86-030A-C

86 Compensated • 316L SS Pressure Sensor • Small Profile • 0 - 100mV Output • Absolute and Gage • Temperature Compensated I heard DESCRIPTION The 86 compensated is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 86 compensated is designed for o-ring mounting and OEM applications where compatibility with corrosive media is required. The sensing package utilizes silicon oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. A ceramic substrate is attached to the package that contains laser-trimmed resistors for temperature compensation and offset correction. An additional laser trimmed resistor is included which can be used to adjust an external differential amplifier and provide span interchangeability to within ±1%. Please refer to the 86 uncompensated and constant voltage datasheets for more information on different features of the 86. FEATURES • • • • • APPLICATIONS O-Ring Mount -40ºC to +125ºC Operating Temperature Range ±0.2% Pressure Non Linearity 1.0% Interchangeable Span (provided by gain set resistor) Solid State Reliability • • • • • • Medical Instruments Process Control Fresh & Waste Water Measurements Partial Vacuum Gas Measurement Pressure Transmitters Tank Level Systems (RV & Industrial) STANDARD RANGES Range 0 to 5 0 to 15 0 to 30 0 to 50 0 to 100 0 to 300 0 to 500 86C psig • • • • • • • psia • • • • • • • www.meas-spec.com 1/4 August 2011 86 Compensated PERFORMANCE SPECIFICATIONS Supply Current: 1.5mA Ambient Temperature: 25°C (unless otherwise specified) PARAMETERS Span Zero Pressure Output ≥015PSI 005PSI MIN TYP MAX 50 100 -2.0 0 0.2 -0.1 ±0.02 0.10 -0.05 6.5K 2.0K Pressure Non Linearity -0.2 Pressure Hysteresis -0.10 Repeatability NOTES TYP MAX 150 75 100 150 mV 1 2.0 -1.0 0 1.0 mV 2 0.1 %Span 3 ±0.02 0.05 %Span ±0.02 ±0.02 %Span Ω 6.0K Ω 2.5K Output Resistance 4.0K 7.0K 4.0K Temperature Error – Span -1.0 1.0 -0.75 0.75 %Span 4 Temperature Error – Offset -1.5 1.5 -0.50 0.50 %Span 4, 5 Thermal Hysteresis – Span -0.25 ±0.05 0.25 -0.25 ±0.05 0.25 %Span 4 Thermal Hysteresis – Offset -0.25 ±0.05 0.25 -0.25 ±0.05 0.25 %Span 4 ±0.10 Long Term Stability – Offset 5M Insulation Resistance (50Vdc) 0.5 50M 1.5 ±0.10 2.0 0.5 %Span/Year 1.5 2.0 50M 1.0 Response Time (10% to 90%) 0.1 Pressure Overload %Span/Year 5M Output Noise (10Hz to 1KHz) 1.0 0.1 50 6 Ω 7 Ω 8 ms 4X 0 mA uV p-p 3X Pressure Burst Compensated Temperature ±0.10 ±0.25 Supply Current Output Load Resistance 3.5K 5.8K Input Resistance Long Term Stability – Span 5.0K UNITS MIN 3X Rated 4X Rated -20 +85 °C 9 Operating Temperature -20 +70 -40 +125 ºC 10 Storage Temperature -50 +125 -50 +125 ºC 10 Media – Pressure Port Liquids and Gases compatible with 316/316L Stainless Steel Media – Reference Port Compatible with Silicon, Pyrex, Gold, Fluorosilicone Rubber, and 316/316L Stainless Steel Notes 1. For amplified output circuits, 3.012V ±1% interchangeability with gain set resistor. See application schematic. 2. Measured at vacuum for absolute (A) and at ambient for gage (G). 3. Best fit straight line. 4. Over the compensated temperature range with respect to 25°C. 5. 15-psi range sensors have a temperature error of °0.75% (max) of zero from -20°C to +85°C. 6. Guarantees output/input ratiometricity. 7. Load resistance to reduce measurement errors due to output loading. 8. Between case and sensing element. 9. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer. 10. Maximum temperature range for product with standard cable and connector is -20°C to +105°C. 86C www.meas-spec.com 2/4 August 2011 86 Compensated DIMENSIONS CONNECTIONS 86C www.meas-spec.com 3/4 August 2011 86 Compensated APPLICATION SCHEMATIC ORDERING INFORMATION 86 - 005 G - C T Vent (T = Tube, Blank = No Tube) Electrical (C = Ribbon Cable with Connector, R = Ribbon Cable, P = Solder Pads) Type (A = Absolute, G = Gage) Pressure Range Model NORTH AMERICA EUROPE Measurement Specialties 45738 Northport Loop West Fremont, CA 94538 Tel: 1-800-767-1888 Fax: 1-510-498-1578 Sales: pfg.cs.amer@meas-spec.com Measurement Specialties (Europe), Ltd. 26 Rue des Dames 78340 Les Clayes-sous-Bois, France Tel: +33 (0) 130 79 33 00 Fax: +33 (0) 134 81 03 59 Sales: pfg.cs.emea@meas-spec.com ASIA Measurement Specialties (China), Ltd. No. 26 Langshan Road Shenzhen High-Tech Park (North) Nanshan District, Shenzhen 518057 China Tel: +86 755 3330 5088 Fax: +86 755 3330 5099 Sales: pfg.cs.asia@meas-spec.com The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer’s technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others. 86C www.meas-spec.com 4/4 August 2011