8-2151392-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION FINE CRIMP HEIGHT ADJUST MECHANICAL 5-2151392-1 H SEAL STRIPPER CRIMPER TERMINATING UNIT MECHANICAL 5-2151392-2 H 7-2151392-1 H 7-2151392-2 H 7- 2151392 -7 A FINE CRIMP HEIGHT ADJUST - TYPE - F O 3 TE TERMINAL n 1 928 F00 025-EN - 1572253-1 1572253-2 1572253-3 WIRE SIZE 1.00mm2 0.75mm² or 18AWG 0.50mm2 1928498056 1928498058 C1__DWG_PN_1_2 C1__DWG_PN_1_3 1.20-2.10 mm [.047-.083 IN] - C1__DWG_PN_2_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 C1__DWG_PN_2_3 C1__DWG_PN_3_0 1572254-1 C1__DWG_PN_3_1 828904-1 828904-2 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 - - 1.36+/-0.05 [.053+/-.002] 1.27+/-0.05 [.050+/-.002] 1.18+/-0.05 [.046+/-.002] BOSCH SEAL C1__DWG_PN_4_0 1928300599 C1__DWG_PN_4_1 - SEAL INSULATION DIAMETER RANGE 7 - - C1__DWG_PN_3_4 CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 - C1__DWG_PN_3_3 W1__DWG_CRIMP_HT_1 - C1__DWG_PN_3_2 828904-3 - - TE SEAL - - CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 3 7 1928498054 C1__DWG_PN_1_1 - INSULATION DIAMETER RANGE - BOSCH TERMINAL C1__DWG_PN_1_0 - BOSCH CRIMP SPECIFICATION 3.70-4.50 mm [.146-.177 IN] TERMINALS APPLIED - WIRE STRIP LENGTH TERMINAL APPLICATION SPECIFICATION - TERMINAL 4.6 5.3 6.8 - 4 - W1__FA_SETTING_1 5 W1__FA_SETTING_2 W1__FA_SETTING_3 - 1 2 B 3 4 5 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 7 TERMINAL LUBRICANT IS RECOMMENDED. - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 1 1 1 - A 1 1 1 1 - 1 1 1 1 1 1 - REF 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 1 - REF 1 1 1 1 1 1 1 2 1 1 1 1 4 2 1 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 - LTR DESCRIPTION DATE DWN APVD E ECR-19-007637 14MAY2019 FJ TE F ECR-21-001914 15FEB2021 TB RK G ECR-21-006398 21JUN2021 MEH TE H ECR-22-132838 17MAR2022 FJ TE 1 1 - - 1 1 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - PART NO - - - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 - 1 1 1 - - 1 1 - - 1 1 1 - 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 - 1 1 - - - 2 - 1 - 1 1 1 - 2 1 2 - 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: -1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1803515-3 2-1803583-1 2119641-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 4-1722335-3 1-5018030-0 1-1752354-9 993111-1 5-22280-0 1752353-3 1901680-2 994970-2 1-18028-2 2119955-1 2844908-1 2844907-1 455888-8 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338685-1 2168083-3 2168083-3 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1-1752356-7 2079383-5 2-2844962-3 2844992-2 455888-4 1320928-1 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 2-1333204-6 3-240641-3 2119781-1 3-238011-3 3-2119784-1 455888-7 1-456405-6 - -77 -72 -71 -52 -51 -2 AMP 4805 REV 31MAR2000 P D - BOSCH TERMINAL 66 - - 4.06 mm [.160] TERMINAL NAME: A PNEUMATIC CRIMP TOOLING KIT 2.03 mm [.080] REVISIONS DIST MECHANICAL PNEUMATIC AND CRIMP TOOLING KIT SIZE 1 PNEUMATIC MECHANICAL AND CRIMP TOOLING KIT APPLICATOR DATA TERMINAL DATA: 2 PNEUMATIC SEAL STRIPPER CRIMPER TERMINATING UNIT APPLICATOR INSTRUCTIONS 408-35042 C FEED TYPE H WIRE INSUL 3 ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 2151392 -1 CRIMP 4 LOC DESCRIPTION H 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2151392 -2 D 6 TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 02DEC2011 CHK 02DEC2011 APVD 02DEC2011 Y.YIN G.BAILEY S.XI - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119641-1 1 2119082-9 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 4-1722335-3 1 1-5018030-0 1 1-1752354-9 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 1 COUNTER_994970 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-8 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 4 2168083-3 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1-1752356-7 2 2079383-5 2 2-2844962-3 1 2844992-2 1 455888-4 1 1320928-1 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 2-1333204-6 1 3-240641-3 .. 1 ITEM_6 1 2119781-1 1 3-238011-3 1 3-2119784-1 1 455888-7 1 1-456405-6 293 292 248 244 243 242 241 239 238 182 181 180 177 176 175 174 164 119 113 99 98 82 71 67 66 60 59 57 56 54 53 50 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2-1803583-1 TE Connectivity APPLICATION SPEC - 1 1803515-3 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH RAM ASSEMBLY, SF ATLANTIC APPLICATOR BASIC ASSEMBLY, SF FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean Side Feed Applicator - DRAWING NO 2151392 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV H C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 REF 5 D 59 56 1.8 REF 44 PNEUMATIC 293 2 57 REF SHEAR DEPRESSOR DETAIL 244 243 A 53 238 242 50 2 3 7 8 59 C 82 1 C 2 3 1 177 4 2 176 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 TERMINAL SUPPORT LOCATION 28 5 41 44 293 REF 174 181 2 44.61 175 182 DETAIL A 164 33 0.05 66 2 180 67 A 24 B 3 57 5 19.0 19 RAM SET-UP 9 21 1 12 241 13 ITEM 30 LOCATED AT FRONT HOLES 1 30 REF 29 REF CAM POSITIONS 30mm STROKE 30mm STROKE 113 7 292 46 98 99 34 54 8 1 60 54 10 1 119 11 248 48 B 20 29 47 0.5 180 REF 30 30mm STROKE 0.5 34 REF 1 SEE DETAIL A 56 1.0 REF FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 02DEC2011 CHK 02DEC2011 APVD 02DEC2011 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151392 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV H 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151392 -1 H FINE CRIMP HEIGHT ADJUST MECHANICAL CRIMP TOOLING KIT - H 7- 2151392 -7 3 2 LOC PART NUMBER 2- 2151392 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 2.03 mm [.080] 4.06 mm [.160] APPLICATOR INSTRUCTIONS 408-35042 BOSCH TERMINAL TERMINAL DATA: BOSCH CRIMP SPECIFICATION TERMINAL TERMINAL NAME: WIRE STRIP LENGTH n 3.70-4.50 mm [.146-.177 IN] TERMINAL APPLICATION SPECIFICATION C 1 928 F00 025-EN - TERMINALS APPLIED TE TERMINAL 1572253-1 1572253-2 1572253-3 WIRE SIZE 1.00mm2 0.75mm² or 18AWG 0.50mm2 C1__DWG_PN_1_2 1928498058 C1__DWG_PN_1_3 C1__DWG_PN_2_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 C1__DWG_PN_2_3 TE SEAL C1__DWG_PN_3_0 1572254-1 828904-1 C1__DWG_PN_3_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.36+/-0.05 [.053+/-.002] 1.27+/-0.05 [.050+/-.002] 1.18+/-0.05 [.046+/-.002] C1__DWG_PN_4_0 1928300599 C1__DWG_PN_4_1 828904-2 828904-3 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 4.6 5.3 6.8 - 2 RECOMMENDED SPARE PARTS 3 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 5 1 2 2 2 - 2 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 - - - 1 - 1 1 1 1 1 - 1 1 1 A 1 1 - 1 1 1 - 1 2 - - 1 1 1 - 1 2 1 - 7 TERMINAL LUBRICANT IS RECOMMENDED. 1 2 - 1 1 1 - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 - 1 2 1 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 2 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 1 1 1 - B 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 5 1 1 - W1__FA_SETTING_3 1 1 - W1__FA_SETTING_2 1 1 - W1__FA_SETTING_1 1 1 - 7 1 1 4 4 - - CRIMP HEIGHT REFERENCE SETTING 1 4 - C1__DWG_PN_3_4 - 1 - C1__DWG_PN_3_3 W1__DWG_CRIMP_HT_1 1 - - - REF REF - C1__DWG_PN_3_2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 BOSCH SEAL 1 1 SEAL INSULATION DIAMETER RANGE 1 - - - 1 1 - 7 1928498054 1928498056 C1__DWG_PN_1_1 - 1 1 - 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2119955-1 2844908-1 2844907-1 455888-8 1803607-3 2119740-1 2168078-1 5-18022-5 985575-3 1338685-1 2168083-3 1803382-6 18023-9 2119652-1 1803602-1 1-1752356-7 2079383-5 2-2844962-3 2844992-2 455888-4 1320928-1 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 2-1333204-6 3-240641-3 2119781-1 3-238011-3 3-2119784-1 455888-7 1-456405-6 1 1 - 3 1.20-2.10 mm [.047-.083 IN] - 1 - INSULATION DIAMETER RANGE - BOSCH TERMINAL C1__DWG_PN_1_0 - 1 1 1 PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 02DEC2011 CHK 02DEC2011 APVD 02DEC2011 Y.YIN G.BAILEY S.XI - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-8 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338685-1 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 1-1752356-7 2 2079383-5 2 2-2844962-3 1 2844992-2 1 455888-4 1 1320928-1 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 2-1333204-6 1 3-240641-3 .. 1 ITEM_6 1 2119781-1 1 3-238011-3 1 3-2119784-1 1 455888-7 1 1-456405-6 244 243 242 241 239 238 164 151 144 143 142 141 140 119 113 99 98 82 71 67 66 59 57 56 53 50 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2079764_APP TE Connectivity APPLICATION SPEC - 1 2119082-9 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean Side Feed Applicator - DRAWING NO 2151392 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV H C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D REF 5 239 140 59 1.8 REF 2 244 56 PNEUMATIC D 57 243 242 SHEAR DEPRESSOR DETAIL 2 3 53 A 238 1.0 # 0.5 50 REF 8 7 34 59 82 1 C SEE DETAIL A REF REF TERMINAL SUPPORT LOCATION 1 C 2 56 3 1 4 28 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 5 41 140 35.58 REF 0.05 164 66 DETAIL A 2 67 57 5 33 RAM SET-UP A 24 B 19 30 20 9 21 12 29 B 1 241 13 ITEM 30 LOCATED AT FRONT HOLES 1 CAM POSITIONS 30mm STROKE 30 REF 29 30mm STROKE 30mm STROKE 142 REF 151 113 48 7 141 98 99 34 143 8 1 144 143 10 1 119 FEED TRACK POSITION GUIDE BY INSULATION BARREL 11 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 02DEC2011 CHK 02DEC2011 APVD 02DEC2011 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151392 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV H