9-1617514-2

CII Low Signal Relays Double Pole, Electrically Held, 2 Amps and Less (Continued) .150 Grid-space Relays Type 3SBC (2PDT) Standard Product Facts n Low profile… only 0.32 inches high n Internal diode for coil transient suppression and transistor driven models available n Qualified to MIL-R-39016/13 n RF designs available The .150 Grid-space relay — only 0.32 inches high — saves space in electronic packaging. The pin spacing allows you to insert the relay with no intermediate pin spreaders as well as meet applicable military specifications. Operating Characteristics Contact Ratings — DC resistive — 2 amps at 28 volts (50,000 operations) 1 Amp @ 28 V (100,000 operations) DC inductive — 0.5 amps at 28 volts, 200 mH AC resistive — 0.5 amps at 115 volts AC — 0.125 amps at 115 volts (case grounded) Low-level — 50 µA at 50 mV Peak AC or DC Contact Resistance — 0.050 ohms max.; 0.150 ohms after life test Life — 100,000 operations at rated loads listed; 1,000,000 operations at low-level loads Operate Time — 4 ms max. Release Time — 4 ms max. Contact Bounce — 1.5 ms Dielectric Strength — 500 volts rms at sea level; 350 volts rms at 70,000 feet and above Insulation Resistance — 1,000 megohm min. over temperature range 1 CII Low Signal Relays 135 mW 2PDT 50 mW (Form AB) 1 PNC–1 PNO Electrical Characteristics Environmental Characteristics Vibration — 30G, to 3000 Hz Shock — 100 G at 11 ms Temperature — -65°C to +125°C See page 1-44 for Mounting Forms, Terminals and Circuit Diagrams. *Values listed are factory test and inspection data. User should allow for meter variations. †At nominal resistance plus 10%. ‡Applicable over the operating temperature range in circulating air. See Page 1-42 for ordering instructions. * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-41 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Low Signal Relays Double Pole, Electrically Held, 2 Amps and Less (Continued) .150 Grid-space Hybrid Relays Single Diode, Dual Diode Type 3SBC (2PDT) 135 mW Product Facts n Low profile… only 0.32 inches high n 50 milliwatt forms available n Qualified to MIL-R-39016/37 n Qualified to MIL-R-39016/38 n RF designs available The hybrid .150 Grid-space relay — only 0.32 inches high — saves space in electronic packaging. The pin spacing allows you to insert the relay with no intermediate pin spreader. Electrical Characteristics Operating Characteristics Contact Ratings — DC resistive — 2 amps at 28 volts (50,000 operations) 1 Amp @ 28 V (100,000 operations) DC inductive — 0.5 amps at 28 volts, 200 mH AC resistive — 0.5 amps at 115 volts AC — 0.125 amps at 115 volts (case grounded) Low-level — 50 µA at 50 mV Peak AC or DC Contact Resistance — 0.050 ohms max.; 0.150 ohms after life test Life — 100,000 operations at rated loads listed; 1,000,000 operations at low-level loads Operate Time — 4 ms max. Release Time — 6 ms max. Contact Bounce — 1.5 ms Dielectric Strength (Note 1) — 500 volts rms at sea level; 350 volts rms at 70,000 feet and above Insulation Resistance (Note 1) — 1,000 megohm min. over temperature range Environmental Characteristics Vibration — 30G, to 3000 Hz Shock — 100 G at 11 ms Temperature — -65°C to +125°C Semiconductor Characteristics at 25°C Diode — Max. Negative Transient — 1.0 volt Breakdown Voltage — 100 VDC @ 10 µA Max. Leakage Current — 1 µA @ 50 VDC See page 1-44 for Mounting Forms, Terminals and Circuit Diagrams. Ordering Instructions Example: The relay selected in the example is a FORM AB .150-grid relay, current calibrated, end bracket mounting with 0.13-inch solder hook header, 210 ohms coil resistance, and 50 mW sensitivity. By choosing the proper code for each of these relay characteristics, the catalog number is 3SBC6131E2. The letter R following sensitivity code indicates relay received 5000 operation miss-test. Ex. 3SBC6131E2R. Note: Relays specified by catalog numbers (per above directions) are general use items controlled by catalog specifications. Relays to be controlled by customer drawings — or relays having requirements not covered in this publication — will be assigned special catalog numbers upon request. * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-42 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com