8-2266146-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 REVISION DESCRIPTION APPLICATOR STYLE CONVERSION CHART FEED TYPE CONVERT TO - - B FINE CRIMP HEIGHT ADJUST PNEUMATIC SERVO LATCH PLATE 2119951-1 2266146 -5 B FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE - - 2266146 -6 B NON-CRIMP HEIGHT ADJUST SERVO LATCH PLATE 11 2266146 -7 B FINE CRIMP HEIGHT ADJUST 7- 2266146 -7 A 4 NONE - CRIMP TOOLING KIT 4 2161326-1 - - - - 8- 2266146 -5 1901094-3 - - - - - 8- 2266146 -4 - - - - 2168400-6 5-18022-5 2119641-1 2119799-1 2063440-2 - - - - - - - - - - - - - - - - - - - - - - - - - - - 7 - - WIRE INSUL SIZE - TYPE F O 3.98 mm [.157] 5.90 mm [.232] APPLICATOR INSTRUCTIONS 408-10389 - 6 - LEAR TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 6.50-7.50 mm [.256-.295 IN] C TERMINAL APPLICATION SPECIFICATION TE TERMINAL 2113405-1 n LEAR-28141 - TERMINALS APPLIED C1__DWG_PN_1_0 C1__DWG_PN_1_1 - TE CRIMP SPECIFICATION TERMINAL TERMINAL NAME: - - INSULATION DIAMETER RANGE - - 4.50-6.00 mm [.177-.236 IN] REVISION 3 - - - - - - 10 12 LEAR TERMINAL 28141.201.178 C1__DWG_PN_2_0 TE TERMINAL - 12 LEAR TERMINAL C1__DWG_PN_3_0 - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE (4)1.00 (2)0.75 + 1.00 + 1.50 (3)0.75 + 1.50 (3)1.00 (2)0.75 + 1.00 B CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 3.05+/-0.05 [.120+/-.002] 3.05+/-0.05 [.120+/-.002] 3.00+/-0.05 [.118+/-.002] 2.95+/-0.05 [.116+/-.002] 2.80+/-0.05 [.110+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 W1__DWG_CRIMP_HT_5 4.7 4.7 5.6 6.3 8.0 - 6 9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - W1__FA_SETTING_4 - W1__FA_SETTING_5 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. - 6 - 7 - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- - 2266146 -4 2266146 -5 2266146 -6 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 11 A 12 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62. APPLY PART NUMBER 2-23419-6 TO THREADS OF ITEM 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37. - 1 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 252. - 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 1 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. WHEN ASSEMBLING A NON CRIMP HEIGHT ADJUST APPLICATOR (-6) USE SHIMS FROM ITEM 260 TO ACHIEVE A NOMINAL SHIM HEIGHT OF 1 1 1 1 2.75 . - 1 1 - 1 1 - 1 - - DATE DWN APVD A RELEASED 26FEB2014 KS TE B ECR-17-010458 19JUL2017 TB TE DIMENSIONS: ATLANTIC VERSION mm & 4 of 4) MATERIAL - 1 -2 PART NO - - 1 REF - 1 - 1 1 1 1 - - - 1 - 1 2 - - 1 1 2 - 1 1 1 - - 1 1 1 1 - 1 1 1 1 1 1 1 1 - - 1 - - 1 1 - - 1 1 - - - 1 2 1 1 REF REF REF - - - - - - - - - 1 1 - 1 REF REF - 1 1 1 1 - - 1 1 REF REF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 - 2 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 - 1 2 - 1 1 1 2 - 1 1 - 2 - 1 - - 2 3 1 - - 1 3 1 - 2 1 - 1 1 2 - 3 1 - 2 1 1 1 - 2 1 1 1 1 - 1 1 1 1 1 -6 -5 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 DESCRIPTION 2119957-2 1803078-1 8-21084-0 2119640-1 1803259-1 2119641-1 2119798-1 1-22279-3 2161314-1 2119082-9 2079764-1 2119083-1 2168400-6 2063440-2 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 2119955-1 1-455888-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 1338685-1 2168400-1 18023-9 2119656-9 2161311-1 1-2079383-5 2119645-1 2119957-1 2119644-5 2119085-1 2119092-1 2079383-5 2161328-1 1320908-7 2119959-4 1-455888-0 240792-2 1320928-2 2168083-2 1-18028-2 2119533-1 3-22280-3 1-356885-3 2119805-1 6-454276-5 6-1633927-7 1-2119757-3 4-238011-9 3-1803019-9 1-455888-7 1-1633588-3 - 1 - -77 -7 TERMINAL LUBRICANT IS RECOMMENDED. AMP 4805 REV 31MAR2000 LTR - - CRIMP P - - APPLICATOR DATA 66 - 1338685-1 - A (QUANTITY 2) 2119950-1 - REVISIONS DIST - PNEUMATIC FEED - 1 PART NUMBERS REQUIRED 2266146 -2 SMART APPLICATOR LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER D 6 TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 02NOV2013 CHK 02NOV2013 APVD 02NOV2013 K. STAKEM T. ELBIN G. BAILEY - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 8-21084-0_GATD 1 2119640-1 1 1803259-1 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 1 2161314 1 2119082-9 1 2079764 1 2119083 2 2168400-6 1 2063440-2 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 2119955-1 1 1-455888-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 1338685-1 2 2168400-1 3 18023-9 1 2119656-9 1 2161311 1 1-2079383-5 1 2119645 1 2119957-1 1 2119644-5 1 2119085_PRE_REV_K 1 2119092-1 2 2079383-5 1 2161328 1 1320908-7 1 2119959-4 1 1-455888-0 1 240792-2 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 SIMP_3-22280-3 1 1-356885-3 1 2119805-1 1 6-454276-5 1 6-1633927-7 .. 1 ITEM_7 .. 1 ITEM_6 1 1-2119757-3 1 4-238011-9 1 3-1803019-9 1 1-455888-7 1 1-1633588-3 260 259 252 250 249 248 247 246 245 244 243 242 240 238 213 198 172 166 164 163 137 136 135 133 119 117 113 82 71 67 66 63 62 60 59 56 54 49 46 44 41 40 39 38 37 35 33 32 30 29 28 25 24 21 20 19 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 1803078-1 TE Connectivity APPLICATION SPEC - 1 2119957-2 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APPLICATOR SHIM PACK SPACER, PRECISION O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, FLANGED FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, STEPPED, ATLANTIC, SF, NON-ADJ CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 16 AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF ASSY, LUBRICATOR, SIDE FEED SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP M4 X 6.0 APPLICATOR BASIC ASSEMBLY, SF RAM, STEPPED, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 40) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER DRAG, TERMINAL STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE Ocean Side Feed Applicator - DRAWING NO 2266146 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV B D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - 6 6 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 37 62 40 D 247 38 FEED TYPE 246 39 PNEUMATIC 250 2 260 44 7 252 245 35 244 7 249 2 2 2 2 243 63 A D 166 238 8 242 2 6 163 259 59 82 1 136 1 137 C C 2 172 3 1 56 4 SERVO LATCH PLATE 240 133 4 2 164 67 213 33 A 24 117 REF 41 66 A B 5 135 198 SERVO FEEDER NOT INCLUDED 28 19 30 20 29 21 B 9 1 ITEM 30 LOCATED AT FRONT HOLES 12 30 REF 29 REF CAM POSITION 11 30mm STROKE 119 113 12 25 46 32 8 1 60 54 10 1 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE AIR FEED AMP 4805 REV 31MAR2000 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 02NOV2013 CHK 02NOV2013 APVD 02NOV2013 K. STAKEM T. ELBIN G. BAILEY TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266146 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER REVISION 2- 2266146 -2 B 2- 2266146 -5 CONVERT TO PNEUMATIC SERVO LATCH PLATE FINE CRIMP HEIGHT ADJUST A APPLICATOR STYLE CONVERSION CHART FEED TYPE FINE CRIMP HEIGHT ADJUST B 7- 2266146 -7 DESCRIPTION FINE CRIMP HEIGHT ADJUST B 2- 2266146 -7 D 6 NONE CRIMP TOOLING KIT - 4 CRIMP WIRE INSUL SIZE - - - - - SERVO LATCH PLATE 2119951-1 - 8- 2266146 -5 1901094-3 - SMART APPLICATOR 2161326-1 - 8- 2266146 -4 - - - - - - - - - - PNEUMATIC FEED 2119950-1 1338685-1 5-18022-5 2119641-2 2119799-1 2063440-2 - - - - - - - - - - - 2168400-6 - - 1 - - 6 LEAR TERMINAL TE CRIMP SPECIFICATION TERMINAL TERMINAL NAME: WIRE STRIP LENGTH 6.50-7.50 mm [.256-.295 IN] C TERMINAL APPLICATION SPECIFICATION LEAR-28141 - TERMINALS APPLIED TE TERMINAL 2113405-1 n C1__DWG_PN_1_0 C1__DWG_PN_1_1 7 INSULATION DIAMETER RANGE 4.50-6.00 mm [.177-.236 IN] REVISION 3 - - - 10 11 LEAR TERMINAL 28141.201.178 C1__DWG_PN_2_0 TE TERMINAL LEAR TERMINAL C1__DWG_PN_3_0 WIRE SIZE (4)1.00 (2)0.75 + 1.00 + 1.50 (3)0.75 + 1.50 (3)1.00 (2)0.75 + 1.00 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 3.05+/-0.05 [.120+/-.002] 3.05+/-0.05 [.120+/-.002] 3.00+/-0.05 [.118+/-.002] 2.95+/-0.05 [.116+/-.002] 2.80+/-0.05 [.110+/-.002] 11 CRIMP HEIGHT 9 REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 W1__DWG_CRIMP_HT_5 4.7 4.7 5.6 6.3 8.0 W1__FA_SETTING_4 6 W1__FA_SETTING_5 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. B 1 2 RECOMMENDED SPARE PARTS GREASE BEARING SURFACES LIGHTLY 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- 2266146 -4 2266146 -5 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 A APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62. APPLY PART NUMBER 2-23419-6 TO THREADS OF ITEM 242. 1 1 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 & 152. 1 MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 10 TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 11 TERMINAL LUBRICANT IS RECOMMENDED. 1 1 1 1 1 1 - 1 - - - - 1 - 1 1 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 2 1 1 - 1 2 1 - 1 1 2 - 1 1 1 - 1 1 1 - 1 1 1 - 1 - 1 - 1 - - - 3 - - - 1 3 - - 2 1 3 - 1 2 1 - 1 - 2 - 1 1 1 - 1 1 1 - - 1 1 - W1__FA_SETTING_3 1 REF 1 - W1__FA_SETTING_2 - 1 - - W1__FA_SETTING_1 - 1 1 - 1 REF - - 1 - - - 1 - - - 1 1 - - 1 1 1 - 2 1 1 - C1__DWG_PN_2_1 1 2 1 - C1__DWG_PN_4_0 1 1 2 - 1 1 1 - 1 - 1 - 1 1 - 7 - 1 - 1 REF REF - - 2 1 REF - - - 1 - - 1 - - 1 1 - - - - - - 1 2 - - 1 1 - - 1 1 1 - 1 1 1 - 1 1 1 - 1 - 1 - 1 - - - TERMINAL DATA: 1 1 1 1 1 1 1 1 1 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - DWN 02NOV2013 CHK 02NOV2013 APVD 02NOV2013 K. STAKEM T. ELBIN G. BAILEY - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119640-1 1 1803259-1 1 1-22279-3_SIMP 1 2119082-9 1 2079764 1 2119083 2 2168400-6 1 2063440-2 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 2 2168400-5 1 1-2119656-0 1 2161312 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 2119955-1 1 1-455888-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 1338685-1 3 18023-9 1 1-2079383-5 1 2119645 1 2119957-1 1 2119644-5 2 2079383-5 1 2161328 1 1320908-7 1 1901086-1 1 2119959-4 1 1-455888-0 1 240792-2 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 SIMP_3-22280-3 1 1-356885-3 1 2119805-1 1 6-454276-5 1 6-1633927-7 .. 1 ITEM_7 .. 1 ITEM_6 1 1-2119757-3 1 4-238011-9 1 3-1803019-9 1 1-455888-7 1 1-1633588-3 259 251 250 249 246 244 243 242 240 238 213 198 172 166 164 163 152 151 145 144 143 141 140 139 137 136 135 133 119 117 113 82 71 67 66 63 62 59 56 49 41 40 39 38 33 32 30 29 29 28 25 24 21 20 19 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119782 TE Connectivity APPLICATION SPEC - 1 1803078-1 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH SPACER, PRECISION FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, FLANGED SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 16 AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 APPLICATOR BASIC ASSEMBLY, SF RAM, STEPPED, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF ASSY, LUBRICATOR, SIDE FEED SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP M4 X 6.0 SCR, BHSC, RoHS (M8 X 40) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE PLATE, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER DRAG, TERMINAL STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PART NO -77 -27 -25 -22 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. AMP 4805 REV 31MAR2000 LTR 1803078-1 2119782-1 2119640-1 1803259-1 1-22279-3 2119082-9 2079764-1 2119083-1 2168400-6 2063440-2 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 1-2119656-0 2161312-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 2119955-1 1-455888-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 1338685-1 18023-9 1-2079383-5 2119645-1 2119957-1 2119644-5 2079383-5 2161328-1 1320908-7 1901086-1 2119959-4 1-455888-0 240792-2 1320928-2 2168083-2 1-18028-2 2119533-1 3-22280-3 1-356885-3 2119805-1 6-454276-5 6-1633927-7 1-2119757-3 4-238011-9 3-1803019-9 1-455888-7 1-1633588-3 1 1 - - TYPE 1 1 - APPLICATOR INSTRUCTIONS 408-10389 P (QUANTITY 2) - 5.90 mm [.232] 66 - F O 3.98 mm [.157] A PART NUMBERS REQUIRED - APPLICATOR DATA REVISIONS DIST - - - LOC 1 Ocean Side Feed Applicator - DRAWING NO 2266146 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - 251 62 6 40 145 38 D 246 39 7 FEED TYPE 140 152 2 D 2 2 244 7 139 243 PNEUMATIC 250 2 8 249 166 2 6 63 238 A 242 163 59 259 82 136 137 C 1 1 2 172 3 56 C 1 4 28 SERVO LATCH PLATE 5 41 240 133 4 135 198 66 A 164 B 67 33 213 A 24 SERVO FEEDER NOT INCLUDED 2 19 20 30 117 REF 9 21 29 B 1 12 ITEM 30 LOCATED AT FRONT HOLES 30 CAM POSITION REF REF 29 30mm STROKE 151 113 11 25 141 32 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 AIR FEED PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 02NOV2013 CHK 02NOV2013 APVD 02NOV2013 K. STAKEM T. ELBIN G. BAILEY TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266146 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B