8-2151349-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 DESCRIPTION FEED TYPE 2151349 -2 B FINE CRIMP HEIGHT ADJUST 7-2151349-2 B PNEUMATIC AND CRIMP TOOLING KIT 7- 2151349 -7 A CRIMP TOOLING KIT REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR PNEUMATIC DESCRIPTION DATE DWN APVD 1 DEVELOPMENT 19JUL2012 YY SX A RELEASED 21MAR2013 YY UG B ECR-22-132939 18MAR2022 JWC RK PNEUMATIC - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F OV 2.10 mm [.083] 2.50 mm [.098] APPLICATOR INSTRUCTIONS 408-35042 - 1 - 1 - FCI TERMINAL TERMINAL DATA: TERMINAL, 2.8mm SICMA-2 TERMINAL NAME: WIRE STRIP LENGTH 4.08-4.09 mm [.160-.161 IN] C FCI CRIMP SPECIFICATION TERMINAL APPLICATION SPECIFICATION 1.30-2.10 mm [.051-.083 IN] FCI SPEC - - - - - - - TE TERMINAL 1572406-1 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 1752406-2 C1__DWG_PN_3_0 C1__DWG_PN_3_1 1 0.75mm2 0.35+0.35 0.60mm2 0.50mm2 0.35mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 1.22+/-0.04 [.048+/-.002] 1.21+/-0.04 [.048+/-.002] 1.19+/-0.04 [.047+/-.002] 1.18+/-0.04 [.046+/-.002] 1.15+/-0.04 [.045+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 W1__DWG_CRIMP_HT_5 4.7 4.8 5.1 5.2 B 3 4 1 1 1 1 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 2 - 1 - - - - - - 1 - 1 1 1 2 - A 1 1 - 1 1 1 - 1 2 1 - 1 2 2 - 1 1 2 - WIRE SIZE. TO 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE THE CRIMP TOOLING. R EFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 4 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 4 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - RECOMMENDED SPARE PARTS 2 1 1 1 2 - 5.7 1 1 - W1__FA_SETTING_4 1 1 - W1__FA_SETTING_3 1 1 - W1__FA_SETTING_2 1 1 W1__FA_SETTING_1 1 1 - 4 1 1 - CRIMP HEIGHT REFERENCE SETTING 1 1 - CRIMP HEIGHT mm [INCH] 1 REF REF - WIRE SIZE 1 1 - C1__DWG_PN_4_1 1 1 - C1__DWG_PN_4_0 1 1 - FCI TERMINAL 211CC3S1220 1 1 FCI TERMINAL 211CC3S1120 C1__DWG_PN_1_0 1 1 - TERMINALS APPLIED 1 1 - - 1 1 - 3 1 1 - INSULATION DIAMETER RANGE 1 1 - 3 2119641-1 2119082-8 2079764-1 2119083-1 7-18023-7 2844940-1 2-1752354-3 993111-1 8-22280-7 1752353-2 1901680-2 994970-2 2844908-1 2844907-1 318563-1 455888-5 22278-8 854769-4 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 21028-2 1338685-1 2168083-3 1-5018030-0 1901681-1 18023-9 1803583-9 1803515-3 1803602-1 1-1752356-3 2079383-5 2-2844962-6 2844992-1 455888-3 1320928-4 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 3-1633138-8 2119780-7 3-238011-3 1633964-5 455888-3 8-1633305-5 1 1 1 1 2 1 -77 -72 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 AIR FEED MODULE STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC SCREW, LOCKING POST, LOCKING GUARD, FRONT CHIP SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION OVERLAP PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO DWN 19JUL2012 CHK 19JUL2012 APVD 19JUL2012 Y.YIN G.BAILEY S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119083 1 7-18023-7 1 2844940-1 1 2-1752354-3 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 1 COUNTER_994970 1 2844908 1 2844907 1 318563-1 1 455888-5 1 SIMP_22278-8 1 854769-4 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 21028-2 1 1338685-1 4 2168083-3 1 1-5018030-0 1 1901681-1 1 18023-9 1 1803583-9 1 1803515-3 1 1803602-1 1 1-1752356-3 2 2079383-5 2 2-2844962-6 1 2844992-1 1 455888-3 1 1320928-4 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 3-1633138-8 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-7 1 3-238011-3 1 1633964-5 1 455888-3 1 8-1633305-5 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764_APP 248 244 243 242 241 238 180 177 176 175 174 164 99 98 89 82 77 74 71 67 66 60 59 58 56 54 52 51 49 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-8 DESCRIPTION PRODUCT SPEC - 1 2119641-1 Ocean Side Feed Applicator - DRAWING NO 2151349 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV B C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE PNEUMATIC D D 44 A 2 238 244 59 243 242 177 2 1.0 3 SEE DETAIL A 8 56 82 1 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) C 1 C 3 TERMINAL SUPPORT LOCATION 1 4 28 2 176 DETAIL A 41 174 44 44.62 175 51 3 180 REF 0.05 66 15.1 0.5 67 2 164 77 33 A 24 180 REF 58 74 19 B 9 20 30 RAM AND HOLDDOWN SET-UP 1 B 12 21 241 29 13 1 ITEM 30 LOCATED AT REAR HOLES 30 REF 29 REF CAM POSITION 30mm STROKE 5 52 2 REF 34 REF 2 2 0.5 11 98 99 46 34 54 8 1 60 54 10 1 89 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE AIR FEED AMP 4805 REV 31MAR2000 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 19JUL2012 CHK 19JUL2012 APVD 19JUL2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151349 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 3 2 LOC PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2151349 -2 B FINE CRIMP HEIGHT ADJUST PNEUMATIC CRIMP TOOLING KIT - 7- 2151349 -7 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F OV 2.10 mm [.083] 2.50 mm [.098] APPLICATOR INSTRUCTIONS 408-35042 - FCI TERMINAL TERMINAL DATA: TERMINAL, 2.8mm SICMA-2 TERMINAL NAME: WIRE STRIP LENGTH 4.08-4.09 mm [.160-.161 IN] C FCI CRIMP SPECIFICATION TERMINAL APPLICATION SPECIFICATION - - - - - TE TERMINAL 1572406-1 1 1 - 1 - 1 - 1 - REF - FCI TERMINAL 211CC3S1120 C1__DWG_PN_1_1 1 - TERMINALS APPLIED C1__DWG_PN_1_0 1 - 3 1.30-2.10 mm [.051-.083 IN] - 1 - INSULATION DIAMETER RANGE FCI SPEC 1 - 3 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 1752406-2 C1__DWG_PN_3_0 C1__DWG_PN_3_1 FCI TERMINAL 211CC3S1220 1 - C1__DWG_PN_4_0 1 - C1__DWG_PN_4_1 4 - 1 - 1 - WIRE SIZE 0.75mm2 0.35+0.35 0.60mm2 0.50mm2 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 1.22+/-0.04 [.048+/-.002] 1.21+/-0.04 [.048+/-.002] 1.19+/-0.04 [.047+/-.002] 1.18+/-0.04 [.046+/-.002] 1.15+/-0.04 [.045+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 W1__DWG_CRIMP_HT_5 4.7 4.8 5.1 5.2 1 - 4 1 - 1 - 1 - W1__FA_SETTING_1 1 - W1__FA_SETTING_2 1 - W1__FA_SETTING_3 W1__FA_SETTING_4 1 - 5.7 1 - 2 - 1 - 1 - 1 - 1 - 1 B 1 2 3 4 1 - RECOMMENDED SPARE PARTS 1 - 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 2 - 2 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. 1 - 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 - 1 - 1 - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 - 1 - 1 - 1 1 1 1 WIRE SIZE. TO 1 - 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE THE CRIMP TOOLING. R EFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 - 1 1 - - - - - 1 - 1 1 1 1 - 1 1 1 A 2119082-8 2079764-1 2119083-1 7-18023-7 2844940-1 2-1752354-3 993111-1 8-22280-7 1752353-2 1901680-2 994970-2 2119641-2 2168083-8 2168083-9 1-1803583-0 1803516-1 2844908-1 2844907-1 318563-1 455888-5 22278-8 854769-4 1803607-3 2119740-1 2168078-1 5-18022-5 21028-2 1338685-1 1-5018030-0 1901681-1 18023-9 1803602-1 1-1752356-3 2079383-5 2-2844962-6 2844992-1 455888-3 1320928-4 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 3-1633138-8 2119780-7 3-238011-3 1633964-5 455888-3 8-1633305-5 1 1 PART NO -77 -22 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 AIR FEED MODULE STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC SCREW, LOCKING POST, LOCKING GUARD, FRONT CHIP SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION OVERLAP PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 19JUL2012 CHK 19JUL2012 APVD 19JUL2012 Y.YIN G.BAILEY S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 7-18023-7 1 2844940-1 1 2-1752354-3 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 1-1803583-0 1 1803516-1 1 2844908 1 2844907 1 318563-1 1 455888-5 1 SIMP_22278-8 1 854769-4 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 21028-2 1 1338685-1 1 1-5018030-0 1 1901681-1 1 18023-9 1 1803602-1 1 1-1752356-3 2 2079383-5 2 2-2844962-6 1 2844992-1 1 455888-3 1 1320928-4 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 3-1633138-8 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-7 1 3-238011-3 1 1633964-5 1 455888-3 1 8-1633305-5 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119083 244 243 242 241 238 180 177 176 175 174 164 151 144 143 141 140 99 98 89 82 77 74 71 67 66 59 58 56 52 51 49 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079764_APP DESCRIPTION PRODUCT SPEC - 1 2119082-8 Ocean Side Feed Applicator - DRAWING NO 2151349 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE PNEUMATIC D D 140 244 A 1.0 238 243 242 8 REF 34 3 59 0.5 REF TERMINAL SUPPORT LOCATION 177 SEE DETAIL A 56 82 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) C 2 2 DETAIL A 1 C 1 176 2 174 3 1 4 28 5 52 2 140 41 35.59 175 0.05 51 15.1 66 3 180 2 164 67 24 180 58 74 20 30 REF RAM AND HOLDDOWN SET-UP 19 B 0.5 77 33 A REF 9 21 B 1 12 29 ITEM 30 LOCATED AT REAR HOLES 241 13 CAM POSITION 30 1 REF REF 29 30mm STROKE 151 98 141 99 34 143 8 1 144 143 10 1 89 FEED TRACK POSITION GUIDE BY INSULATION BARREL 11 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 AIR FEED PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 19JUL2012 CHK 19JUL2012 APVD 19JUL2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151349 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B