8-2151497-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE F FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151497-1 F MECHANICAL AND CRIMP TOOLING KIT MECHANICAL F 7-2151497-2 F 7- 2151497 -7 A 3 2 LOC 2151497 -1 2151497 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST - PNEUMATIC CRIMP TOOLING KIT - - - D 3 - CRIMP WIRE INSUL SIZE - - TYPE - F F 0.69 mm [.027] 0.76 mm [.030] APPLICATOR INSTRUCTIONS 408-35042 - - - TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 1.00-1.20 mm [.039-.047 IN] C - TE CRIMP SPECIFICATION - 1.0 mm PITCH WIRE TO BOARD CONNECTOR TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION n 114-57020 - - INSULATION DIAMETER RANGE - 0.40-0.80 mm [.016-.031 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL 1734597-1 TE TERMINAL C1__DWG_PN_1_0 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 - TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_1_1 - WIRE SIZE 28 AWG 30 AWG 32 AWG 1 2 B 3 4 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.46+/-0.02 [.018+/-.001] 0.42+/-0.02 [.017+/-.001] 0.405+/-0.025 [.016+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 8.0 8.4 8.6 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - 4 - W1__FA_SETTING_1 3 W1__FA_SETTING_2 W1__FA_SETTING_3 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 - 1 - 1 1 1 - 1 1 1 1 A - 1 1 1 1 P LTR 1 1 1 1 1 - 1 1 - 2 - REF REF REF REF 1 - 1 1 - 1 1 - 1 1 1 1 2 1 1 2 1 - 1 1 2 - - 1 1 1 - - 1 1 1 - - 1 1 2 - 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 2 1 1 2 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 - 1 1 2 - 1 1 1 1 4 1 1 1 1 4 1 1 1 1 4 1 1 1 1 4 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 - 1 1 1 - 1 1 1 - 1 1 2 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - RK CT D ECR-19-001862 04FEB2019 LG CT E ECR-19-008600 31MAY2019 TB CT F ECR-20-007003 14MAY2020 TB GB SCR, BHSC, RoHS (M3 X 8) STABILIZER HOLDER, STABILIZER PUSH ROD, AIR FEED BUSHING, FLANGED FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE SCR, BHSC, RoHS (M3 X 6) LOCATER BLOCK,TERMINAL PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE STOCK DRAG ASSEMBLY STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER INSERT, SHEAR SPRING, COMPRESSION SCR, SKT HD CAP, RoHS, M4 X 10 SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 25OCT2011 CHK 26OCT2011 APVD 26OCT2011 HOFFNER T.ELBIN T.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 1803461 1 2119640-1 1 1803259-1 1 2119641-1 1 2119082-1 1 2079764 1 2119083 1 7-18023-7 1 2119580-1 1 2063440-1 2 1-2079383-0 1 2-1976053-3 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 2844908 1 2844907 1 690438-1 2 2168083-1 1 1-455888-9 1 1803607-1 1 2-2119791-2 1 2119740-1 2 2168078-1 2 2-18032-5 1 2168083-2 1 5-18022-5 1 1338685-1 4 2168083-3 1 1-5018030-0 1 1901681-4 1 1-1752354-2 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-3 1 1803602-1 1 2-1752356-5 2 2079383-5 2 2-2844962-3 1 2844992-3 1 455888-3 2 22283-1 1 356835-1 1 679754-1 1 1320928-2 1 980371-4 1 2168083-2 2 1-18028-2 1 1803213-1 1 2119806 1 SIMP_3-22280-3 1 1-2168083-0 1 2119805-1 1 1803095-6 1 3-1633711-7 .. 1 ITEM_7 .. 1 ITEM_6 1 1-2119757-9 1 238011-6 1 1633962-1 1 455888-1 1 1-1633713-8 284 283 282 250 249 248 244 243 242 241 239 238 230 179 177 176 175 174 172 164 163 137 136 99 98 96 95 82 71 70 67 66 61 60 59 56 54 52 51 50 49 48 47 46 44 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 1633289-4 TE Connectivity APPLICATION SPEC - 1 2079383-1 DESCRIPTION PRODUCT SPEC - APVD 09MAR2015 PART NO 1 DWN ECR-15-003793 -1 1 DATE C 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 - 2 1 1 1 1 2 1 1 - - 2 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 - 1 - 1 1 1 - 1 1 1 DESCRIPTION 2079383-1 1633289-4 1803461 2119640-1 1803259-1 2119641-1 2119082-1 2079764-1 2119083-1 7-18023-7 2119580-1 2063440-1 1-2079383-0 2-1976053-3 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994970-2 240638-1 3-23627-7 2119799-1 2844908-1 2844907-1 690438-1 2168083-1 1-455888-9 1803607-1 2-2119791-2 2119740-1 2168078-1 2-18032-5 2168083-2 5-18022-5 1338685-1 2168083-3 1-5018030-0 1901681-4 1-1752354-2 18023-9 2119652-1 2119653-1 1803583-9 1803515-3 1803602-1 2-1752356-5 2079383-5 2-2844962-3 2844992-3 455888-3 22283-1 356835-1 679754-1 1320928-2 980371-4 2168083-2 1-18028-2 1803213-1 2119806-1 3-22280-3 1-2168083-0 2119805-1 1803095-6 3-1633711-7 1-2119757-9 238011-6 1633962-1 455888-1 1-1633713-8 1 -77 -72 -71 -2 AMP 4805 REV 31MAR2000 66 PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT APPLICATOR DATA REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 Ocean Side Feed Applicator - DRAWING NO 2151497 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 56 44 PNEUMATIC 250 2 2 244 249 243 A 8 238 242 3 34 REF 163 59 82 1 136 137 C 2 REF 1 2 172 0.0 3 1 C 4 70 177 56 TERMINAL SUPPORT LOCATION 5 28 2 176 2 2 164 24 6 41 174 44 175 179 52 230 51 33 282 44.99 50 16.2 284 67 2 0.05 283 66 REF 0.5 30 A 95 B 50 REF RAM AND HOLDDOWN SET-UP 19 B 20 96 9 21 29 12 27 241 61 13 CAM POSITIONS 47 ITEM 30 LOCATED AT FRONT HOLES 29 REF REF 1 30mm STROKE 25 26 23 46 98 99 34 54 8 1 60 54 10 1 20 248 48 30 11 30mm STROKE 30mm STROKE 1 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 25OCT2011 CHK 26OCT2011 APVD 26OCT2011 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151497 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151497 -1 F FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151497 -7 A CRIMP TOOLING KIT - F 3 2 LOC PART NUMBER 2- 2151497 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST - 1 - APPLICATOR INSTRUCTIONS 408-35042 WIRE STRIP LENGTH 1.00-1.20 mm [.039-.047 IN] C TERMINAL APPLICATION SPECIFICATION 114-57020 - - - - - TE TERMINAL 1734597-1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 1 - 28 AWG 30 AWG 32 AWG W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.46+/-0.02 [.018+/-.001] 0.42+/-0.02 [.017+/-.001] 0.405+/-0.025 [.016+/-.001] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 8.0 8.4 8.6 B 2 3 4 RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 2 - 1 1 1 1 1 2 2 2 - 2 1 - 1 1 - 1 2 - 2 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 2 - 2 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 - - - - - - 1 - 1 1 1 1 - A 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50. 2 1 - 1 1 2 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 3 1 1 - W1__FA_SETTING_3 - 1 - W1__FA_SETTING_2 - 1 - W1__FA_SETTING_1 1 1 - 4 1 1 - CRIMP HEIGHT REFERENCE SETTING 1 1 - CRIMP HEIGHT mm [INCH] 4 - - WIRE SIZE 1 4 - TE TERMINAL - 1 - C1__DWG_PN_1_1 - 1 - C1__DWG_PN_4_0 - REF REF TE TERMINAL C1__DWG_PN_1_0 1 2 - TERMINALS APPLIED 1 1 - 0.40-0.80 mm [.016-.031 IN] 1 1 - n 1 1 - INSULATION DIAMETER RANGE 1 1 - 1.0 mm PITCH WIRE TO BOARD CONNECTOR 2 1 - TERMINAL NAME: - 2 - TE CRIMP SPECIFICATION 1 1 - TE TERMINAL 1 - - TERMINAL DATA: 1 1 - F F 1 1 - 0.76 mm [.030] 1 1 - 0.69 mm [.027] - 1 - TYPE - 1 3 1 1 D 1 1 - WIRE INSUL 1 1 1 1 1 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - SCR, BHSC, RoHS (M3 X 8) STABILIZER HOLDER, STABILIZER PUSH ROD, AIR FEED BUSHING, FLANGED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE SCR, BHSC, RoHS (M3 X 6) LOCATER BLOCK,TERMINAL PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT COUNTER, MAGNETIC SPRING, FEED FINGER FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE STOCK DRAG ASSEMBLY STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER INSERT, SHEAR SPRING, COMPRESSION SCR, SKT HD CAP, RoHS, M4 X 10 SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -22 -21 AMP 4805 REV 31MAR2000 LTR 2079383-1 1633289-4 1803461 2119640-1 1803259-1 2119082-1 2079764-1 2119083-1 7-18023-7 2119580-1 2063440-1 1-2079383-0 2-1976053-3 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994970-2 240638-1 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 3-23627-7 2119799-1 2844908-1 2844907-1 690438-1 2168083-1 1-455888-9 1803607-1 2-2119791-2 2119740-1 2168078-1 2-18032-5 5-18022-5 1338685-1 1-5018030-0 1901681-4 1-1752354-2 18023-9 2119652-1 1803602-1 2-1752356-5 2079383-5 2-2844962-3 2844992-3 455888-3 22283-1 356835-1 679754-1 1320928-2 980371-4 2168083-2 1-18028-2 1803213-1 2119806-1 3-22280-3 1-2168083-0 2119805-1 1803095-6 3-1633711-7 1-2119757-9 238011-6 1633962-1 455888-1 1-1633713-8 1 1 - SIZE P - PNEUMATIC - CRIMP 66 - - APPLICATOR DATA REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 DWN 25OCT2011 CHK 26OCT2011 APVD 26OCT2011 HOFFNER T.ELBIN T.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119640-1 1 1803259-1 1 2119082-1 1 2079764 1 2119083 1 7-18023-7 1 2119580-1 1 2063440-1 2 1-2079383-0 1 2-1976053-3 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 COUNTER_994970 1 240638 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 3-23627-7 1 2119799 1 2844908 1 2844907 1 690438-1 2 2168083-1 1 1-455888-9 1 1803607-1 1 2-2119791-2 1 2119740-1 2 2168078-1 2 2-18032-5 1 5-18022-5 1 1338685-1 1 1-5018030-0 1 1901681-4 1 1-1752354-2 3 18023-9 1 2119652 1 1803602-1 1 2-1752356-5 2 2079383-5 2 2-2844962-3 1 2844992-3 1 455888-3 2 22283-1 1 356835-1 1 679754-1 1 1320928-2 1 980371-4 1 2168083-2 2 1-18028-2 1 1803213-1 1 2119806 1 SIMP_3-22280-3 1 1-2168083-0 1 2119805-1 1 1803095-6 1 3-1633711-7 .. 1 ITEM_7 .. 1 ITEM_6 1 1-2119757-9 1 238011-6 1 1633962-1 1 455888-1 1 1-1633713-8 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 1803461 284 283 282 250 249 244 243 242 241 239 238 230 179 177 176 175 174 172 164 163 151 144 143 142 141 140 137 136 99 98 96 95 82 71 70 67 66 61 59 56 52 51 50 49 48 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 1633289-4 DESCRIPTION PRODUCT SPEC - 1 2079383-1 Ocean Side Feed Applicator - DRAWING NO 2151497 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 D 2 244 56 243 PNEUMATIC 250 242 2 2 3 249 8 REF 34 REF 238 A 163 59 0.0 136 TERMINAL SUPPORT LOCATION 82 137 C 177 172 56 2 2 2 1 1 2 3 176 C 1 4 70 174 5 28 282 175 41 179 140 REF 35.96 52 230 51 33 3 24 0.05 283 66 50 16.2 284 67 164 2 30 50 A 95 B 20 B 21 9 29 241 29 ITEM 30 LOCATED AT FRONT HOLES REF 30 REF 61 11 30mm STROKE 30mm STROKE 142 1 12 27 30mm STROKE REF RAM AND HOLDDOWN SET-UP 19 96 CAM POSITIONS 0.5 20 151 25 48 26 23 141 98 99 34 143 8 1 144 143 10 1 13 FEED TRACK POSITION GUIDE BY INSULATION BARREL 1 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 25OCT2011 CHK 26OCT2011 APVD 26OCT2011 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151497 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F