82A0116-24-9

TITLE SPECIFICATION CONTROL DRAWING WIRE, RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE-INSULATED, LIGHTWEIGHT, GENERAL PURPOSE, 600 VOLT 82A0116 Date Revision 2-25-13 A This specification sheet forms a part of the latest issue of Raychem Specification 80. INSULATION - RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE CONDUCTOR - NICKEL-COATED HIGH-STRENGTH COPPER ALLOY TABLE I. CONSTRUCTION DETAILS PART NUMBER 1/ WIRE SIZE (AWG) CONDUCTOR STRANDING (number x AWG) DIAMETER OF STRANDED CONDUCTOR (in.) MINIMUM MAXIMUM FINISHED WIRE MAXIMUM RESISTANCE AT 20°C (ohms/1000 ft.) DIAMETER (in.) MAXIMUM WEIGHT (lbs/1000 ft.) 82A0116-28-* 28 42 x 44 .013 .017 87.7 .029 ± .003 1.1 82A0116-26-* 26 63 x 44 .017 .022 62.6 .033 ± .003 1.5 82A0116-24-* 24 105 x 44 .023 .028 36.7 .037 ± .003 2.1 82A0116-22-* 22 154 X 44 .029 .035 24.5 .043 ± .003 2.9 82A0116-20-* 20 154 X 42 .037 .043 15.8 .053 ± .004 4.3 TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER 1/ MANDREL DIAMETER (inch) (± 3%) WEIGHT (lb) (± 3%) CROSSLINKING PROOF TEST CROSSLINKING PROOF TEST 82A0116-28-* .250 .125 82A0116-26-* .375 .125 82A0116-24-* .375 .250 82A0116-22-* .500 .375 82A0116-20-* .500 .500 Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 2 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2013 Tyco Electronics Corporation,. All rights reserved. Revision SPECIFICATION CONTROL DRAWING Page 2 of 2 A WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 200°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level COLOR: White preferred CONCENTRICITY: 70% (minimum) CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours IDENTIFICATION AND COLOR STRIPING DURABILITY: 125 cycles (250 strokes) (minimum), 500 gram weight INSULATION ELONGATION AND TENSILE STRENGTH: AWG 28-26: Elongation, 75% (minimum) Tensile Strength, 3000 lbf/in² (minimum) AWG 24-20: Elongation, 75% (minimum) Tensile Strength, 3500 lbf/in² (minimum) INSULATION FLAWS: Spark Test, 1.5 kV (rms) at 3 kHz Impulse Dielectric Test, 6.0 kV (peak) INSULATION THICKNESS: .004 in. (minimum) PRODUCT IDENTIFICATION: black ink only SECANT MODULUS (Test per ASTM D 882): 5.0 x 104 lbf/in2 (maximum) 2% strain, 2 inch jaw separation, 0.2 inch/minute SHRINKAGE: 200 ± 3°C for 6 hours, 0.13 in. (maximum) in 12 inches VOLTAGE WITHSTAND (Post Environmental): 2500 volts (rms), 60 Hz PART NUMBER: The “*” in the part numbers on page 1 shall be replaced by a color code designator. 1/ Example: AWG 24, white; 82A0116-24-9 AWG 24, white with a black stripe; 82A0116-24-90 1/ See footer section on page 1 SCD Number 82A0116