82A1131-22-MST3-9CS3022

SCD SPECIFICATION CONTROL DRAWING Title 82A1131 Date THREE CONDUCTOR CABLE, SHIELDED, JACKETED, 6-1-16 GENERAL PURPOSE, FLEXIBLE, 600 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 80. COMPONENT WIRES - 82A0111 SHIELD - TIN-COATED COPPER Revision C JACKET - RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE CABLE CONSTRUCTION DETAILS PART NUMBER 1/ CONDUCTOR SIZE (AWG) SHIELD SIZE (AWG) JACKET THICKNESS (inch) OUTSIDE DIAMETER (inch) MINIMUM NOMINAL NOMINAL MAXIMUM MAXIMUM WEIGHT (lbs/1000 ft.) 82A1131-28-* 28 38 .006 .008 .096 .101 8.5 82A1131-26-* 26 38 .006 .009 .106 .112 10.6 82A1131-24-* 24 38 .006 .009 .115 .121 13.4 82A1131-22-* 22 38 .006 .009 .128 .134 16.8 82A1131-20-* 20 38 .007 .010 .151 .159 22.8 82A1131-18-* 18 38 .008 .011 .177 .186 32.8 82A1131-16-* 16 38 .009 .013 .214 .224 47.3 82A1131-14-* 14 38 .010 .014 .259 .272 82A1131-12-* 12 38 .011 .016 .310 .326 103. 82A1131-10-* 10 36 .013 .019 .398 .418 171. 82A1131-8-* 8 36 .016 .023 .488 .513 260. 82A1131-6-* 6 34 .018 .026 .588 .617 395. 82A1131-4-* 4 34 .024 .034 .781 .820 645. 71.1 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 100% (minimum) Tensile Strength, 3000 lbf/in2 (minimum) JACKET FLAWS: Spark Test, 1500 volts (rms) Impulse Dielectric Test, 6.0 kV (peak) SECANT MODULUS (Test per ASTM D 882): 4.0 x 104 lbf/in2 (maximum), 2% strain, 2 inch jaw separation, 0.2 inch/minute SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute 1/ PART NUMBER: The "*" in the part numbers above shall be replaced by color code designators with a slash separating the component wire colors and a dash separating the component wire colors from the jacket color. Colors shown do not necessarily reflect the sequence of manufacturing. Example: AWG 20, orange, blue, and white component wires; white jacket: 82A1131-20-3/6/9-9 NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Page 1 of 1 DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2016 Tyco Electronics Corporation. All rights reserved.