8-2151825-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 PART NUMBER REVISION DESCRIPTION FEED TYPE 2151825 -2 C FINE CRIMP HEIGHT ADJUST PNEUMATIC 7-2151825-2 C 7- 2151825 -7 A PNEUMATIC AND CRIMP TOOLING KIT A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 2 - 3 - WIRE INSUL - 7.11 mm [.280] APPLICATOR INSTRUCTIONS 408-35042 - C TERMINAL APPLICATION SPECIFICATION N.106.867 Rev 8 1 - TERMINALS APPLIED TE TERMINAL 2113306-1 C1__DWG_PN_1_1 TE TERMINAL C1__DWG_PN_3_0 LEAR TERMINAL 6.00mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 3.30+0.10/-0.05 [.130+.004/-.002] 3.00+/-0.05 [.118+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 5.0 7.7 5 6 7 A 1 1 1 1 1 2 2 1 1 1 1 1 - 1 1 - 1 1 - 1 1 1 1 2 - 1 - - - - - - 1 - 1 1 1 - 1 1 1 - 1 2 1 - 1 1 2 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 1 2 1 - 1 2 2 - 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 2 - 1 1 1 - RELOCATE ITEM 19 TO BACK OF APLICATOR. 1 1 - TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 1 1 - 1 - 1 - 7 - - - APPLICATOIN NOT RECOMMENDED IN PRESS WITH INSUFFICENT TONNAGE. 1 - - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 1 - 4 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. 2 1 - 3 1 2 - B 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 2 1 - RECOMMENDED SPARE PARTS 2 2 - 1 1 2 - 5 1 1 W1__FA_SETTING_2 1 1 W1__FA_SETTING_1 1 1 - 10.00mm2 1 1 - CRIMP HEIGHT 4 REFERENCE SETTING 1 1 - CRIMP HEIGHT mm [INCH] 2 1 - WIRE SIZE 1 2 - C1__DWG_PN_2_1 2 1 C1__DWG_PN_4_0 1 2 C1__DWG_PN_2_0 1 1 - 6 LEAR TERMINAL 28490306189 C1__DWG_PN_1_0 - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 REF REF - 4.10-6.00 mm [.161-.236 IN] 1 1 - 8.00-8.02 mm [.315-.316 IN] 1 1 - INSULATION DIAMETER RANGE 1 1 - WIRE STRIP LENGTH 1 1 - FLAT CONTACT 8x0.8/9.5x1.2 TERMINAL NAME: 1 1 - LEAR CRIMP SPECIFICATION - 1 - LEAR TERMINAL 1 - - TERMINAL DATA: 1 1 - F O 5.33 mm [.210] 1 1 - TYPE 1 1 3 1 1 D 2 1 - SIZE 1 1 1 2 - 1 1 1 2 1 -77 -72 -2 P LTR DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - 2168083-1 2119641-1 2119082-6 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-2 2-1752354-7 6-993111-6 8-22280-7 1752353-2 1901680-2 994970-2 1-22281-8 2168083-6 455888-6 318563-1 2844908-1 2844907-1 2-690438-2 2168083-1 1803078-1 2079383-4 1803096-1 1633782-3 1803607-3 1-2119791-2 2119943-1 2119740-1 2168078-1 2-18032-5 2168083-2 5-18022-5 1-1338683-1 2168083-3 1-5018030-0 1901681-2 18023-9 2119652-1 2119653-1 1-1803583-7 1803515-2 1803602-2 4-1752356-5 1-2079383-3 3-2844962-7 2844938-9 1-455888-0 22281-8 356835-1 240792-1 1320928-6 980371-4 2168083-2 1-18028-2 1803013-1 2119806-1 4-22280-7 1-356885-3 1-2119805-0 1-318059-0 2-1333229-3 1803080-1 238011-1 1-1803017-4 1-455888-4 456430-2 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. AMP 4805 REV 31MAR2000 66 DESCRIPTION DATE DWN APVD B ECR-15-014598 05OCT2015 MR JDG C ECR-22-153782 27SEP2022 JWC ROY - CRIMP REVISIONS DIST PNEUMATIC CRIMP TOOLING KIT APPLICATOR DATA 1 SCR, SKT HD CAP, RoHS, M3 X 8.0 FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC SPRING, COMPRESSION SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER GUARD, FRONT CHIP SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SPACER, PRECISION SCR, BHSC, RoHS (M4 X 8) EXTENSION PLATE FENCE DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 12.0 NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 40) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 25) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F SPACER, CRIMPER CRIMPER, WIRE DWN 19DEC2012 CHK 28DEC2012 APVD 28DEC2012 R.O.WILSON K.J.STAKEM T.L.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-2 1 2-1752354-7 1 6-993111-6 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 1 COUNTER_994970 1 1-22281-8 1 2168083-6 1 455888-6 1 318563-1 1 2844908 1 2844907 1 2-690438-2 2 2168083-1 1 1803078-1 2 2079383-4 1 1803096 1 1633782-3 1 1803607_3 1 1-2119791-2 1 2119943-1 1 2119740-1 2 2168078-1 2 2-18032-5 1 2168083-2 1 5-18022-5 1 1-1338683-1 2 2168083-3 1 1-5018030-0 1 1901681-2 3 18023-9 1 2119652 1 2119653 1 1-1803583-7_MOD 1 1803515-2 1 1803602-2 1 4-1752356-5 2 1-2079383-3 2 3-2844962-7 1 2844938-9 1 1-455888-0 2 SIMP_22281-8 1 356835-1 1 240792-1 1 1320928-6 1 980371-4 1 2168083-2 2 1-18028-2 1 1803013-1 1 2119806 1 SIMP_4-22280-7 1 1-356885-3 1 1-2119805-0 1 1-318059-0 1 2-1333229-3 .. 1 ITEM_7 .. 1 ITEM_6 1 1803080-1 1 238011-1 1 1-1803017-4 1 1-455888-4 1 456430-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119082-6 267 248 244 243 242 241 239 238 180 177 176 175 174 164 158 155 120 119 99 98 96 95 82 79 78 76 71 70 69 67 66 61 60 59 56 54 52 51 49 48 47 46 44 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119641-1 DESCRIPTION PRODUCT SPEC - 2 2168083-1 Ocean Side Feed Applicator - DRAWING NO 2151825 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV C D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - D D FEED TYPE 44 PNEUMATIC 2 244 243 177 A 242 238 2 3 REF 8 59 8.1 82 1 20 C 34 REF 1 120 SEE DETAIL A C 70 69 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) TERMINAL SUPPORT LOCATION 2 3 2 176 56 2 1 4 28 5 174 41 52 21 DETAIL A 20 19 2 33 24 175 30 16.6 180 REF 9 78 B RAM AND HOLDDOWN SET-UP 1 B 12 76 241 95 13 96 1 61 30mm STROKE 30 ITEM 30 LOCATED AT REAR HOLES 29 CAM POSITION 0.5 67 2 A 79 REF 0.05 66 3 180 164 44 43.90 51 7 0.5 29 11 27 REF REF 119 267 25 26 23 158 155 46 98 99 34 8 1 60 54 10 1 18.54 248 0.50 FEED TRACK POSITION GUIDE BY WIRE BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE AIR FEED AMP 4805 REV 31MAR2000 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 19DEC2012 CHK 28DEC2012 APVD 28DEC2012 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151825 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV C 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2151825 -2 C FINE CRIMP HEIGHT ADJUST PNEUMATIC 7- 2151825 -7 A CRIMP TOOLING KIT - 1 - 1 - 3 1 - D 1 - - - WIRE INSUL 1 - 3 1 - 1 - SIZE APPLICATOR INSTRUCTIONS 408-35042 1 - F O 7.11 mm [.280] 1 - TYPE 5.33 mm [.210] 1 - REF - 1 - 1 - 1 - 1 - LEAR TERMINAL TERMINAL DATA: LEAR CRIMP SPECIFICATION WIRE STRIP LENGTH C TERMINAL APPLICATION SPECIFICATION - TERMINALS APPLIED TE TERMINAL 2113306-1 28490306189 C1__DWG_PN_1_1 - - - 1 - 1 - 1 - 1 - 1 - 1 - 6 LEAR TERMINAL C1__DWG_PN_1_0 - 1 - 4.10-6.00 mm [.161-.236 IN] N.106.867 Rev 8 - - INSULATION DIAMETER RANGE 8.00-8.02 mm [.315-.316 IN] 2 - FLAT CONTACT 8x0.8/9.5x1.2 TERMINAL NAME: 2 C1__DWG_PN_2_0 TE TERMINAL LEAR TERMINAL C1__DWG_PN_3_0 1 - C1__DWG_PN_4_0 2 - C1__DWG_PN_2_1 1 - 1 - 1 - WIRE SIZE 10.00mm2 6.00mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 3.30+0.10/-0.05 [.130+.004/-.002] 3.00+/-0.05 [.118+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 5.0 7.7 1 - 4 1 W1__FA_SETTING_1 1 - 5 2 - 2 - W1__FA_SETTING_2 1 - 1 - 1 - 1 - 1 - - - 1 - 1 1 B 2 3 4 5 6 7 2 - 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 - 2 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. 1 - 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 - 1 - 1 - 2 - 7 APPLICATOIN NOT RECOMMENDED IN PRESS WITH INSUFFICENT TONNAGE. 1 - 1 1 - TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 1 - 1 - 1 1 1 1 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 - 1 RELOCATE ITEM 19 TO BACK OF APLICATOR. 1 - - - 1 1 1 1 1 1 1 - 1 1 LTR THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DESCRIPTION DWN 19DEC2012 CHK 28DEC2012 APVD 28DEC2012 R.O.WILSON K.J.STAKEM T.L.ELBIN 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-2 1 2-1752354-7 1 6-993111-6 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 1 COUNTER_994970 1 1-22281-8 1 2168083-6 1 2119641-2 1 2168083-8 2 2168083-9 1 2119653-2 1 1-1803583-8_MOD 1 1803516-2 1 455888-6 1 318563-1 1 2844908 1 2844907 1 2-690438-2 2 2168083-1 1 1803078-1 2 2079383-4 1 1803096 1 1633782-3 1 1803607_3 1 1-2119791-2 1 2119943-1 1 2119740-1 2 2168078-1 2 2-18032-5 1 5-18022-5 1 1-1338683-1 1 1-5018030-0 1 1901681-2 3 18023-9 1 2119652 1 1803602-2 1 4-1752356-5 2 1-2079383-3 2 3-2844962-7 1 2844938-9 1 1-455888-0 2 SIMP_22281-8 1 356835-1 1 240792-1 1 1320928-6 1 980371-4 1 2168083-2 2 1-18028-2 1 1803013-1 1 2119806 1 SIMP_4-22280-7 1 1-356885-3 1 1-2119805-0 1 1-318059-0 1 2-1333229-3 .. 1 ITEM_7 .. 1 ITEM_6 1 1803080-1 1 238011-1 1 1-1803017-4 1 1-455888-4 1 456430-2 267 244 243 242 241 239 238 180 177 176 175 174 164 158 155 151 144 143 142 141 140 120 119 99 98 96 95 82 79 78 76 71 70 69 67 66 61 59 56 52 51 49 48 41 34 33 30 29 28 27 26 25 24 23 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 NAME A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119082-6 TE Connectivity SIZE - - 2 2168083-1 DESCRIPTION - WEIGHT APVD - SCR, SKT HD CAP, RoHS, M3 X 8.0 CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 14.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC SPRING, COMPRESSION SCR, SKT HD CAP, RoHS, M5 X 65 FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC SPACER, CRIMPER GUARD, FRONT CHIP SCREW, LOCKING POST, LOCKING FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SPACER, PRECISION SCR, BHSC, RoHS (M4 X 8) EXTENSION PLATE FENCE DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SET, FLT PNT, M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 FEED PAWL NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 40) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 25) SPACER, CYLINDRICAL, STRIP GUIDE PLATE, STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL STRIP GUIDE SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F SPACER, CRIMPER CRIMPER, WIRE APPLICATION SPEC - DWN - PRODUCT SPEC - DATE SEE SHEET 1 PART NO -77 -22 PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 - - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING. REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. AMP 4805 REV 31MAR2000 2 - RECOMMENDED SPARE PARTS A P 2168083-1 2119082-6 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-2 2-1752354-7 6-993111-6 8-22280-7 1752353-2 1901680-2 994970-2 1-22281-8 2168083-6 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-8 1803516-2 455888-6 318563-1 2844908-1 2844907-1 2-690438-2 2168083-1 1803078-1 2079383-4 1803096-1 1633782-3 1803607-3 1-2119791-2 2119943-1 2119740-1 2168078-1 2-18032-5 5-18022-5 1-1338683-1 1-5018030-0 1901681-2 18023-9 2119652-1 1803602-2 4-1752356-5 1-2079383-3 3-2844962-7 2844938-9 1-455888-0 22281-8 356835-1 240792-1 1320928-6 980371-4 2168083-2 1-18028-2 1803013-1 2119806-1 4-22280-7 1-356885-3 1-2119805-0 1-318059-0 2-1333229-3 1803080-1 238011-1 1-1803017-4 1-455888-4 456430-2 2 - CRIMP 66 - - APPLICATOR DATA REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 Ocean Side Feed Applicator - DRAWING NO 2151825 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - D DATE DWN APVD - - - D 140 244 FEED TYPE 243 PNEUMATIC 242 2 3 238 A 8 177 REF 8.1 0.5 34 REF 59 20 TERMINAL SUPPORT LOCATION 82 1 C SEE DETAIL A 2 56 2 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 120 176 70 69 2 174 52 2 21 DETAIL A C 1 20 19 7 1 4 28 5 41 175 34.87 0.05 2 0.5 67 164 A 79 REF 16.6 66 3 180 30 140 51 33 24 3 180 REF RAM AND HOLDDOWN SET-UP 78 B 9 76 CAM POSITION 30mm STROKE B 95 12 96 241 29 13 1 ITEM 30 LOCATED AT REAR HOLES 30 REF 1 29 61 REF 27 267 151 25 26 23 158 141 155 98 99 34 8 1 144 143 10 1 119 18.5 11 FEED TRACK POSITION GUIDE BY WIRE BARREL A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 AIR FEED PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 0.5 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 19DEC2012 CHK 28DEC2012 APVD 28DEC2012 R.O.WILSON K.J.STAKEM T.L.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 A Ocean Side Feed Applicator - DRAWING NO 2151825 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV C