8-2151730-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION 2 FEED TYPE FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151730-1 F MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151730-2 F 7- 2151730 -7 A FINE CRIMP HEIGHT ADJUST CRIMP TOOLING KIT 3 WIRE INSUL - - - - TYPE - F O 2.03 mm [.080] 4.25 mm [.167] APPLICATOR INSTRUCTIONS 408-35042 - TE TERMINAL TERMINAL DATA: 2.8mm BLADE, SEALED TERMINAL NAME: WIRE STRIP LENGTH 5.50-5.51 mm [.217-.217 IN] C TERMINAL APPLICATION SPECIFICATION n 114-13013 - - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 1.20-2.70 mm [.047-.106 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL 1326031-8 TE TERMINAL 1326032-9 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE SEAL 1949064-1 1949064-2 C1__DWG_PN_3_0 C1__DWG_PN_3_1 YAZAKI SEAL 7158-3113-40 7158-3112-70 - SEAL INSULATION DIAMETER RANGE C1__DWG_PN_4_0 - 1.2-2.7 mm - 1.2-2.7 mm 5 - WIRE SIZE 18 AWG 1.00mm2 0.75mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.37+/-0.05 [.054+/-.002] 1.30+/-0.05 [.051+/-.002] 1.22+/-0.05 [.048+/-.002] - CRIMP HEIGHT 4 REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 4.1 4.9 6.0 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - 1 2 3 B 4 5 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 1 1 - 1 1 1 1 A - 1 1 1 1 LTR DESCRIPTION DATE DWN APVD E ECR-19-014658 20SEP2019 FZ TE E1 ECR-20-002411 19FEB2020 MZ YY E2 ECR-21-006796 09JUL2021 FJ YY F ECR-22-130118 21FEB2022 FZ GB - 1 1 1 1 1 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - PART NO 1 1 - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 - 1 1 2 - - 1 1 1 - - 1 1 1 - - 1 1 2 - 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 2 1 1 2 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 - 1 1 2 - 1 1 1 1 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 2 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: -1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 2-455888-9 2119641-1 2119082-7 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 1-22281-8 318563-1 2844908-1 2844907-1 1-690438-0 2168083-1 2168083-6 1-455888-7 985575-1 224405-2 18024-6 1803096-1 1803607-3 2119740-1 2168078-1 2-18032-5 2168083-2 5-18022-5 985575-3 1338685-1 2168083-3 1-2168083-0 5018030-1 811242-5 690753-2 18023-9 2119652-1 2119653-1 1803583-9 1803515-2 1803602-2 2-1752356-0 2079383-5 1-2844962-8 2844938-5 455888-3 22283-1 356835-1 240792-2 1320928-6 980371-4 2168083-2 1-18028-2 2119533-2 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1-1633927-6 2119781-1 2-238011-1 6-2119784-2 1-455888-9 1-856313-7 1 -77 -72 -71 -2 AMP 4805 REV 31MAR2000 P - - SIZE 66 PNEUMATIC D CRIMP REVISIONS PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT APPLICATOR DATA 1 DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER F F 3 LOC 2151730 -1 2151730 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 TOLERANCES UNLESS OTHERWISE SPECIFIED: FINISH DWN 25JUL2012 CHK 25JUL2012 APVD 25JUL2012 Y.YIN G.BAILEY S.XI - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119082-7 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 SIMP_1-22281-8 1 318563-1 1 2844908 1 2844907 1 1-690438-0 2 2168083-1 1 2168083-6 1 1-455888-7 1 985575-1 1 224405-2 2 18024-6 1 1803096-1 1 1803607_3 1 2119740-1 2 2168078-1 2 2-18032-5 1 2168083-2 1 5-18022-5 1 985575-3 1 1338685-1 4 2168083-3 2 1-2168083-0 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-2 1 1803602-2 1 2-1752356-0 2 2079383-5 2 1-2844962-8 1 2844938-5 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-2 1 1320928-6 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533-2 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1-1633927-6 .. 1 ITEM_7 .. 1 ITEM_6 1 2119781-1 1 2-238011-1 1 6-2119784-2 1 1-455888-9 1 1-856313-7 259 248 244 243 242 241 239 238 164 121 119 99 98 96 95 93 82 81 80 79 78 71 67 66 61 60 59 57 56 54 53 52 51 50 49 48 47 46 44 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119641-1 TE Connectivity APPLICATION SPEC - 1 2-455888-9 DESCRIPTION PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES SPACER, CRIMPER FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC SPRING, COMPRESSION GUARD, FRONT CHIP SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SCR, FLT SKT HD CAP M3 X 6.0 DEPRESSOR, WIRE SCR, BTN SKT HD CAP (M4 X 8.0) EXTENSION PLATE DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 40) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE Ocean Side Feed Applicator - DRAWING NO 2151730 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE MECHANICAL DWN APVD - - - 239 A D DATE 5 REF D 59 2.0 REF 56 PNEUMATIC 44 57 REF 2 SHEAR DEPRESSOR DETAIL 244 53 A 243 238 242 50 82 SEE DETAIL A 81 80 1 2 3 1 4 51 56 C TERMINAL SUPPORT LOCATION FOR BLADE TERMINAL P/N 1326031-8 28 5.0 5 8 41 0.5 REF 34 REF TERMINAL SUPPORT LOCATION FOR RECEPTACLE TERMINAL P/N 1326032-9 66 DETAIL A 2 164 33 67 A 30 5 0.05 9 21 78 1 12 96 RAM SET-UP 241 13 29 ITEM 78 LOCATED AT FRONT HOLES 1 30 REF 29 REF 25 78 REF 11 30mm STROKE 30mm STROKE 119 27 61 26 23 121 93 46 98 99 34 54 8 1 60 54 10 1 FEED TRACK POSITION GUIDE BY WIRE BARREL 248 48 REF B 20 95 CAM POSITIONS 44 19 79 B 57 44.61 24 30mm STROKE REF 34 REF 52 47 3 0.5 259 1 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 8 59 C 8.0 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: FINISH 25JUL2012 CHK 25JUL2012 APVD 25JUL2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151730 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 3 2 DESCRIPTION FEED TYPE 2- 2151730 -1 F FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151730 -7 A CRIMP TOOLING KIT - FINE CRIMP HEIGHT ADJUST 1 - 4.25 mm [.167] APPLICATOR INSTRUCTIONS 408-35042 - 1 - WIRE STRIP LENGTH 5.50-5.51 mm [.217-.217 IN] C TERMINAL APPLICATION SPECIFICATION n 114-13013 - - - - - TE TERMINAL 1326031-8 TE TERMINAL C1__DWG_PN_1_0 1326032-9 C1__DWG_PN_1_1 TE SEAL PN C1__DWG_PN_2_0 1949064-1 1949064-2 C1__DWG_PN_2_1 C1__DWG_PN_3_0 C1__DWG_PN_3_1 YAZAKI PN 1.00mm2 0.75mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.37+/-0.05 [.054+/-.002] W1__DWG_CRIMP_HT_1 1.30+/-0.05 [.051+/-.002] W1__DWG_CRIMP_HT_2 1.22+/-0.05 [.048+/-.002] W1__DWG_CRIMP_HT_3 4.1 - 4.9 6.0 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 5 - ENTRY LEVEL APPLICATOR A SAME AS ITEM ITEM DESCRIPTION 2151730-1 1 WIRE CRIMPER SUBSTITUTE PART NUMBER 1-2370389-7 9-2151730-1 2-2151730-1 46 BASIC SUB -ASSEMBLY 1803940-9 8-2151730-2 9-2151730-2 2151730-2 2-2151730-2 3 141 INSULATION CRIMPER BASIC SUB -ASSEMBLY LUBRICATOR 6-1803604-2 1-1803940-0 DELETE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 - 1 1 1 1 1 - 1 - - - - - - 1 - 1 1 1 1 - 1 1 1 1 1 LTR DESCRIPTION DATE SEE SHEET 1 DWN APVD - - DIMENSIONS: PACIFIC VERSION mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - FINISH DWN 25JUL2012 CHK 25JUL2012 APVD 25JUL2012 Y.YIN G.BAILEY S.XI - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-2 1 SIMP_1-22281-8 1 318563-1 1 2844908 1 2844907 1 1-690438-0 2 2168083-1 1 2168083-6 1 1-455888-7 1 985575-1 1 224405-2 2 18024-6 1 1803096-1 1 1803607_3 1 2119740-1 2 2168078-1 2 2-18032-5 1 5-18022-5 1 985575-3 1 1338685-1 2 1-2168083-0 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 1803602-2 1 2-1752356-0 2 2079383-5 2 1-2844962-8 1 2844938-5 1 455888-3 2 SIMP_22283-1 1 356835-1 1 240792-2 1 1320928-6 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533-2 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1-1633927-6 .. 1 ITEM_7 .. 1 ITEM_6 1 2119781-1 1 2-238011-1 1 6-2119784-2 1 1-455888-9 1 1-856313-7 259 244 243 242 241 239 238 164 151 144 143 142 141 140 121 119 99 98 96 95 93 82 81 80 79 78 71 67 66 61 59 57 56 53 52 51 50 49 48 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119082-7 TE Connectivity APPLICATION SPEC - 1 2-455888-9 DESCRIPTION PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES SPACER, CRIMPER CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC SPRING, COMPRESSION GUARD, FRONT CHIP SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SCR, FLT SKT HD CAP M3 X 6.0 DEPRESSOR, WIRE SCR, BTN SKT HD CAP (M4 X 8.0) EXTENSION PLATE DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 40) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PART NO -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 1 1 - 1 1 1 - 1 2 1 - PART NUMBER 8-2151730-1 1 2 - 1 1 1 - 1 2 1 - ITEM SUBSTITUTION LIST 2 2 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 2 - 1 1 1 - 1 1 1 - 1 2 - - 6. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 - 1 1 1 - APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 1 - 4 2 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 1 2 - 3 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 2 1 - RECOMMENDED SPARE PARTS 2 2 - 1 1 2 - B 1 1 - W1__FA_SETTING_3 1 1 - W1__FA_SETTING_2 2 1 - W1__FA_SETTING_1 1 2 - 18 AWG 1 1 - 4 CRIMP HEIGHT REFERENCE SETTING 1 1 - CRIMP HEIGHT mm [INCH] 1 1 - WIRE SIZE 2 1 - 5 1 2 - 1.2-2.7 mm 1 1 - 1.2-2.7 mm 1 1 - 7158-3113-40 7158-3112-70 1 1 - C1__DWG_PN_4_0 1 1 - C1__DWG_PN_4_0 1 1 - SEAL INSULATION DIAMETER RANGE 1 1 - TERMINALS APPLIED 1 1 - 1.20-2.70 mm [.047-.106 IN] 4 - - INSULATION DIAMETER RANGE 1 4 - 2.8mm BLADE, SEALED - 1 - TERMINAL NAME: - REF REF - TE CRIMP SPECIFICATION 1 1 - TE TERMINAL 1 - - TERMINAL DATA: 1 1 - F O 2.03 mm [.080] 1 1 - TYPE 1 1 - 3 WIRE INSUL P 2-455888-9 2119082-7 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-2 1-22281-8 318563-1 2844908-1 2844907-1 1-690438-0 2168083-1 2168083-6 1-455888-7 985575-1 224405-2 18024-6 1803096-1 1803607-3 2119740-1 2168078-1 2-18032-5 5-18022-5 985575-3 1338685-1 1-2168083-0 5018030-1 811242-5 690753-2 18023-9 2119652-1 1803602-2 2-1752356-0 2079383-5 1-2844962-8 2844938-5 455888-3 22283-1 356835-1 240792-2 1320928-6 980371-4 2168083-2 1-18028-2 2119533-2 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1-1633927-6 2119781-1 2-238011-1 6-2119784-2 1-455888-9 1-856313-7 1 1 - SIZE 66 PNEUMATIC - CRIMP REVISIONS - D APPLICATOR DATA 1 DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER REVISION F 4 LOC PART NUMBER 2- 2151730 -2 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 Ocean Side Feed Applicator - DRAWING NO 2151730 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D REF 5 239 140 59 PNEUMATIC D 2.0 REF 2 244 57 243 REF SHEAR DEPRESSOR DETAIL 56 53 242 2 3 8.0 238 A REF 8 50 0.5 34 59 259 82 52 C SEE DETAIL A 81 80 REF TERMINAL SUPPORT LOCATION FOR BLADE TERMINAL P/N 1326031-8 1 51 C 1 5.0 2 3 56 1 8 0.5 REF 34 REF 4 28 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 5 41 TERMINAL SUPPORT LOCATION FOR RECEPTACLE TERMINAL P/N 1326032-9 164 66 2 DETAIL A 35.58 67 33 57 A 24 20 B 79 9 21 95 13 29 ITEM 78 LOCATED AT FRONT HOLES 30 1 REF REF 29 78 REF 25 30mm STROKE 30mm STROKE 142 1 241 96 30mm STROKE RAM SET-UP 12 78 CAM POSITIONS 5 19 30 B 140 REF 0.05 151 27 48 61 26 23 121 93 141 98 99 34 143 8 1 144 143 10 1 119 FEED TRACK POSITION GUIDE BY WIRE BARREL 11 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: FINISH 25JUL2012 CHK 25JUL2012 APVD 25JUL2012 Y.YIN G.BAILEY S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151730 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F