8-2151570-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE C FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151570-1 C MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151570-2 D 7- 2151570 -7 A D 3 2 LOC 2151570 -1 2151570 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD A RELEASED 13AUG2012 YY SX B ECR-17-009432 28JUNE2017 TB TE C ECR-18-006896 04MAY2018 TB JDG D ECR-19-010979 12JUL2019 FZ TE PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE - TYPE - F O 2.54 mm [.100] 4.19 mm [.165] APPLICATOR INSTRUCTIONS 408-35042 - 3 - TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 4.50-5.10 mm [.177-.201 IN] C TE CRIMP SPECIFICATION MCON 2.8-RECEPTACLE-SWS TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION 114-18718 n 7 - - INSULATION DIAMETER RANGE - - 2.20-3.00 mm [.087-.118 IN] - - - - - 5 - TERMINALS APPLIED TE TERMINAL 1670804-1 TE TERMINAL 1670804-3 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE SEAL 828905-1 - TE SEAL C1__DWG_PN_3_0 - C1__DWG_PN_4_0 - C1__DWG_PN_3_1 - WIRE SIZE 2.50mm2 7 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 1.83+/-0.05 [.072+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 12.2 - 8 4 - W1__FA_SETTING_1 - 1 2 3 4 B 5 - RECOMMENDED SPARE PARTS REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 8 - AP PLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - TERMINAL LUBRICANT IS RECOMMENDED. 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 7 - 3 TO BE USED ONLY FOR ACOME-CABLE WITH WIRE SIZE 2.5mm APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 2 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. - 1 - 1 - 1 1 1 - 1 1 1 1 A - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 2 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 & 4 of 4) MATERIAL - 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, BHSC, RoHS (M3 X 6) SCR, SKT HD CAP, RoHS, M4 X 12.0 LOCATER BLOCK,TERMINAL NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .100 DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 12JUN2012 CHK 12JUN2012 APVD 12JUN2012 Y.YIN G.BAILEY S.XI - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2079764 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 1 COUNTER_994970 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 2 1-2079383-0 4 2168083-3 1 1976053-2 1 1-5018030-0 1 1901681-8 1 1-1752354-9 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-3 1 1803602-1 1 1752356-3 2 2079383-5 2 2-2844962-8 1 2844992-1 1 455888-4 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 3-1633133-2 .. 1 ITEM_7 .. 1 ITEM_6 1 2119781-5 1 2-238011-1 1 1-1633996-3 1 1-455888-3 1 456407-5 248 244 243 242 241 239 238 177 176 175 174 164 119 113 99 98 82 71 67 66 60 59 57 56 55 54 53 52 51 50 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119082-9 TE Connectivity APPLICATION SPEC - 1 2119641-1 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH PART NO 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. mm -1 1 -77 -72 -71 -2 DIMENSIONS: 1 1 1 1 2 1 1 2 1 - 1 1 2 - - 1 1 1 - - 1 1 1 - - 1 1 2 - 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 1 1 1 4 1 1 1 2 4 1 1 1 2 4 1 1 1 2 4 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 REF REF 1 1 1 1 REF 1 1 1 1 REF 1 1 1 1 - 1 1 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 2119641-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 993111-1 8-22280-7 1752353-2 1901680-2 994970-2 1-18028-2 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338685-1 1-2079383-0 2168083-3 1976053-2 1-5018030-0 1901681-8 1-1752354-9 18023-9 2119652-1 2119653-1 1803583-9 1803515-3 1803602-1 1752356-3 2079383-5 2-2844962-8 2844992-1 455888-4 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 3-1633133-2 2119781-5 2-238011-1 1-1633996-3 1-455888-3 456407-5 - Ocean Side Feed Applicator - DRAWING NO 2151570 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 56 44 2 2.3 REF PNEUMATIC 244 243 242 A 2 3 238 REF 8 82 59 1 2 3 177 SEE DETAIL A C 1 4 2 176 2 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 53 TERMINAL SUPPORT LOCATION 28 5 41 175 174 44 52 43.29 55 3 DETAIL A 33 17.9 67 57 8 RAM AND HOLDDOWN SET-UP 19 30 20 29 21 B 9 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 CAM POSITIONS 13 47 30 REF 29 REF 1 11 30mm STROKE 30mm STROKE 30mm STROKE 119 113 5 46 98 99 34 54 8 1 60 54 10 1 248 48 0.5 50 REF A 24 B 2 50 REF 0.05 66 51 164 0.5 34 REF 1 C 56 4.3 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 12JUN2012 CHK 12JUN2012 APVD 12JUN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151570 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV D 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION REVISION DESCRIPTION FEED TYPE 2- 2151570 -1 C FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151570 -7 A CRIMP TOOLING KIT - D 4 3 2 LOC PART NUMBER 2- 2151570 -2 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F O 2.54 mm [.100] 4.19 mm [.165] APPLICATOR INSTRUCTIONS 408-35042 - 1 - 1 - 3 MCON 2.8-RECEPTACLE-SWS TERMINAL NAME: WIRE STRIP LENGTH 4.50-5.10 mm [.177-.201 IN] C TERMINAL APPLICATION SPECIFICATION 114-18718 n 7 - - - - - TE TERMINAL 1670804-1 1670804-3 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE SEAL C1__DWG_PN_3_0 - 1 - 828905-1 2.50mm2 CRIMP HEIGHT mm [INCH] 7 W1__DWG_WGAUGE_1 1.83+/-0.05 [.072+/-.002] W1__DWG_CRIMP_HT_1 12.2 - - 4 5 7 8 TO BE USED ONLY FOR ACOME-CABLE WITH WIRE SIZE 2.5mm APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 1 1 1 1 1 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 - - - - - - 1 - 1 1 1 1 - A 1 1 - 1 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 1 1 1 - 1 2 - - 1 1 1 - 2 1 1 - 1 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 2 1 - TERMINAL LUBRICANT IS RECOMMENDED. 1 2 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 1 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 1 - 3 2 1 - B 1 2 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - 3 1 1 - 8 1 1 - W1__FA_SETTING_1 1 1 - 4 1 1 - CRIMP HEIGHT REFERENCE SETTING 1 1 - WIRE SIZE 4 - 5 1 4 - TE SEAL - 1 - C1__DWG_PN_3_1 1 REF REF - C1__DWG_PN_4_0 1 1 TE TERMINAL C1__DWG_PN_1_0 1 1 - TERMINALS APPLIED 1 1 - 2.20-3.00 mm [.087-.118 IN] - 1 - INSULATION DIAMETER RANGE 1 1 - TE CRIMP SPECIFICATION 1 - - TE TERMINAL 1 1 - TERMINAL DATA: 1 1 - 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 993111-1 8-22280-7 1752353-2 1901680-2 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2119955-1 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 5-18022-5 985575-3 1338685-1 1-2079383-0 1976053-2 1-5018030-0 1901681-8 1-1752354-9 18023-9 2119652-1 1803602-1 1752356-3 2079383-5 2-2844962-8 2844992-1 455888-4 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 3-1633133-2 2119781-5 2-238011-1 1-1633996-3 1-455888-3 456407-5 1 1 1 1 1 1 PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 12JUN2012 CHK 12JUN2012 APVD 12JUN2012 Y.YIN G.BAILEY S.XI - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338685-1 2 1-2079383-0 1 1976053-2 1 1-5018030-0 1 1901681-8 1 1-1752354-9 3 18023-9 1 2119652 1 1803602-1 1 1752356-3 2 2079383-5 2 2-2844962-8 1 2844992-1 1 455888-4 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 3-1633133-2 .. 1 ITEM_7 .. 1 ITEM_6 1 2119781-5 1 2-238011-1 1 1-1633996-3 1 1-455888-3 1 456407-5 244 243 242 241 239 238 177 176 175 174 164 151 144 143 142 141 140 119 113 99 98 82 71 67 66 59 57 56 55 53 52 51 50 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2079764 TE Connectivity APPLICATION SPEC - 1 2119082-9 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, BHSC, RoHS (M3 X 6) LOCATER BLOCK,TERMINAL NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .100 DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean Side Feed Applicator - DRAWING NO 2151570 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 D 2 244 2.3 REF 56 243 PNEUMATIC 242 A 2 3 4.3 238 8 0.5 REF 59 34 82 C 56 1 1 C 177 SEE DETAIL A 2 2 2 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) TERMINAL SUPPORT LOCATION 2 176 3 175 1 4 28 174 5 140 41 52 34.26 55 53 DETAIL A 164 33 3 50 57 A 20 B 9 21 29 1 12 241 13 CAM POSITIONS ITEM 30 LOCATED AT FRONT HOLES 1 30 REF REF 29 30mm STROKE 30mm STROKE 142 REF RAM AND HOLDDOWN SET-UP 19 30 30mm STROKE 0.5 8 50 24 B 17.9 67 2 REF 0.05 66 51 REF 151 113 48 5 141 98 99 34 143 8 1 144 143 10 1 119 FEED TRACK POSITION GUIDE BY INSULATION BARREL 11 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 12JUN2012 CHK 12JUN2012 APVD 12JUN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151570 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D