X 0.35mm2 0.5mm2 OR 20 AWG 114-18464 1418760-2 5-1418760-3 C1__DWG_PN_1_1 C1__DWG_PN_1_2 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 - - - - 2 3 4 - C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 1418760-3 C1__DWG_PN_3_0 C1__DWG_PN_3_1 TE TERMINAL - C1__DWG_PN_4_0 5-1418760-1 - C1__DWG_PN_4_1 - C1__DWG_PN_2_2 - 1.05+/-0.03 [.041+/-.001] 0.98+/-0.03 [.039+/-.001] 0.93+/-0.03 [.037+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 6.7 7.4 7.9 RECOMMENDED SPARE PARTS - 4 - W1__FA_SETTING_1 W1__FA_SETTING_2 5 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. A - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 - TERMINAL LUBRICANT IS RECOMMENDED. 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 8 - 5 THIS APPLICATOR IS EQUIPPED WITH THE DOUBLE ACTING FEED WITH SENSORS AND IS APPLICATION SPECIFIC AND DOES NOT REQUIRE ITEMS 49 & 248. 6 - 1.40-1.90 mm [.055-.075 IN] B 1 6 INSULATION DIAMETER RANGE CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 - 6 TE TERMINAL C1__DWG_PN_1_0 - TE CRIMP SPECIFICATION n - TERMINALS APPLIED - WIRE STRIP LENGTH TERMINAL APPLICATION SPECIFICATION - TAB CONTACT 1.2 MM 3.30-3.90 mm [.130-.154 IN] - APPLICATOR INSTRUCTIONS 408-35042 TERMINAL NAME: - TE TERMINAL 1 - 1 1 1 THIS CRIMP PARAMETER IS PROVIDED TO MEET A CUSTOM AND UNIQUE CUSTOMER REQUIREMENT. IT HAS BEEN EVALUATED AND IS CONDITIONALLY SPECIFIED BY TE CONNECTIVITY. THIS CUSTOMIZED CRIMP PARAMETER IS NOT LISTED AS AN APPROVED APPLICATION WITHIN A TE CONNECTIVITY APPLICATION SPECIFICATION; HOWEVER, IT HAS BEEN VALIDATED ACCORDING TO TE CONNECTIVITY SPECIFICATIONS 109-18079(TEST GROUP 1) AND 114-18022. TE CONNECTIVITY EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES THAT THE PRODUCT WILL PERFORM SIMILARLY TO VALIDATED AND APPROVED APPLICATIONS, AS STATED WITHIN TE CONNECTIVITY APPLICATION SPECIFICATIONS, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. AS SUCH, IT IS HIGHLY RECOMMENDED THAT THE CUSTOME PERFORM FURTHER DETAILED EVALUATION TO ASSESS PRODUCT PERFORMANCE IN THE SPECIFIC APPLICATION. - 1 1 1 1 2 1 1 1 1 1 1 1 - - REF 1 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 2 2 1 1 1 1 1 1 - - REF 1 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 REF 1 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 - ECR-20-015917 09NOV2020 JWC GB N1 ECR-21-000640 19JAN2021 FJ YY P ECR-21-006313 17JUN2021 FZ TE P1 ECR-21-006619 30JUN2021 JWC GB - - - 1 2 1 Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - -1 PART NO - - - REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 - 1 1 1 1 1 1 1 - 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 - 2 - - - 1 1 - 1 2 1 - 1 4 2 1 2 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: 1 - - - REF - - - 1 - - - 1 - - - 1 - - - 1 - - - 1 1 1 - 1 1 - - 1 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 2 1 - 1 - 2 1 - - - 2 1803515-3 2-1803583-1 2844950-1 2168083-1 1-1633782-1 2119641-1 2119082-5 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 4-1722335-3 1-5018030-0 1-1752354-8 993111-1 5-22280-0 1752353-3 1901680-2 994970-2 2119955-1 2844908-1 2844907-1 455888-5 5-547505-2 854769-5 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 21028-2 1338685-1 2168083-3 2-2168083-5 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 2-1752356-0 2079383-5 2-2844962-6 2844992-2 455888-3 1320928-6 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-4 1-1333231-3 5-240641-0 1-2119780-1 4-238011-2 1633989-1 3-1633730-2 - -77 -72 -71 -52 -51 -32 -2 ATLANTIC VERSION AMP 4805 REV 31MAR2000 N - - TERMINAL DATA: APVD D - C DWN PNEUMATIC CRIMP TOOLING KIT 1.83 mm [.072] DATE MECHANICAL PNEUMATIC AND CRIMP TOOLING KIT 1.40 mm [.055] DESCRIPTION PNEUMATIC - WIRE INSUL LTR MECHANICAL SEAL STRIPPER CRIMPER TERMINATING UNIT SIZE P PNEUMATIC DOUBLE ACTING PNEUMATIC WITH 5 SENSORS - CRIMP 66 MECHANICAL FINE CRIMP HEIGHT ADJUST APPLICATOR DATA REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - RAM ASSEMBLY, SF ATLANTIC APPLICATOR BASIC ASSEMBLY, SF AIR FEED MODULE SCR, SKT HD CAP, RoHS, M3 X 8.0 FENCE FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 14 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION, SPECIAL SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION, SPECIAL CRIMPER, WIRE DWN 24AUG2011 CHK 24AUG2011 APVD 24AUG2011 C. MOYER T. ELBIN T. ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 2 2168083-1 1 1-1633782-1 1 2119641-1 1 2119082-5 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 4-1722335-3 1 1-5018030-0 1 1-1752354-8 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 1 COUNTER_994970 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 SIMP_5-547505-2 1 854769-5 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 21028-2 1 1338685-1 4 2168083-3 2 2-2168083-5 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-6 1 2844992-2 1 455888-3 1 1320928-6 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-4 1 1-1333231-3 1 5-240641-0 1 1-2119780-1 1 4-238011-2 1 1633989-1 1 3-1633730-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2844950-1 293 292 290 269 267 248 244 243 242 241 239 238 182 181 180 177 176 175 174 164 113 99 98 82 77 74 71 67 66 60 59 58 56 54 53 50 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 5 4 3 1 TE Connectivity APPLICATION SPEC - 1 2-1803583-1 DESCRIPTION PRODUCT SPEC - 1 1803515-3 Ocean Side Feed Applicator - DRAWING NO 2151300 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV P1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 FEED TYPE 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - MECHANICAL A 239 59 D D 56 PNEUMATIC 44 A 238 2 244 243 59 53 50 242 2 3.1 3 7 8 177 SEE DETAIL A 82 1 56 C 293 0.5 REF 34 REF 1 C FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 3 2 176 2 2 1 4 174 TERMINAL SUPPORT LOCATION 28 5 41 175 181 DETAIL A 44 293 44.82 182 3 A B 2 15.8 66 67 290 33 A 24 21 9 1 ITEM 30 LOCATED AT REAR HOLES 12 56 241 CAM POSITIONS 47 RAM AND HOLD-DOWN SET-UP 20 269 13 30mm STROKE 30mm STROKE 113 6 46 292 98 99 34 54 8 1 60 54 10 1 20 30 REF 29 REF 1 11 12.0 248 48 REF B 29 30mm STROKE 0.5 74 19 267 SEE DETAIL A 180 77 58 30 59 0.05 180 164 DOUBLE ACTING PNEUMATIC WITH SENSORS REF 0.5 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24AUG2011 CHK 24AUG2011 APVD 24AUG2011 C. MOYER T. ELBIN T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151300 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV P1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2151300 -1 P FINE CRIMP HEIGHT ADJUST MECHANICAL 2- 2151300 -2 P FINE CRIMP HEIGHT ADJUST PNEUMATIC 4-2151300-2 P FINE CRIMP HEIGHT ADJUST 7- 2151300 -7 N CRIMP TOOLING KIT REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - DOUBLE ACTING PNEUMATIC WITH 5 SENSORS - D D CRIMP WIRE INSUL - APPLICATOR DATA SIZE - TYPE 1.83 mm [.072] - APPLICATOR INSTRUCTIONS 408-35042 3 C TE TERMINAL TERMINAL DATA: TAB CONTACT 1.2 MM TERMINAL NAME: WIRE STRIP LENGTH 3.30-3.90 mm [.130-.154 IN] TERMINAL APPLICATION SPECIFICATION 114-18464 - TERMINALS APPLIED TE TERMINAL 1418760-1 5-1418760-2 n C1__DWG_PN_1_1 5-1418760-3 C1__DWG_PN_1_2 5 - - - - C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 1418760-3 C1__DWG_PN_3_0 C1__DWG_PN_3_1 - WIRE SIZE 8 0.75mm2 2X 0.35mm2 0.5mm2 OR 20 AWG CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.05+/-0.03 [.041+/-.001] 0.98+/-0.03 [.039+/-.001] 0.93+/-0.03 [.037+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 6.7 7.9 B 1 2 3 4 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 5 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 5 THIS APPLICATOR IS EQUIPPED WITH THE DOUBLE ACTING FEED WITH SENSORS AND IS APPLICATION SPECIFIC AND DOES NOT REQUIRE ITEMS 49 & 151. 6 TERMINAL LUBRICANT IS RECOMMENDED. 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 8 A THIS CRIMP PARAMETER IS PROVIDED TO MEET A CUSTOM AND UNIQUE CUSTOMER REQUIREMENT. IT HAS BEEN EVALUATED AND IS CONDITIONALLY SPECIFIED BY TE CONNECTIVITY. THIS CUSTOMIZED CRIMP PARAMETER IS NOT LISTED AS AN APPROVED APPLICATION WITHIN A TE CONNECTIVITY APPLICATION SPECIFICATION; HOWEVER, IT HAS BEEN VALIDATED ACCORDING TO TE CONNECTIVITY SPECIFICATIONS 109-18079(TEST GROUP 1) AND 114-18022. TE CONNECTIVITY EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES THAT THE PRODUCT WILL PERFORM SIMILARLY TO VALIDATED AND APPROVED APPLICATIONS, AS STATED WITHIN TE CONNECTIVITY APPLICATION SPECIFICATIONS, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. AS SUCH, IT IS HIGHLY RECOMMENDED THAT THE CUSTOME PERFORM FURTHER DETAILED EVALUATION TO ASSESS PRODUCT PERFORMANCE IN THE SPECIFIC APPLICATION. ENTRY LEVEL APPLICATOR PART NUMBER 8-2151300-1 8-2151300-2 9-2151300-1 9-2151300-2 ITEM ITEM DESCRIPTION 2151300-1 1 WIRE CRIMPER 2151300-2 2-2151300-1 2-2151300-2 3 46 141 INSULATION CRIMPER BASIC SUB -ASSEMBLY BASIC SUB -ASSEMBLY LUBRICATOR SUBSTITUTE PART NUMBER 3-1803557-2 1 1 1803623-1 1 1803940-9 1 1-1803940-0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - AIR FEED MODULE SCR, SKT HD CAP, RoHS, M3 X 8.0 FENCE CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 14 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT SHEAR, FLOATING ANVIL, COMBINATION, SPECIAL SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION, SPECIAL CRIMPER, WIRE PART NO -77 -42 -22 -21 DELETE Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 - 2 1 1 - PACIFIC VERSION AMP 4805 REV 31MAR2000 - 1 ITEM SUBSTITUTION LIST SAME AS 1 1 2 1 - 1 1 2 - 1 1 1 - 1 1 1 - 2 1 1 - 2 2 1 - 1 2 2 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 1 2 - 1 1 1 - 2 - 1 - 1 1 - - 2 1 - - 1 2 1 - 1 1 2 - 1 1 1 - 2 1 1 - 1 2 1 - W1__FA_SETTING_2 1 1 2 - 7.4 1 1 1 - W1__FA_SETTING_1 1 1 1 - 1 1 1 - 4 1 1 1 - 1 1 1 - 1 1 1 - C1__DWG_PN_2_2 1 1 1 - C1__DWG_PN_4_1 1 1 1 - C1__DWG_PN_4_0 1 1 1 - 4 - 1 - 1 4 - - - 1 4 - TE TERMINAL 5-1418760-1 - 1 1 6 1 - - 1.40-1.90 mm [.055-.075 IN] 1 REF REF REF - INSULATION DIAMETER RANGE 6 TE TERMINAL 1418760-2 C1__DWG_PN_1_0 TE CRIMP SPECIFICATION 1 - - - 1 1 - - 1 1 1 - 1 1 1 - 1 1 1 - 2 1 1 2844950-1 2168083-1 1-1633782-1 2119082-5 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 2119955-1 2844908-1 2844907-1 455888-5 5-547505-2 854769-5 1803607-3 2119740-1 2168078-1 5-18022-5 21028-2 1338685-1 2-2168083-5 1803382-6 18023-9 2119652-1 1803602-1 2-1752356-0 2079383-5 2-2844962-6 2844992-2 455888-3 1320928-6 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1633861-4 1-1333231-3 5-240641-0 1-2119780-1 4-238011-2 1633989-1 3-1633730-2 - 2 1 - SPECIAL - 2 - F 1.40 mm [.055] 1 DWN 24AUG2011 CHK 24AUG2011 APVD 24AUG2011 C. MOYER T. ELBIN T. ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119082-5 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 SIMP_5-547505-2 1 854769-5 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 21028-2 1 1338685-1 2 2-2168083-5 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-6 1 2844992-2 1 455888-3 1 1320928-6 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1633861-4 1 1-1333231-3 1 5-240641-0 1 1-2119780-1 1 4-238011-2 1 1633989-1 1 3-1633730-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 1-1633782-1 290 269 267 244 243 242 241 239 238 164 151 144 143 142 141 140 113 99 98 82 77 74 71 67 66 59 58 56 53 50 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 5 4 3 1 TE Connectivity APPLICATION SPEC - 2 2168083-1 DESCRIPTION PRODUCT SPEC - 1 2844950-1 Ocean Side Feed Applicator - DRAWING NO 2151300 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV P1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. FEED TYPE 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - MECHANICAL 239 A 59 D D 56 PNEUMATIC 140 244 238 A 243 53 59 C 3.1 50 7 SEE DETAIL A 2 242 56 82 1 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) REF 8 2 34 3 0.5 REF TERMINAL SUPPORT LOCATION 1 C 3 1 4 28 5 41 DETAIL A 164 35.79 66 2 DOUBLE ACTING PNEUMATIC WITH SENSORS 33 A B 58 24 59 19 A 30 B 21 9 29 30mm STROKE 30 1 REF REF 29 11 30mm STROKE 30mm STROKE 142 ITEM 30 LOCATED AT REAR HOLES 241 13 CAM POSITIONS 1 12 269 56 RAM SET-UP 74 20 267 SEE DETAIL A 0.05 77 67 290 140 20 151 12.0 113 48 6 141 98 99 34 143 8 1 144 143 10 0.5 FEED TRACK POSITION GUIDE BY INSULATION BARREL 1 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24AUG2011 CHK 24AUG2011 APVD 24AUG2011 C. MOYER T. ELBIN T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151300 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV P1