8-2266051-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 5 4 3 2 20 REVISION DESCRIPTION FEED TYPE 2266051 -1 A FINE CRIMP HEIGHT ADJUST MECHANICAL 2266051 -5 D FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST 2266051 -6 A NON-CRIMP HEIGHT ADJUST 2266051 -7 A FINE CRIMP HEIGHT ADJUST 7- 2266051 -7 A 4 SUPERSEDED BY 5-2151121-1 - CRIMP TOOLING KIT - SUPERSEDED BY 5-2151121-2 - 4 SERVO LATCH PLATE 12 NONE - OBSOLETE - OBSOLETE 6 OBSOLETE - - - CRIMP WIRE INSUL APPLICATOR DATA SIZE - TYPE - F O 2.29 mm [.090] 3.68 mm [.145] APPLICATOR INSTRUCTIONS 408-10389 - - - TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 4.00-4.50 mm [.157-.177 IN] TERMINAL APPLICATION SPECIFICATION C n 114-5082 - - TE CRIMP SPECIFICATION TAB CONTACT 070 TYPE TERMINAL NAME: INSULATION DIAMETER RANGE 2.00-2.70 mm [.079-.106 IN] - - - - - 13 - TERMINALS APPLIED TE TERMINAL 171661-1 171661-3 TE TERMINAL C1__DWG_PN_1_0 171661-5 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 C1__DWG_PN_1_2 TE SEAL 172888-1 172888-2 C1__DWG_PN_3_2 1-172888-3 1.25mm2 0.85mm2 0.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.52+/-0.05 [.060+/-.002] 1.37+/-0.05 [.054+/-.002] 1.24+/-0.05 [.049+/-.002] C1__DWG_PN_4_1 CRIMP HEIGHT REFERENCE SETTING 5.7 W1__DWG_CRIMP_HT_1 7.3 W1__DWG_CRIMP_HT_2 8.7 W1__DWG_CRIMP_HT_3 14 C1__DWG_PN_4_3 347874-1 1-900325-9 C1__DWG_PN_3_4 - C1__DWG_PN_4_2 176886-5 C1__DWG_PN_3_3 6 C1__DWG_PN_4_0 176886-2 176886-4 C1__DWG_PN_3_1 9-172888-2 WIRE SIZE TE SEAL C1__DWG_PN_3_0 C1__DWG_PN_4_4 - C1__DWG_PN_4_5 16 9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 W1__FA_SETTING_4 - B 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY 6 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 7 - -4 -4 -5 -6 - 8 9 10 11 A 12 13 14 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62 & 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37, 62 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 242. & 252. MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 1 1 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT THIS APPLICATOR APPLIES TERMINAL WITH A SEAL. APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. AMP 4805 REV 31MAR2000 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 - 2266051 2266051 2266051 2266051 1 1 - 15 16 66 P LTR A1 PNEUMATIC SERVO LATCH PLATE REVISIONS A - A 1 DIST A 2119599-1 PART NUMBER 2266051 -2 LOC SET UP GAUGE ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 6 - THE APPLICATOR IS SPECIFIC FOR USE IN A STRIPPER SEAL CUT TO LENGTH AT ASSEMBLY. - 1 -77 -7 1 - -6 1 -5 1 -2 1 2119957-2 8-21084-0 -1 PART NO - APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. DESCRIPTION 1 2119957-2 1 8-21084-0_GATD 260 252 1 1 1 1 ITEM NO 1 1 1 1 1 1 1 REF - 1 1 1 1 2 1 3 1 1 4 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - 1 - - 1 - - 1 1 - 2 1 1 1 REF REF REF REF - - - 1 - - - 1 1 1 1 1 1 -6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 - 4 2 1 1 1 4 2 1 1 1 4 1 1 1 - 2 1 1 1 4 3 1 - - 1 3 1 1 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - - 1 1 2 1 - 1 - - 1 REF REF 1 - - 1 1 - - 1 1 - 1 REF REF 1 - 1 1 1 -5 -2 mm MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - TE ECR-18-013073 19AUG2018 TB TE PART NO - PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE PNT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP, RoHS, M4 X 16 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 24SEP2013 CHK 24SEP2013 APVD 24SEP2013 X.ZHAO T.ELBIN L.ZHANG NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 2119082-7 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1_OLD 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-6 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 985575-3 1 1338685-1 4 2168400-1 2 2168083-8 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2119653 1 2-2119656-1 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 1-2119644-2 1 2119085_PRE_REV_K 1 2119092-1 1 1752356-2 2 2079383-5 1 2161328 1 1-1320908-0 1 2119959-1 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1333205-4 1 4-240641-1 1 2119781-1 1 4-238011-0 1 1803018-6 1 455888-1 1 4-456406-7 250 249 248 247 246 245 244 243 242 241 240 239 238 213 198 172 166 164 163 137 136 135 133 119 117 82 71 67 66 63 62 60 59 57 56 54 53 52 51 50 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079988_GATD TE Connectivity APPLICATION SPEC - 1 2119640-1 DESCRIPTION PRODUCT SPEC - APVD LG -1 - DWN 25OCT2013 1 - - - 1 - - 1 - 1 1 1 1 - - - 1 1 - - - 1 1 2 - 1 1 1 2 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 1 1 - DATE RELEASED 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 2119082-7 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-6 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 985575-3 1338685-1 2168400-1 2168083-8 5018030-1 811242-5 690753-2 18023-9 2119652-1 2119653-1 2-2119656-1 2119370-1 2079383-7 2119645-1 2119957-1 1-2119644-2 2119085-1 2119092-1 1752356-2 2079383-5 2161328-1 1-1320908-0 2119959-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1333205-4 4-240641-1 2119781-1 4-238011-0 1803018-6 455888-1 4-456406-7 - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 4 of 4) - -77 -7 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 - - DESCRIPTION Ocean Side Feed Applicator - DRAWING NO 2266051 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE MECHANICAL D 59 38 56 39 A 247 246 260 44 7 252 245 7 16 53 63 35 166 82 1 57 REF 2 SHEAR DEPRESSOR DETAIL 2 6 3 52 C 1 4 56 240 51 133 4 TERMINAL SUPPORT LOCATION 28 5 41 135 198 66 2 164 A 67 11 57 213 33 A 24 SERVO FEEDER NOT INCLUDED B 3.96 0.05 [ 0.156 0.001 ] 34 REF 2 SERVO LATCH PLATE REF 1 137 172 2 8 136 C 0.89 [ 0.035 ] 8 7 59 2 243 242 50 D 2 244 238 163 - REF 5 2 249 - - 40 239 PNEUMATIC APVD 62 6 250 DWN 37 6 A DATE 117 REF 10 14 19 B 30 20 9 29 21 12 1 241 13 1 ITEM 30 LOCATED AT FRONT HOLES 11 30 REF 29 REF CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 47 46 32 34 54 8 1 60 54 10 1 119 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24SEP2013 CHK 24SEP2013 APVD 24SEP2013 X.ZHAO T.ELBIN L.ZHANG TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266051 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 6 5 4 3 2 20 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2266051 -1 A FINE CRIMP HEIGHT ADJUST MECHANICAL D A FINE CRIMP HEIGHT ADJUST OBSOLETE PNEUMATIC 2- 2266051 -5 A FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 2- 2266051 -7 A FINE CRIMP HEIGHT ADJUST NONE 7- 2266051 -7 A CRIMP TOOLING KIT - OBSOLETE - 4 - OBSOLETE - 6 OBSOLETE - - - CRIMP WIRE INSUL APPLICATOR DATA SIZE - TYPE - F O 2.29 mm [.090] 3.68 mm [.145] APPLICATOR INSTRUCTIONS 408-10389 - - TE TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 4.00-4.50 mm [.157-.177 IN] C TERMINAL APPLICATION SPECIFICATION n 114-5082 - - TE CRIMP SPECIFICATION TAB CONTACT 070 TYPE TERMINAL NAME: INSULATION DIAMETER RANGE 2.00-2.70 mm [.079-.106 IN] - - - - - - 12 - TERMINALS APPLIED TE TERMINAL 171661-1 171661-3 TE TERMINAL C1__DWG_PN_1_0 171661-5 C1__DWG_PN_1_1 TE SEAL C1__DWG_PN_2_0 C1__DWG_PN_3_0 172888-1 172888-2 C1__DWG_PN_2_1 C1__DWG_PN_1_2 C1__DWG_PN_3_1 C1__DWG_PN_3_2 1-172888-3 C1__DWG_PN_3_3 9-172888-2 WIRE SIZE 1.25mm2 0.85mm2 0.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.52+/-0.05 [.060+/-.002] 1.37+/-0.05 [.054+/-.002] 1.24+/-0.05 [.049+/-.002] C1__DWG_PN_3_4 TE SEAL 176886-2 176886-4 176886-5 347874-1 1-900325-9 - C1__DWG_PN_4_0 - C1__DWG_PN_4_1 - C1__DWG_PN_4_2 - C1__DWG_PN_4_3 - C1__DWG_PN_4_4 - C1__DWG_PN_4_5 CRIMP HEIGHT 9 REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 5.7 7.3 8.7 W1__FA_SETTING_1 6 - 13 - 15 - - W1__FA_SETTING_2 W1__FA_SETTING_3 - W1__FA_SETTING_4 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. B 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2266051 2266051 2266051 2266051 - -4 -4 -5 -6 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 11 A 12 13 14 15 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 & 152. MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - & 242. - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. AMP 4805 REV 31MAR2000 - 1 - 1 1 1 - THIS APPLICATOR APPLIES TERMINAL WITH A SEAL. CUT TO LENGTH AT ASSEMBLY. - TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. THE APPLICATOR IS SPECIFIC FOR USE IN A STRIPPER SEAL TERMINATING UNIT. - 1 SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS.. REVISIONS DIST A 66 P LTR - - 2- 2266051 -2 LOC 1 1 1 1 1 - 1 1 - 1 - - - 1 1 1 1 - 2 1 REF - - - 1 - - 1 - 1 1 1 - - - - - 1 - - - 1 1 2 - 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 REF REF REF - - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 1 1 2 1 1 1 1 2 1 1 1 - 2 3 1 1 - 1 3 - 1 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 - 1 1 1 1 - 1 1 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24SEP2013 CHK 24SEP2013 APVD 24SEP2013 X.ZHAO T.ELBIN L.ZHANG NAME A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2079988_GATD 1 1-22279-3_SIMP 1 2119082-7 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1_OLD 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 2-2119656-2 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-6 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 985575-3 1 1338685-1 2 2168083-8 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 1-2119644-2 1 1752356-2 2 2079383-5 1 2161328 1 1-1320908-0 1 2119959-1 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1333205-4 1 4-240641-1 1 2119781-1 1 4-238011-0 1 1803018-6 1 455888-1 1 4-456406-7 251 250 249 246 244 243 242 241 240 239 238 213 198 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 82 71 67 66 63 62 59 57 56 53 52 51 50 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 SIZE - 1 2119640-1 TE Connectivity - WEIGHT - 1 2119782 DESCRIPTION APPLICATION SPEC - APVD - FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE PNT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 16 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM PRODUCT SPEC - DWN - PART NO -77 -27 -25 -22 -21 DATE SEE SHEET 1 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-7 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 2-2119656-2 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-6 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 985575-3 1338685-1 2168083-8 5018030-1 811242-5 690753-2 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 1-2119644-2 1752356-2 2079383-5 2161328-1 1-1320908-0 2119959-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1333205-4 4-240641-1 2119781-1 4-238011-0 1803018-6 455888-1 4-456406-7 1 1 DESCRIPTION Ocean Side Feed Applicator - DRAWING NO 2266051 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A1 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE - - - 40 145 38 239 246 39 59 7 56 140 152 2 5 REF 2 D 0.89 [ 0.035 ] 2 57 244 7 139 REF SHEAR DEPRESSOR DETAIL 243 PNEUMATIC 250 2 15 53 8 249 A 166 242 2 6 63 238 50 163 3.96 [ 0.156 ] REF 8 7 34 59 82 136 1 137 C 1 56 REF TERMINAL SUPPORT LOCATION 52 172 2 3 51 C 1 4 28 SERVO LATCH PLATE 5 41 240 133 4 135 198 164 66 57 2 33 SERVO FEEDER NOT INCLUDED 213 A 24 19 10 30 13 67 11 A 9 20 117 REF 1 B 12 21 29 241 13 1 11 ITEM 30 LOCATED AT FRONT HOLES 30 CAM POSITIONS 30mm STROKE APVD 62 6 A B DWN 251 MECHANICAL D DATE REF 29 30mm STROKE 30mm STROKE 142 REF 151 141 32 34 143 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 24SEP2013 CHK 24SEP2013 APVD 24SEP2013 X.ZHAO T.ELBIN L.ZHANG TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266051 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A1