8-2266118-4

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION DESCRIPTION FINE CRIMP HEIGHT ADJUST MECHANICAL 5-2266118-1 H SEAL STRIPPER CRIMPER TERMINATING UNIT MECHANICAL 5-2266118-2 H 7-2266118-1 H 7-2266118-2 H 7- 2266118 -7 C FINE CRIMP HEIGHT ADJUST 2 A PNEUMATIC AND CRIMP TOOLING KIT 2.03 mm [.080] APPLICATOR INSTRUCTIONS 408-35042 - PART NUMBER - INSULATION DIAMETER RANGE 7-2266116-8 - 7-2266117-8 3 7-2266118-8 7-2266119-8 DEUTSCH TERMINAL 3.81-5.09 mm [.150-.200 IN] C TERMINAL APPLICATION SPECIFICATION 114-151003 1572032-7 C1__DWG_PN_1_1 1060-20-0177 C1__DWG_PN_1_2 - - - TERMINAL APPLICATION SPECIFICATION 114-151003 - TERMINALS APPLIED C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 1572032-2 C1__DWG_PN_3_0 C1__DWG_PN_3_1 n 3.81-5.09 mm [.150-.200 IN] 1.91-2.29 mm [.075-.090 IN] - DEUTSCH CRIMP SPECIFICATION WIRE STRIP LENGTH 6 DEUTSCH TERMINAL 1060-20-0122 C1__DWG_PN_1_0 - DEUTSCH TERMINAL 1060-20-0144 C1__DWG_PN_4_0 C1__DWG_PN_4_1 C1__DWG_PN_2_2 TE TERMINAL 286680-1 286680-9 286680-6 - STAMPED CONTACT SOCKET SIZE 20 TERMINAL NAME: INSULATION DIAMETER RANGE - TERMINALS APPLIED TE TERMINAL 1572032-1 n DEUTSCH TERMINAL TERMINAL DATA: DEUTSCH CRIMP SPECIFICATION WIRE STRIP LENGTH - - STAMPED CONTACT PIN SIZE 20 TERMINAL NAME: - - 7-2266120-8 TERMINAL DATA: C2__DWG_PN_1_0 C2__DWG_PN_1_1 C2__DWG_PN_1_2 C2__DWG_PN_1_3 3 INSULATION DIAMETER RANGE 1062-20-0122 1062-20-0177 1062-20-0344 - - 1.91-2.29 mm [.075-.090 IN] - - - - - - - 6 DEUTSCH TERMINAL - C2__DWG_PN_2_0 C2__DWG_PN_2_1 C2__DWG_PN_2_2 C2__DWG_PN_2_3 TE TERMINAL 286680-2 286680-5 1-286680-0 C2__DWG_PN_3_0 C2__DWG_PN_3_1 C2__DWG_PN_3_2 C2__DWG_PN_3_3 DEUTSCH TERMINAL 1062-20-0144 1062-20-0322 1062-20-0377 6 C2__DWG_PN_4_0 - C2__DWG_PN_4_1 - C2__DWG_PN_4_2 1 C2__DWG_PN_4_3 - WIRE SIZE 1.50mm2 16 AWG 1.00mm2 18 AWG 0.75mm2 0.60mm2 20 AWG 0.50mm2 22 AWG 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 W1__DWG_WGAUGE_6 W1__DWG_WGAUGE_7 W1__DWG_WGAUGE_8 W1__DWG_WGAUGE_9 W1__DWG_WGAUGE_10 1.47+0.03/-0.05 [.058+.001/-.002] 1.27+0.03/-0.05 [.050+.001/-.002] 1.27+0.03/-0.05 [.050+.001/-.002] 1.24+0.03/-0.05 [.049+.001/-.002] 1.22+0.03/-0.05 [.048+.001/-.002] 1.07+0.03/-0.05 [.042+.001/-.002] 0.99+0.03/-0.05 [.039+.001/-.002] 0.97+0.03/-0.05 [.038+.001/-.002] 0.94+0.03/-0.05 [.037+.001/-.002] 0.94+0.03/-0.05 [.037+.001/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 W1__DWG_CRIMP_HT_5 W1__DWG_CRIMP_HT_6 W1__DWG_CRIMP_HT_7 W1__DWG_CRIMP_HT_8 W1__DWG_CRIMP_HT_9 W1__DWG_CRIMP_HT_10 3.4 5.4 5.4 5.7 5.9 7.4 8.2 8.4 8.7 8.7 - 4 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - W1__FA_SETTING_4 - W1__FA_SETTING_5 - W1__FA_SETTING_6 - W1__FA_SETTING_7 - W1__FA_SETTING_8 - W1__FA_SETTING_9 - W1__FA_SETTING_10 - B 1 2 3 4 5 6 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION & STORAGE OF APPLICATOR. - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 180. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 SEE APPROPRIATE APPLICATOR LOG SHEETS FOR APPLIED TERMINALS, WIRE RANGE AND MEMORY CHIP. TERMINAL LUBRICANT IS RECOMMENDED. 1 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. A 1 1 1 - - - - - - 1 1 1 2 1 1 1 1 1 1 1 - - - REF 1 1 1 1 1 1 1 1 2 1 1 1 4 2 1 1 1 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 2 1 1 1 1 1 1 - REF 1 1 1 1 1 1 1 1 2 1 1 1 4 2 1 2 1 1 1 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 - DWN APVD E1 ECR-19-014989 25SEP2019 FJ TE F ECR-20-010800 30JUL2020 FZ RK G ECR-20-013125 16SEP2020 FZ RK H ECR-22-138026 05MAY2022 FZ GB 1 2 - 2 1 1 1 1 1 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - 1 1 PART NO 1 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH -1 1 -78 -77 -72 -71 -52 -51 -2 DIMENSIONS: 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 - 1 1 1 1 - 1 1 - 1 2 1 1 - 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 - 1 1 - - - 2 - 1 - 1 1 1 - 2 1 2 - 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 - REF REF 1 1 - - REF 1 - - 1 REF - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 2 1 - 1 - 2 1 1803515-3 2-1803583-1 2168083-1 2-1633782-0 2119641-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 4-1722335-3 1-5018030-0 1-1752354-8 993111-1 5-22280-0 1752353-3 1901680-2 994970-2 1-18028-2 2119955-1 2844908-1 2844907-1 455888-7 2266118 1803607-3 2119791-9 2119740-1 2168078-1 2168083-2 5-18022-5 1338685-1 2168083-3 1-2168083-0 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 2-1752356-0 2079383-5 2-2844962-8 2844992-1 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-6 1-1803293-4 2-240641-8 2119757-3 238011-9 1803019-6 455888-8 1803364-2 - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. AMP 4805 REV 31MAR2000 DATE - APPLICATOR CONVERSION KITS 5 F O 1.75 mm [.069] DESCRIPTION D - WIRE INSUL LTR - APPLICATOR CONVERSION KIT TYPE P PNEUMATIC CRIMP TOOLING KIT SIZE 66 MECHANICAL - CRIMP REVISIONS DIST PNEUMATIC MECHANICAL AND CRIMP TOOLING KIT APPLICATOR DATA 1 PNEUMATIC SEAL STRIPPER CRIMPER TERMINATING UNIT C 3 ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER FEED TYPE H 7-2266118-8 4 LOC 2266118 -1 H 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2266118 -2 D 6 - RAM ASSEMBLY, SF ATLANTIC APPLICATOR BASIC ASSEMBLY, SF SCR, SKT HD CAP, RoHS, M3 X 8.0 FENCE FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE STRIPPER, SIDE FEED NUT, HEX, REG, RoHS, M3.5 STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN COUNTER, MAGNETIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER PRINT, APPLICATOR LOG SHEET DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 10 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEUTSCH STYLE SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 16-Oct-13 CHK 16-Oct-13 APVD 16-Oct-13 R.KNEPPER G.BAILEY M.CLIFFORD NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2-1633782-0 1 2119641-1 1 2119082-9 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 4-1722335-3 1 1-5018030-0 1 1-1752354-8 1 993111-1 1 SIMP_5-22280-0 1 1752353-3 1 1901680-2 1 COUNTER_994970 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-7 1 2266118_LOGSHEET 1 1803607_3 1 2119791-9 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 1338685-1 4 2168083-3 2 1-2168083-0 1 1803382-6 3 18023-9 1 2119652 1 2119653-1 1 1803583-9 1 1803515-1 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-8 1 2844992-1 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-6 1 1-1803293-4 1 2-240641-8 .. 1 ITEM_6 1 2119757-3 1 238011-9 1 1803019-6 1 455888-8 1 1803364-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 2 2168083-1 293 292 269 267 248 244 243 242 241 239 238 182 181 180 177 176 175 174 164 119 113 99 98 82 72 71 70 67 66 60 59 56 54 53 50 49 48 47 46 44 41 34 33 30 29 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2-1803583-1 DESCRIPTION PRODUCT SPEC - 1 1803515-3 Ocean Side Feed Applicator - DRAWING NO 2266118 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV H C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 56 44 PNEUMATIC 293 2 244 243 A 53 238 242 2 50 3 7 8 59 C 82 1 1 2 C 3 177 1 TERMINAL SUPPORT LOCATION 4 2 176 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 70 5 41 44 174 181 2 44.60 175 182 DETAIL A 3 164 33 B 180 2 0.05 67 16.6 B 20 267 21 29 9 269 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 CAM POSITIONS 13 30 REF 29 REF 1 11 30mm STROKE 30mm STROKE 119 113 6 292 46 98 99 34 54 8 1 60 54 10 1 267 REF 5.5 47 248 48 0.5 RAM AND HOLDDOWN SET-UP 19 30 30mm STROKE 293 REF 66 A 24 REF 34 REF SEE DETAIL A 56 0.0 0.5 FEED TRACK POSITION GUIDE BY WIRE BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16-Oct-13 CHK 16-Oct-13 APVD 16-Oct-13 R.KNEPPER G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266118 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV H 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2266118 -1 H FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2266118 -7 C CRIMP TOOLING KIT - H 7-2266118-8 FINE CRIMP HEIGHT ADJUST C 3 2 LOC PART NUMBER 2- 2266118 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC APPLICATOR CONVERSION KIT - D D CRIMP WIRE INSUL APPLICATOR DATA APPLICATOR CONVERSION KITS 5 SIZE PART NUMBER TYPE F O 1.75 mm [.069] 2.03 mm [.080] APPLICATOR INSTRUCTIONS 408-35042 INSULATION DIAMETER RANGE 7-2266116-8 7-2266117-8 7-2266118-8 7-2266119-8 7-2266120-8 - DEUTSCH TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 3.81-5.09 mm [.150-.200 IN] C TERMINAL APPLICATION SPECIFICATION 1572032-1 1572032-7 WIRE SIZE 1.50mm2 16 AWG 1.00mm2 18 AWG 0.75mm2 0.60mm2 20 AWG 0.50mm2 22 AWG 0.35mm2 114-151003 1060-20-0122 1060-20-0177 C1__DWG_PN_1_1 C1__DWG_PN_1_2 - - - W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 W1__DWG_WGAUGE_6 W1__DWG_WGAUGE_7 W1__DWG_WGAUGE_8 W1__DWG_WGAUGE_9 W1__DWG_WGAUGE_10 114-151003 - TERMINALS APPLIED C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 1572032-2 C1__DWG_PN_3_0 C1__DWG_PN_3_1 DEUTSCH TERMINAL 1060-20-0144 TE TERMINAL 286680-1 C1__DWG_PN_4_0 C1__DWG_PN_4_1 286680-9 C1__DWG_PN_2_2 286680-6 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 TERMINAL APPLICATION SPECIFICATION 6 DEUTSCH TERMINAL C1__DWG_PN_1_0 - 1.47+0.03/-0.05 [.058+.001/-.002] 1.27+0.03/-0.05 [.050+.001/-.002] 1.27+0.03/-0.05 [.050+.001/-.002] 1.24+0.03/-0.05 [.049+.001/-.002] 1.22+0.03/-0.05 [.048+.001/-.002] 1.07+0.03/-0.05 [.042+.001/-.002] 0.99+0.03/-0.05 [.039+.001/-.002] 0.97+0.03/-0.05 [.038+.001/-.002] 0.94+0.03/-0.05 [.037+.001/-.002] 0.94+0.03/-0.05 [.037+.001/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 W1__DWG_CRIMP_HT_5 W1__DWG_CRIMP_HT_6 W1__DWG_CRIMP_HT_7 W1__DWG_CRIMP_HT_8 W1__DWG_CRIMP_HT_9 W1__DWG_CRIMP_HT_10 3.4 5.4 5.4 5.7 5.9 7.4 8.2 8.4 8.7 8.7 n 3.81-5.09 mm [.150-.200 IN] 1.91-2.29 mm [.075-.090 IN] - TERMINALS APPLIED TE TERMINAL n DEUTSCH CRIMP SPECIFICATION WIRE STRIP LENGTH INSULATION DIAMETER RANGE - C2__DWG_PN_1_0 C2__DWG_PN_1_1 C2__DWG_PN_1_2 C2__DWG_PN_1_3 INSULATION DIAMETER RANGE 1.91-2.29 mm [.075-.090 IN] - - - - 1062-20-0177 1062-20-0344 - C2__DWG_PN_2_0 C2__DWG_PN_2_1 C2__DWG_PN_2_2 C2__DWG_PN_2_3 TE TERMINAL 286680-2 286680-5 1-286680-0 C2__DWG_PN_3_0 C2__DWG_PN_3_1 C2__DWG_PN_3_2 C2__DWG_PN_3_3 DEUTSCH TERMINAL 1062-20-0144 1062-20-0322 1062-20-0377 6 4 W1__FA_SETTING_4 1 2 3 4 5 6 REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION & STORAGE OF APPLICATOR. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 SEE APPROPRIATE APPLICATOR LOG SHEETS FOR APPLIED TERMINALS, WIRE RANGE AND MEMORY CHIP. 1 TERMINAL LUBRICANT IS RECOMMENDED. 1 7. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. A AMP 4805 REV 31MAR2000 1 1 - - - - 1 - 1 1 1 - 1 1 1 - 1 1 1 1 1 1 DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - SCR, SKT HD CAP, RoHS, M3 X 8.0 FENCE CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 ASSY, LUBRICATOR, SIDE FEED SCREW, LOCKING POST, LOCKING SPACER, CRIMPER PRINT, APPLICATOR LOG SHEET DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 10 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEUTSCH STYLE SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -78 -77 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 1 1 1 - - 1 1 - - 1 1 1 - 1 1 - - 1 1 - 1 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 1 1 - - 2 1 - - 2 2 - - 1 2 - - 1 1 - - 1 1 - - 2 - - - RECOMMENDED SPARE PARTS 1 1 - - 2 1 - - B 1 2 - - 1 1 - - 2 1 - - 1 2 - - W1__FA_SETTING_10 1 1 - - W1__FA_SETTING_9 1 1 - - W1__FA_SETTING_8 - 1 - - W1__FA_SETTING_7 1 - - - W1__FA_SETTING_6 1 1 - - W1__FA_SETTING_5 1 1 - - W1__FA_SETTING_3 1 1 - 1 W1__FA_SETTING_2 1 1 - - W1__FA_SETTING_1 1 1 - - 1 1 - - 1 1 - - 4 - - - 1 4 - - C2__DWG_PN_4_3 - 1 - - C2__DWG_PN_4_2 1 - - C2__DWG_PN_4_1 - REF REF - - C2__DWG_PN_4_0 1 1 - - 1 - - - 1 1 - - 1 1 - - 1 1 - - 6 DEUTSCH TERMINAL 1062-20-0122 - 1 1 - 2168083-1 2-1633782-0 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2119955-1 2844908-1 2844907-1 455888-7 2266118 1803607-3 2119791-9 2119740-1 2168078-1 5-18022-5 1338685-1 1-2168083-0 1803382-6 18023-9 2119652-1 1803602-1 2-1752356-0 2079383-5 2-2844962-8 2844992-1 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-6 1-1803293-4 2-240641-8 2119757-3 238011-9 1803019-6 455888-8 1803364-2 2 1 - 3 2 - - STAMPED CONTACT SOCKET SIZE 20 TERMINAL NAME: STAMPED CONTACT PIN SIZE 20 TERMINAL NAME: DEUTSCH TERMINAL TERMINAL DATA: DEUTSCH CRIMP SPECIFICATION - DWN 16-Oct-13 CHK 16-Oct-13 APVD 16-Oct-13 R.KNEPPER G.BAILEY M.CLIFFORD NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2119955-1 1 2844908 1 2844907 1 455888-7 1 2266118_LOGSHEET 1 1803607_3 1 2119791-9 1 2119740-1 2 2168078-1 1 5-18022-5 1 1338685-1 2 1-2168083-0 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-8 1 2844992-1 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-6 1 1-1803293-4 1 2-240641-8 .. 1 ITEM_6 1 2119757-3 1 238011-9 1 1803019-6 1 455888-8 1 1803364-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119082-9 269 267 244 243 242 241 239 238 164 151 144 143 142 141 140 119 113 99 98 82 72 71 70 67 66 59 56 53 50 49 48 41 34 33 30 29 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2-1633782-0 DESCRIPTION PRODUCT SPEC - 2 2168083-1 Ocean Side Feed Applicator - DRAWING NO 2266118 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV H C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 140 59 D 2 244 56 PNEUMATIC 243 242 A 3 0.0 238 53 REF 8 50 34 7 59 REF TERMINAL SUPPORT LOCATION 82 1 C SEE DETAIL A 2 C 1 2 56 3 1 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 4 70 5 140 41 35.57 REF 0.05 66 DETAIL A 164 2 33 RAM SET-UP 24 B 67 19 A 20 30 B 9 21 267 1 12 29 241 269 13 CAM POSITIONS 30mm STROKE 1 30 REF REF 29 30mm STROKE 30mm STROKE 142 ITEM 30 LOCATED AT FRONT HOLES 267 REF 151 5.5 113 48 6 141 98 99 34 143 8 1 144 143 10 1 119 11 0.5 FEED TRACK POSITION GUIDE BY WIRE BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 16-Oct-13 CHK 16-Oct-13 APVD 16-Oct-13 R.KNEPPER G.BAILEY M.CLIFFORD TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266118 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV H