82A1811-10-9-9

SCD SPECIFICATION CONTROL DRAWING Title 82A1811 Date ONE CONDUCTOR CABLE, SHIELDED, JACKETED, 2-3-16 GENERAL PURPOSE, FLEXIBLE, 600 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 80. COMPONENT WIRE - 82A0811 SHIELD - TIN-COATED COPPER Revision A JACKET - RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE CABLE CONSTRUCTION DETAILS JACKET THICKNESS (inch) OUTSIDE DIAMETER (inch) PART NUMBER 1/ CONDUCTOR SIZE (AWG) SHIELD SIZE (AWG) MAXIMUM WEIGHT (lbs/1000 ft.) MINIMUM NOMINAL NOMINAL MAXIMUM 82A1811-24-* 24 38 .005 .007 .075 .080 82A1811-22-* 22 38 .005 .007 .085 .090 8.5 82A1811-20-* 20 38 .006 .008 .097 .102 11.0 82A1811-18-* 18 38 .006 .008 .109 .114 14.7 82A1811-16-* 16 38 .007 .009 .127 .133 20.2 82A1811-14-* 14 38 .008 .010 .153 .161 29.9 82A1811-12-* 12 38 .008 .010 .174 .183 40.2 82A1811-10-* 10 38 .009 .012 .228 .239 67.7 82A1811-8-* 8 38 .011 .014 .275 .289 100. 82A1811-6-* 6 36 .011 .015 .328 .344 151. 82A1811-4-* 4 36 .014 .018 .416 .437 234. 82A1811-2-* 2 34 .016 .021 .501 .526 349. 82A1811-1-* 1 34 .017 .023 .560 .588 426. 82A1811-0-* 0 34 .019 .025 .634 .666 534. 6.6 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level CROSSLINKING PROOF TEST: 300 ± 3°C for 7 hours DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 100% (minimum) Tensile Strength, 3000 lbf/in2 (minimum) JACKT FLAWS: Spark Test, 1500 volts (rms) Impulse Dielectric Test, 6.0 kV (peak) SECANT MODULUS (Test per ASTM D 882): 4.0 x 104 lbf/in2 (maximum), 2% strain, 2 inch jaw separation, 0.2 inch/minute SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute 1/ PART NUMBER: The "*" in the part numbers above shall be replaced by color code designators with a dash separating the component wire color from the jacket color. Example: AWG 22, white component wire; white jacket: 82A1811-22-9-9 NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Page 1 of 1 DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2016 Tyco Electronics Corporation. All rights reserved.