te.com
82
Constant Voltage
SPECIFICATIONS
Features
O-Ring Mount/Threaded Process
Fittings
-40ºC to +125ºC Operating
Temperature Range
Up to ±0.1% Pressure Non Linearity
Solid State Reliability
Applications
Medical Instruments
Process Control
Fresh & Waste Water Measurements
Partial Vacuum Gas Measurement
Pressure Transmitters
Tank Level Systems (RV & Industrial)
316L SS Pressure Sensor
19mm Diameter Package
0 - 100mV Output
Absolute and Gage
Temperature Compensated
The 82 constant voltage is a 19 mm small profile, media compatible,
piezoresistive silicon pressure sensor packaged in a 316L stainless
steel housing. The 82 constant voltage can be configured for O-ring
mounting or threaded process fittings and is designed for OEM
applications where compatibility with corrosive media is required.
The sensing package utilizes silicone oil to transfer pressure from
the 316L stainless steel diaphragm to the sensing element. A
ceramic substrate is attached to the package that contains lasertrimmed resistors for temperature compensation and offset
correction.
Please refer to the 82 uncompensated and compensated
datasheets for more information on different features of the 82.
CLICK HERE ›
CONNECT WITH A SPECIALIST
TE CONNECTIVITY SENSORS /// 82CV
REVA 10/2021
Page 1
82
Digital Output Pressure Sensor
Specifications
Unless otherwise specified, Supply Voltage: 10 VDC; Ambient Temperature: 25°C
≥015PSI
≤005PSI
PARAMETERS
Span
Zero Pressure Output
Pressure Non Linearity
Pressure Hysteresis
MIN
TYP
MAX
1psi: MIN77, TYP 80, MAX83
5psi: MIN98, TYP100, MAX102
-2.0
0
2.0
1psi: -0.30 TO +0.30
5psi: -0.20 TO +0.20
MIN
TYP
MA
X
UNITS
NOTES
99
100
101
mV
1
-1.0
0
1.0
mV
1
-0.1
-
0.1
%Span
2
-0.10
±0.02
0.10
-0.05
±0.02
0.05
%Span
-
±0.02
-
-
±0.02
-
%Span
Input Resistance
5.5
9.0
12.5
5.5
9.0
12.5
KΩ
Output Resistance
4.0
-
7.0
4.0
-
6.0
KΩ
Temperature Error – Span
-1.0
-
1.0
-1.0
-
1.0
%Span
3
Temperature Error – Offset
Thermal Hysteresis – Span
-1.0
-
1.0
-1.0
-
1.0
%Span
3
-0.25
±0.05
0.25
-0.25
±0.05
0.25
%Span
3
Thermal Hysteresis – Offset
-0.25
±0.05
0.25
-0.25
±0.05
0.25
%Span
3
Long Term Stability – Span
-
±0.10
-
-
±0.10
-
%Span
Long Term Stability – Offset
-
±0.25
-
-
±0.10
-
%Span
Supply Voltage
Output Load Resistance
-
10
14
-
10
14
V
4
5M
-
-
5M
-
-
Ω
5
Insulation Resistance (50Vdc)
50M
-
-
50M
-
-
Ω
6
Output Noise (10Hz to 1KHz)
-
1.0
-
-
1.0
-
µV p-p
Response Time (10% to 90%)
-
0.1
-
-
0.1
-
ms
Repeatability
Pressure Overload
1psi: 10x MAX
5psi: 3x MAX
-
-
3x
Rated
Pressure Burst
1psi: 12x MAX
5psi: 4x MAX
-
-
4x
Rated
Compensated Temperature
1psi: 0 TO 50
5psi: 0 TO 70
-20
85
°C
7
Operating Temperature
-20
-
70
-40
-
125
ºC
8
Storage Temperature
-40
-
125
-40
-
125
ºC
8
Media – Pressure Port
Liquids and Gases compatible with 316L Stainless Steel and Buna-N
Notes
1. Measured at vacuum for absolute (A), ambient for gage (G).
2. Best fit straight line.
3. Over the compensated temperature range with respect to 25°C.
4. Guarantees output/input ratiometricity.
5. Load resistance to reduce measurement errors due to output loading.
6. Between case and sending element.
7. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer.
8. Maximum temperature range for product with standard cable and connector is -20 to +105°C.
9. Standard Gage units are not recommended for vacuum applications, For vacuum applications below 1/2 atmosphere, consult
factory.
10. Device Marking:
Each part shall be identified with Model Number, Pressure Range, Type, Lot Number, Serial Number and Date Code
11. Shipping/Packaging
The Stainless Steel Diaphragm is protected by a plastic cap (No Fitting Options). Each unit will be packaged individually in a plastic
vial with anti-static foam.
12. Direct mechanical Contact with diaphragm is prohibited. Diaphragm surface must remain free of defects (scratches, punctures,
dents, fingerprints, etc) for device to operate properly. Caution is advised when handling parts with exposed diaphragms. Use
protective cap whenever devices are not in use.
TE CONNECTIVITY SENSORS /// 82CV
REVA 10/2021
Page 2
82
Digital Output Pressure Sensor
Dimensions
Dimensions are in inches
mm
TE CONNECTIVITY SENSORS /// 82CV
REVA 10/2021
Page 3
82
Digital Output Pressure Sensor
RECOMMENDED MOUNTING DIMENSIONS
APPLICATION SCHEMATIC
TE CONNECTIVITY SENSORS /// 82CV
REVA 10/2021
Page 4
82
Digital Output Pressure Sensor
ORDERING INFORMATION
Part Number
82 CV– 030 G – 3 C T
Pressure Range [psi]
001
(Gage Only)
005
015
030
050
100
300
500
G
A
Vent
Tube
No Tube
T
[Blank]
P
R
C
Electrical
Solder Pads
Ribbon cable
Cable w/ Connector
[Blank]
1
2
3
9
Pressure Type
Gage
Absolute
Fitting Type
No Fitting, Weldable
1/4-18 NPT
1/8-27 NPT
7/16-20 UNF
1/4-19 BSP
Refer to Fitting Table for more information
CLICK HERE ›
CONNECT WITH A SPECIALIST
NORTH AMERICA
Tel +1 800 522 6752
EUROPE
Tel +31 73 624 6999
ASIA
Tel +86 0400 820 6015
te.com/sensors
TE Connectivity, TE, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might
be trademarks of their respective owners
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However,
TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall
only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental,
indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation
to determine the suitability of each such product for the specific application.
© 2021 TE Connectivity Corporation. All Rights Reserved.
Version A7 02/2021
TE CONNECTIVITY SENSORS /// 82CV
REVA 10/2021
Page 5
很抱歉,暂时无法提供与“82CV-100A-R”相匹配的价格&库存,您可以联系我们找货
免费人工找货