82A0111-20-2

TITLE SPECIFICATION CONTROL DRAWING 82A0111 Date WIRE, RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE-INSULATED, LIGHTWEIGHT, GENERAL PURPOSE, 600 VOLT 6-5-13 Revision T This specification sheet forms a part of the latest issue of Raychem Specification 80. INSULATION - RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE CONDUCTOR - TIN-COATED COPPER TABLE I. CONSTRUCTION DETAILS PART NUMBER 1/ WIRE SIZE (AWG) CONDUCTOR STRANDING (number x AWG) DIAMETER OF STRANDED CONDUCTOR (in.) MINIMUM MAXIMUM FINISHED WIRE MAXIMUM RESISTANCE AT 20°C (ohms/1000 ft.) DIAMETER (in.) MAXIMUM WEIGHT (lbs/1000 ft.) 82A0111-28-* 28 42 x 44 .013 .017 71.4 .029 ± .003 1.0 82A0111-26-* 26 63 x 44 .017 .021 43.5 .033 ± .003 1.4 82A0111-24-* 24 105 x 44 .023 .027 28.2 .037 ± .003 2.1 82A0111-22-* 22 154 x 44 .029 .033 19.2 .043 ± .003 2.9 82A0111-20-* 20 154 x 42 .037 .043 11.7 .053 ± .004 4.2 82A0111-18-* 18 259 x 42 .047 .053 .064 ± .004 6.7 7.14 82A0111-16-* 16 259 x 40 .061 .067 4.53 .079 ± .004 10.2 82A0111-14-* 14 665 x 42 .078 .086 2.96 .099 ± .005 16.5 82A0111-12-* 12 665 x 40 .096 .106 1.89 .121 ± .006 24.8 82A0111-10-* 10 665 x 38 .126 .140 1.12 .157 ± .009 42.2 82A0111-8-* 8 665 x 36 .157 .173 .195 ± .010 66.3 .714 82A0111-6-* 6 1045 x 36 .192 .208 .490 .236 ± .011 102. 82A0111-4-* 4 1665 x 36 .265 .285 .326 .318 ± .013 169. 82A0111-2-* 2 1665 x 34 .325 .345 .204 .385 ± .014 252. 82A0111-1-* 1 2109 x 34 .370 .400 .163 .445 ± .019 317. 82A0111-0-* 0 2660 x 34 .435 .465 .133 .516 ± .020 407. 82A0111-00-* 00 3325 x 34 .485 .515 .102 .566 ± .020 502. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 2 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2013 Tyco Electronics Corporation,. All rights reserved. Revision SPECIFICATION CONTROL DRAWING Page 2 of 2 SCD Number T 82A0111 TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER 1/ MANDREL DIAMETER (inch) (± 3%) WEIGHT (lb) (± 3%) CROSSLINKING PROOF TEST CROSSLINKING PROOF TEST 82A0111-28-* .250 .125 82A0111-26-* .375 .125 82A0111-24-* .375 .250 82A0111-22-* .500 .375 82A0111-20-* .500 .500 82A0111-18-* .500 .500 82A0111-16-* .750 .750 82A0111-14-* 1.00 1.00 82A0111-12-* 1.50 1.50 82A0111-10-* 2.00 1.50 82A0111-8-* 3.00 2.00 82A0111-6-* 3.00 2.00 82A0111-4-* 4.00 2.50 82A0111-2-* 6.00 3.00 82A0111-1-* 8.00 4.00 82A0111-0-* 8.00 4.00 82A0111-00-* 8.00 4.00 WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level COLOR: White preferred CONCENTRICITY: 70% (minimum) CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours IDENTIFICATION AND COLOR STRIPING DURABILITY: 125 cycles (250 strokes) (minimum), 500 gram weight INSULATION ELONGATION AND TENSILE STRENGTH: AWG 28-26: Elongation, 75% (minimum) Tensile Strength, 3000 lbf/in² (minimum) AWG 24-10: Elongation, 75% (minimum) Tensile Strength, 3500 lbf/in² (minimum) AWG 8-00: Elongation, 125% (minimum) Tensile Strength, 3000 lbf/in² (minimum) INSULATION FLAWS: Spark Test, 1.5 kV (rms) at 3 kHz Impulse Dielectric Test, 6.0 kV (peak) INSULATION THICKNESS: AWG 28-16: .004 in. (minimum) AWG 14-10: .006 in. (minimum) AWG 8-00: .012 in. (minimum) SECANT MODULUS: (Test per ASTM D 882) AWG 28-10: 5.0 x 104 lbf/in2 (maximum) AWG 8-00: 4.0 x 104 lbf/in2 (maximum) 2% strain, 2 inch jaw separation, 0.2 inch/minute SHRINKAGE: 150 ± 3°C for 6 hours, AWG 28-10: 0.13 in. (maximum) in 12 inches AWG 8-00: 0.25 in. (maximum) in 12 inches VOLTAGE WITHSTAND (Post Environmental): 2500 volts (rms), 60 Hz PART NUMBER: The “*” in the part numbers in Tables I and II shall be replaced by a color code designator. 1/ Example: AWG 12, white; 82A0111-12-9 AWG 12, white with a black stripe; 82A0111-12-90 1/ See footer section on page 1