8-2266261-5

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION REVISION D D FINE CRIMP HEIGHT ADJUST 3-2266261-2 E FINE CRIMP HEIGHT ADJUST 7-2266261-1 D 7-2266261-2 E 7- 2266261 -7 C CRIMP WIRE INSUL C 7 n 3 - - - - TE TERMINAL 2113449-1 2113449-2 2113449-3 2113449-4 2113449-5 DELPHI TERMINAL 15493001 C1__DWG_PN_1_1 13611693 C1__DWG_PN_1_2 13740307 15432210 C1__DWG_PN_1_3 C1__DWG_PN_1_4 35095783 C1__DWG_PN_1_5 C1__DWG_PN_2_1 C1__DWG_PN_2_2 C1__DWG_PN_2_3 TE SEAL 1949130-1 C1__DWG_PN_3_0 C1__DWG_PN_3_1 1949130-2 - DELPHI SEAL 15327918 1949130-3 C1__DWG_PN_4_0 C1__DWG_PN_4_1 15327913 C1__DWG_PN_3_2 C1__DWG_PN_4_2 15339412 C1__DWG_PN_3_3 - - TERMINALS APPLIED C1__DWG_PN_2_0 - - 1.30-2.10 mm [.051-.083 IN] - - - INSULATION DIAMETER RANGE DELPHI CRIMP INFORMATION SHEET PAGE 2 OF 4 - DELPHI CRIMP SPECIFICATION 3.92-4.68 mm [.154-.184 IN] C1__DWG_PN_1_0 - 5 SEAL INSULATION DIAMETER RANGE n 1.20-2.00 - C1__DWG_PN_4_3 n 1.90-2.40 C1__DWG_PN_2_4 6 C1__DWG_PN_2_5 - WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.30+/-0.05 [.051+/-.002] 1.20+/-0.05 [.047+/-.002] 1.10+/-0.05 [.043+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 7.9 8.9 9.9 7 4 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - B 1 2 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 7 A - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 6 - RECOMMENDED SPARE PARTS 3 5 THE INSULATION RANGE LISTED IS FOR THE TERMINAL.REFER TO THE CHART FOR RANGE OF SEALS LISTED ON APPLICATOR DRAWING. APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS 1 1 1 1 - . THIS APPLICATOR IS EQUIPPED WITH THE DOUBLE ACTING FEED WITH SENSORS AND IS APPLICATION SPECIFIC. DOES NOT REQUIRE ITEMS 49 & 248. 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 1 1 - 1 1 1 1 1 1 - 1 1 DESCRIPTION DATE DWN APVD C ECR-17-010580 21JUL2017 FZ KZ D ECR-19-005183 01APR2019 FJ TE E ECR-22-135201 06APR2022 TB RK E1 ECR-22-155261 12OCT2022 FZ JAH 1 1 1 1 1 1 2 1 1 1 1 4 2 1 1 1 1 1 1 2 2 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - 1 1 PART NO 1 1 -2 -32 TOLERANCES UNLESS OTHERWISE SPECIFIED: AIR FEED MODULE FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE DWN 11APR2014 CHK 11APR2014 APVD 11APR2014 X.ZHAO L.ZHANG T.ELBIN - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119082-4 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2844908 1 2844907 1 455888-6 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 985575-3 1 1338683-8 4 2168083-3 2 2168083-3 1 1803382-1 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 1-1752356-3 2 2079383-5 2 3-2844962-2 1 2844992-1 1 455888-3 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 7-1633928-8 1 3-240641-3 .. 1 ITEM_6 1 2119781-5 1 238011-4 1 3-1803019-2 1 1-455888-0 1 1-1803125-6 290 248 244 243 242 241 239 238 164 99 98 82 71 67 66 60 59 57 56 54 53 51 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119641-1 TE Connectivity APPLICATION SPEC - 1 2844950-1 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH -1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: 1 1 1 1 2 1 1 1 1 - 1 1 2 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - - 1 1 1 - 1 2 1 - 1 4 2 1 2 1 4 2 1 1 1 4 2 1 1 1 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 - REF REF 1 1 1 1 REF 1 1 - - 1 1 1 - - 1 1 1 1 1 1 1 1 - 1 1 2844950-1 2119641-1 2119082-4 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2844908-1 2844907-1 455888-6 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 985575-3 1338683-8 2168083-3 2168083-3 1803382-1 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 1-1752356-3 2079383-5 3-2844962-2 2844992-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 7-1633928-8 3-240641-3 2119781-5 238011-4 3-1803019-2 1-455888-0 1-1803125-6 - 1 1 REF REF 1 - - -77 -72 -71 ATLANTIC VERSION AMP 4805 REV 31MAR2000 LTR D F O WIRE STRIP LENGTH TERMINAL APPLICATION SPECIFICATION P - COMPACT TERMINAL SYSTEM 1.5 SEALED TERMINAL NAME: 66 TYPE DELPHI TERMINAL TERMINAL DATA: A PNEUMATIC CRIMP TOOLING KIT APPLICATOR INSTRUCTIONS 408-35042 REVISIONS DIST MECHANICAL PNEUMATIC AND CRIMP TOOLING KIT 3.05 mm [.120] 1 PNEUMATIC DOUBLE ACTING PNEUMATIC WITH SENSORS MECHANICAL AND CRIMP TOOLING KIT 1.85 mm [.073] 2 MECHANICAL FINE CRIMP HEIGHT ADJUST SIZE 3 ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER FEED TYPE 2266261 -1 APPLICATOR DATA 4 LOC DESCRIPTION E 5 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 2266261 -2 6 Ocean Side Feed Applicator - DRAWING NO 2266261 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV E1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 1 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE DATE DWN APVD - - - MECHANICAL 59 A D 239 REF 5 D 56 44 PNEUMATIC 1.5 REF 2 57 REF SHEAR DEPRESSOR DETAIL 244 53 A 243 238 242 2 3 51 59 8 7 82 1 REF 2.0 1 0.5 34 REF SEE DETAIL A C 2 56 C 3 TERMINAL SUPPORT LOCATION 1 4 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 28 5 41 44 44.25 DETAIL A 2 B 33 290 A 67 57 A 24 6 RAM SET-UP 19 B 20 30 59 0.05 66 164 DOUBLE ACTING PNEUMATIC WITH SENSORS 21 9 29 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 56 SEE DETAIL A 13 CAM POSITIONS 47 30 REF 29 REF 1 11 30mm STROKE 30mm STROKE 30mm STROKE 20 46 98 98 34 53 8 1 60 53 10 1 248 48 REF FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 11APR2014 CHK 11APR2014 APVD 11APR2014 X.ZHAO L.ZHANG T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2266261 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV E1 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 4 3 2 20 LOC ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2266261 -1 D FINE CRIMP HEIGHT ADJUST MECHANICAL 2- 2266261 -2 E FINE CRIMP HEIGHT ADJUST PNEUMATIC 4-2266261-2 E FINE CRIMP HEIGHT ADJUST 7- 2266261 -7 C CRIMP TOOLING KIT REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - DOUBLE ACTING PHEUMATIC WITH SENSORS - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE F O 1.85 mm [.073] 3.05 mm [.120] APPLICATOR INSTRUCTIONS 408-35042 - 3 DELPHI CRIMP SPECIFICATION WIRE STRIP LENGTH n 3.92-4.68 mm [.154-.184 IN] TERMINAL APPLICATION SPECIFICATION - 7 - TERMINALS APPLIED TE TERMINAL 2113449-1 2113449-2 2113449-3 2113449-4 2113449-5 DELPHI TERMINAL 15493001 C1__DWG_PN_1_0 C1__DWG_PN_1_1 13611693 13740307 C1__DWG_PN_1_2 C1__DWG_PN_1_3 15432210 C1__DWG_PN_1_4 35095783 C1__DWG_PN_1_5 C1__DWG_PN_2_0 C1__DWG_PN_2_1 C1__DWG_PN_2_2 C1__DWG_PN_2_3 TE SEAL 1949130-1 C1__DWG_PN_3_0 C1__DWG_PN_3_1 1949130-2 1949130-3 C1__DWG_PN_3_2 C1__DWG_PN_3_3 DELPHI SEAL 15327918 5 SEAL INSULATION DIAMETER RANGE n 1.20-2.00 C1__DWG_PN_4_0 C1__DWG_PN_4_1 15327913 15339412 C1__DWG_PN_4_2 C1__DWG_PN_2_5 6 WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 B CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.30+/-0.05 [.051+/-.002] 1.20+/-0.05 [.047+/-.002] 1.10+/-0.05 [.043+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 7.9 8.9 9.9 7 W1__FA_SETTING_1 1 2 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 4 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 6 7 THE INSULATION RANGE LISTED IS FOR THE TERMINAL.REFER TO THE CHART FOR RANGE OF SEALS LISTED ON APPLICATOR DRAWING. APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. 1 1 *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS 1 1 . 1 THIS APPLICATOR IS EQUIPPED WITH THE DOUBLE ACTING FEED WITH SENSORS AND IS APPLICATION SPECIFIC. DOES NOT REQUIRE ITEMS 49 & 151. 1 8. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 1 1 1 1 1 1 1 1 DIMENSIONS: Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: DWN 11APR2014 CHK 11APR2014 APVD 11APR2014 X.ZHAO L.ZHANG T.ELBIN - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2079764_APP 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 2844908 1 2844907 1 455888-6 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 985575-3 1 1338683-8 2 2168083-3 1 1803382-1 3 18023-9 1 2119652 1 1803602-1 1 1-1752356-3 2 2079383-5 2 3-2844962-2 1 2844992-1 1 455888-3 1 1320928-2 1 2168083-2 2 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 7-1633928-8 1 3-240641-3 .. 1 ITEM_6 1 2119781-5 1 238011-4 1 3-1803019-2 1 1-455888-0 1 1-1803125-6 290 244 243 242 241 239 238 164 151 144 143 142 141 140 99 98 82 71 67 66 59 57 56 53 51 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119082-4 TE Connectivity APPLICATION SPEC - 1 2844950-1 DESCRIPTION PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH AIR FEED MODULE CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O SPACER, CRIMPER CRIMPER, WIRE PART NO -22 -21 -42 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION AMP 4805 REV 31MAR2000 1 1 1 -77 - 1 1 1 1 - 1 - 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 - 2 1 1 - 1 2 1 - 1 1 2 - 1 1 1 - 1 1 1 - 2 1 1 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 3 5 A RECOMMENDED SPARE PARTS 2 2 1 - 1 2 2 - 1 1 2 - 1 1 1 - 2 - 1 - 1 1 - - 2 1 - - W1__FA_SETTING_3 1 2 1 - W1__FA_SETTING_2 1 1 2 - 1 1 1 - 2 1 1 - 4 1 2 1 - 1 1 2 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - C1__DWG_PN_2_4 1 1 1 - 4 - 1 - 1 4 - - - 1 4 - C1__DWG_PN_4_3 1 1 - - REF REF - - 1 1 REF - 1 - - - 1 1 - - 1 1 1 - - - - 1 1 1 - 1.30-2.10 mm [.051-.083 IN] DELPHI CRIMP INFORMATION SHEET PAGE 2 OF 4 - 2844950-1 2119082-4 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 2844908-1 2844907-1 455888-6 1803607-3 2119740-1 2168078-1 5-18022-5 985575-3 1338683-8 2168083-3 1803382-1 18023-9 2119652-1 1803602-1 1-1752356-3 2079383-5 3-2844962-2 2844992-1 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 7-1633928-8 3-240641-3 2119781-5 238011-4 3-1803019-2 1-455888-0 1-1803125-6 - 1 1 - INSULATION DIAMETER RANGE - 1 - COMPACT TERMINAL SYSTEM 1.5 SEALED TERMINAL NAME: 1 - DELPHI TERMINAL TERMINAL DATA: C TYPE Ocean Side Feed Applicator - DRAWING NO 2266261 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV E1 C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. FEED TYPE 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - MECHANICAL A 59 D PNEUMATIC 140 56 D 1.5 REF 2 244 57 243 238 A 53 242 2 3 2.0 51 REF SHEAR DEPRESSOR DETAIL 59 REF 8 7 0.5 34 SEE DETAIL A REF 5 239 56 82 1 C REF TERMINAL SUPPORT LOCATION 1 C FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 2 3 1 4 28 5 140 41 35.22 DETAIL A REF 0.05 66 164 DOUBLE ACTING PNEUMATIC WITH SENSORS 57 A 24 A 67 33 290 B 2 59 6 RAM SET-UP 19 20 30 B 9 21 1 12 29 241 SEE DETAIL A 13 56 30mm STROKE 30 1 REF REF 29 CAM POSITIONS 30mm STROKE 30mm STROKE 142 ITEM 30 LOCATED AT FRONT HOLES 151 141 48 98 99 34 143 8 1 144 143 10 1 20 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 11APR2014 CHK 11APR2014 APVD 11APR2014 X.ZHAO L.ZHANG T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2266261 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV E1