8-2151692-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION 2 FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151692-1 B MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151692-2 C 7- 2151692 -7 A FINE CRIMP HEIGHT ADJUST 1 REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER FEED TYPE B C 3 LOC 2151692 -1 2151692 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 66 P LTR PNEUMATIC AND CRIMP TOOLING KIT DATE DWN APVD RELEASED 04SEP2012 LG GB A1 ECR-14-008728 11JUN2014 KH UG B ECR-19-006860 30APR2019 LG TE C ECR-20-013523 23SEP2020 FZ TE A PNEUMATIC DESCRIPTION PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE 1.57 mm [.062] TYPE 3.94 mm [.155] APPLICATOR INSTRUCTIONS 408-35042 F O TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION MICRO POWER QUADLOK SOCKET CONTACT, SWS TERMINAL NAME: WIRE STRIP LENGTH - TERMINAL INSULATION DIAMETER RANGE 3.50-4.10 mm [.138-.161 IN] C - TERMINAL APPLICATION SPECIFICATION n 114-18141-1 114-18141-10 6 - 3.4mm MAX [.134 IN MAX] - 3 - - 968681-2 968681-5 WIRE SIZE 0.50mm2 0.35mm2 TE TERMINAL 1-968681-5 C1__DWG_PN_1_0 C1__DWG_PN_1_1 2-968681-5 C1__DWG_PN_1_2 C1__DWG_PN_2_0 - TE SEAL - TE SEAL 967610-1 C1__DWG_PN_3_0 C1__DWG_PN_2_1 - TERMINALS APPLIED TE TERMINAL 968680-2 - C1__DWG_PN_4_0 C1__DWG_PN_4_1 - SEAL INSULATION DIAMETER RANGE 1.4-2.1 mm - C1__DWG_PN_2_2 - C1__DWG_PN_1_3 - CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 1.15+/-0.03 [.045+/-.001] 1.08+/-0.03 [.043+/-.001] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 6.6 7.4 - 4 - W1__FA_SETTING_1 5 W1__FA_SETTING_2 - 1 2 3 B 4 5 6 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - CRIMPER & ANVIL DIMENSIONS CONFORM WITH 114-18141-10 SPEC. - 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 1 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. A 1 - 1 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 - 1 1 2 1 - 1 1 1 1 - 1 1 1 1 - 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 3 1 1 1 1 3 1 1 1 1 3 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 2 1 1 - 4 2 2 - 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 mm & 4 of 4) MATERIAL - PART NO 1 -77 -72 -71 -2 DIMENSIONS: -1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 2119641-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 1-18028-2 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338685-1 2168083-3 1-18023-1 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1-1752356-8 2079383-5 2-2844962-1 2844992-2 1-455888-0 1320928-1 2168083-2 1-18028-2 2119533-3 879657-2 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1-1633129-9 240641-5 2119781-1 2-238011-1 3-1633965-7 1-455888-8 9-657555-1 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP M4 X 10.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED HOLD DOWN INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .062 SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 29JUN2012 CHK 29JUN2012 APVD 29JUN2012 Y.YIN G.BAILEY S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 1-18028-2 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 4 2168083-3 2 1-18023-1 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1-1752356-8 2 2079383-5 2 2-2844962-1 1 2844992-2 1 1-455888-0 1 1320928-1 1 2168083-2 3 1-18028-2 1 2119533-3 1 879657-2 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1-1633129-9 1 240641-5 .. 1 ITEM_6 1 2119781-1 1 2-238011-1 1 3-1633965-7 1 1-455888-8 1 9-657555-1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764 248 244 243 242 241 239 238 164 119 99 98 82 71 67 66 60 59 57 56 54 53 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 18 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-9 DESCRIPTION PRODUCT SPEC - 1 2119641-1 Ocean Side Feed Applicator - DRAWING NO 2151692 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 REF 5 D 59 56 44 PNEUMATIC 2 57 REF 2.6 REF SHEAR DEPRESSOR DETAIL 244 53 A 243 20 18 238 242 C 3 8 7 59 2 82 1 REF 1.3 0.5 34 REF 1 C 2 SEE DETAIL A 3 1 56 4 TERMINAL SUPPORT LOCATION 28 5 41 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 44 44.69 REF 0.05 66 2 164 DETAIL A 33 57 5 RAM SET-UP A 24 B 67 19 30 20 29 21 B 9 ITEM 30 LOCATED AT FRONT HOLES 1 12 241 CAM POSITIONS 13 47 1 11 30mm STROKE 30mm STROKE 30mm STROKE 30 REF 29 REF 119 98 99 46 34 54 8 1 60 54 10 1 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 29JUN2012 CHK 29JUN2012 APVD 29JUN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151692 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV C 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151692 -1 B FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151692 -7 A CRIMP TOOLING KIT - C 3 2 LOC PART NUMBER 2- 2151692 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE 1.57 mm [.062] TYPE 3.94 mm [.155] APPLICATOR INSTRUCTIONS 408-35042 F O TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH TERMINAL APPLICATION SPECIFICATION n 114-18141-1 114-18141-10 6 - - - TE TERMINAL 968680-2 968681-2 968681-5 WIRE SIZE 0.50mm2 0.35mm2 TE TERMINAL C1__DWG_PN_1_0 1-968681-5 2-968681-5 C1__DWG_PN_1_1 C1__DWG_PN_1_2 C1__DWG_PN_2_0 TE SEAL C1__DWG_PN_3_0 TE SEAL 967610-1 C1__DWG_PN_2_1 C1__DWG_PN_4_1 1 - W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 1.15+/-0.03 [.045+/-.001] 1.08+/-0.03 [.043+/-.001] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 6.6 7.4 B 3 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 5 6 1 1 1 1 - 1 1 - 1 3 - 3 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 - 1 1 1 1 1 - 1 1 - 1 - - - 1 - 1 1 1 1 - A 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 1 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 2 - - 1 2 1 - 1 1 2 - 1 1 1 - 1 1 1 - 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 2 1 - CRIMPER & ANVIL DIMENSIONS CONFORM WITH 114-18141-10 SPEC. 1 2 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - 5 1 1 - W1__FA_SETTING_2 1 1 W1__FA_SETTING_1 1 1 - 4 4 - - CRIMP HEIGHT REFERENCE SETTING 1 4 - CRIMP HEIGHT mm [INCH] - 1 - C1__DWG_PN_1_3 - REF REF - C1__DWG_PN_2_2 1 1 - C1__DWG_PN_4_0 1 - - SEAL INSULATION DIAMETER RANGE 1.4-2.1 mm 1 1 - TERMINALS APPLIED 1 1 - 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2844908-1 2844907-1 455888-5 1803607-3 2119740-1 2168078-1 5-18022-5 985575-3 1338685-1 1-18023-1 18023-9 2119652-1 1803602-1 1-1752356-8 2079383-5 2-2844962-1 2844992-2 1-455888-0 1320928-1 2168083-2 1-18028-2 2119533-3 879657-2 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1-1633129-9 240641-5 2119781-1 2-238011-1 3-1633965-7 1-455888-8 9-657555-1 1 1 - 3 3.4mm MAX [.134 IN MAX] - 1 - TERMINAL INSULATION DIAMETER RANGE 3.50-4.10 mm [.138-.161 IN] C - MICRO POWER QUADLOK SOCKET CONTACT, SWS TERMINAL NAME: 1 1 1 1 1 PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP M4 X 10.0 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED HOLD DOWN INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .062 SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 29JUN2012 CHK 29JUN2012 APVD 29JUN2012 Y.YIN G.BAILEY S.XI NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2844908 1 2844907 1 455888-5 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338685-1 2 1-18023-1 3 18023-9 1 2119652 1 1803602-1 1 1-1752356-8 2 2079383-5 2 2-2844962-1 1 2844992-2 1 1-455888-0 1 1320928-1 1 2168083-2 3 1-18028-2 1 2119533-3 1 879657-2 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1-1633129-9 1 240641-5 .. 1 ITEM_6 1 2119781-1 1 2-238011-1 1 3-1633965-7 1 1-455888-8 1 9-657555-1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119083 244 243 242 241 239 238 164 151 144 143 142 141 140 119 99 98 82 71 67 66 59 57 56 53 49 48 41 34 33 30 29 28 24 21 20 19 18 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079764 DESCRIPTION PRODUCT SPEC - 1 2119082-9 Ocean Side Feed Applicator - DRAWING NO 2151692 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL 140 A D 2 53 239 D 243 20 18 59 242 2 3 2.6 REF 7 56 PNEUMATIC REF 5 244 57 REF SHEAR DEPRESSOR DETAIL 82 A 1 1 238 2 3 59 4 28 0.5 34 REF REF 8 1 1.3 5 41 TERMINAL SUPPORT LOCATION C C SEE DETAIL A 56 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 164 33 66 67 35.66 140 0.05 REF 20 30 DETAIL A 5 19 A 24 57 9 21 29 1 12 RAM SET-UP 241 13 1 B B ITEM 30 LOCATED AT FRONT HOLES CAM POSITIONS 30mm STROKE 98 141 34 143 8 1 144 143 10 1 119 30 11 REF REF 29 30mm STROKE 30mm STROKE 142 99 151 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 29JUN2012 CHK 29JUN2012 APVD 29JUN2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151692 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C