8-2151478-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION G FINE CRIMP HEIGHT ADJUST MECHANICAL 3- 2151478 -2 G FINE CRIMP HEIGHT ADJUST DOUBLE ACTING PNEUMATIC WITH SENSORS 7 7-2151478-1 G MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151478-2 G 7- 2151478 -7 G CRIMP WIRE INSUL FINE CRIMP HEIGHT ADJUST 1.83 mm [.072] 7 3 3.30-3.90 mm [.130-.154 IN] TERMINAL APPLICATION SPECIFICATION TE TERMINAL 1563888-1 WIRE SIZE 0.50mm2 114-18464 n 5 6 INSULATION DIAMETER RANGE - - 1.40-1.60 mm [.055-.063 IN] - - - - - - - C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_1_1 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 - - 6 TE TERMINAL C1__DWG_PN_1_0 - - TE CRIMP SPECIFICATION - TERMINALS APPLIED - - WIRE STRIP LENGTH 0.86+/-0.03 [.034+/-.001] - 4 CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 7.8 - W1__FA_SETTING_1 7 1 2 B 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 6 7 - MAXIMUM INSULATION CRIMP WIDTH 2.05mm & MAXIMUM INSULATION CRIMP HEIGHT 2.05mm. SEE APPLICATION SPECIFICATION TO CLARIFY. TERMINAL LUBRICANT IS RECOMMENDED. THIS APPLICATOR IS EQUIPPED WITH THE DOUBLE ACTING FEED WITH SENSORS AND IS APPLICATION SPECIFIC. IT DOES NOT REQUIRE ITEMS 49 & 248. 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - RECOMMENDED SPARE PARTS 3 5 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 - 1 1 1 1 - 1 1 1 1 A - 1 1 1 1 1 1 REF 1 1 1 1 1 1 1 2 1 1 1 4 2 1 1 1 1 1 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 2 - 1 - - P LTR DESCRIPTION DATE DWN APVD E ECR-18-008490 04JUN2018 MZ KZ F ECR-19-010974 15JUL2019 FJ TE F1 ECR-21-005485 17MAY2021 AJ YY G ECR-22-133686 24MAR2022 FZ GB - 1 1 1 1 1 1 1 1 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - - 1 PART NO - 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH -1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: 1 1 1 - 2 1 1 1 - - 1 1 2 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - - 1 1 1 - 1 1 1 - 1 1 1 1 2 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - REF REF 1 1 1 1 REF 1 1 - - REF 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 2844950-1 2119641-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119791-5 2119740-1 2168078-1 2168083-2 5-18022-5 1338685-1 2168083-3 2168083-8 5018030-1 811242-5 690753-2 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 7-1752356-7 2079383-5 2-2844962-6 2844992-2 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-3 1333231-9 240641-4 2119757-8 238011-9 1-1633989-5 3-456402-3 - -77 -72 -71 -32 -2 AMP 4805 REV 31MAR2000 66 D TYPE MCON-1.2 LL TERMINAL NAME: REVISIONS - - TE TERMINAL TERMINAL DATA: 1 DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER F SP 1.40 mm [.055] 2 PNEUMATIC CRIMP TOOLING KIT SIZE 3 PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT APPLICATOR INSTRUCTIONS 408-35042 C FEED TYPE 2151478 -1 APPLICATOR DATA 4 LOC DESCRIPTION G 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2151478 -2 D 6 - AIR FEED MODULE FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 16 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION, SPECIAL SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION, SPECIAL CRIMPER, WIRE PREMIUM DWN 27AUG2012 CHK 27AUG2012 APVD 27AUG2012 K.HUANG S.XI S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119791-5 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 1338685-1 4 2168083-3 2 2168083-8 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 7-1752356-7 2 2079383-5 2 2-2844962-6 1 2844992-2 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-3 1 1333231-9 1 240641-4 .. 1 ITEM_6 1 2119757-8 1 238011-9 1 1-1633989-5 .. 1 ITEM_2 1 3-456402-3 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119082-9 290 248 244 243 242 241 239 238 164 113 99 98 82 71 70 67 66 60 59 56 54 53 52 51 50 49 48 47 46 44 41 34 33 30 29 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119641-1 DESCRIPTION PRODUCT SPEC - 1 2844950-1 Ocean Side Feed Applicator - DRAWING NO 2151478 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV G C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. FEED TYPE 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - MECHANICAL A 239 59 D D 56 PNEUMATIC 44 238 A 2 244 53 243 59 242 7 82 SEE DETAIL A 1 56 0.5 52 C 1 TERMINAL SUPPORT LOCATION 4 70 5 51 41 44.61 44 REF 0.05 66 DOUBLE ACTING PNEUMATIC WITH SENSORS 2 164 A 33 290 B 67 A 24 59 RAM SET-UP 19 30 B 20 21 29 SEE DETAIL A 9 56 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 13 CAM POSITIONS 30 REF 29 REF 1 11 30mm STROKE 30mm STROKE 47 4.0 34 REF DETAIL A 30mm STROKE REF 1 3 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 3 8 50 C 2 20 113 6 46 98 99 34 54 8 1 60 54 10 1 248 48 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 27AUG2012 CHK 27AUG2012 APVD 27AUG2012 K.HUANG S.XI S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151478 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV G 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2151478 -1 G FINE CRIMP HEIGHT ADJUST MECHANICAL 2- 2151478 -2 G FINE CRIMP HEIGHT ADJUST PNEUMATIC 4- 2151478 -2 G FINE CRIMP HEIGHT ADJUST 7- 2151478 -7 G CRIMP TOOLING KIT REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - DOUBLE ACTING PNEUMATIC WITH 7 SENSORS - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE - TYPE - F SP 1.40 mm [.055] 1.83 mm [.072] APPLICATOR INSTRUCTIONS 408-35042 1 1 3 - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION MCON-1.2 LL TERMINAL NAME: WIRE STRIP LENGTH 3.30-3.90 mm [.130-.154 IN] TERMINAL APPLICATION SPECIFICATION n 5 - TERMINALS APPLIED TE TERMINAL 1563888-1 114-18464 INSULATION DIAMETER RANGE 1.40-1.60 mm [.055-.063 IN] - 6 - TE TERMINAL C1__DWG_PN_2_0 C1__DWG_PN_3_0 TE TERMINAL WIRE SIZE 0.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 0.86+/-0.03 [.034+/-.001] 4 CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 7.8 1 B 2 7 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 3 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - MAXIMUM INSULATION CRIMP WIDTH 2.05mm & MAXIMUM INSULATION CRIMP HEIGHT 2.05mm. SEE APPLICATION SPECIFICATION TO CLARIFY. - 5 6 7 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. TERMINAL LUBRICANT IS RECOMMENDED. THIS APPLICATOR IS EQUIPPED WITH THE DOUBLE ACTING FEED WITH SENSORS AND IS APPLICATION SPECIFIC. IT DOES NOT REQUIRE ITEMS 49 & 151. 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 1 1 ENTRY LEVEL APPLICATOR A PART NUMBER 8-2151478-1 8-2151478-2 9-2151478-1 9-2151478-2 AMP 4805 REV 31MAR2000 ITEM SUBSTITUTION LIST SAME AS ITEM ITEM DESCRIPTION 2151478-1 1 WIRE CRIMPER 2151478-2 2-2151478-1 2-2151478-2 3 46 141 INSULATION CRIMPER BASIC SUB -ASSEMBLY BASIC SUB -ASSEMBLY LUBRICATOR SUBSTITUTE PART NUMBER 3-1803530-3 1-1803623-5 1803940-9 1-1803940-0 DELETE 1 1 1 1 1 1 1 1 1 - 1 - 1 - 1 1 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 1 2 1 1 - 1 2 1 - 1 1 2 - 1 1 1 - 2 1 1 - 2 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 2 - 1 - 1 1 - - 1 1 - - 1 1 1 - 2 1 1 - 1 2 1 - 1 1 2 - 2 1 1 - 1 2 1 - W1__FA_SETTING_1 1 1 2 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - C1__DWG_PN_1_1 1 1 1 - C1__DWG_PN_4_0 1 1 1 - 1 1 1 - 1 1 1 - 4 - 1 - 1 4 - - - 1 4 - - 1 1 - - REF REF - - 1 1 REF - 1 - - - 6 TE TERMINAL C1__DWG_PN_1_0 7 1 1 - - 1 1 1 - 1 1 1 2844950-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119791-5 2119740-1 2168078-1 5-18022-5 1338685-1 2168083-8 5018030-1 811242-5 690753-2 18023-9 2119652-1 1803602-1 7-1752356-7 2079383-5 2-2844962-6 2844992-2 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-3 1333231-9 240641-4 2119757-8 238011-9 1-1633989-5 3-456402-3 - 1 1 - C - 1 1 - 1 - 1 - 1 1 PART NO -77 -42 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - AIR FEED MODULE CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 16 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION, SPECIAL SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION, SPECIAL CRIMPER, WIRE PREMIUM DWN 27AUG2012 CHK 27AUG2012 APVD 27AUG2012 K.HUANG S.XI S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119791-5 1 2119740-1 2 2168078-1 1 5-18022-5 1 1338685-1 2 2168083-8 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 1803602-1 1 7-1752356-7 2 2079383-5 2 2-2844962-6 1 2844992-2 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-3 1 1333231-9 1 240641-4 .. 1 ITEM_6 1 2119757-8 1 238011-9 1 1-1633989-5 .. 1 ITEM_2 1 3-456402-3 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764_APP 290 244 243 242 241 239 238 164 151 144 143 142 141 140 113 99 98 82 71 70 67 66 59 56 53 52 51 50 49 48 41 34 33 30 29 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-9 DESCRIPTION PRODUCT SPEC - 1 2844950-1 Ocean Side Feed Applicator - DRAWING NO 2151478 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV G C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE DATE DWN APVD - - - MECHANICAL A D 239 140 PNEUMATIC 59 D 2 244 56 243 A 238 53 242 2 3 59 50 4.0 REF 8 0.5 7 34 REF SEE DETAIL A 82 56 1 52 C FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) TERMINAL SUPPORT LOCATION 1 C 51 3 1 4 70 140 REF 5 35.58 41 0.05 DETAIL A 164 66 2 67 33 DOUBLE ACTING PNEUMATIC WITH SENSORS RAM SET-UP A 24 290 B A 19 20 30 B 9 21 59 29 1 12 241 13 SEE DETAIL A 30mm STROKE 56 CAM POSITIONS 30mm STROKE 1 30 REF REF 29 30mm STROKE 113 151 142 ITEM 30 LOCATED AT FRONT HOLES 6 141 98 99 34 143 8 1 144 143 10 1 20 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 49 MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 MECHANICAL PRE FEED 49 AIR FEED DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 27AUG2012 CHK 27AUG2012 APVD 27AUG2012 K.HUANG S.XI S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151478 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV G