AE-770

Application Equipment IR-1759 MiniRay Infrared Heating Tool Product Facts n Small, lightweight, fan-cooled unit n Small profile for installation where space is restricted n Handheld operation n Focused heat n Quiet, efficient IR operation n CE approved n RoHS compliant Applications Used for installing SolderSleeve devices and SolderTacts contacts. * Control box not shown The MiniRay tool is a hand held Infrared heating tool designed for installing shield terminators, splices and approved IR repair and tubing products.* The tool is portable, lightweight and is convenient for use where work space is restricted. The hand tool is fan cooled and has low heat emission as the lamp is only energized on demand. A duty cycle up to 50% is permissible with a maximum heating time of 30 seconds. Two versions of the hand tool are available: n IR-1759-MK4/A Standard aperture recommended for products up to 6 mm diameter. n IR-3104-MK4/A Large aperture for products up to 9 mm diameter. 1 Approved by the U.S. Navy for use on fueled aircraft. Available in: Both versions of the tool will accept larger diameter components but uniform heating is then not assured. The battery box controller is designed for remote areas, where more portability is required. This battery-powered controller can install approximately 50, 30 second installations before recharging is required. The ED-7-001-MK4-230V-50HZ and ED-7-002-MK4-110V60HZ Control units provide controls for both power and time and are suitable where the use of pre-set installation conditions is required. Up to 20 memory locations are available for the storage of time/power values. A trigger switch is used to initiate each cycle. The controller can also be used in a manual mode with the operator controlling the duration of the heating cycle via the trigger switch. The ED-7-CONT-230/110VMK4 controller is a more simpler unit, with no variable time, or variable power memory functions, and maintains power to the lamp for as long as the trigger switch remains depressed. The tool can be used with either 230V or 110V (nominal) voltage supply. The product being installed is visible during the heating cycle. An optical filter eliminates the unwanted UV emissions and excess visible light reducing the glare for the operator. A product kit is available, see page 10-19 for ordering information. *Contact your local TE representative for details. Americas1 Europe Asia Pacific n n n 10-18 Catalog 1654025 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com Application Equipment IR-1759 MiniRay Infrared Heating Tool (Continued) Technical Specifications IR-1759 / IR-3104 HAND TOOLS Supply Voltage Weight Typical Operating Temperature Typical Heating Time Lamp Type, Power & Life - Typical values Noise Power Cord Length 21.5 VAC nominal 1.1 kg 500˚C 15 seconds 250 W Tungsten Halogen average life 10,000 cycles @ 50% duty cycle 51 dB (A) 3.1 m ED-7-CONT-230/110V-MK4 / ED-7-001-MK4-230V-50HZ / ED-7-002-MK4-110V-60HZ and ED-7-BATTBOX-MK4-230/110V Product Range Supply Voltage: ED-7-001 & 002 ED-7-CONT-230/110V-MK4 ED-7-BATTBOX-MK4-230/110V Input Current: ED-7-001 & 002 ED-7-CON-230/110V-MK4 Dimensions WxHxL Weight: ED-7-001 & 002 ED-7-CONT-230/110V-MK4 ED-7-BATTBOX-MK4-230/110V Timer Adjustment (ED-7-001/002 only) Output Voltage: ED-7-001 & 002 ED-7-CONT-230/110V-MK4 ED-7-BATTBOX-MK4-230/110V Voltage Output Control Accuracy (with ± 10% input variation): ED-7-001 & 002 ED-7-CONT-230/110V-MK4 ED-7-BATTBOX-MK4-230/110V Lamp “Hold-On” Voltage: ED-7-001 & 002 ED-7-CONT-230/110V-MK4 ED-7-BATTBOX-MK4-230/110V Memory Locations (ED-7-001&002 only) 3.5 VAC N/A N/A 20 Shield Terminators For Other TE Products D-10X, SO63, SO96 Discuss with Product Management 230 VAC 50 Hz & 110 V 50/60 Hz 230 VAC 50 Hz or 110 V 50/60 Hz 2 x 12V batteries 4 A & 10 A 6.3 A 160 x 120 x 250 mm 6.2 kg 8.0 kg 8.5 kg 1-250 seconds 16-24 VAC (dependent on program) 21.5 VAC 24V DC nominal ± 3% ± 0.5V (120V/230V supply) N/A (dependent upon charge) 10 Application Equipment Ordering Information Description Kit Part Number IR heater, reflector to fit standard IR1759-MK4-AT3130-EDCONT aperture, Standard V-block plus a Non-Timed Control Box 230V or 110V supply 10-19 Catalog 1654025 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com Application Equipment IR-1759 MiniRay Infrared Heating Tool (Continued) Parts, Accessories and Spare Parts List Description Part Number Guideline Comments IR1759-Mk4/A /IR1759-Mk3/A IR1759-Mk4-At3130-EDCont CF0025-000 Infra Red Heater Standard Aperture RoHS compliant. Replaces 986899-000 CF0024-000 Infra Red Heater, Reflector to fit standard aperture, IR3104-Mk4/A CF5497-000 Infra Red Heater Large Aperture RoHS compliant. Replaces 898738000/IR1759-Mk3-At3130standard vee block, none timed control EDCont RoHS compliant. Replaces 035343-000-000 / IR3104-Mk3/A ACCESSORIES AT-3191 AT-3134 AE-897 AD-7-100 AT-3147 AT-3132-Mk31/1 588701-000 988303-000 966953-000 176247-000 988328-000 879865-000 AT-3131 988300-000 Reflector to fit Standard Aperture, Special Vee Block Reflector to fit Large Aperture, Standard Vee Block Conversion kit from Standard to Large Aperture External Viewing Window Reflector to fit Large Aperture with Clamps Reflector to fit Standard Aperture with Clamps and with 5 mm wide mask Reflector to fit Standard Aperture AT-3132 988301-000 Reflector to fit Standard Aperture with Clamps AT-3130 988299-000 Reflector to fit Standard Aperture, Standard SPARE PARTS AE-226 AE-424 AE-1367 NAE-143-3 AE-153 AD-1360 AE-205 988314-000 547918-000 338605-000 988208-000 988285-000 106503-000 988596-000 Outer Reflector Mirror for AT-3134/AT-3147 Inner Reflector for Standard Aperture Hook Bulb 250W/24V Inner Reflector for Large Aperture Standard Thermal Shield Outer Reflector Mirror for AT-3130/AT3131/AT-3132 NAE-109-2 AES-IR1759-100-Filter-Dul IR1759/3104-Cable-Asy 988382-000 431468-000 585643-000 AE-770 AE-900 NAE-152-1 AT-3130-AE204-AE203-10SET 747525-000 277774-000 988204-000 481321-000 Lamp Holder Filter for Standard Aperture Trigger PCB, Cable Assembly, Includes Lamp Holder and Fan Optic Bloc for IR1759 Filter Spring IR1759 Fan Replacement for Vs for AT3130 V Block AES-IR1759-300-FLTR-LRG F52511-000 Filter for Large Aperture Heatgun Aerospatiale “special” reflector. Reflector for IR1759 for SolderTact products with a vee block at one end Reflector for IR1759 for SolderSleeve products using clamps to hold wire in place Reflector for IR1759 for SolderSleeve products using Vee Block gravity to hold wire in place AE-203 & AE-204 are two halves of AT-3130 V Block, supplied in quantities of 10 sets 10-20 Catalog 1654025 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com Application Equipment IR-1759 MiniRay Infrared Heating Tool (Continued) Parts, Accessories and Spare Parts List (continued) Description Part Number ED-7-CONT-230/110V-Mk4 CF0026-000 ED-7-BATTBOX-MK4-230/110V CF0200-000 Guideline Comments None Timed Control Box - 230V or 110V Supply Replaces ED-7-Cont-230/110V 684886-000 Battery Powered Controlled for IR-1759 (230V or Replaces ED-7-BatteryBox- 110V Supply) - RoHS compliant version not included. When purchasing the 230/110V/448969-000. Batteries controller, order ED-7-Batt-Battery 755928-000 also. ED-7-001-MK4-230V-50HZA CF0199-000 Control Box 230V, with Timer Replaces Ed-7-001-Mk2-230V50Hz/869233-000 ED-7-002-MK4-110V-60HZA CF0201-000 Control Box 110V, with Timer Replaces Ed-7-002-Mk2-110V60Hz/903553-000 ACCESSORIES ED-7-Cont-Front-Panel 619690-000 Front Panel and Display PCB including Triac and ED-7-Cont-Transformer 139128-000 Transformer Inductor ED-7-Batt-Battery 755928-000 Battery Pack ED-7-Batt-Front-Panel 132692-000 Front Panel and Display PCB with Logic PCB and Power PCB ED-7-001/2-Transformer 584781-000 ED-7-001 & ED-7-002 Transformer ED-7-001/2-Front-Panel 524325-000 ED-7-001 & ED-7-002 Front Panel 10 Application Equipment 10-21 Catalog 1654025 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com