C8D36PF29023

Card Edge Connectors Catalog 1654080 Issued 7-03 Card Edge Connectors Introduction This catalog contains product descriptions of AMP Card Edge Connectors. These connectors are presented in three groups: Solder Type Board-toBoard, Press-fit Board-toBoard, and Wire-to-Board connectors. To assist you in the selection of the appropriate connector for your application, a selection guide is provided at the beginning of each section. See the Table of Contents on the following page for the exact location. A comprehensive description and features of a partic- Need more information? Call Technical Support at the numbers listed at the bottom of the catalog pages. Technical Support is staffed with specialists well versed in Tyco Electronics products. They can provide you with: Technical Support Catalogs ■ Technical Documents ■ Product Samples ■ Tyco Electronics Authorized Distributor Locations ular printed circuit board connector family are provided at the beginning of that section. Various technical documents are referenced in the connector family sections and are listed and described at the rear of this catalog. The Tyco Electronics products presented in this catalog are designed and manufactured according to the highest possible standards of quality and craftsmanship. They offer optimum reliability at the lowest possible cost. Dimensioning: Dimensions are in inches and millimeters unless specified otherwise. Values in brackets are metric equivalents. Metric symbols used are: m (meter) mm (millimeter) mm2 (square millimeter) kg (kilogram) C (Celsius) N (newton) Note: Dimensions in this catalog are for reference purposes only. Customer drawings are available upon request. ■ ■ © Copyright 1992, 1996 and 2002 by Tyco Electronics. All Rights Reserved. AMP, ACTION PIN, AMP-DURAGOLD, AMP-LEAF, AMP-O-LECTRIC, AMP-O-MATIC, AMPOMATOR, AMP PACE, CERTI-CRIMP, DUO-TYNE, ECONOMATE, TELEDENSITY, and TYCO are trademarks. Other products, logos, and company names mentioned herein may be trademarks of their respective owners. Produced under a Quality Management System certified to ISO 9001 A copy of the certificate is available upon request 2 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Table of Contents Solder Type Board-to-Board Connectors Introduction………………………………………………………………………………………2 Selection Guide ………………………………………………………………………………4-6 Standard Edge Series Connectors Standard Edge .050 PCI Card Edge Connectors ………………………………………7-10 Standard Edge .050 Series Connectors ………………………………………………11-14 Standard Edge II Connectors ……………………………………………………………15-27 Cantilever Beam Dip Solder Tails Overview ……………………………………………………28 .100" [2.54] Centerline ……………………………………………………………………29-34 .125" [3.18] Centerline ……………………………………………………………………35-37 .156" [3.96] Centerline ……………………………………………………………………38-40 Modified Bellows Contact Overview ……………………………………………………………41 .100" [2.54] Centerline ……………………………………………………………………42-47 .125" [3.18] Centerline ……………………………………………………………………48-52 .156" [3.96] Centerline ……………………………………………………………………53-56 Polarization Keys ………………………………………………………………………………57 Standard Daughter Card Layout …………………………………………………………………57 Low Profile Connectors ……………………………………………………………………58-63 Twin Leaf Mother Board Connectors ………………………………………………………64-72 Rotary Cam ZIF Connectors …………………………………………………………………73-82 Linear ZIF Connectors ………………………………………………………………………83-96 Press-Fit Board-to-Board Connectors ACTION PIN Press-Fit Contacts ……………………………………………………………97 AMP PACE Connectors …………………………………………………………………98-115 TELEDENSITY Connectors ……………………………………………………………116-118 ECONOMATE Connectors ……………………………………………………………119-126 Cantilever Beam Press-Fit Connectors Overview ……………………………………………127 .050" [1.27] High Density ………………………………………………………………128-129 .100" [2.54] Centerline …………………………………………………………………130-140 .125" [3.18] Centerline …………………………………………………………………141-144 .156" [3.96] Centerline …………………………………………………………………145-148 Application Tooling ……………………………………………………………………149-151 Wire-to-Board Connectors Introduction …………………………………………………………………………………152 Selection Guide ………………………………………………………………………………153 Crimp Snap Twin Leaf Connectors …………………………………………………154-163 AMP-LEAF Connectors…………………………………………………………………164-172 High Current Connectors ………………………………………………………………173-176 DUO-TYNE Flag Connectors …………………………………………………………177-180 Printed Circuit Board Connector Hood Assemblies ………………………………181-183 Application Tooling ……………………………………………………………………184,185 Technical Documents ……………………………………………………………………186,187 Part Number Index ………………………………………………………………………188-201 Tyco Electronics Related Product Information ………………………………………………202 3 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Selection Guide, Board-to-Board Connectors Introduction Board-to-board (mother/ daughter board) connectors are ideally suited to backplane wiring or any other application requiring the circuit connection of one printed circuit board to another. Designed to shorten manufacturing time and reduce applied costs, these one-step, pre-assembled connectors are ready for mounting and mass insertion. Board-to-board connectors come in a range of contact centerline spacings of .050 [1.27] to .156 [3.96]. A wide range of dual position sizes and post styles are available. One family of connectors features zero insertion force of the daughter board, along with a choice of actuating devices. A variety of housing and contact materials further expands the choice of connectors available to meet many application requirements. Many of the connectors are available with the proven and reliable ACTION PIN contact. This unique contact has superior electrical and physical characteristics that are top of the line in the industry. Standard Edge .050 Series PCI Connectors (Pages 7-10) To help in choosing a connector for your application, a Selection Guide is provided on pages 4 through 6. Standard Edge .050 Series Connectors (Pages 11-14) Standard Edge II Connectors (.100 and .125 Centerline) (Pages 15-27) .350 [8.89] .300 [7.62] .368 [9.35] .155 [3.94] .300 [7.62] .610 [15.49] .610 [15.49] .170±.020 [4.32±0.51] .610 [15.49] .315 [8.00] .170±.020 [4.32±0.51] Centerlines .050 [1.27] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] X X X X Tail Styles Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount X X X X X X 4 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Selection Guide, Board-to-Board Connectors (Continued) Standard Edge II Connectors (.150 Centerline) (Pages 15-27) Cantilever Beam Connectors Standard Housing (Pages 28-40) Cantilever Beam Connectors Scoop Housing (Pages 28-40) .370 [9.40] .390 [9.91] .054–.070 [1.37-1.78] .045 [1.14] .145 [3.68] .015 [0.33] .008 [.203] .365 [9.27] .054 to .071 [1.37 to 1.80] .020±.010 [.51±.25] .300 [7.62] .610 [15.49] .705 [17.91] .200±.020 [5.08±0.51] .135±.020 [3.43±0.51] .200 [.508] .395 or .510 [10.03 or 12.95] .015 [0.41] Centerlines X X X X X X X X X X X .050 [1.27] .0625 [1.588] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] Tail Styles X Low Profile Connectors (Pages 58-63) Modified Bellows Connector (Pages 41-56) .368 [9.35] .054-.071 [1.37-1.80] .300 [7.62] .610 [15.49] Twin Leaf Mother Board Connectors (Pages 64-72) .437 [11.10] .125 [3.18] .460 [11.68] .165 [4.19] Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount .400 [10.16] .150 [3.81] .610 [15.49] .235 [5.97] .200 [5.08] .025 [.63] Centerlines X X X X X X X X X X X X X X .050 [1.27] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] Tail Styles X Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount 5 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Selection Guide, Board-to-Board Connectors (Continued) Rotary Cam ZIF Connectors (Pages 73-82) Linear ZIF Connectors (Pages 83-96) .140 [3.56] AMP PACE Connectors, Card Scoop Housing (Pages 98-115) .475 [12.07] .450 [11.43] A .440 [11.18] .150 [3.81] .234 [5.94] .845 [21.46] .815 [20.70] .645 [16.38] .848 [21.54] .490 [12.45] .460 [11.68] .598 [15.19] .370 [9.40] .345 [8.76] .130 [3.30] .100 x .200 = .390 [9.91] A .125 x .125 = .420 [10.67] .125 x .200 = .420 [10.67] Centerlines .050 [1.27] .0625 [1.588] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] X X X X X X X Tail Styles Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount X X X X AMP PACE Connectors, Standard Housing (Pages 98-115) X X X X High Density Press Fit Connector For .093 Cards (Pages 128-129) ECONOMATE Connectors (Pages 119-126) .400 [10.16] A .234 [5.94] .066 [1.68] .415 [10.54] .545 [13.84] .545 [13.84] .181 [4.60] .610 [15.49] .421 .461 [10.69] [11.71] .130 [3.30] A .100 x .100 = .380 [9.65] .100 x .200 = .360 [9.14] .125 x .250 = .410 [10.41] .156 x .200 = .360 [9.14] Centerlines .050 [1.27] .0625 [1.588] .100 [2.54] .125 [3.18] .150 [3.81] .156 [3.96] X X X X X X Tail Styles Solder Right-Angle Solder Wrap-Type Card Extender Solder Eyelet Press-Fit Surface-Mount X X X X 6 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors Product Facts ■ ■ ■ ■ High density .050 [1.27] centerline contact spacing Easy mating of high circuit count daughter boards Polarizing web for positive board-to-connector registration Choice of plastic pylons or metal holddowns Connectors that support PCI expansion cards are derived from those on the MicroChannel Architecture (MCA) bus. The MCA connectors are well defined and have proven value and reliability. There are four connectors that can be used depending upon the PCI implementation. The differences between these connectors are 32 bit and 64 bit, and the 5 volt and 3.3 volt signaling environments. PCI-X is a version of PCI at 133 MHz which is under development and employs standard PCI connectors. PCI-X is limited to 1 slot versus 4 slots of PCI. A key differentiates the signaling environment voltages. The same physical connector is used for the 32 bit signaling environments. In one orientation, the key accepts 5 volt boards. When rotated 180°, the connector accepts 3.3 volt signaling boards. The pin numbering of the connector changes for the different signaling environments to maintain the same relative position of signals on the connector. Performance Specifications: Durability—Tested to 100 mating cycles Mating Force—8 oz [2.22 N] max. per contact pair Unmating Force—.5 oz [0.14 N] min. per contact pair Contact Resistance—20 milliohms max. (initial) 30 milliohms max. (final) Insulation Resistance— 1000 megohms min. Dielectric Withstanding Voltage— 500 VAC (at sea level) Capacitance—2 picofarads max. Current Rating—1 ampere max. Voltage Rating—203 VAC Thermal Shock— –55°C to +85°C for 5 cycles Mixed Flowing Gas—Class II with mated board for 20 days Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Qualification Test Report 501-203 7 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors 64 Bit, 5 Volt Signaling Plastic Pylons 92 Dual Positions with 3 Plastic Pylons or 3 Metal Holddowns .350 [8.89] 5.040 [128.02] Material and Finish: Housing—High temperature thermoplastic 94V-0 rated, white Contacts—Phosphor bronze, plated as follows: Plating B—Duplex plated .000015 [0.00038] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating C—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .035 [0.89] (2 Plcs.) L .300 [7.62] 35° (2 Plcs.) .610 [15.49] .170±.020 [4.32±0.51] L ±.010 W [±0.25] Typ. .075 [1.90] (2 Plcs.) See Note. .050 48 Spaces at [1.27] .060 [1.52] Typ. .150 [3.81] 31 Spaces .050 at [1.27] 10 Spaces .050 at [1.27] .050 Solder Tail CL [1.27] (2 Plcs.) .150 [3.81] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 7 Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Through Hole Metal Holddowns .035 [0.89] (2 Plcs.) L 35° (2 Plcs.) Surface Mount .170±.020 [4.32±0.51] .300 [7.62] .610 [15.49] .078 [1.98] Ref. See Note. .075 [1.90] (2 Plcs.) .150 [3.81] 10 Spaces .050 at [1.27] 31 Spaces .050 at [1.27] L ±.010 W [±0.25] Typ. 48 Spaces at .050 [1.27] .060 [1.52] Typ. .150 [3.81] (2 Plcs.) .180 [4.57] .180 [4.57] Section L-L .100 2.54 Plating B Plating C .125 3.18 Surface Mount Plating C 145166-8 145169-8 Plating C — 145113-1 Contact Finish .17+.02 [4.318+.508] .003 [.076] .050 Solder [1.27] Tail CL (2 Plcs.) Part Numbers 5 Volt 3 Plastic 3 Metal Pylons Holddowns 145166-2 — 145166-4 145169-4 W (Post Length) .300 [7.62] Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 8 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors 32 Bit, 3.3 and 5 Volt Signaling Plastic Pylons .350 [8.89] 60 Dual Positions with 2 Plastic Pylons or 2 Metal Holddowns 3.340 [84.84] Material and Finish: Housing Y—High temperature thermoplastic 94V-0 rated, white Housing Z—Nylon 6/6, white Contacts—Phosphor bronze, plated as follows: Plating A—Duplex plated gold flash in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating B—Duplex plated .000015 [0.00038] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating C—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .035 [0.89] (2 Plcs.) L .300 [7.62] .610 [15.49] ±.010 W [±0.25] Typ. L .075 [1.90] (2 Plcs.) 10 Spaces .050 at [1.27] 48 Spaces at Metal Holddowns .050 [1.27] .035 [0.89] (2 Plcs.) L .150 [3.81] (2 Plcs.) .060 [1.52] Typ. See Note. Through Hole 35° (2 Plcs.) Product Specification 108-14034 Application Specification 114-26012 .078 [1.98] .003 Ref. [.076] Typ. .075 [1.90] (2 Plcs.) 10 Spaces .050 at [1.27] See Note. .050 48 Spaces at [1.27] .150 [3.81] (2 Plcs.) .050 Solder [1.27] Tail CL (2 Plcs.) .17+.02 [4.318+.508] .180 [4.57] .180 [4.57] Section L-L Plating A Plating B Plating C Plating A Plating B Part Numbers 2 Plastic 2 Metal Pylons Holddowns 145154-1 145167-1 145154-2 — 145154-4 145167-4 11299-1 — 11299-6 — Y Plating C 145154-8 — Y Plating C — 145098-1 W (Post Length) Housing Material .100 2.54 Y .118 3.00 Z .125 3.18 Surface Mount .060 [1.52] Typ. .300 [7.62] .300 [7.62] .610 [15.49] L Surface Mount .170±.020 [4.32±0.51] Technical Documents: ±.010 W [±0.25] .050 Solder Tail CL [1.27] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 7 .170±.020 [4.32±0.51] 35° (2 Plcs.) Contact Finish Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 9 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series PCI Card Edge Connectors 64 Bit, 3.3 Volt Signaling Plastic Pylons 92 Dual Positions with 3 Plastic Pylons or 3 Metal Holddowns .350 [8.89] 5.040 [128.02] Material and Finish: Housing—High temperature thermoplastic 94V-0 rated, white Contacts—Phosphor bronze, plated as follows: Plating B—Duplex plated .000015 [0.00038] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel Plating C—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .035 [0.89] (2 Plcs.) L 35° (2 Plcs.) .170±.020 [4.32±0.51] .300 [7.62] .610 [15.49] ±.010 W [±0.25] Typ. .075 [1.90] (2 Plcs.) 10 Spaces .050 at [1.27] 48 Spaces at 31 Spaces .050 at [1.27] .050 [1.27] .150 [3.81] (2 Plcs.) .060 [1.52] Typ. L See Note. .150 [3.81] .050 Solder Tail CL [1.27] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 7 Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Through Hole Metal Holddowns .035 [0.89] (2 Plcs.) L 35° (2 Plcs.) Surface Mount .170±.020 [4.32±0.51] .300 [7.62] See Note. L ±.010 W [±0.25] Typ. 10 Spaces .050 at [1.27] .075 [1.90] (2 Plcs.) .300 [7.62] .610 [15.49] .17+.02 [4.318+.508] .078 [1.98] .003 Ref. [.076] .150 [3.81] 31 Spaces .050 at [1.27] .050 48 Spaces at [1.27] .060 [1.52] Typ. .150 [3.81] (2 Plcs.) .050 Solder [1.27] Tail CL (2 Plcs.) .180 [4.57] .180 [4.57] Section L-L W (Post Length) Contact Finish .100 2.54 Plating B Plating C Part Numbers 3.3 Volt 3 Plastic 3 Metal Pylons Holddowns — 145168-2 1-145165-4 145168-4 .125 3.18 Surface Mount Plating C 1-145165-8 — Plating C — 145246-1 Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls. Notes: 2. Other connector sizes can be made available, consult Tyco Electronics. 10 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Product Facts ■ ■ ■ ■ ■ ■ ■ High density .050 [1.27] centerline spacing of contacts Easy mating of high-circuit count daughter boards Compatible with infrared reflow (IR) soldering techniques Polarizing web for positive board-to-connector registration Choice of plastic pylons or metal holddowns Recognized under the Component Program of Underwriter Laboratories Inc. File No. E28476 Certified by Canadian Standards Association, ® File No. LR 7189 Performance Specifications: Contact Current Rating* —1 ampere Termination Resistance — 20 milliohms max. (initial) 30 milliohms max. (final) Dielectric Withstanding Voltage — 500 VAC min. Insulation Resistance — 1000 megohms min. Mating Force — .5 oz. [0.14 N] per contact pair Unmating Force — 1 oz. [0.3 N] per contact pair Durability (Tested to) — 100 mating cycles Application Temperature — +215°C for 120 seconds max. Temperature Range — –55°C to +85°C *Consult Tyco Electronicsengineering when paralleling contacts for power applications. The need to conserve space and pack more function into a given area has demanded that .050 [1.27] centerline spacing become a reality. AMP Standard Edge .050 Series connectors are the ideal vehicle for mother/daughter board applications requiring this real estate. These rugged connectors have two rows of contacts on .050 [1.27] centerlines. Polarizing webs provide positive board-to-connector registration, while insertion force allows even high circuit-count daughter boards to mate easily. The connectors accept .054 to .070 [1.37 to 1.78] thick daughter boards and feature an overstress protected contact design. AMP Standard Edge .050 Series connectors are ideal for fast automated robotic assembly with registration features and dimensional tolerancing for more accurate pickup and placement, and are packaged in roboticscompatible trays. Plastic guide posts or metal holddowns align the connector with the mother board and retain it for soldering. To make circuit routing easy, connector solder posts are arranged in a four-row .100 [2.54] staggered grid. Hightemperature tolerant materials promote that these connectors withstand infrared reflow (IR) soldering, while standoffs ease flux cleaning. High Density for DataBus Applications 11 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Configuration; 1 Key—2 Plastic Pylons .350 [8.89] Material and Finish: Housing—High temperature thermoplastic, brown Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel C .035 [0.89] (2 Plcs.) L .170±.020 [4.32±0.51] 35° (2 Plcs.) .300 [7.62] .610 [15.49] Related Product Data: Performance Specifications— page 11 Technical Documents: W (Post Length) Product Specification 108-14034 Application Specification 114-26012 .075 [1.90] (2 Plcs.) .012 [0.30] Typ. .060 Typ. [1.52] L B Spaces .050 at [1.27] A Spaces .050 at [1.27] .150 [3.81] (2 Plcs.) Section L-L .016 Typ. [0.41] No. of Dual Positions A Dimensions B 23 10 11 30 10 18 1.490 37.85 1.840 46.74 40 10 28 2.340 59.44 C 45 10 33 2.590 65.79 56 10 44 3.140 79.76 41 4.340 110.24 80 91 37 41 48 .050 [1.27] (2 Plcs.) 4.890 124.21 W (Post Length) .100 2.54 .100 2.54 .100 2.54 .140 3.56 .100 2.54 .100 2.54 .140 3.56 .100 2.54 .100 2.54 .140 3.56 PC Board Hole Layout Connector Part Numbers A 0-650090-7 B 0-650090-6 B 0-650090-3 B 0-650181-2 A 0-650090-2 B 10-650090-11 B 0-650181-1 C 0-650090-9 A 10-650092-12 A 0-650092-2 1 Connector used for VLLocal Bus and MCA Bus applications. used for MCA Bus applications. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. .125 [3.18] post length is available, consult Tyco Electronics. 2 Connector 12 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Configuration; 1 Key—2 Plastic Pylons .350 [8.89] Material and Finish: Housing—High temperature thermoplastic, brown Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel D .035 [0.89] (2 Plcs.) L .170±.020 [4.32±0.51] 35° (2 Plcs.) .300 [7.62] .610 [15.49] Related Product Data: Performance Specifications— page 11 Technical Documents: W (Post Length) Product Specification 108-14034 .075 [1.90] (2 Plcs.) L B Spaces .050 at [1.27] A Spaces .050 at [1.27] C Spaces .050 at [1.27] .060 Typ. [1.52] .012 [0.30] Typ. .150 [3.81] (2 Plcs.) .150 [3.81] Application Specification 114-26012 .050 [1.27] (2 Plcs.) Section L-L .016 Typ. [0.41] .096 Dia. Max. [2.44] No. of Dual Positions A Dimensions B C 66 10 44 9 D 3.740 95.00 W (Post Length) .100 2.54 .140 3.56 PC Board Hole Layout Connector Part Numbers A 1650091-1* A 650091-2 *Connectors used for MCA Bus applications. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. .125 [3.18] post length is available, consult Tyco Electronics. 13 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type Board-to-Board) Standard Edge .050 Series Connectors Configuration; 1 Key/1 Web —3 Metal Holddowns .350 [8.89] 120 Dual Positions 6.440 [163.58] Material and Finish: .035 [0.89] (2 Plcs.) L Housing—High temperature thermoplastic, brown Holddowns—Brass, plated .000150 [0.00381] min. tin-lead over .000050 [0.00127] min. nickel Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel 35° (2 Plcs.) .300 [7.62] .610 [15.49] .170±.020 [4.32±0.51] W (Post Length) .150 [3.81] 63 Spaces .050 at [1.27] 44Spaces .050 at [1.27] 10Spaces .050 at [1.27] .180 [4.57] .060 Typ. [1.52] L .075 [1.90] (2 Plcs.) .150 [3.81] (2 Plcs.) .050 Solder Tail C L [1.27] (2 Plcs.) Section L-L Related Product Data: Performance Specifications— page 11 Technical Documents: No. of Dual Positions Product Specification 104-14034 Application Specification 114-26012 W (Post Length) .140 3.56 120 Connector Part Numbers 145031-3 Note: Other connector sizes can be made available, consult Tyco Electronics. Configuration; End Key .096 [2.44] Dia. Max. Material and Finish: Housing—High temperature thermoplastic, brown Contacts—Phosphor bronze, duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on solder tails, with entire contact underplated .000050 [0.00127] min. nickel .016 Typ. [0.41] .350 [8.89] .099 [2.52] Max. B .035 [0.89] L 35° Related Product Data: .170±.020 [4.32±0.51] .300 [7.62] Performance Specifications— page 11 .610 [15.49] Technical Documents: Product Specification 108-14034 Application Specification 114-26012 Post Length .012 Typ. [0.30] .050 [1.27] (2 Plcs.) .060 Typ. [1.52] L .075 [1.90] .150 [3.81] (2 Plcs.) A Spaces .050 at [1.27] Section L-L No. of Dual Positions A B 25 24 1.480 37.59 Dimensions C 1.350 34.29 D 1.310 33.27 Post Length .100 2.54 Connector Part Numbers 650719-1 Note: Other connector sizes can be made available, consult Tyco Electronics. 14 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors Product Facts ■ ■ ■ ■ ■ ■ ■ ■ Maximum number of dual positions .100 [2.54] Centerlines-70, .125 [3.18] Centerlines-50, .150 [3.81] Centerlines-31 Selective gold plating of contacts for high performance at low cost .025 [0.64] square solid posts meet standard wraptype specifications For flow solder applications Glass-filled polyester housing is 94V-0 rated Accepts double sided PC boards, .054-.070 [1.27-1.78] thick Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association, File No. LR 7189 Performance Specifications Contact Rating*: 3 amperes continuous (UL and CSA) Contact Resistance: 10 milliohms max. Operating Temperature: –55°C to +85°C Voltage Rating (Sea Level): .100 [2.54] centerline—1000 VAC (test) .125 [3.18] centerline—1500 VAC (test) .150 [3.81] centerline—1500 VAC (test) Insulation Resistance: 5000 megohms min., after exposure to humidity Vibration Tolerance: 10 to 500 hertz Contact Engagement Force: 12 oz [3.3 N] average per pair with .062 [1.57] PC board Contact Separation Force: 2 oz [0.6 N] average per pair with .062 [1.57] PC board AMP Standard Edge II Connectors provide high reliability and economy in packages compatible with industry standards for double sided printed circuit boards. Tyco Electronics offers Standard Edge II Connectors with or without mounting ears, for rack mounting and soldering. Contacts are arranged on .100 [2.54] centers, .125 [3.18] centers, .150 [3.81] centers, .200 [5.08] row-to-row; and .250 [6.35] row-to-row. Right-angle connectors are also available with contacts arranged on .100 [2.54] centers, .150 [3.81] row-to-row or .200 [5.08] row-to-row. Card extenders with contacts on .100 [2.54] and .125 [3.18] centers also are available. Precision formed phosphor bronze contacts are selectively gold plated. Phosphor bronze has excellent strength characteristics which help the connector absorb load deflection movement of a PC board while maintaining sufficient contact force for good electrical connection. Bifurcated cantilever beam contacts provide redundant contact. Humidity Tolerance: 90%-95% for 96 hours *Consult Tyco Electronics engineering when paralleling contacts for power applications. 15 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors Styles .100 [2.54] Centerline Right-Angle Posts with Low and No Mounting Ears Page 23 .100 [2.54] and .125 [3.18] Centerline Solder Posts without Mounting Ears Pages 17 and 18 .100 [2.54] and .125 [3.18] Centerline Solder Posts with Low and Mid-High Mounting Ears Page 20 .100 [2.54] and .125 [3.18] Centerline Wrap-Type Posts with Mid-High Mounting Ears Page 21 .100 [2.54] and .125 [3.18] Centerline Card Extenders Page 22 .100 [2.54] Centerline Solder Posts with Board Retention Feature, without Mounting Ears Page 24 .150 [3.81] Centerline Solder Posts (with Board Retention Feature), without Mounting Ears Page 19 16 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Centerline, Vertical Solder Posts, Without Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .064 [1.63] Sq. x .130 [3.30] Dp. Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, duplex plated as follows: Plating A—.000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated Plating B—.000015 [0.00038] gold in contact area, tin on posts, with entire contact nickel underplated Plating C—Gold flash in contact area, tin on posts, with entire contact nickel underplated .100 [2.54] .368 [9.35] D C** .141/.153 [3.58/3.88] Retention Feature (Open End Card Slot) Accepts .054/.070 [1.37/1.77] PC Board A .295 [7.49] .550 [13.97] .610 [15.49] .100 Typ. [2.54] .060 [1.52] B .155 [3.94] Post Length .191 [4.85] Technical Documents: Product Specification 108-9039 No. of Dual Positions 3 Intercontact Keying Plug 6 Material: 10 Natural color polyester 12 15 17 18 20 Part Number 650025-2 (.100 [2.54] Centerline) 22 25 28 30 31 36 40 50 Dimensions B C** A .560 14.22 .860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 1.960 49.78 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.860 98.04 4.260 108.20 5.260 133.60 .450 11.43 .750 19.05 1.150 29.21 1.350 34.29 1.650 41.91 1.850 46.99 1.950 49.53 2.150 54.61 2.350 59.69 2.650 67.31 2.950 74.93 3.150 80.01 3.250 82.55 3.750 95.25 4.150 105.41 5.150 130.81 Open End .700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.700 93.98 4.100 104.14 5.100 129.54 D .200 5.08 .500 12.70 .900 22.86 1.100 27.94 1.400 35.56 1.600 40.64 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.500 88.90 3.900 99.06 4.900 124.46 Post Length* Plating A Part Numbers Plating B Plating C .125 10-650263-1 1 — — .125 .187 .125 .187 7-530843-5 7-530843-6 5-530843-0 4-530843-9 — — — — .125 0-530843-1 — — .125 0-530843-2 — — .125 5-530843-3 — — .125 0-530843-3 2-530843-7 1176137-11 .125 5-530843-4 — — .125 0-530843-4 — — .125 0-530843-5 — — .125 0-530843-6 — — .125 .187 0-530843-7 1-530843-8 — — .125 6-530843-5 7-530843-0 — .125 0-530843-8 — — .187 2-530843-0 — — .125 1-530843-1 — — **Metric equivalent for post lengths are .125 = 3.18; .187 = 4.75. **C dimension is card slot length. 1 Connectors with Retention Feature. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 17 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .125 [3.18] Centerline, Vertical Solder Posts, Without Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .064 [1.63] Sq. x .130 [3.30] Dp. Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .125 [3.18] .368 [9.35] D C** Retention Feature Accepts .054/.070 [1.37/1.77] PC Board A Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .191/.203 [4.85/5.16] .295 [7.49] .550 [13.97] .610 [15.49] .155 [3.94] .125 [3.18] Technical Documents: (pages 186, 187): Post Length .241 [6.11] .060 [1.52] B Product Specification 108-9039 Intercontact Keying Plug Material: Natural color polyester No. of Dual Positions 6 14 18 22 28 Part No. 650025-1 (.125 [3.18] Centerline) 30 36 40 43 50 Dimensions C** A B 1.035 26.29 2.035 51.69 2.535 64.39 3.035 77.09 3.785 96.14 4.035 102.49 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 .875 22.22 1.875 47.62 2.375 60.33 2.875 73.03 3.625 92.08 3.875 98.42 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 .875 22.22 1.875 47.62 2.375 60.33 2.875 73.03 3.625 92.08 3.875 98.42 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 D .625 15.88 1.625 41.28 2.125 53.98 2.625 66.68 3.375 85.73 3.625 92.08 4.375 111.13 4.875 123.82 5.250 133.35 6.125 155.58 Post Length* .125 Part Numbers 650207-11 .187 5-530844-8 .187 1-530844-5 .187 1-530844-6 .187 1-530844-7 .187 1-530844-8 .187 1-530844-9 .187 2-530844-0 .125 1-530844-0 .125 .187 1-530844-1 2-530844-2 **Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. Note: Other connector sizes can be made available, consult Tyco Electronics. 18 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .150 [3.81] Centerline, Vertical Solder Posts, Retention Feature, Without Mounting Ears Inter-Contact Keying Slot Card Slot Accepts .054-.070 [1.37-1.78] Printed Circuit Board B ±.010 [±0.25] +.005 .432 -.010 [10.97] +0.13 -0.25 Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .305 [9.27] .045 [1.14] Contact Area .015 [0.38] .080 [.203] Lead in .200±.020 Area [5.08±0.51] .016 [0.41] .020 [0.51] .035±.020 [3.430±0.51] .200 [5.08] Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .600 [15.21] .024 [0.61] .020 [0.51] No. of Dual Positions 12 19 28 31 0.143–.161 [3.63–4.03] .025 [0.63] Spaces at .150 = Dim A Ref. [3.81] Dimensions A B Retention Location Post Length* Part Numbers 1.650 41.91 2.700 68.58 4.050 102.87 4.500 114.30 1.920 48.77 2.970 75.44 4.320 109.73 4.770 121.16 7-10, 15-18 7-10, 29-32 7-10, 25-32,47-50 7-10, 27-34,53-56 .135 1-650728-2 .135 1-650728-9 .135 2-650728-9 .135 3-650728-1 **Metric equivalent for post length is .135 = [3.43] **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 19 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .100 [2.54] and .125 [3.18] Centerline, Vertical Solder Posts, Low and Mid-High Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot G Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .368 [9.35] H .150 [3.81] .300 .128 Dia. [7.62] [3.25] D C** Accepts .054/.070 [1.37/1.77] PC Board F .360 [9.14] A .550 [13.97] .610 [15.49] .155 [3.94] Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .295 [7.49] .250 [6.35] .060 [1.52] B E J Post Length .180 [4.57] Low Mounting Ears Technical Documents: (pages 186, 187): Product Specification 108-9039 .250 [6.35] Intercontact Keying Plugs Material: Natural color polyester Retention Feature Mid-High Mounting Ears .100 [2.54] Centerline No. of Dual Positions 15 18 25 30 36 Part No. 650025-2 (.100 [2.54] Centerline) .141/.153 [3.58/3.88] 50 A B C** D Dimensions E F G H J 1.760 44.70 2.060 52.32 2.760 70.10 3.260 82.80 3.860 98.04 1.650 41.91 1.950 49.53 2.650 67.31 3.160 80.01 3.750 95.25 1.600 40.64 1.900 48.26 2.600 66.04 3.100 78.74 3.700 93.98 1.400 35.56 1.700 43.18 2.400 60.96 2.900 73.66 3.500 88.90 2.385 67.18 2.645 67.18 3.345 84.96 3.845 97.66 4.445 112.90 2.075 52.71 2.375 60.32 3.075 78.11 3.575 90.81 4.175 106.21 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .100 2.54 .191 4.85 .191 4.85 .191 4.85 .191 4.85 .191 4.85 .191 4.85 .141-.153 3.58-3.88 5.260 133.60 5.150 130.81 5.100 129.54 4.900 124.46 5.845 148.46 5.575 141.60 .100 2.54 .100 2.54 Post Length* Part Numbers .125 0-530841-2 .125 0-530841-3 .125 .187 0-530841-5 1-530841-6 .187 1-530841-8 .125 0-530841-8 .125 .187 1-530841-1 2-530841-2 .125 0-650718-11,2 **Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. 2Connector with Mid-High Mounting Ears. Note: Other connector sizes can be made available, consult Tyco Electronics. .125 [3.18] Centerline No. of Dual Positions A B C** D Dimensions E F G H J 6 1.035 26.29 .875 22.22 .875 22.22 .625 15.88 1.555 39.50 1.295 32.89 .125 3.18 .125 3.18 28 3.785 96.14 3.505 89.03 3.625 92.08 3.375 85.73 4.305 109.35 4.045 102.74 .125 3.18 .125 3.18 .241 6.11 .241 6.11 .241 6.11 6.535 165.99 6.255 158.88 6.375 161.93 6.125 155.58 7.055 179.20 6.795 172.59 .125 3.18 .125 3.18 50 Part No. 650025-1 (.125 [3.18] Centerline) 20 Catalog 1654080 Issued 7-03 www.tycoelectronics.com .241 6.11 Post Length* Part Numbers .125 1-531341-3 .187 1-530842-7 .187 23-531341-02 .125 1-530842-1 **Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75] **C dimension is card slot length. 1Connector with Retention Feature. 2Connector with Mid-High Mounting Ears. Note: Other connector sizes can be made available, consult Tyco Electronics. Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .100 [2.54] and .125 [3.18] Centerline, Vertical WrapType Posts, Mid-High Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. .064 [1.63] Sq. x .130 [3.30] Dp. .150 [3.81] Intercontact Key Slot Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .128 Dia. [3.25] G .368 [9.35] D H C F .180 [4.57] A Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 Special Application—page 96 .300 [7.62] Accepts .054/.070 [1.37/1.77] PC Board .295 [7.49] .550 [13.97] .250 .610 [15.49] [6.35] .155 [3.94] .060 [1.52] Technical Documents: B (pages 186, 187): Post Length E J Product Specification 108-9039 Intercontact Keying Plugs Material: Natural color polyester .100 [2.54] Centerline No. of Dual Positions A B C** D Dimensions E F G H 3.260 3.150 3.100 2.900 3.845 3.575 .100 .100 82.80 80.01 78.74 73.66 97.41 90.80 2.54 2.54 3.860 3.750 3.700 3.500 4.435 4.175 .100 .100 36 98.04 95.25 93.98 88.90 112.65 106.04 2.54 2.54 4.260 4.150 4.100 3.900 4.845 4.575 .100 .100 40 108.20 105.41 104.14 99.06 123.06 116.21 2.54 2.54 **Metric equivalent for post length is .570 = [14.48]. **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 30 Part No. 650025-2 (.100 [2.54] Centerline) Post Length* Part Numbers .570 3-530396-3 .570 3-530396-4 .570 3-530396-4 J Post Length* Part Numbers .250 6.35 .570 4-530825-5 J .200 5.08 .200 5.08 .200 5.08 .125 [3.18] Centerline No. of Dual Positions A B C** D Dimensions E F G H 3.035 2.755 2.875 2.625 3.555 3.295 .125 .125 77.09 69.98 73.02 66.67 90.30 83.69 3.18 3.18 **Metric equivalent for post length is .570 = [14.48]. **C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 22 Part No. 650025-1 (.125 [3.18] Centerline) 21 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) .100 [2.54] and .125 [3.18] Centerlines, Card Extender Contacts Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated .064 [1.63] Sq. x .130 [3.30] Dp. .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .128 Dia. [3.25] .368 [9.35] D H .300 [7.62] .150 [3.81] G .180 [4.67] C Related Product Data: Performance Specifications— page 15 PC Board Hole Layout—page 26 PC Board Edge Pattern—page 27 E F Accepts .054/.070 [1.37/1.77] PC Board .180 [4.57] A Technical Documents: .295 [7.49] (pages 186, 187): Product Specification 108-9039 .550 [13.97] .610 [15.49] .155 [3.94] Mounting Block Material: .060 [1.52] Natural color nylon .062 Dia. [1.57] Roll Pin .250 [6.35] .340 [8.63] B Fits .054/.070 [1.37/1.77] PC Board Card Extender Connector Housing Ref. #5 Self Tapping Screws .100 [2.54] Centerline No. of Dual Positions Mounting Block .062 [1.57] PC Board Ref. Kit Part No.531250-4 Each kit includes 2 mounting blocks, 2 self tapping screws, #5 x .437 [11.10] and 2 roll pins, .075 x .250 [1.57 x 6.35] A B C** Dimensions D E F 5.260 5.160 5.100 4.900 5.845 5.575 133.60 130.81 129.54 124.46 148.46 141.60 *C dimension is card slot length. 1No mounting ears. Note: Other connector sizes can be made available, consult Tyco Electronics. 50 G H .100 2.54 .100 2.54 G H .125 3.18 .125 3.18 Part Numbers 530826-3 Intercontact Keying Plugs Material: Natural color polyester .125 [3.18] Centerline No. of Dual Positions A B C** Dimensions D E F 4.785 4.505 4.625 4.375 5.035 5.045 121.54 114.43 117.48 111.13 134.75 128.14 *C dimension is card slot length. Note: Other connector sizes can be made available, consult Tyco Electronics. 36 Part No. 650025-1 (.125 [3.18] Centerline) Part Numbers 530384-2 Part Number 650025-2 (.100 [2.54] Centerline) 22 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Right-Angle Solder Posts, with Low and No Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Accepts .054/.070 [1.37/1.77] PC Board .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .295 [7.49] Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, duplex plated as follows: Plating A—.000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated Plating B—.000015 [0.00038] gold in contact area, tin on posts, with entire contact nickel underplated .368 [9.35] .100 [2.54] .100 [2.54] .155 [3.94] .300 [7.62] G D C Post Length With Board Locks E Accepts .054/.070 [1.37/1.77] PC Board F Related Product Data: A Performance Specifications— page 15 .295 [7.49] .550 [13.97] .610 [15.49] G Technical Documents: Product Specification 108-9039 .250 [6.25] .128 Dia. [3.25] .155 [3.94] .080 [1.82] B Post Length Low Mounting Ears Intercontact Keying Plug Material: Natural color polyester Low Mounting Ears No. of Dual Positions 12 18 20 Part Number 650025-2 (.100 [2.54] Centerline) A B C* 1.460 37.08 2.060 52.32 2.260 57.40 1.350 34.29 1.950 49.53 2.150 54.61 1.300 33.02 1.900 48.26 2.100 53.34 Dimensions D E 1.100 27.94 1.700 43.18 1.900 48.26 2.045 51.94 2.645 67.18 2.845 72.30 F G1 1.775 45.08 2.375 60.32 2.575 65.40 x.100x .150 x.100x .150 x.100x .150 Post Length2 Part Numbers (Plating A) .090 3145089-13 .090 645384-1 .090 645384-3 *C dimension is card slot length. 1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08]. 2 Metric equivalent for post length is .090 = [2.27]. 3 Connector with Board Locks. Note: Other connector sizes can be made available, consult Tyco Electronics. No Mounting Ears No. of Dual Positions 15 17 25 31 32 19 A B 1.760 44.70 1.960 49.78 2.760 70.10 3.360 85.34 3.460 87.88 2.160 54.86 1.650 41.91 1.850 46.99 2.350 67.61 3.250 82.55 3.350 85.09 2.750 69.85 Dimensions C* D 1.600 40.64 1.800 45.72 2.600 66.04 3.200 81.28 3.300 83.82 2.700 68.58 1.400 35.56 1.600 40.64 2.400 60.96 3.000 76.20 3.100 78.74 1.800 45.72 G1 .100x .150 .100x .200 .100x .150 .100x .150 .100x .150 .100x .150 Post Length2 Part Numbers Plating A Plating B .090 650118-1 — .090 650187-1 — .090 — 532600-2 .090 — 532600-4 .090 — 532600-5 .090 — 532600-6 *C dimension is card slot length. 1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08]. 2 Metric equivalent for post length is .090 = [2.27]. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 23 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Centerline Vertical Solder Posts, Retention Feature, Without Mounting Ears .064 [1.63] Sq. x .130 [3.30] Dp. Intercontact Key Slot .064 [1.63] Sq. x .130 [3.30] Dp. Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, duplex plated as follows: Plating A—.000030 [0.00076] gold in contact area, tin on posts, with entire contact nickel underplated Plating B—.000015 [0.00038] gold in contact area, tin on posts, with entire contact nickel underplated Plating C—Gold flash in contact area, tin on posts, with entire contact nickel underplated .368 [9.35] .100 [2.54] D C Accepts .054/.070 [1.37/1.77] PC Board A .295 [7.49] .550 [13.97] .610 [15.49] .155 [3.94] Technical Documents: Product Specification 108-9039 .060 [1.52] Post Length .191 [4.85] .100 Typ. [2.54] B Intercontact Keying Plug Material: Natural color polyester .141/.153 [3.58/3.88] Retention Feature Part Number 650025-2 (.100 [2.54] Centerline) No. of Dual Positions 18 31 50 60 A 2.060 52.32 3.360 85.34 5.260 133.60 6.260 159.00 Dimensions B C** 1.950 49.53 3.250 82.55 5.150 130.81 6.150 156.21 1.900 48.26 3.200 81.28 5.100 129.54 6.100 154.94 D 1.700 43.18 3.000 76.20 4.900 124.46 5.900 149.86 Post Length* Retention Feature PartNumbers Plating A .125 3-6, 31-34 1-645235-4 .125 3-6, 29-32 or 31-34, 57-60 3-6, 49-52, 95-98 3-6, 55-58, 63-66, 115-118 1-645235-1 .125 .125 1-645235-3 1-645235-8 **Metric equivalent for post length is .125 = [3.18]. **C dimension is card slot length. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 24 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Card Edge Connectors .100 [2.54] Centerline, Special 18/31 Dual Combination Connector, Vertical Solder Posts, Without Mounting Ears .200 [5.08] .100 [2.54] .368 [9.35] .100 [2.54] Material and Finish: 1.900 [48.26] .141/.153 [3.58/3.88] 3.200 [81.28] Housing—Black glass-filled polyester, 94V-0 rated, except where noted Contacts—Phosphor bronze, plated with .000030 [0.00076] gold in contact area (except where noted), tin on posts, with entire contact nickel underplated Retention Feature 5.460 [138.68] Accepts .054/.070 [1.37/1.77] PC Board .550 [13.97] .610 [15.49] Technical Documents: .295 [7.49] Product Specification 108-9039 .400 [10.16] .060 [1.52] A A Solder Posts 5.350 [135.89] Intercontact Keying Plug .191 [4.85] Material: Natural color polyester Part Number 650025-2 (.100 [2.54] Centerline) No. of Dual Positions Post Type 52 Solder Posts 52 Solder Posts 52 Solder Posts 52 Solder Posts 52 Solder Posts Dimension Retention A Feature .125 3.18 .125 3.18 .125 3.18 .125 3.18 .187 4.75 Part Numbers 3-6, 41, 42, 51, 52, 93-96 1536128-11 645169-2 None 645169-3 3-14, 41, 42, 51, 52, 85-96 5, 6, 31, 32, 41, 42, 93, 94 2176139-12 2 None 650616-1 645169-4 Housing material is high temperature glass-filled polyester, gray. Contact area is gold flash. Notes: 1. Card slot length is 5.300 [134.62]. 2. Other connector sizes can be made available, consult Tyco Electronics. 3. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics. 1 2 25 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) Recommended PC Board Hole Layouts Vertical Post Connectors D B ±.003 C [±0.08] Dia. .128 Dia. [3.25] A F A B Dimensions C .100 2.54 .150 3.81 .125 3.18 .100/.125 2.54/3.18 .100 2.54 .125 3.18 .200 5.08 .200 5.08 .250 6.35 .200/.250 5.08/6.35 .200 5.08 .250 6.35 .040 1.02 .040 1.02 .040 1.02 .040 1.02 .042 1.07 .042 1.07 Connector Type Solder Post/Retention Solder Post/Retention Solder Post, Mounting Ears Solder Post, W/O Mounting Ears Wrap-Type Post Wrap-Type Post Notes: 1. 2. 3. 4. 5. D F See Note 1 See Note 2 See Note 4 See Note 2 See Note 3 See Note 3 See Note 4 See Note 2 See Note 5 See Note 5 See Note 5 See Note 5 Refer to page 24 for D Dimensions and Dual Positions. No mounting ears. Dimensions do not apply. Refer to page 20 for D and F Dimensions and Dual Positions. Refer to pages 18 and 19 for D Dimensions and Dual Positions. Refer to page 21 for D and F Dimensions and Dual Positions. Right-Angle Post Connectors F D B .128 Dia. [3.25] ±.003 C [±0.08] Dia. A G .337 [8.56] Connector Type Right-Angle Posts, Mounting Ears Right-Angle Posts, No Mounting Ears A .100 2.54 .100 2.54 B .150 3.81 .150 or .200 3.81 or 5.08 C .042 1.07 .042 1.07 Dimensions D F See Note 1 See Note 1 G .137 3.48 See Note 2 See Note 3 See Note 3 Notes: 1. Refer to page 23 for D and F Dimensions and Dual Positions. 2. Refer to page 23 for D Dimensions and Dual Positions. 3. No Mounting Ears, Dimensions do not apply. 26 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Standard Edge II Connectors (Continued) Recommended PC Board Edge Pattern PC Board Edge Pattern for .100 [2.54] and .125 [3.18] Centerline .050 [1.27] Intercontact Key Slot Datum CL .015 x 45° [0.38] Chamfer .295 Min. [7.49] Engagement Depth .310 Min. [7.87] B .054/.070 [1.37/1.77] ±.005 A D [±0.13] ±.005 C [±0.13] No. of Dual Positions 3 6 10 12 13 .100 [2.54] Centerline A = .093 [2.36] B = .050 [1.27] C D .386 .200 9.80 5.08 .686 .500 17.42 12.70 1.086 .900 27.58 22.86 1.286 1.100 32.66 27.94 1.386 1.200 35.20 30.48 .125 [3.18] Centerline A = .118 [3.00] B = .075 [1.90] C D — — .861 21.87 1.361 34.57 .625 15.88 1.125 28.58 — — — — 1.625 41.28 — 14 — — 1.861 47.27 15 1.586 40.28 1.786 45.36 1.886 47.90 2.286 58.06 2.586 65.68 2.886 73.30 3.086 78.38 3.186 80.92 3.586 91.08 3.686 93.62 4.086 103.78 4.386 111.40 5.086 129.18 6.086 154.58 7.086 179.98 1.400 35.56 1.600 40.64 1.700 43.18 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 6.900 175.26 — 17 18 22 25 28 30 31 35 36 40 43 50 60 70 — — 2.361 59.97 2.861 72.67 2.125 53.98 2.625 66.68 — — 3.611 91.72 3.861 98.07 3.986 101.24 3.375 85.73 3.625 92.08 3.750 95.25 — — 4.611 117.12 5.111 129.82 5.486 139.34 6.361 161.57 4.375 111.13 4.875 123.82 5.250 133.35 6.125 155.58 — — — — 27 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Card Edge Connectors Product Facts Double readout Card Edge connectors use dip solder contacts ■ Large lead-in chamfers allow easy PC board installation ■ Insulator standoffs prevent solder from wicking ■ Various lengths for custom applications ■ Contact option, single or dual row ■ Description Design Advantages The Cantilever Beam Series products from Tyco Electronics are double readout cardedge connectors, using dip solder contacts. Tooled for flexible manufacturing, these Card Edge connectors are readily available in a broad assortment of sizes and mounting styles. Our connectors meet industry standards. • Circuit Integrity: Robust cantilever contacts are designed to promote optimal normal forces at the lowest possible cost. Our uniquely contoured contact mating surface gives you constant engagement, even when subjected to continuous vibration. • Ease of Assembly: Generous lead-in chamfers let your P.C. board slide easily into the connector. Insulator standoffs are provided to facilitate cleaning and prevent solder from wicking. Availability, flexibility, performance and very low cost make the Cantilever Series from Tyco Electronics the clear choice in Card Edge connectors. Cantilever Beam The Cantilever Beam Card Edge connector comes with standard high temperature plastic insulators. Contacts are available in a variety of lengths to accommodate various custom applications. Standoffs allow for cleaning and draining and are available as an option on most insulator bodies. Cantilever Beam Card Edge offers a variety of card slot depths. A full scoop option is available for ease of installation in applications where visibility is limited. Contact options vary in this series from dual row standard contacts, single row options and press-fit. 28 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .020±.010Contact Gap [.51±.25] .145 [3.68] Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .300 Card Slot Depth [7.62] .13 [3.30] .200 [5.08] .400 [10.16] 1.700 [43.18] 3.000 [76.20] .100 [2.54] .200 [5.08] .040±.003 Dia. [1.02±.080] Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms 5.460 [138.68] 5.300 [134.62] 1.900 [48.26] 3.70 [9.40] Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 .100 Ref. [2.54] 3.200 [81.28] .200 Ref. [5.08] 5.100 [129.54] .300 [7.62] .610 [15.49] .06 [1.52] .06 [1.52] .100 Typ. [2.54] Ordering Information Acquired Part Number C8D52DS29C1M191 – Insulator with molded-in polarizing key with card guide chamber. The card slot lengths are 1.900 [48.26] and 3.200 [81.28]. Includes retention tails for .062 [1.57] PCB to hold connectors securely during handling. C8D52DS29C1M195 – Same as above. No retention tails. 29 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline Dip Solder Tails, .300 [7.62] Card Slot Depth Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ D E Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .020±.010Contact Gap [.51±.25] .145 [3.68] .370 [9.40] .300 Card Slot Depth [7.62] J .100 Typ. [2.54] .200 [5.08] B A C .250 [6.35] .610 [15.49] Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .060 .180 [1.52] [4.57] .020 Typ. Dia. [0.51] E Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .040±.003 [1.02±.08] Dia. .128 [3.25] Dia. Dim E Related Product Data: Daughter Card Edge Pattern— page 57 .200 [5.08] .100 [2.54] Mounting Styles .125 [3.18] Dia. #4-40 .125 [3.18] Dia. .250 [6.35] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole .250 [6.35] Flush Mounting Ear 4-40 Threaded Insert 30 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Mounting Ear Options Dimensions A B C D E Tail Length .130" [3.30] (DIM “J”) 1.435 1.175 6 36.45 29.85 10 1.835 1.575 46.61 40.01 2 . 0 3 5 1 .775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3 . 0 3 5 2 .775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3 . 9 3 5 3 .675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 5.835 5.575 50 148.21 141.61 6.835 6.575 60 173.61 167.01 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 Tail Length .160" [4.06] (DIM “J”) 1.435 1.175 6 36.45 29.85 1.835 1.575 10 46.61 40.01 2 . 0 3 5 1 .775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3 . 0 3 5 2 .775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3 . 9 3 5 3 .675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C8D06DS29A1 C8D06DS29B1 C8D06DS29C1 C8D06DS29D1 C8D06DS29E1 C8D10DS29A1 C8D10DS29B1 C8D10DS29C1 C8D10DS29D1 C8D10DS29E1 C8D12DS29A1 C8D12DS29B1 C8D12DS29C1 C8D12DS29D1 C8D12DS29E1 C8D15DS29A1 C8D15DS29B1 C8D15DS29C1 C8D15DS29D1 C8D15DS29E1 C8D18DS29A1 C8D18DS29B1 C8D18DS29C1 C8D18DS29D1 C8D18DS29E1 C8D20DS29A1 C8D20DS29B1 C8D20DS29C1 C8D20DS29D1 C8D20DS29E1 C8D22DS29A1 C8D22DS29B1 C8D22DS29C1 C8D22DS29D1 C8D22DS29E1 C8D25DS29A1 C8D25DS29B1 C8D25DS29C1 C8D25DS29D1 C8D25DS29E1 C8D28DS29A1 C8D28DS29B1 C8D28DS29C1 C8D28DS29D1 C8D28DS29E1 C8D30DS29A1 C8D30DS29B1 C8D30DS29C1 C8D30DS29D1 C8D30DS29E1 C8D31DS29A1 C8D31DS29B1 C8D31DS29C1 C8D31DS29D1 C8D31DS29E1 C8D35DS29A1 C8D35DS29B1 C8D35DS29C1 C8D35DS29D1 C8D35DS29E1 C8D36DS29A1 C8D36DS29B1 C8D36DS29C1 C8D36DS29D1 C8D36DS29E1 C8D40DS29A1 C8D40DS29B1 C8D40DS29C1 C8D40DS29D1 C8D40DS29E1 C8D43DS29A1 C8D43DS29B1 C8D43DS29C1 C8D43DS29D1 C8D43DS29E1 C8D50DS29A1 C8D50DS29B1 C8D50DS29C1 C8D50DS29D1 C8D50DS29E1 C8D60DS29A1 C8D60DS29B1 C8D60DS29C1 C8D60DS29D1 C8D60DS29E1 C8D06DS29A2 C8D06DS29B2 C8D06DS29C2 C8D06DS29D2 C8D06DS29E2 C8D10DS29A2 C8D10DS29B2 C8D10DS29C2 C8D10DS29D2 C8D10DS29E2 C8D12DS29A2 C8D12DS29B2 C8D12DS29C2 C8D12DS29D2 C8D12DS29E2 C8D15DS29A2 C8D15DS29B2 C8D15DS29C2 C8D15DS29D2 C8D15DS29E2 C8D18DS29A2 C8D18DS29B2 C8D18DS29C2 C8D18DS29D2 C8D18DS29E2 C8D20DS29A2 C8D20DS29B2 C8D20DS29C2 C8D20DS29D2 C8D20DS29E2 C8D22DS29A2 C8D22DS29B2 C8D22DS29C2 C8D22DS29D2 C8D22DS29E2 C8D25DS29A2 C8D25DS29B2 C8D25DS29C2 C8D25DS29D2 C8D25DS29E2 C8D28DS29A2 C8D28DS29B2 C8D28DS29C2 C8D28DS29D2 C8D28DS29E2 C8D30DS29A2 C8D30DS29B2 C8D30DS29C2 C8D30DS29D2 C8D30DS29E2 C8D31DS29A2 C8D31DS29B2 C8D31DS29C2 C8D31DS29D2 C8D31DS29E2 C8D35DS29A2 C8D35DS29B2 C8D35DS29C2 C8D35DS29D2 C8D35DS29E2 C8D36DS29A2 C8D36DS29B2 C8D36DS29C2 C8D36DS29D2 C8D36DS29E2 C8D40DS29A2 C8D40DS29B2 C8D40DS29C2 C8D40DS29D2 C8D40DS29E2 C8D43DS29A2 C8D43DS29B2 C8D43DS29C2 C8D43DS29D2 C8D43DS29E2 31 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Mounting Ear Options Dimensions A B C D E Tail Length .160" [4.06] (DIM “J”) (Continued) 5.835 5.575 5.260 50 148.21 141.61 133.60 6.835 6.575 6.260 60 173.61 167.01 159.00 5.100 129.54 6.100 154.94 4.900 124.46 5.900 149.86 Tail Length .220" [5.59] (DIM “J”) 1.435 1.175 6 36.45 29.85 1.835 1.575 10 46.61 40.01 2.035 1.775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2 . 8 3 5 2 .575 20 72.01 65.41 3.035 2.775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3 . 8 3 5 3 .575 30 97.41 90.81 3.935 3.675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 5.835 5.575 50 148.21 141.61 6.835 6.575 60 173.61 167.01 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C8D50DS29A2 C8D50DS29B2 C8D50DS29C2 C8D50DS29D2 C8D50DS29E2 C8D60DS29A2 C8D60DS29B2 C8D60DS29C2 C8D60DS29D2 C8D60DS29E2 C8D06DS29A3 C8D06DS29B3 C8D06DS29C3 C8D06DS29D3 C8D06DS29E3 C8D10DS29A3 C8D10DS29B3 C8D10DS29C3 C8D10DS29D3 C8D10DS29E3 C8D12DS29A3 C8D12DS29B3 C8D12DS29C3 C8D12DS29D3 C8D12DS29E3 C8D15DS29A3 C8D15DS29B3 C8D15DS29C3 C8D15DS29D3 C8D15DS29E3 C8D18DS29A3 C8D18DS29B3 C8D18DS29C3 C8D18DS29D3 C8D18DS29E3 C8D20DS29A3 C8D20DS29B3 C8D20DS29C3 C8D20DS29D3 C8D20DS29E3 C8D22DS29A3 C8D22DS29B3 C8D22DS29C3 C8D22DS29D3 C8D22DS29E3 C8D25DS29A3 C8D25DS29B3 C8D25DS29C3 C8D25DS29D3 C8D25DS29E3 C8D28DS29A3 C8D28DS29B3 C8D28DS29C3 C8D28DS29D3 C8D28DS29E3 C8D30DS29A3 C8D30DS29B3 C8D30DS29C3 C8D30DS29D3 C8D30DS29E3 C8D31DS29A3 C8D31DS29B3 C8D31DS29C3 C8D31DS29D3 C8D31DS29E3 C8D35DS29A3 C8D35DS29B3 C8D35DS29C3 C8D35DS29D3 C8D35DS29E3 C8D36DS29A3 C8D36DS29B3 C8D36DS29C3 C8D36DS29D3 C8D36DS29E3 C8D40DS29A3 C8D40DS29B3 C8D40DS29C3 C8D40DS29D3 C8D40DS29E3 C8D43DS29A3 C8D43DS29B3 C8D43DS29C3 C8D43DS29D3 C8D43DS29E3 C8D50DS29A3 C8D50DS29B3 C8D50DS29C3 C8D50DS29D3 C8D50DS29E3 C8D60DS29A3 C8D60DS29B3 C8D60DS29C3 C8D60DS29D3 C8D60DS29E3 32 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors 100 x .200 [2.54 x 5.08], .510 [12.95] and .395 [10.03] Card Slot Depth, Full Scoop Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [3.37 to 1.80] Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .180 [4.57] A B C .02 [.51] Contact Gap .390 [9.91] .100 [2.54] Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms Card Slot Depth .705 [17.91] Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 C Related Product Data .180 [4.57] Dim C .040±.003 [1.02±.08] Dia. Daughter Card Edge Pattern— page 57 .200 [5.08] .100 [2.54] 33 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row Full Scoop Dimensions No. of Dual Readout Pos. A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Number .510" [12.95] Card Slot Depth 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18DS29063 W8D20DS29063 W8D22DS29063 W8D25DS29063 W8D28DS29063 W8D30DS29063 W8D35DS29063 W8D36DS29063 W8D40DS29063 W8D43DS29063 W8D45DS29063 W8D50DS29063 W8D60DS29063 .395" [10.03] Card Slot Depth 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18DS29093 W8D20DS29093 W8D22DS29093 W8D25DS29093 W8D28DS29093 W8D30DS29093 W8D35DS29093 W8D36DS29093 W8D40DS29093 W8D43DS29093 W8D45DS29093 W8D50DS29093 W8D60DS29093 34 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series Connectors .125 x .250 [3.18 x 6.35] Centerline, Dip Solder Tails, .300 [7.62] Card Slot Depth Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .020±.010Contact Gap [.51±.25] .145 [3.68] .300 Card Slot Depth [7.62] J D .250 [6.35] E Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .370 [9.40] .100 Typ. [2.54] B A C .250 [6.35] .610 [15.49] Electrical Properties: Operation Voltage—1000 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .060 .180 [1.52] [4.57] .020 Typ. Dia. [0.51] E Environmental Properties: Dim B Operating Temperature— -55˚C to +125˚C Temperature Cycling— .128 [3.25] Dia. MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 .040±.003 [1.02±.08] Dia. Dim E Related Product Data: Daughter Card Edge Pattern— page 57 .250 [6.35] .125 [3.18] Mounting Styles .125 [3.18] Dia. #4-40 .125 [3.18] Dia. .250 [6.35] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole .250 [6.35] Flush Mounting Ear 4-40 Threaded Insert 35 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B C D E Tail Length .130 [3.30] (DIM. “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2 . 6 8 0 2 .420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4 . 3 0 5 4 .045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 4.680 4.420 31 118.87 112.27 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Tail Length .160 [4.06] (DIM. “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2.680 2.420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3 . 9 3 0 3 .670 25 99.82 93.22 4.305 4.045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 4.680 4.420 31 118.87 112.27 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C7D06DS29A1 C7D06DS29B1 C7D06DS29C1 C7D06DS29D1 C7D06DS29E1 C7D10DS29A1 C7D10DS29B1 C7D10DS29C1 C7D10DS29D1 C7D10DS29E1 C7D15DS29A1 C7D15DS29B1 C7D15DS29C1 C7D15DS29D1 C7D15DS29E1 C7D18DS29A1 C7D18DS29B1 C7D18DS29C1 C7D18DS29D1 C7D18DS29E1 C7D22DS29A1 C7D22DS29B1 C7D22DS29C1 C7D22DS29D1 C7D22DS29E1 C7D25DS29A1 C7D25DS29B1 C7D25DS29C1 C7D25DS29D1 C7D25DS29E1 C7D28DS29A1 C7D28DS29B1 C7D28DS29C1 C7D28DS29D1 C7D28DS29E1 C7D30DS29A1 C7D30DS29B1 C7D30DS29C1 C7D30DS29D1 C7D30DS29E1 C7D31DS29A1 C7D31DS29B1 C7D31DS29C1 C7D31DS29D1 C7D31DS29E1 C7D35DS29A1 C7D35DS29B1 C7D35DS29C1 C7D35DS29D1 C7D35DS29E1 C7D36DS29A1 C7D36DS29B1 C7D36DS29C1 C7D36DS29D1 C7D36DS29E1 C7D40DS29A1 C7D40DS29B1 C7D40DS29C1 C7D40DS29D1 C7D40DS29E1 C7D43DS29A1 C7D43DS29B1 C7D43DS29C1 C7D43DS29D1 C7D43DS29E1 C7D50DS29A1 C7D50DS29B1 C7D50DS29C1 C7D50DS29D1 C7D50DS29E1 C7D06DS29A3 C7D06DS29B3 C7D06DS29C3 C7D06DS29D3 C7D06DS29E3 C7D10DS29A3 C7D10DS29B3 C7D10DS29C3 C7D10DS29D3 C7D10DS29E3 C7D15DS29A3 C7D15DS29B3 C7D15DS29C3 C7D15DS29D3 C7D15DS29E3 C7D18DS29A3 C7D18DS29B3 C7D18DS29C3 C7D18DS29D3 C7D18DS29E3 C7D22DS29A3 C7D22DS29B3 C7D22DS29C3 C7D22DS29D3 C7D22DS29E3 C7D25DS29A3 C7D25DS29B3 C7D25DS29C3 C7D25DS29D3 C7D25DS29E3 C7D28DS29A3 C7D28DS29B3 C7D28DS29C3 C7D28DS29D3 C7D28DS29E3 C7D30DS29A3 C7D30DS29B3 C7D30DS29C3 C7D30DS29D3 C7D30DS29E3 C7D31DS29A3 C7D31DS29B3 C7D31DS29C3 C7D31DS29D3 C7D31DS29E3 C7D35DS29A3 C7D35DS29B3 C7D35DS29C3 C7D35DS29D3 C7D35DS29E3 C7D36DS29A3 C7D36DS29B3 C7D36DS29C3 C7D36DS29D3 C7D36DS29E3 C7D40DS29A3 C7D40DS29B3 C7D40DS29C3 C7D40DS29D3 C7D40DS29E3 C7D43DS29A3 C7D43DS29B3 C7D43DS29C3 C7D43DS29D3 C7D43DS29E3 C7D50DS29A3 C7D50DS29B3 C7D50DS29C3 C7D50DS29D3 C7D50DS29E3 36 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B Tail Length .220 [5.59] (DIM. “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2.680 2.420 15 68.07 61.47 3 . 0 5 5 2 .795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4.305 4.045 28 109.35 102.74 4 . 5 5 5 4.295 30 115.70 109.09 4.680 4.420 31 118.87 112.27 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 C D E 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C7D06DS29A4 C7D06DS29B4 C7D06DS29C4 C7D06DS29D4 C7D06DS29E4 C7D10DS29A4 C7D10DS29B4 C7D10DS29C4 C7D10DS29D4 C7D10DS29E4 C7D15DS29A4 C7D15DS29B4 C7D15DS29C4 C7D15DS29D4 C7D15DS29E4 C7D18DS29A4 C7D18DS29B4 C7D18DS29C4 C7D18DS29D4 C7D18DS29E4 C7D22DS29A4 C7D22DS29B4 C7D22DS29C4 C7D22DS29D4 C7D22DS29E4 C7D25DS29A4 C7D25DS29B4 C7D25DS29C4 C7D25DS29D4 C7D25DS29E4 C7D28DS29A4 C7D28DS29B4 C7D28DS29C4 C7D28DS29D4 C7D28DS29E4 C7D30DS29A4 C7D30DS29B4 C7D30DS29C4 C7D30DS29D4 C7D30DS29E4 C7D31DS29A4 C7D31DS29B4 C7D31DS29C4 C7D31DS29D4 C7D31DS29E4 C7D35DS29A4 C7D35DS29B4 C7D35DS29C4 C7D35DS29D4 C7D35DS29E4 C7D36DS29A4 C7D36DS29B4 C7D36DS29C4 C7D36DS29D4 C7D36DS29E4 C7D40DS29A4 C7D40DS29B4 C7D40DS29C4 C7D40DS29D4 C7D40DS29E4 C7D43DS29A4 C7D43DS29B4 C7D43DS29C4 C7D43DS29D4 C7D43DS29E4 C7D50DS29A4 C7D50DS29B4 C7D50DS29C4 C7D50DS29D4 C7D50DS29E4 37 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Cantilever Series .156 x .200 [3.96 x 5.08] Centerline, Dip Solder Tails, .300 [7.62] Card Slot Depth Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .020±.010Contact Gap [.51±.25] .145 [3.68] D .300 Card Slot Depth [7.62] J .200 [5.08] E Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .370 [9.40] .156 Typ. [3.96] B A C .250 [6.35] .610 [15.49] Electrical Properties: Operation Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .060 .180 [1.52] [4.57] .020 Typ. Dia. [0.51] E Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .040±.003 [1.02±.08] Dia. .128 [3.25] Dia. Dim E Related Product Data: Daughter Card Edge Pattern— page 57 .200 [5.08] .156 [3.96] Mounting Styles .125 [3.18] Dia. #4-40 .125 [3.18] Dia. .250 [6.35] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole .250 [6.35] Flush Mounting Ear 4-40 Threaded Insert 38 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B Tail Length .130 [3.30] (DIM. “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3 . 1 8 8 2 .938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 3.968 3.718 20 100.79 94.44 4.280 4.030 22 108.71 102.36 4 . 7 4 8 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 5.528 5.278 30 140.41 134.06 5.684 5.434 31 144.37 138.02 6.308 6.058 35 160.22 153.87 6.464 6.214 36 164.19 157.84 7.088 6.838 40 180.04 173.69 7.556 7.306 43 191.92 185.57 8.648 8.398 50 219.66 213.31 Tail Length .160 [4.06] (DIM. “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3.188 2.938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 3 . 9 6 8 3 .718 20 100.79 94.44 4.280 4.030 22 108.71 102.36 4.748 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 5.528 5.278 30 140.41 134.06 5.684 5.434 31 144.37 138.02 6.308 6.058 35 160.22 153.87 6.464 6.214 36 164.19 157.84 7.088 6.838 40 180.04 173.69 7.556 7.306 43 191.92 185.57 8.648 8.398 50 219.66 213.31 C D E 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 8.085 205.36 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.595 91.31 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 7.964 202.29 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 7.644 194.16 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 8.085 205.36 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.595 91.31 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 7.964 202.29 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 7.644 194.16 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C6D06DS29A1 C6D06DS29B1 C6D06DS29C1 C6D06DS29D1 C6D06DS29E1 C6D10DS29A1 C6D10DS29B1 C6D10DS29C1 C6D10DS29D1 C6D10DS29E1 C6D12DS29A1 C6D12DS29B1 C6D12DS29C1 C6D12DS29D1 C6D12DS29E1 C6D15DS29A1 C6D15DS29B1 C6D15DS29C1 C6D15DS29D1 C6D15DS29E1 C6D18DS29A1 C6D18DS29B1 C6D18DS29C1 C6D18DS29D1 C6D18DS29E1 C6D20DS29A1 C6D20DS29B1 C6D20DS29C1 C6D20DS29D1 C6D20DS29E1 C6D22DS29A1 C6D22DS29B1 C6D22DS29C1 C6D22DS29D1 C6D22DS29E1 C6D25DS29A1 C6D25DS29B1 C6D25DS29C1 C6D25DS29D1 C6D25DS29E1 C6D28DS29A1 C6D28DS29B1 C6D28DS29C1 C6D28DS29D1 C6D28DS29E1 C6D30DS29A1 C6D30DS29B1 C6D30DS29C1 C6D30DS29D1 C6D30DS29E1 C6D31DS29A1 C6D31DS29B1 C6D31DS29C1 C6D31DS29D1 C6D31DS29E1 C6D35DS29A1 C6D35DS29B1 C6D35DS29C1 C6D35DS29D1 C6D35DS29E1 C6D36DS29A1 C6D36DS29B1 C6D36DS29C1 C6D36DS29D1 C6D36DS29E1 C6D40DS29A1 C6D40DS29B1 C6D40DS29C1 C6D40DS29D1 C6D40DS29E1 C6D43DS29A1 C6D43DS29B1 C6D43DS29C1 C6D43DS29D1 C6D43DS29E1 C6D50DS29A1 C6D50DS29B1 C6D50DS29C1 C6D50DS29D1 C6D50DS29E1 C6D06DS29A3 C6D06DS29B3 C6D06DS29C3 C6D06DS29D3 C6D06DS29E3 C6D10DS29A3 C6D10DS29B3 C6D10DS29C3 C6D10DS29D3 C6D10DS29E3 C6D12DS29A3 C6D12DS29B3 C6D12DS29C3 C6D12DS29D3 C6D12DS29E3 C6D15DS29A3 C6D15DS29B3 C6D15DS29C3 C6D15DS29D3 C6D15DS29E3 C6D18DS29A3 C6D18DS29B3 C6D18DS29C3 C6D18DS29D3 C6D18DS29E3 C6D20DS29A3 C6D20DS29B3 C6D20DS29C3 C6D20DS29D3 C6D20DS29E3 C6D22DS29A3 C6D22DS29B3 C6D22DS29C3 C6D22DS29D3 C6D22DS29E3 C6D25DS29A3 C6D25DS29B3 C6D25DS29C3 C6D25DS29D3 C6D25DS29E3 C6D28DS29A3 C6D28DS29B3 C6D28DS29C3 C6D28DS29D3 C6D28DS29E3 C6D30DS29A3 C6D30DS29B3 C6D30DS29C3 C6D30DS29D3 C6D30DS29E3 C6D31DS29A3 C6D31DS29B3 C6D31DS29C3 C6D31DS29D3 C6D31DS29E3 C6D35DS29A3 C6D35DS29B3 C6D35DS29C3 C6D35DS29D3 C6D35DS29E3 C6D36DS29A3 C6D36DS29B3 C6D36DS29C3 C6D36DS29D3 C6D36DS29E3 C6D40DS29A3 C6D40DS29B3 C6D40DS29C3 C6D40DS29D3 C6D40DS29E3 C6D43DS29A3 C6D43DS29B3 C6D43DS29C3 C6D43DS29D3 C6D43DS29E3 C6D50DS29A3 C6D50DS29B3 C6D50DS29C3 C6D50DS29D3 C6D50DS29E3 39 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options No. of Dual Readout Positions Dimensions A B Tail Length .220" [5.59] (DIM. “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3 . 1 8 8 2 .938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 3.968 3.718 20 100.79 94.44 4.280 4.030 22 108.71 102.36 4 . 7 4 8 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 5.528 5.278 30 140.41 134.06 5.684 5.434 31 144.37 138.02 6.308 6.058 35 160.22 153.87 6.464 6.214 36 164.19 157.84 7.088 6.838 40 180.04 173.69 7.556 7.306 43 191.92 185.57 8.648 8.398 50 219.66 213.31 C D E 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 8.085 205.36 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.595 91.31 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 7.964 202.29 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 7.644 194.16 Centered Mounting Ear .125" [3.18] ThruHole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert C6D06DS29A4 C6D06DS29B4 C6D06DS29C4 C6D06DS29D4 C6D06DS29E4 C6D10DS29A4 C6D10DS29B4 C6D10DS29C4 C6D10DS29D4 C6D10DS29E4 C6D12DS29A4 C6D12DS29B4 C6D12DS29C4 C6D12DS29D4 C6D12DS29E4 C6D15DS29A4 C6D15DS29B4 C6D15DS29C4 C6D15DS29D4 C6D15DS29E4 C6D18DS29A4 C6D18DS29B4 C6D18DS29C4 C6D18DS29D4 C6D18DS29E4 C6D20DS29A4 C6D20DS29B4 C6D20DS29C4 C6D20DS29D4 C6D20DS29E4 C6D22DS29A4 C6D22DS29B4 C6D22DS29C4 C6D22DS29D4 C6D22DS29E4 C6D25DS29A4 C6D25DS29B4 C6D25DS29C4 C6D25DS29D4 C6D25DS29E4 C6D28DS29A4 C6D28DS29B4 C6D28DS29C4 C6D28DS29D4 C6D28DS29E4 C6D30DS29A4 C6D30DS29B4 C6D30DS29C4 C6D30DS29D4 C6D30DS29E4 C6D31DS29A4 C6D31DS29B4 C6D31DS29C4 C6D31DS29D4 C6D31DS29E4 C6D35DS29A4 C6D35DS29B4 C6D35DS29C4 C6D35DS29D4 C6D35DS29E4 C6D36DS29A4 C6D36DS29B4 C6D36DS29C4 C6D36DS29D4 C6D36DS29E4 C6D40DS29A4 C6D40DS29B4 C6D40DS29C4 C6D40DS29D4 C6D40DS29E4 C6D43DS29A4 C6D43DS29B4 C6D43DS29C4 C6D43DS29D4 C6D43DS29E4 C6D50DS29A4 C6D50DS29B4 C6D50DS29C4 C6D50DS29D4 C6D50DS29E4 40 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Card Edge Connectors Product Facts ■ ■ ■ ■ ■ ■ ■ Sizes from 6 to 65 dual positions. Contact mating surface optimizes reliability by concentrating the normal force in the actual contact area. Mounting ear options accommodate both Panel and PC Board attachment. Solder stand-offs facilitate cleaning. Bifurcated contact design provides redundant points of contact to maximize reliability. Tail lengths available to accommodate .062" [1.57] through .125" [3.18] thick PCB Boards and Wire Wrap termination. Straight or Right Angle contact configurations. Bifurcated contact design provides maximum reliability Description/Application The modified bellows card edge connectors are dual readout and are designed for reliable termination to double sided PCB boards. Modified Bellows The modified bellows card edge connector offers a variety of tail lengths for solder and wire wrap applications. Contacts are available in straight tail or right angle configurations to meet your individual purpose. The modified bellows line of connectors offers a variety of card slot depths and has optional high temperature plastic insulators. 41 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .100 x .200 [2.54 x 5.08], Straight Dip Solder And Wire Wrap Tails Product Facts .054 - .071 [1.37 - 1.80] P.C. Board Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .300 [7.62] Card Depth .610 [15.49] SECTION X-X ROTATED 90º J Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .200 [5.08] .025 [.64] Sq C D .100 [2.54] Ref. .368 [9.53] SECTION X-X Electrical Properties: E Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B Dim E .128 [3.25] Dia. Related Product Data: .200 [5.08] Polarization Key—page 57 .100 .100 [2.54] Daughter Card Edge Pattern— page 57 P=.040 [1.02] Dip Solder Applications P=.042 [1.07] For Wire Wrap Applications Mounting Styles .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 42 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Dimensions A B Mounting Ear Options C D E Tail Length .160" [4.06] (DIM “J”) 1.835 1.575 10 46.61 40.01 2.035 1.775 12 51.69 45.09 2 . 3 3 5 2 .075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3.035 2.775 22 77.09 70.49 3 . 3 3 5 3 .075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3.935 3.675 31 99.95 93.35 4 . 3 3 5 4 .075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 5.235 4.975 44 132.97 126.37 5.835 5.575 50 148.21 141.61 6.835 6.575 60 173.61 167.01 7.335 7.075 65 186.31 179.71 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 4.660 118.36 5.260 133.60 6.260 159.00 6.760 171.70 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Tail Length .220" [5.59] (DIM “J”) 1.835 1.575 10 46.61 40.01 2.035 1.775 12 51.69 45.09 2.335 2.075 15 59.31 52.71 2.635 2.375 18 66.93 60.33 2.835 2.575 20 72.01 65.41 3 . 0 3 5 2 .775 22 77.09 70.49 3.335 3.075 25 84.71 78.11 3.635 3.375 28 92.33 85.73 3.835 3.575 30 97.41 90.81 3 . 9 3 5 3 .675 31 99.95 93.35 4.335 4.075 35 110.11 103.51 4.435 4.175 36 112.65 106.05 4.835 4.575 40 122.81 116.21 5.135 4.875 43 130.43 123.83 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A8D10DS29A2 A8D10DS29B2 A8D10DS29C2 A8D10DS29D2 A8D10DS29E2 A8D12DS29A2 A8D12DS29B2 A8D12DS29C2 — — A8D15DS29A2 A8D15DS29B2 A8D15DS29C2 A8D15DS29D2 A8D15DS29E2 A8D18DS29A2 A8D18DS29B2 A8D18DS29C2 A8D18DS29D2 A8D18DS29E2 A8D20DS29A2 A8D20DS29B2 A8D20DS29C2 – – A8D22DS29A2 A8D22DS29B2 A8D22DS29C2 – – A8D25DS29A2 A8D25DS29B2 A8D25DS29C2 A8D25DS29D2 A8D25DS29E2 A8D28DS29A2 A8D28DS29B2 A8D28DS29C2 – – A8D30DS29A2 A8D30DS29B2 A8D30DS29C2 A8D30DS29D2 A8D30DS29E2 A8D31DS29A2 A8D31DS29B2 A8D31DS29C2 A8D31DS29D2 A8D31DS29E2 A8D35DS29A2 A8D35DS29B2 A8D35DS29C2 – – A8D36DS29A2 A8D36DS29B2 A8D36DS29C2 – – A8D40DS29A2 A8D40DS29B2 A8D40DS29C2 – – A8D43DS29A2 A8D43DS29B2 A8D43DS29C2 – – A8D44DS29A2 A8D44DS29B2 A8D44DS29C2 – – A8D50DS29A2 A8D50DS29B2 A8D50DS29C2 A8D50DS29D2 A8D50DS29E2 A8D60DS29A2 A8D60DS29B2 A8D60DS29C2 – – A8D65DS29A2 A8D65DS29B2 A8D65DS29C2 A8D65DS29D2 A8D65DS29E2 A8D10DS29A3 A8D10DS29B3 A8D10DS29C3 A8D10DS29D3 A8D10DS29E3 A8D12DS29A3 A8D12DS29B3 A8D12DS29C3 – – A8D15DS29A3 A8D15DS29B3 A8D15DS29C3 A8D15DS29D3 A8D15DS29E3 A8D18DS29A3 A8D18DS29B3 A8D18DS29C3 A8D18DS29D3 A8D18DS29E3 A8D20DS29A3 A8D20DS29B3 A8D20DS29C3 – – A8D22DS29A3 A8D22DS29B3 A8D22DS29C3 – – A8D25DS29A3 A8D25DS29B3 A8D25DS29C3 A8D35DS29D3 A8D35DS29E3 A8D28DS29A3 A8D28DS29B3 A8D28DS29C3 – – A8D30DS29A3 A8D30DS29B3 A8D30DS29C3 A8D30DS29D3 A8D30DS29E3 A8D31DS29A3 A8D31DS29B3 A8D31DS29C3 A8D31DS29D3 A8D31DS29E3 A8D35DS29A3 A8D35DS29B3 A8D35DS29C3 – – A8D36DS29A3 A8D36DS29B3 A8D36DS29C3 – – A8D40DS29A3 A8D40DS29B3 A8D40DS29C3 – – A8D43DS29A3 A8D43DS29B3 A8D43DS29C3 – – 43 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Dimensions A B C Tail Length .220" [5.59] (DIM “J”) (Continued) 5.235 4.975 4.660 44 132.97 126.37 118.36 5.835 5.575 5.260 50 148.21 141.61 133.60 6.835 6.575 6.260 60 173.61 167.01 159.00 7.335 7.075 6.760 65 186.31 179.71 171.70 Mounting Ear Options D E 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Tail Length .560" [14.22] (DIM “J”) for Wire Wrap Termination 1.835 1.575 1.260 1.100 0.900 10 46.61 40.01 32.00 27.94 22.86 2.035 1.775 1.460 1.300 1.100 12 51.69 45.09 37.08 33.02 27.94 2.335 2.075 1.760 1.600 1.400 15 59.31 52.71 44.70 40.64 35.56 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 .700 18 66.93 60.33 52.32 48.26 43.18 2.835 2.575 2.260 2.100 1.900 20 72.01 65.41 57.40 53.34 48.26 3.035 2.775 2.460 2.300 2.100 22 77.09 70.49 62.48 58.42 53.34 3.335 3.075 2.760 2.600 2.400 25 84.71 78.11 70.10 66.04 60.96 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 .700 28 92.33 85.73 77.72 73.66 68.58 3.835 3.575 3.260 3.100 2.900 30 97.41 90.81 82.80 78.74 73.66 3.935 3.675 3.360 3.200 3.100 31 99.95 93.35 85.34 81.28 78.74 4.335 4.075 3.760 3.600 3.400 35 110.11 103.51 95.50 91.44 86.36 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 .500 36 112.65 106.05 98.04 93.98 88.90 4.835 4.575 4.260 4.100 3.900 40 122.81 116.21 108.20 104.14 99.06 5.135 4.875 4.560 4.400 4.200 43 130.43 123.83 115.82 111.76 106.68 5.235 4.975 4.660 4.500 4.300 44 132.97 126.37 118.36 114.30 109.22 5.835 5.575 5.260 5.100 4.800 50 148.21 141.61 133.60 129.54 121.92 6.835 6.575 6.260 6.100 5.900 60 173.61 167.01 159.00 154.94 149.86 7.335 7.075 6.760 6.600 6.400 65 186.31 179.71 171.70 167.64 162.56 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A8D44DS29A3 A8D44DS29B3 A8D44DS29C3 – – A8D50DS29A3 A8D50DS29B3 A8D50DS29C3 A8D50DS29D3 A8D50DS29E3 A8D60DS29A3 A8D60DS29B3 A8D60DS29C3 – – A8D65DS29A3 A8D65DS29B3 A8D65DS29C3 A8D65DS29D3 A8D65DS29E3 A8D10WW29A3 A8D10WW29B3 – – – A8D12WW29A3 A8D12WW29B3 – – – A8D15WW29A3 A8D15WW29B3 – – – A8D18WW29A3 A8D18WW29B3 – – – A8D20WW29A3 A8D20WW29B3 – – – A8D22WW29A3 A8D22WW29B3 – – – A8D25WW29A3 A8D25WW29B3 – – – A8D28WW29A3 A8D28WW29B3 – – – A8D30WW29A3 A8D30WW29B3 – – – A8D31WW29A3 A8D31WW29B3 – – – A8D35WW29A3 A8D35WW29B3 – – – A8D36WW29A3 A8D36WW29B3 – – – A8D40WW29A3 A8D40WW29B3 – – – A8D43WW29A3 A8D43WW29B3 – – – A8D44WW29A3 A8D44WW29B3 – – – A8D50WW29A3 A8D50WW29B3 – – – A8D60WW29A3 A8D60WW29B3 – – – A8D65WW29A3 A8D65WW29B3 – – – 44 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .100 x .200 [2.54 x 5.08] and .100 x .150 [2.54 x 3.81] Right Angle Dip Solder Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .14±.01 [3.56±.25] .025 Sq. Typ. [.64] H SECTION X-X ROTATED 90º Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .054±.071 [1.37±1.890] PC Board C D .100 Ref. [2.54] .368 [9.35] SECTION X-X Electrical Properties: E Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .128 [3.25] Dia. Dim E .040±.003 [1.02±.08] Dia. Related Product Data: Polarization Key—page 57 Daughter Card Edge Pattern— page 57 Dim G Dim K .100 .100 [2.54] Dim H Row to Row Spacing Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only .250 [6.35] Mounting Styles .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole .610 .610 [15.49] Ref. [15.49] Ref. No Mounting Ears .180 [4.57] Centered Mounting Ear .125 [3.18] Cross Drilled Hole .250 [6.35] Flush Mounting Ear .125 [3.18] Cross Drilled Hole 45 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions 10 12 15 18 20 22 25 28 30 31 35 36 40 43 44 50 60 65 Dimensions Mounting Ear Options A B C D E 1.835 46.61 2.035 51.69 2.335 59.31 2.635 66.93 2.835 72.01 3.035 77.09 3.335 84.71 3.635 92.33 3.835 97.41 3.935 99.95 4.335 110.11 4.435 112.65 4.835 122.81 5.135 130.43 5.235 132.97 5.835 148.21 6.835 173.61 7.335 186.31 1.575 40.01 1.775 45.09 2.075 52.71 2.375 60.33 2.575 65.41 2.775 70.49 3.075 78.11 3.375 85.73 3.575 90.81 3.675 93.35 4.075 103.51 4.175 106.05 4.575 116.21 4.875 123.83 4.975 126.37 5.575 141.61 6.575 167.01 7.075 179.71 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 4.660 118.36 5.260 133.60 6.260 159.00 6.760 171.70 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Centered Mounting Ear Only G 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 Flush Mounting Ear Only K 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole A8D10RA29A A8D10RA29C A8D10RA29E A8D10RA29F A8D12RA29A A8D12RA29C A8D12RA29E – A8D15RA29A A8D15RA29C A8D15RA29E A8D15RA29F A8D18RA29A A8D18RA29C A8D18RA29E A8D18RA29F A8D20RA29A A8D20RA29C A8D20RA29E – A8D22RA29A A8D22RA29C A8D22RA29E – A8D25RA29A A8D25RA29C A8D25RA29E A8D25RA29F A8D28RA29A A8D28RA29C A8D28RA29E – A8D30RA29A A8D30RA29C A8D30RA29E A8D30RA29F A8D31RA29A A8D31RA29C A8D31RA29E A8D31RA29F A8D35RA29A A8D35RA29C A8D35RA29E – A8D36RA29A A8D36RA29C A8D36RA29E – A8D40RA29A A8D40RA29C A8D40RA29E – A8D43RA29A A8D43RA29C A8D43RA29E – A8D44RA29A A8D44RA29C A8D44RA29E – A8D50RA29A A8D50RA29C A8D50RA29E A8D50RA29F A8D60RA29A A8D60RA29C A8D60RA29E – A8D65RA29A A8D65RA29C A8D65RA29E A8D65RA29F 46 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .100" [2.54] Centerline / .150" [3.81] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions 10 12 15 18 20 22 25 28 30 31 35 36 40 43 44 50 60 65 Dimensions Mounting Ear Options A B C D E 1.835 46.61 2.035 51.69 2.335 59.31 2.635 66.93 2.835 72.01 3.035 77.09 3.335 84.71 3.635 92.33 3.835 97.41 3.935 99.95 4.335 110.11 4.435 112.65 4.835 122.81 5.135 130.43 5.235 132.97 5.835 148.21 6.835 173.61 7.335 186.31 1.575 40.01 1.775 45.09 2.075 52.71 2.375 60.33 2.575 65.41 2.775 70.49 3.075 78.11 3.375 85.73 3.575 90.81 3.675 93.35 4.075 103.51 4.175 106.05 4.575 116.21 4.875 123.83 4.975 126.37 5.575 141.61 6.575 167.01 7.075 179.71 1.260 32.00 1.460 37.08 1.760 44.70 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 4.660 118.36 5.260 133.60 6.260 159.00 6.760 171.70 1.100 27.94 1.300 33.02 1.600 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 4.500 114.30 5.100 129.54 6.100 154.94 6.600 167.64 0.900 22.86 1.100 27.94 1.400 35.56 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.100 78.74 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.300 109.22 4.800 121.92 5.900 149.86 6.400 162.56 Centered Mounting Ear Only G 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 Flush Centered Mounting Mounting Ear Ear Only .125" [3.18] K Thru Hole 0.240 A8D10RA29AM233 6.10 0.240 A8D12RA29AM233 6.10 0.240 A8D15RA29AM233 6.10 0.240 A8D18RA29AM233 6.10 0.240 A8D20RA29AM233 6.10 0.240 A8D22RA29AM233 6.10 0.240 A8D25RA29AM233 6.10 0.240 A8D28RA29AM233 6.10 0.240 A8D30RA29AM233 6.10 0.240 A8D31RA29AM233 6.10 0.240 A8D35RA29AM233 6.10 0.240 A8D36RA29AM233 6.10 0.240 A8D40RA29AM233 6.10 0.240 A8D43RA29AM233 6.10 0.240 A8D44RA29AM233 6.10 0.240 A8D50RA29AM233 6.10 0.240 A8D60RA29AM233 6.10 0.240 A8D65RA29AM233 6.10 No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole A8D10RA29CM233 A8D10RA29EM233 A8D10RA29FM233 A8D12RA29CM233 A8D12RA29EM233 – A8D15RA29CM233 A8D15RA29EM233 A8D15RA29FM233 A8D18RA29CM233 A8D18RA29EM233 A8D18RA29FM233 A8D20RA29CM233 A8D20RA29EM233 – A8D22RA29CM233 A8D22RA29EM233 – A8D25RA29CM233 A8D25RA29EM233 A8D25RA29FM233 A8D28RA29CM233 A8D28RA29EM233 – A8D30RA29CM233 A8D30RA29EM233 A8D30RA29FM233 A8D31RA29CM233 A8D31RA29EM233 A8D31RA29FM233 A8D35RA29CM233 A8D35RA29EM233 – A8D36RA29CM233 A8D36RA29EM233 – A8D40RA29CM233 A8D40RA29EM233 – A8D43RA29CM233 A8D43RA29EM233 – A8D44RA29CM233 A8D44RA29EM233 – A8D50RA29CM233 A8D50RA29EM233 A8D50RA29FM233 A8D60RA29CM233 A8D60RA29EM233 – A8D65RA29CM233 A8D65RA29EM233 A8D65RA29FM233 47 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .125 x .250 [3.18 x 6.35], Centerline Straight Dip Solder and Wire Wrap Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .054±.071 [1.37±1.890] PC Board .300 [7.62] Card Depth .610 [5.49] Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum SECTION X-X ROTATED 90º J .250 [6.35] .025 Sq. [.64] C D .125 Ref. [3.18] .368 [9.35] SECTION X-X Electrical Properties: Operation Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms E B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B P .128 [3.25] Dia. ±.003 Dia. [±.080] Dim E Related Product Data: .250 [6.35] Polarization Key—page 57 Daughter Card Edge Pattern— page 57 .125 [3.18] P=.040 [1.02] Dip Solder Applications P=.042 [1.07] For Wire Wrap Applications Mounting Styles .250 [6.35] .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears Flush Mounting Ear .125 [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded Insert 48 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row Dip Solder No. of Dual Readout Positions Mounting Ear Options Dimensions A B Tail Length .160" [4.06] (DIM “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2 . 6 8 0 2 .420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3.555 3.295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4 . 3 0 5 4 .045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 C D E 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A7D06DS29A2 A7D06DS29B2 A7D06DS29C2 A7D06DS29D2 A7D06DS29E2 A7D10DS29A2 A7D10DS29B2 A7D10DS29C2 A7D10DS29D2 A7D10DS29E2 A7D15DS29A2 A7D15DS29B2 A7D15DS29C2 A7D15DS29D2 A7D15DS29E2 A7D18DS29A2 A7D18DS29B2 A7D18DS29C2 A7D18DS29D2 A7D18DS29E2 A7D22DS29A2 A7D22DS29B2 A7D22DS29C2 – – A7D25DS29A2 A7D25DS29B2 A7D25DS29C2 A7D25DS29D2 A7D25DS29E2 A7D28DS29A2 A7D28DS29B2 A7D28DS29C2 – – A7D30DS29A2 A7D30DS29B2 A7D30DS29C2 A7D30DS29D2 A7D30DS29E2 A7D35DS29A2 A7D35DS29B2 A7D35DS29C2 – – A7D36DS29A2 A7D36DS29B2 A7D36DS29C2 – – A7D40DS29A2 A7D40DS29B2 A7D40DS29C2 – – A7D43DS29A2 A7D43DS29B2 A7D43DS29C2 – – A7D50DS29A2 A7D50DS29B2 A7D50DS29C2 A7D50DS29D2 A7D50DS29E2 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded insert No Mounting Ears Flush Mounting Ear .125" [3.18] Thru Hole Flush Mounting Ear 4-40 Threaded insert A7D06WW29A3 A7D06WW29B3 – – – A7D10WW29A3 A7D10WW29B3 – – – A7D15WW29A3 A7D15WW29B3 – – – A7D18WW29A3 A7D18WW29B3 – – – A7D22WW29A3 A7D22WW29B3 – – – A7D25WW29A3 A7D25WW29B3 – – – A7D28WW29A3 A7D28WW29B3 – – – A7D30WW29A3 A7D30WW29B3 – – – A7D35WW29A3 A7D35WW29B3 – – – A7D36WW29A3 A7D36WW29B3 – – – A7D40WW29A3 A7D40WW29B3 – – – A7D43WW29A3 A7D43WW29B3 – – – A7D50WW29A3 A7D50WW29B3 – – – .125" [3.18] Centerline / .250" [6.35] Row-to-Row Wire Wrap No. of Dual Readout Positions Mounting Ear Options Dimensions A B Tail Length .560" [14.22] (DIM “J”) 1.555 1.295 6 39.50 32.89 2.055 1.795 10 52.20 45.59 2.680 2.420 15 68.07 61.47 3.055 2.795 18 77.60 70.99 3 . 5 5 5 3 .295 22 90.30 83.69 3.930 3.670 25 99.82 93.22 4.305 4.045 28 109.35 102.74 4.555 4.295 30 115.70 109.09 5.180 4.920 35 131.57 124.97 5.305 5.045 36 134.75 128.14 5.805 5.545 40 147.45 140.84 6.180 5.920 43 156.97 150.37 7.055 6.795 50 179.20 172.59 C D E 1.035 26.29 1.535 38.99 2.160 54.86 2.535 64.39 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 49 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .125 x .250 [3.18 x 6.35], .125 x .150 [3.18 x 3.81], .125 x .200 [3.18 x 5.08] Centerline, Right Angle Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .14±.01 [3.56±.25] .025 Sq. Typ. [.64] H Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .054±.071 [1.37±1.890] PC Board SECTION X-X ROTATED 90º C D .125 REF [3.18] .368 [9.35] SECTION X-X Electrical Properties: E Operation Voltage—1000 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .128 [3.25] Dia. Dim E .040±.003 [1.02±.08] Dia. Related Product Data: Polarization Key—page 57 Dim H Row to Row Spacing .125 [3.18] Dim G Dim K Daughter Card Edge Pattern— page 57 Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only Mounting Styles .250 [6.35] .250 [6.35] .610 [15.49] Ref. .180 Centered Mounting Ear [4.57] .125 [3.18] Thru Hole .610 [15.49] Ref. No Mounting Ears .610 [15.49] Ref. Centered Mounting Ear .180 .125 [3.18] Thru Hole [4.57] .250 [6.35] Flush Mounting Ear .125 [3.18] Cross Drilled Hole 50 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions Dimensions Mounting Ear Options D E Centered Mounting Ear Only G 0.875 22.23 1.375 34.93 2.000 50.80 2.375 60.33 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.420 10.67 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 0.240 6.10 A7D06RA29AM231 A7D06RA29CM231 A7D06RA29EM231 A7D06RA29FM231 A7D10RA29AM231 A7D10RA29CM231 A7D10RA29EM231 A7D10RA29FM231 A7D15RA29AM231 A7D15RA29CM231 A7D15RA29EM231 A7D15RA29FM231 A7D18RA29AM231 A7D18RA29CM231 A7D18RA29EM231 A7D18RA29FM231 A7D22RA29AM231 A7D22RA29CM231 A7D22RA29EM231 A7D22RA29FM231 A7D25RA29AM231 A7D25RA29CM231 A7D25RA29EM231 A7D25RA29FM231 A7D28RA29AM231 A7D28RA29CM231 A7D28RA29EM231 A7D28RA29FM231 A7D30RA29AM231 A7D30RA29CM231 A7D30RA29EM231 A7D30RA29FM231 A7D35RA29AM231 A7D35RA29CM231 A7D35RA29EM231 A7D35RA29FM231 A7D36RA29AM231 A7D36RA29CM231 A7D36RA29EM231 A7D36RA29FM231 A7D40RA29AM231 A7D40RA29CM231 A7D40RA29EM231 A7D40RA29FM231 A7D43RA29AM231 A7D43RA29CM231 A7D43RA29EM231 A7D43RA29FM231 A7D50RA29AM231 A7D50RA29CM231 A7D50RA29EM231 A7D50RA29FM231 .200" [5.08] Row-to-Row (Dim. “H”) Spacing 1.555 1.295 1.035 0.875 6 39.50 32.89 26.29 22.23 2.055 1.795 1.535 1.375 10 52.20 45.59 38.99 34.93 2.680 2.420 2.160 2.000 15 68.07 61.47 54.86 50.80 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 .375 18 77.60 70.99 64.39 60.33 3.555 3.295 3.035 2.875 22 90.30 83.69 77.09 73.03 3.930 3.670 3.410 3.250 25 99.82 93.22 86.61 82.55 4.305 4.045 3.785 3.625 28 109.35 102.74 96.14 92.08 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 .875 30 115.70 109.09 102.49 98.43 5.180 4.920 4.660 4.500 35 131.57 124.97 118.36 114.30 5.305 5.045 4.785 4.625 36 134.75 128.14 121.54 117.48 5.805 5.545 5.285 5.125 40 147.45 140.84 134.24 130.18 6.180 5.920 5.660 5.500 43 156.97 150.37 143.76 139.70 7.055 6.795 6.535 6.375 50 179.20 172.59 165.99 161.93 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.470 11.94 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 A7D06RA29AM232 A7D06RA29CM232 A7D06RA29EM232 A7D06RA29FM232 A7D10RA29AM232 A7D10RA29CM232 A7D10RA29EM232 A7D10RA29FM232 A7D15RA29AM232 A7D15RA29CM232 A7D15RA29EM232 A7D15RA29FM232 A7D18RA29AM232 A7D18RA29CM232 A7D18RA29EM232 A7D18RA29FM232 A7D22RA29AM232 A7D22RA29CM232 A7D22RA29EM232 A7D22RA29FM232 A7D25RA29AM232 A7D25RA29CM232 A7D25RA29EM232 A7D25RA29FM232 A7D28RA29AM232 A7D28RA29CM232 A7D28RA29EM232 A7D28RA29FM232 A7D30RA29AM232 A7D30RA29CM232 A7D30RA29EM232 A7D30RA29FM232 A7D35RA29AM232 A7D35RA29CM232 A7D35RA29EM232 A7D35RA29FM232 A7D36RA29AM232 A7D36RA29CM232 A7D36RA29EM232 A7D36RA29FM232 A7D40RA29AM232 A7D40RA29CM232 A7D40RA29EM232 A7D40RA29FM232 A7D43RA29AM232 A7D43RA29CM232 A7D43RA29EM232 A7D43RA29FM232 A7D50RA29AM232 A7D50RA29CM232 A7D50RA29EM232 A7D50RA29FM232 A B C .150" [3.81] Row-to-Row (Dim. “H”) Spacing 1.555 1.295 1.035 6 39.50 32.89 26.29 2.055 1.795 1.535 10 52.20 45.59 38.99 2.680 2.420 2.160 15 68.07 61.47 54.86 3 . 0 5 5 2 . 7 9 5 2 .535 18 77.60 70.99 64.39 3.555 3.295 3.035 22 90.30 83.69 77.09 3.930 3.670 3.410 25 99.82 93.22 86.61 4.305 4.045 3.785 28 109.35 102.74 96.14 4 . 5 5 5 4 . 2 9 5 4 .035 30 115.70 109.09 102.49 5.180 4.920 4.660 35 131.57 124.97 118.36 5.305 5.045 4.785 36 134.75 128.14 121.54 5.805 5.545 5.285 40 147.45 140.84 134.24 6.180 5.920 5.660 43 156.97 150.37 143.76 7.055 6.795 6.535 50 179.20 172.59 165.99 Flush Mounting Ear Only K Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole 51 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .125" [3.18] Centerline / .250" [6.35] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions Dimensions A B C Mounting Ear Options E Centered Mounting Ear Only G Flush Mounting Ear Only K Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears 0.625 15.88 1.125 28.58 1.750 44.45 2.125 53.98 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.520 13.21 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 0.340 8.64 A7D06RA29A A7D06RA29C A7D06RA29E A7D06RA29F A7D10RA29A A7D10RA29C A7D10RA29E A7D10RA29F A7D15RA29A A7D15RA29C A7D15RA29E A7D15RA29F A7D18RA29A A7D18RA29C A7D18RA29E A7D18RA29F A7D22RA29A A7D22RA29C A7D22RA29E A7D22RA29F A7D25RA29A A7D25RA29C A7D25RA29E A7D25RA29F A7D28RA29A A7D28RA29C A7D28RA29E A7D28RA29F A7D30RA29A A7D30RA29C A7D30RA29E A7D30RA29F A7D35RA29A A7D35RA29C A7D35RA29E A7D35RA29F A7D36RA29A A7D36RA29C A7D36RA29E A7D36RA29F A7D40RA29A A7D40RA29C A7D40RA29E A7D40RA29F A7D43RA29A A7D43RA29C A7D43RA29E A7D43RA29F A7D50RA29A A7D50RA29C A7D50RA29E A7D50RA29F D .250" [6.35] Row-to-Row (Dim. “H”) Spacing 1.555 1.295 1.035 0.875 6 39.50 32.89 26.29 22.23 2.055 1.795 1.535 1.375 10 52.20 45.59 38.99 34.93 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 .000 15 68.07 61.47 54.86 50.80 3.055 2.795 2.535 2.375 18 77.60 70.99 64.39 60.33 3.555 3.295 3.035 2.875 22 90.30 83.69 77.09 73.03 3.930 3.670 3.410 3.250 25 99.82 93.22 86.61 82.55 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 .625 28 109.35 102.74 96.14 92.08 4.555 4.295 4.035 3.875 30 115.70 109.09 102.49 98.43 5.180 4.920 4.660 4.500 35 131.57 124.97 118.36 114.30 5.305 5.045 4.785 4.625 36 134.75 128.14 121.54 117.48 5.805 5.545 5.285 5.125 40 147.45 140.84 134.24 130.18 6.180 5.920 5.660 5.500 43 156.97 150.37 143.76 139.70 7.055 6.795 6.535 6.375 50 179.20 172.59 165.99 161.93 Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole 52 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors, .156 x .200 [3.96 x 5.08] Centerline, Straight Dip Solder and Wire Wrap Tails Product Facts .054±.071 [1.37±1.890 ] PC Board Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .300 [7.62] Card Depth .610 [5.49] SECTION X-X ROTATED 90º J Physical Properties: Insulation Resistance— 5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .200 [5.08] .025 Sq. [.64] C D .156 Ref. [3.96] .368 [9.35] SECTION X-X Electrical Properties: E Operation Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B Dim E P±.003 [.08] Dia. .128 [3.25] Dia. Related Product Data: .200 [5.08] Polarization Key—page 57 .156 [3.25] Daughter Card Edge Pattern— page 57 P=.040 [1.02] Dip Solder Applications P=.042 [1.07] For Wire Wrap Applications Mounting Styles .250 [6.35] .610 [15.49] Ref. .180 [4.57] Centered Mounting Ear .125 [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears 53 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] Row-to-Row No. of Dual Readout Positions Mounting Ear Options Dimensions A B C D E Tail Length .160" [4.06] (DIM “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3.188 2.938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 4.280 4.030 22 108.71 102.36 4.748 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 6.464 6.214 36 164.19 157.84 7.556 7.306 43 191.92 185.57 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.717 94.41 4.185 106.30 4.653 118.19 5.901 149.89 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.596 91.34 4.064 103.23 4.532 115.11 5.780 146.81 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 3.276 83.21 3.744 95.10 4.212 106.98 5.460 138.68 6.552 166.42 Tail Length .220" [5.59] (DIM “J”) 1.784 1.534 6 45.31 38.96 2.408 2.158 10 61.16 54.81 2.720 2.470 12 69.09 62.74 3.188 2.938 15 80.98 74.63 3.656 3.406 18 92.86 86.51 4.280 4.030 22 108.71 102.36 4.748 4.498 25 120.60 114.25 5.216 4.966 28 132.49 126.14 6.464 6.214 36 164.19 157.84 7.556 7.306 43 191.92 185.57 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.717 94.41 4.185 106.30 4.653 118.19 5.901 149.89 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.596 91.34 4.064 103.23 4.532 115.11 5.780 146.81 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 3.276 83.21 3.744 95.10 4.212 106.98 5.460 138.68 6.552 166.42 Tail Length .560" [14.22] (DIM “J”) For Wire Wrap Termination 1.784 1.534 1.221 1.100 6 45.31 38.96 31.01 27.94 2.408 2.158 1.845 1.724 10 61.16 54.81 46.86 43.79 2.720 2.470 2.157 2.036 12 69.09 62.74 54.79 51.71 3.188 2.938 2.625 2.504 15 80.98 74.63 66.68 63.60 3.656 3.406 3.093 2.972 18 92.86 86.51 78.56 75.49 4.280 4.030 3.717 3.596 22 108.71 102.36 94.41 91.34 4.748 4.498 4.185 4.064 25 120.60 114.25 106.30 103.23 5.216 4.966 4.653 4.532 28 132.49 126.14 118.19 115.11 6.464 6.214 5.901 5.780 36 164.19 157.84 149.89 146.81 7.556 7.306 6.993 6.872 43 191.92 185.57 177.62 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 3.276 83.21 3.744 95.10 4.212 106.98 5.460 138.68 6.552 166.42 Centered Mounting Ear .125" [3.18] Thru Hole Centered Mounting Ear 4-40 Threaded Insert No Mounting Ears A6D06DS29A2 A6D06DS29B2 A6D06DS29C2 A6D10DS29A2 A6D10DS29B2 A6D10DS29C2 A6D12DS29A2 A6D12DS29B2 A6D12DS29C2 A6D15DS29A2 A6D15DS29B2 A6D15DS29C2 A6D18DS29A2 A6D18DS29B2 A6D18DS29C2 A6D22DS29A2 A6D22DS29B2 A6D22DS29C2 A6D25DS29A2 A6D25DS29B2 A6D25DS29C2 A6D28DS29A2 A6D28DS29B2 A6D28DS29C2 A6D36DS29A2 A6D36DS29B2 A6D36DS29C2 A6D43DS29A2 A6D43DS29B2 A6D43DS29C2 A6D06DS29A3 A6D06DS29B3 A6D06DS29C3 A6D10DS29A3 A6D10DS29B3 A6D10DS29C3 A6D12DS29A3 A6D12DS29B3 A6D12DS29C3 A6D15DS29A3 A6D15DS29B3 A6D15DS29C3 A6D18DS29A3 A6D18DS29B3 A6D18DS29C3 A6D22DS29A3 A6D22DS29B3 A6D22DS29C3 A6D25DS29A3 A6D25DS29B3 A6D25DS29C3 A6D28DS29A3 A6D28DS29B3 A6D28DS29C3 A6D36DS29A3 A6D36DS29B3 A6D36DS29C3 A6D43DS29A3 A6D43DS29B3 A6D43DS29C3 A6D06WW29A3 A6D06WW29B3 – A6D10WW29A3 A6D10WW29B3 – A6D12WW29A3 A6D12WW29B3 – A6D15WW29A3 A6D15WW29B3 – A6D18WW29A3 A6D18WW29B3 – A6D22WW29A3 A6D22WW29B3 – A6D25WW29A3 A6D25WW29B3 – A6D28WW29A3 A6D28WW29B3 – A6D36WW29A3 A6D36WW29B3 – A6D43WW29A3 A6D43WW29B3 – 54 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Modified Bellows Connectors .156 x .200 [3.96 x 5.08] Centerline, .156 x .150 [3.96 x 3.81], Right Angle, Dip Solder Tails Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .14±.01 [3.56±.25] .025 Sq. Typ. [.64] H Physical Properties: Insulation Resistance—5000 megohms minimum. Insertion/Withdrawal Force (Daughter Card)—8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O. High temp. plastic option is available; add suffix M399 to part number. Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum .054±.071 [1.37±1.890] PC Board SECTION X-X ROTATED 90º C D .156 REF [3.96] .368 [9.35] SECTION X-X Electrical Properties: Operation Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance—10 milliohms E B A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202 method 204 Dim B .128 [3.25] Dia. Dim E .040±.003 [1.02±.08] Dia. Related Product Data: Polarization Key—page 57 Daughter Card Edge Pattern— page 57 Dim G Dim K Dim H Row to Row Spacing .156 [3.96] Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only Mounting Styles .250 [6.35] .250 [6.35] .610 [15.49] Ref. .180 Centered Mounting Ear [4.57] .125 [3.18] Thru Hole Catalog 1654080 Issued 7-03 www.tycoelectronics.com .610 [15.49] Ref. No Mounting Ears Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. .610 [15.49] Ref. Centered Mounting Ear .125 [3.18] Thru Hole Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 Flush Mounting Ear .125 [3.18] Cross Drilled Hole South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 55 Card Edge Connectors (Solder Type, Board-to-Board) Ordering Information .156" [3.96] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing No. of Dual Readout Positions Dimensions A B C Mounting Ear Options D E Centered Mounting Ear Only G Flush Mounting Ear Only K Centered Mounting Ear .125" [3.18] Thru Hole No Mounting Ears Centered Flush Mounting Ear Mounting Ear .125" [3.18] .125" [3.18] Cross-Drilled Hole Cross-Drilled Hole .200" [5.08] Row-to-Row (Dim. “H”) Spacing 6 1.784 45.31 1.534 38.96 1.221 31.01 1.100 27.94 0.780 19.81 0.470 11.94 0.290 7.37 A6D06RA29A A6D06RA29C A6D06RA29E A6D06RA29F 10 2.408 61.16 2.158 54.81 1.845 46.86 1.724 43.79 1.404 35.66 0.470 11.94 0.290 7.37 A6D10RA29A A6D10RA29C A6D10RA29E A6D10RA29F 12 2.720 69.09 2.470 62.74 2.157 54.79 2.036 51.71 1.716 43.59 0.470 11.94 0.290 7.37 A6D12RA29A A6D12RA29C A6D12RA29E A6D12RA29F 15 3.188 80.98 2.938 74.63 2.625 66.68 2.504 63.60 2.184 55.47 0.470 11.94 0.290 7.37 A6D15RA29A A6D15RA29C A6D15RA29E A6D15RA29F 18 3.656 92.86 3.406 86.51 3.093 78.56 2.972 75.49 2.652 67.36 0.470 11.94 0.290 7.37 A6D18RA29A A6D18RA29C A6D18RA29E A6D18RA29F 22 4.280 108.71 4.030 102.36 3.717 94.41 3.596 91.34 3.276 83.21 0.470 11.94 0.290 7.37 A6D22RA29A A6D22RA29C A6D22RA29E A6D22RA29F 25 4.748 120.60 4.498 114.25 4.185 106.30 4.064 103.23 3.744 95.10 0.470 11.94 0.290 7.37 A6D25RA29A A6D25RA29C A6D25RA29E A6D25RA29F 28 5.216 132.49 4.966 126.14 4.653 118.19 4.532 115.11 4.212 106.98 0.470 11.94 0.290 7.37 A6D28RA29A A6D28RA29C A6D28RA29E A6D28RA29F 36 6.464 164.19 6.214 157.84 5.901 149.89 5.780 146.81 5.460 138.68 0.470 11.94 0.290 7.37 A6D36RA29A A6D36RA29C A6D36RA29E A6D36RA29F 40 7.088 180.04 6.838 173.69 6.525 165.74 6.404 213.46 6.084 154.53 0.470 11.94 0.290 7.37 A6D40RA29A A6D40RA29C A6D40RA29E A6D40RA29F 43 7.556 191.92 7.306 185.57 6.993 177.62 6.872 174.55 6.552 166.42 0.470 11.94 0.290 7.37 A6D43RA29A A6D43RA29C A6D43RA29E A6D43RA29F .150" [3.81] Row-to-Row (Dim. “H”) Spacing 6 1.784 45.31 1.534 38.96 1.221 31.01 1.100 27.94 0.780 19.81 0.420 10.67 0.240 6.10 A6D06RA29AM233 A6D06RA29CM233 A6D06RA29EM233 A6D06RA29FM233 10 2.408 61.16 2.158 54.81 1.845 46.86 1.724 43.79 1.404 35.66 0.420 10.67 0.240 6.10 A6D10RA29AM233 A6D10RA29CM233 A6D10RA29EM233 A6D10RA29FM233 12 2.720 69.09 2.470 62.74 2.157 54.79 2.036 51.71 1.716 43.59 0.420 10.67 0.240 6.10 A6D12RA29AM233 A6D12RA29CM233 A6D12RA29EM233 A6D12RA29FM233 15 3.188 80.98 2.938 74.63 2.625 66.68 2.504 63.60 2.184 55.47 0.420 10.67 0.240 6.10 A6D15RA29AM233 A6D15RA29CM233 A6D15RA29EM233 A6D15RA29FM233 18 3.656 92.86 3.406 86.51 3.093 78.56 2.972 75.49 2.652 67.36 0.420 10.67 0.240 6.10 A6D18RA29AM233 A6D18RA29CM233 A6D18RA29EM233 A6D18RA29FM233 22 4.280 108.71 4.030 102.36 3.717 94.41 3.596 91.34 3.276 83.21 0.420 10.67 0.240 6.10 A6D22RA29AM233 A6D22RA29CM233 A6D22RA29EM233 A6D22RA29FM233 25 4.748 120.60 4.498 114.25 4.185 106.30 4.064 103.23 3.744 95.10 0.420 10.67 0.240 6.10 A6D25RA29AM233 A6D25RA29CM233 A6D25RA29EM233 A6D25RA29FM233 28 5.216 132.49 4.966 126.14 4.653 118.19 4.532 115.11 4.212 106.98 0.420 10.67 0.240 6.10 A6D28RA29AM233 A6D28RA29CM233 A6D28RA29EM233 A6D28RA29FM233 36 6.464 164.19 6.214 157.84 5.901 149.89 5.780 146.81 5.460 138.68 0.420 10.67 0.240 6.10 A6D36RA29AM233 A6D36RA29CM233 A6D36RA29EM233 A6D36RA29FM233 40 7.088 180.04 6.838 173.69 6.525 165.74 6.404 162.66 6.084 154.53 0.420 10.67 0.240 6.10 A6D40RA29AM233 A6D40RA29CM233 A6D40RA29EM233 A6D40RA29FM233 43 7.556 191.92 7.306 185.57 6.993 177.62 6.872 174.55 6.552 166.42 0.420 10.67 0.240 6.10 A6D43RA29AM233 A6D43RA29CM233 A6D43RA29EM233 A6D43RA29FM233 56 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Card Edge Polarization Keys Description/Application Tyco Electronics can provide polarization keys in the basic configuration shown on this page. Our Modified Bellows and Cantilever Beam Series Card Edge Connectors use these keys. The part number and the connector series for which it was designed are listed in the table below. Break Off Point 45° .24 [6.10] .033 [.84] .19 [4.83] Ordering Information Acquired Part Number 98014-01 98014-01 Used on Connector Series Modified Bellows Cantilever Beam Shown on Pages 41-56 28-40 Card Edge Connectors Recommended Daughter Card Edge Pattern Per MIL-C-21097E .062 [1.57] Board Thickness 30° Slot Depth Min. Contact Spacing Dim. B Dim. A (Per Applicable Catalog Page) .015 [.38] See Note 3 Daughter Card Contact Spacing Non-Accum. .100 [2.54] .125 [3.18] .156 [3.96] Dim A ±.005 (.13) .093 [2.36] .093 [2.36] .105* [2.67] Dim B .052 [1.32] .052 [1.32] .094 [2.39] * Except MIL-C-21097E 8–4 which is .070 [1.78] NOTES: 1. Dimensions are in inches 2. Unless otherwise specified, tolerance is ±.005 [0.13 mm] for three place decimals. 3. Number of contact fingers shall be the same as the corresponding printed wiring connector. 57 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors Product Facts ■ Low profile housing is .460 [11.68] deep ■ 6 through 43 dual positions on .156 [3.96] centerline; 6 though 50 dual positions on .125 [3.18] centerline ■ Solder eyelet for wire-toboard or solder post for mother-daughter board application ■ Selective gold plating of contact area for high performance at low cost ■ Alternate platings are available on request ■ Contacts bifurcated for redundancy ■ Tin plate for high solderability of solder eyelets and posts ■ Accepts .055-.070 [1.401.78] thick printed circuit boards ■ Housings available with or without mounting ears ■ Intercontact keying available ■ UL 94V-0 rated, glass-filled polyester housings ■ Variety of solder post lengths ■ 5 ampere current rating per contact* ■ Recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 For printed circuit board packaging, AMP Low Profile Edge Connectors provide high performance, low cost connections on .125 [3.18] and .156 [3.96] centerline spacings. .100 [2.54] centerline connectors can be made available, consult Tyco Electronics. with either solder posts for mother-daughter board applications or solder eyelet contacts for wire-toboard use. Mounted connector housings extend only .460 [11.68] from the mother board to allow efficient use of available space. Low Profile Edge Connectors feature clear slot entry and accept .055-.070 [1.40-1.78] thick doublesided printed circuit boards. Solder posts are available with .150 [3.18] and .180 [4.57] long tails on .140 [3.56] or .200 [5.08] rowto-row spacing. These low profile connectors are available in 6 through 43 dual position sizes on .156 [3.96] centerline spacing and with 6 through 50 dual positions on .125 [3.18] centers. Connectors are supplied Impact-resistant thermoplastic housing, UL rated 94V-0, have molded-in cavity identification and are available with or without mounting ears. Additional features of the housings include intercontact keying provisions, probe slots and identification of number one position. The precision formed contacts made of phosphor bronze are gold plated on the contact mating surface only. This selective plating provides high reliability while maintaining low cost. Solder eyelets and posts are tin plated for excellent solderability. The contact is bifurcated for redundancy. Shorting contacts are available. All connector configurations are furnished preloaded. Selectively loaded connectors can be made available for added economy. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 58 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .125 [3.18] Centerline Material and Finish: .128 Dia. [3.25] 2 (Plcs.) PCBoard Thickness— .055-.070 [1.40-1.78] Housing—Green, glass-filled polyester Contacts—Phosphor bronze, duplex plated .000030 [0.00076] gold in contact area; .000100 [0.00254] bright tin on posts, with entire contact underplated .000030 [0.00076] nickel .300 C [7.62] .125 [3.18] .150 [3.81] .125 Typ. [3.18] A Related Product Data: Keying Plug—page 63 PC Board Hole Layouts—See below PC Board Edge Pattern—page 63 B D .460 [11.68] Technical Documents: (pages 186, 187): .250 [6.35] Product Specification 108-9044 Instruction Sheet 408-7772 .125 Typ. [3.18] #1 Cavity Identification Molded Characters (Upper and Lower Case Letters Omitting Letters G, I, O &Q) 1 2 3 4 5 6 A B C D E F E .295 [7.49] .125 Ref. [3.18] .295 [7.49] .125 Ref. [3.18] .295 [7.49] .165 [4.19] .165 [4.19] .165 [4.19] Post Length (See Chart) Post Length (See Chart) .200 [5.08] .335 [8.51] Typ. .125 [3.18] B .235 Ref. [5.97] Flow Solder Post .140 [3.56] Row-to-Row Spacing .200 .052 Dia. [5.08] [1.32] .128 Dia. [3.25] .280 Ref. [7.11] .140 [3.56] Flow Solder Post .200 [5.08] Row-to-Row Spacing .100 [2.54] Recommended PC Board Hole Layout Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing .140 .052 Dia. [3.56] [1.32] .128 Dia. [3.25] .335 [8.51] Typ. .125 Ref. [3.18] .125 [3.18] B .070 [1.78] Recommended PC Board Hole Layout 59 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .125 [3.18] Centerline (Continued) Flow Solder Post .200 [5.08] Row-to-Row Spacing No. of Dual Positions A B Dimensions C D E Post Length* With Mounting Ears Without Mounting Ears 6 .875 22.23 — .370 9.40 1.035 26.29 — .150 — 2-530671-1 10 1.375 34.93 1.795 45.59 .370 9.40 1.535 38.99 2.055 52.20 .150 .180 — 2-530663-2 2-530671-2 — 15 2.420 61.47 2.795 70.99 3.295 83.69 — 2-530671-3 .180 2-530663-4 2-530671-4 .150 2-530662-5 2-530671-5 — .150 — 3-530671-3 4.305 109.35 .150 2-530662-6 2-530671-6 — .150 — 2-530671-7 5.045 128.14 5.545 140.84 6.795 172.59 2.160 54.86 2.535 64.39 3.035 77.09 3.285 83.44 3.785 96.14 4.035 102.49 4.785 121.54 5.285 134.24 6.535 165.99 .150 4.045 102.74 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .370 9.40 .437 11.10 .437 11.10 2.680 68.07 3.055 77.60 3.555 90.30 5.305 134.75 5.805 147.45 7.055 179.20 .150 .180 — — 2-530671-9 2-530672-9 .150 — 3-530671-0 50 2.000 50.80 2.375 60.33 2.875 73.03 3.125 79.38 3.625 92.08 3.875 98.43 4.625 117.48 5.125 130.18 6.375 161.93 .150 3-530662-2 — No. of Dual Positions A B Dimensions C D E Post Length* With Mounting Ears Without Mounting Ears 15 2.000 50.80 — .370 9.40 2.160 54.86 — .150 — 2-530673-3 .370 9.40 .437 11.10 3.785 96.14 6.535 165.99 — .150 .180 — 2-530674-6 2-530673-6 — 7.055 179.20 .180 3-530659-2 — 18 22 24 28 30 36 40 Flow Solder Post .140 [3.56] Row-to-Row Spacing 3.625 92.08 6.375 161.93 28 50 Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing No. of Dual Positions 15 22 28 40 50 — — — 6.795 172.59 With Mounting Ears A B Dimensions C D E 2.000 50.80 2.875 73.02 3.625 92.08 5.125 130.17 6.375 161.92 2.420 61.47 3.295 83.69 4.045 102.74 5.545 140.84 6.795 172.59 .370 9.40 .370 9.40 .370 9.40 .437 11.10 .437 11.10 2.160 54.86 3.035 77.08 3.785 96.14 5.285 134.23 6.535 165.98 2.680 68.07 3.555 90.29 4.305 109.35 5.805 147.44 7.055 179.19 2-530664-3 2-530664-5 2-530664-6 3-530664-0 3-530664-2 *Metric equivalents for post length are .150 = [3.81]; .180 = [4.57]. Note: Other connector sizes can be made available, consult Tyco Electronics. 60 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .156 [3.96] Centerline Material and Finish: Mounting Ear with Insert Housing—Green, glass-filled polyester Contacts—Phosphor bronze, duplex plated .000030 [0.00076] gold in contact area; .000100 [0.00254] bright tin on posts, with entire contact underplated .000030 [0.00076] nickel Insert—Brass .128 Dia. [3.25] (2 Plcs.) PCBoard Thickness— .055-.070 [1.40-1.78] .300 [7.62] C .160 [4.06] Threaded Inserts 4-40 NC-2B (2 per connector) Related Product Data: Keying Plug—page 63 PC Board Hole Layouts—See below PC Board Edge Pattern—page 63 .156 Typ. [3.96] A .150 [3.81] B D .460 [11.68] Technical Documents: (pages 186, 187): .250 [6.35] Product Specification 108-9044 Instruction Sheet 408-7772 .156 Typ. [3.96] #1 Cavity Identification Molded Characters (Upper and Lower Case Letters Omitting Letters G, I, O &Q) 1 2 3 4 5 6 A B C D E F E .295 [7.49] .125 Ref. [3.18] .295 [7.49] .125 Ref. [3.18] .295 [7.49] .165 [4.19] .165 [4.19] .165 [4.19] Post Length (See Chart) Post Length (See Chart) .200 [5.08] .156 [3.96] B .235 Ref. [5.97] Flow Solder Post .140 [3.56] Row-to-Row Spacing .200 .052 Dia. [5.08] [1.32] .128 Dia. [3.25] .378 [9.59] Typ. .280 Ref. [7.11] .140 [3.56] Flow Solder Post .200 [5.08] Row-to-Row Spacing .100 [2.54] Recommended PC Board Hole Layout Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing .140 .052 Dia. [3.56] [1.32] .128 Dia. [3.25] .378 [9.59] Typ. .125 Ref. [3.18] .156 [3.96] B .070 [1.78] Recommended PC Board Hole Layout 61 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors, .156 [3.96] Centerline (Continued) Flow Solder Post .200 [5.08] Row-to-Row Spacing Flow Solder Post .140 [3.56] Row-to-Row Spacing and Solder Eyelet Contact .235 [5.97] Row-to-Row Spacing No. of Dual Positions A B 6 1.100 27.94 1.535 38.99 .370 9.40 10 1.724 43.79 2.159 54.84 12 2.036 51.71 2.471 62.76 Dimensions C D E Post Length* 1.240 31.50 1.785 45.34 .150 .370 9.40 1.864 47.35 2.409 61.19 .150 .180 .370 9.40 2.176 55.27 2.721 69.11 .150 15 2.504 63.60 2.939 74.65 .370 9.40 2.644 67.16 3.189 81.00 .150 18 2.972 75.49 3.407 86.54 .370 9.40 3.112 79.04 3.657 92.89 .150 .180 22 3.596 91.34 4.031 102.39 .370 9.40 3.736 94.89 4.281 108.74 .150 25 4.064 103.23 4.499 114.27 .370 9.40 4.204 106.78 4.749 120.62 28 4.532 115.11 4.967 126.16 .370 9.40 4.672 118.67 5.217 132.51 30 4.844 123.04 5.279 134.09 .437 11.10 4.984 126.59 5.529 140.44 36 5.780 146.18 6.215 157.86 .437 11.10 5.920 150.37 6.465 164.21 43 6.872 174.55 7.307 185.60 .437 11.10 7.012 178.10 7.557 191.95 E Post Length* No. of Dual Positions 6 10 15 18 22 24 28 30 36 43 A 1.100 27.94 1.724 43.79 2.504 63.60 2.972 75.49 3.596 91.34 3.908 99.26 4.532 115.11 4.844 123.04 5.780 146.81 6.872 174.55 Dimensions B C D 1.535 .370 1.240 1.785 38.99 9.40 31.50 45.34 2.159 .370 1.864 2.409 54.84 9.40 47.35 61.19 2.939 .370 2.644 3.189 74.65 9.40 67.16 81.00 3.407 .370 3.112 3.657 86.54 9.40 79.04 92.89 4.031 .370 3.736 4.281 102.39 9.40 94.89 108.74 4.343 .370 4.048 4.593 110.31 9.40 102.81 116.66 4.967 .370 4.672 5.217 126.16 9.40 118.67 132.51 5.279 .437 4.984 5.529 134.09 11.10 126.59 140.44 6.215 .437 5.920 6.465 155.58 11.10 150.36 164.21 7.307 .437 7.012 7.557 185.60 11.10 178.10 191.95 .180 .150 .180 .150 .180 .150 .180 .150 .180 .150 .180 With With Without Mounting Mounting Ears Mounting Ears and Inserts Ears 2-530655-1 2-530677-1 — 12-530689-11 — 2-530666-1 2-530655-2 — 2-530666-2 2-530656-2 — — 2-530655-3 — 2-530666-3 2-530655-4 12-530689-41 2-530655-5 — 2-530655-6 12-530689-61 2-530656-6 2-530655-8 2-530656-8 3-530655-2 3-530656-2 2-530655-9 12-530689-91 — 3-530655-0 13-530689-01 3-530655-3 3-530656-3 — — — — — — 2-530678-6 — — — — — — — — — 3-530677-3 — 2-530666-4 — 2-530666-5 2-530667-5 2-530666-6 12-531433-41 2-530667-6 12-531433-11 2-530666-8 3-530666-2 — 2-530666-9 — 2-530667-9 12-531433-21 2-530667-0 3-530666-3 3-530667-3 Flow Solder Post With Without Mounting Mounting Ears Ears Solder Eyelet Contact With Without Mounting Mounting Ears Ears .150 — — 2-530654-1 — .150 2-530657-2 — 2-530654-2 — .150 .180 2-530657-4 — — 2-530669-4 2-530654-4 — 2-530667-4 — .150 — 2-530668-5 2-530654-5 — .150 2-530657-6 2-530668-6 2-530654-6 — .150 — — 2-530654-7 — .150 3-530657-2 3-530668-2 3-530654-2 — — — — 2-530654-9 — .150 .180 — — — 3-530669-0 3-530654-0 — — — .150 3-530657-3 — 3-530654-3 — *Metric equivalents for post length are .150 = [3.81]; .180 = [4.57]. 1For .040 [1.02] diameter hole. Note: Other connector sizes can be made available, consult Tyco Electronics. 62 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Low Profile Connectors (Continued) Keying Plug Intercontact Key Material: Glass-filled nylon Part No. 650025-2 Recommended PC Board Edge Patterns .125 [3.18] Centerline Boards Intercontact KeySlot .300 Min. [7.52] .050 [1.27] .400 [10.16] .125 [3.18] .125 [3.18] .078± .005 .000 [1.98±0.13 0.00] .175 Min. [4.45] Recommended Gold Area .156 [3.96] Centerline Boards Intercontact KeySlot .300 Min. [7.52] .050 [1.27] .400 [10.16] .160 [4.06] .156 [3.96] .094± .005 .000 [2.39±0.13 0.00] .175 Min. [4.45] Recommended Gold Area 63 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors Product Facts ■ Wide variety of sizes available from 3 dual positions and up—no initial tooling investment required for new versions ■ Connectors can be selectively loaded with contacts in custom patterns ■ Connectors tooled on all standard centerlines— .100 [2.54], .125 [3.18], .150 [3.81], .156 [3.96], and .200 [5.08] Note: .200 [5.08] centerline capabilities provided by loading every-other dual position of .100 [2.54] centerline housings. ■ Closed card entry protects contacts and daughter board pads ■ Adapts to a wide range of mother board thicknesses to .104 [2.64] maximum ■ Phosphor bronze contacts selectively plated for top performance and maximum economy ■ Protective channel helps prevent overstress of contacts ■ Daughter board keying available in intercontact or on-contact styles ■ Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 *Consult Tyco Electronics engineering when paralleling contacts for power applications. The AMP Twin Leaf Connector is a highly reliable, low-cost mother/ daughter board connector designed for solid-state circuitry. The one-piece, multi-contact connector requires no front-end tooling. This versatile connector for double-sided printed circuit boards uses preloaded contacts and selective plating to give lowest applied cost. Critical contact areas are gold-over-nickel plated to provide positive electrical connection between contacts and daughter board pads. Contact posts are tin plated for efficient dip soldering to mother boards up to .104 [2.64] thick. The Twin Leaf Connector delivers high reliability because the contacts possess superior tolerance of environmental stresses including shock, vibration and variations of temperature and humidity. Other characteristics such as high insulation resistance, low termination resistance, long life and moderate contact separation force meet industry requirements for reliability. Connectors are tooled in sizes from 3 through 80 dual-contact positions with contacts on .100 [2.54], .125 [3.18], .150 [3.81], .156 [3.96] or .200 [5.08] centers. Other sizes and customloaded contact patterns are available on request. The connector housing, made of glass-filled polyester with a UL 94V-0 rating, features a standoff which facilitates the use of a probe for electrical continuity checks without risk of damage to the contacts. A closed card-entry design of the housing protects the contacts and daughter board pads. Housings accept daughter boards ranging from .055 [1.40] to .070 [1.78] in thickness. Intercontact and on-contact keys are available for polarization of the housings. Card guides or end caps make alignment of daughter board pads with Twin Leaf Connector contacts quick and easy. Performance Specifications Contact Rating*: 3 amperes continuous Temperature Rating: –55°C to +105°C Insulation Resistance: 5,000 megohms Dielectric Withstanding Voltage: Test Voltage (AC, RMS) Contact Spacing .100 [2.54] .150 [3.81] Sea Level 1,000 1,500 50,000 ft 400 600 15 240 m 70,000 ft 280 400 21 336 m Altitude Termination Resistance: 10 milliohms, max. Durability: Tested to 100 cycles (engage/withdraw) Contact Plating: .000015 [0.00038] selective gold plating on contact area; bright tin on solder tine 64 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors Without End Caps .100 [2.54], .125 [3.18], .150 [3.81] and .156 [3.96] Centerlines, With Solder Posts Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000015 [0.00038] gold in contact area; tin on posts, with entire contact underplated .000030 [0.00076] nickel, except where noted .400 [10.16] Fit for .055-.070 [1.4-1.78] PCBoard .225 [5.72] Card Slot Depth .400 [10.16] Max. .610 [15.49] A .135* or .170* [3.43] [4.32] B A Related Product Data: .010 x .024 [0.25 x 0.61] Post for .035 [0.89] Dia. Hole .200 [5.08] D Performance Specifications— page 64 Card Guides—pages 70, 71 Keying Plugs—page 72 PC Board Hole Layouts—page 71 *Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines, except where noted; .170 [4.32] for .100 [2.54] and .125 [3.18] centerlines, except where noted. Technical Documents: (pages 186, 187): Product Specification 108-9027 Instruction Sheets 408-7479, 408-7498, 408-7506 65 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors Without End Caps A = .100 [2.54] Centerline Spacing Part B D Numbers A = .125 [3.18] Centerline Spacing Part B D Numbers 2 — — — 3 .200 5.08 .400 10.16 No. of Dual Positions 4 — — 5 .400 10.16 .600 15.24 8 — — — 583485-6 — 583485-7 — — — — — — — — — — — — — — — — 1.000 25.40 1.250 31.75 A = .150 [3.81] Centerline Spacing Part B D Numbers .300 .600 1,31-583694-1 7.62 15.24 .300 .600 1,3 1,3 7.62 15.24 1-645155-1 .450 .750 583407-5 11.43 19.05 .600 .900 583407-6 15.24 22.86 1.050 1.350 583407-9 26.67 34.29 9 — — 10 .900 22.86 1.100 27.94 1-583485-2 — — — — — 11 — — — — — — 1.500 38.10 1.800 45.72 14 1.300 33.02 1.500 38.10 — — — — — — — 2.100 53.34 2.400 60.96 1-583407-5 15 18 20 22 28 — — — — — — — — — — 1-583485-6 — — — — 2.125 53.97 2.375 60.32 583533-7 — — 4-583486-8 — — — — — — — — — — — — — — 1.400 35.56 1.720 43.69 4-583486-1 — — — — — — — — — 2.964 75.28 3-583486-3 — — 1-583407-2 — — — 3.150 80.01 2-583407-0 530292-93 — — — — — 2.875 73.02 2-583533-0 — — — 4.050 102.87 4.350 110.49 — — — — 2.850 72.39 — 3.875 98.43 — .624 15.85 1-583533-6 2.625 66.67 — — .312 7.92 2.652 67.36 — — A = .156 [3.96] Centerline Spacing Part B D Numbers — — — 4.524 114.91 4.836 122.83 2-583486-3 — 4.212 106.99 4.524 114.91 583407-1 30 — — — 3.625 92.08 31 — — — — — — 4.500 53.34 4.800 60.96 530292-33 — — — 33 — — — — — — — — — 1-583486-8 36 — — — — — — — — — 3-583533-8 5.850 148.59 6.150 156.21 3-583407-8 5.304 134.72 5.772 146.61 6.396 162.46 6.864 174.35 7.960 202.18 8.892 225.86 531534-22 2-583486-1 56 — — — — — — — — — 4.992 126.80 5.460 138.68 6.084 154.53 6.552 166.42 7.640 194.06 8.580 217.93 65 6.400 162.56 7.900 200.66 6.600 167.64 8.100 205.74 5-583485-6 — — — — — — — — — 5-583485-5 — — — — — — — — — 40 43 50 80 — — — — — — 4.900 5.100 124.46 129.54 583485-3 4.875 5.125 123.83 130.18 — — — 6.130 6.380 1 155.70 162.05 5-583533-0 — — — 7.350 186.69 7.650 194.31 4-583407-8 1-583486-5 1-583486-1 583486-8 583486-1 5-583486-0 1Contacts are plated .000030 [0.00076] gold in contact area, tin on posts, with entire contact underplated .000030 [0.00076] nickel. length .135 [3.43] 3Post length .170 [4.32] Note: Other connector sizes can be made available, consult Tyco Electronics. 2Post 66 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors With End Caps .100 [2.54], .125 [3.18], .150 [3.81] and .156 [3.96] Centerlines, With Solder Posts Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000015 [0.00038] gold in contact area; tin on posts, with entire contact underplated .000030 [0.00076] nickel Related Product Data: Performance Specifications— page 64 Keying Plugs—page 72 PC Board Hole Layouts—page 71 Technical Documents: (pages 186, 187): Product Specification 108-9027 Instruction Sheets 408-7479, 408-7498, 408-7506 .400 [10.16] F Fit for .055-.070 [1.4-1.78] PCBoard .225 [5.72] Card Slot Depth .400 [10.16] Max. .610 [15.49] .135* or .170* [3.43] [4.32] .062 [1.58] A B E** G Accepts #2 Self-tapping Screw .200 [5.08] .010 x .024 [0.25 x 0.61] Post for .035 [0.89] Dia. Hole **Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines; .170 [4.32] for .100 [2.54] and .125 [3.18] centerlines. **See page 27 for dimensions. 67 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors With End Caps No. of Dual Pos. 3 5 6 7 9 10 12 13 A = .100 [2.54] Centerline Spacing Part B F G Numbers .200 .400 .734 1-583715-1 5.03 10.16 18.64 .400 .600 .934 1-583715-3 10.16 15.24 23.72 .500 .700 1.034 1-583715-4 12.70 17.78 26.26 .600 .800 1.134 1-583715-5 15.24 20.32 28.80 .800 1.000 1.334 1-583715-7 20.32 25.40 33.88 .900 1.100 1.434 1-583715-8 22.86 27.94 36.42 1.100 1.300 1.634 1-583715-0 27.94 33.02 41.50 1.200 1.400 1.734 1-583715-1 30.48 35.56 44.04 A = .125 [3.18] Centerline Spacing Part B F G Numbers — — — A = .150 [3.81] Centerline Spacing Part B F G Numbers B — — — — — — — — — — — — — — — — — 1.259 31.96 1-583679-5 — — — — .780 19.81 1.092 27.74 1.538 39.07 1-583660-6 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 1.716 43.59 2.028 51.51 2.162 54.91 2.474 62.84 1-583660-0 — 1.404 35.66 1.716 43.58 — — — — — — — — — — — — — 2.250 57.15 2.400 60.96 2.684 68.17 2.834 71.98 1-583692-3 2.340 59.44 2.496 63.40 2.786 70.76 2.942 74.73 1-583660-4 1-583692-4 2.028 51.51 2.184 55.47 — — — — — — — 2.652 67.36 2.964 75.28 3.410 86.61 1-583660-7 — — — — 15 1.934 49.12 2.134 54.20 2.234 56.74 2.434 61.82 1-583715-3 — — — — 1-583715-5 2.250 57.15 2.375 60.33 2.625 66.68 2.634 66.90 2.759 70.08 3.009 76.43 — 1-583715-8 2.000 50.80 2.125 53.98 2.375 60.33 1-583679-6 20 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 22 — — — — — — — 25 2.400 60.96 2.500 63.50 2.700 68.58 2.900 73.66 3.000 76.20 3.100 78.74 2.600 66.04 2.700 68.58 2.900 73.66 3.100 78.74 3.200 81.28 3.300 83.82 2.934 74.52 3.034 77.05 3.234 82.14 3.434 87.22 3.534 89.76 3.634 92.30 2-583715-3 3.000 76.20 3.250 82.55 2-583715-4 — — 2-583715-6 3.375 85.73 3.625 92.08 26 28 30 31 32 — — — — — — 1-583679-9 — — — — — — — — — — — — — 2-583679-4 3.600 91.44 3.900 99.06 4.334 110.08 2-583692-4 3.588 91.14 4.065 103.02 4.034 102.46 4.502 114.35 2-583660-1 3.634 92.30 3.276 83.21 3.744 95.10 — — — — — — — — — — 4.524 114.91 4.836 122.83 4.979 126.24 5.282 134.16 2-583660-7 4.009 101.83 2-583679-6 — — — — 4.650 118.11 5.084 129.13 1-583692-1 — — — — — — — 5.148 130.76 5.594 142.09 3-583660-1 — — — — — — — — — — — — — — — 5.100 129.54 5.534 140.56 3-583692-1 — — — — — — — — — 5.616 142.64 5.772 146.61 6.062 153.97 6.218 157.94 3-583660-4 3-583692-4 5.304 134.72 5.460 138.68 3-583692-8 — — — — 33 — — — — — — — — 34 3.500 88.90 3.600 91.44 3.700 93.98 4.100 104.14 4.200 106.68 3.834 97.38 3.934 99.92 4.034 102.46 4.434 112.62 4.534 115.16 3-583715-2 — — — — — — — 5.100 129.54 5.250 133.35 5.850 148.59 5.400 137.16 5.550 140.97 6.150 156.21 5.834 148.18 5.984 151.99 6.584 167.23 3-583692-3 41 3.300 83.82 3.400 83.36 3.500 88.90 3.900 99.06 4.000 101.60 43 — — — 50 4.900 124.46 7.900 200.66 5.100 129.54 8.100 205.74 5.434 138.02 8.434 214.22 36 40 80 2-583660-9 4.836 122.83 4.800 121.92 35 2-583660-4 4.212 106.98 4.524 114.91 2-583715-9 — 1-583660-2 — 2-583715-8 — 1-583660-2 1-583679-7 4.350 110.49 3-583715-0 — .875 22.23 1.400 35.56 1.600 40.64 1.700 43.18 1.900 48.26 1-583715-6 — — 14 18 — .625 15.88 1.950 49.53 2.100 53.34 17 A = .156 [3.96] Centerline Spacing Part F G Numbers 3-583715-3 — — — — 3-583715-4 — — — — 3-583715-8 4.875 123.83 3-583715-9 — — — — — — — — — — — — — — — — — — — — — 6.125 155.58 7.350 186.69 7.650 194.31 8.084 205.33 4-583692-8 6.864 174.35 7.956 202.08 7.310 185.67 8.402 213.41 4-583660-1 4-583715-8 6.552 166.42 7.644 194.16 5-583715-7 — — — — — — — — — 5.125 5.509 130.18 139.93 3-583679-8 6.375 6.759 161.93 171.68 4-583679-8 — — — 1-583660-1 4-583660-8 Note: Other connector sizes can be made available, consult Tyco Electronics. 68 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors With End Caps (Continued) Typical Connector and Card Guide Assembly Double Slotted Card Guide (Without Stand-off) Single Slotted Card Guide Double Slotted Card Guide (With Stand-off) End Cap Stand-off Daughter Board Mother Board .104 [2.64] Max. Thickness* Self-tapping #2 Screw (2 Reqd.) Self-tapping #2 Screw (1 Reqd.) Self-tapping #2 Screw (2 Reqd.) *Must be .063 [1.59] thick for use with Double Slotted Card Guides. 69 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors (Continued) Card Guides Single Slotted Material: Glass-filled nylon, black .210 [5.33] Part No. 583671-1 Related Product Data: 3.770 [95.76] .074 .523 Dia. [1.88] [13.28] .225 [5.72] Thru Hole .170 [4.32] 3.585 [91.06] Connectors used with—page 65 .137 [3.48] .074 [1.88] Dia. x .175 [4.45] Deep Technical Documents: (pages 186, 187): Instruction Sheets 408-7498, 408-7506 Single Slotted Card Guide and Connector Mounting .100 [2.54] Contact Centerline Connector Centerline .091 [2.31] Dia. A .200 [5.08] .035 Dia. [0.89] Mounting Hole E Min. .225 [5.72] Dimensions A E .100 .263 2.54 6.68 .125 .288 3.18 7.31 .150 .313 3.81 7.95 .156 .319 3.96 8.10 70 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors (Continued) Double Slotted Without Stand-off Card Guides (Continued) 1.680 [42.67] .080 [2.03] Material: Nylon, natural 1.500 [38.10] .150 [3.81] .540 [13.72] Part No. 583425-1 Related Product Data: Connectors used with—page 65 .300 [7.62] .400 [10.16] Technical Documents: (pages 186, 187): Instruction Sheets 408-7498, 408-7506 Double Slotted Card Guide and Connector Mounting .100 [2.54] Contact Centerline Connector Centerline .310 [7.87] .175 [4.45] A .200 [5.08] .035 Dia. [0.89] Mounting Hole E Min. Dimensions A E .100 .328 2.54 8.33 .125 .353 3.18 8.96 .150 .376 3.81 9.60 .156 .384 3.96 9.75 Note: Mother Board must be .063 [1.59] thick for use with Double Slotted Card Guides. Recommended PC Board Layout for Connectors With End Caps Contact Centerline .100 [2.54] .200 [5.08] .100 [2.54] Dia. Connector Centerline .035 Dia. [0.89] Mounting Hole A E Dimensions A E .100 .267 2.54 6.78 .125 .317 3.18 8.05 .150 .367 3.81 9.32 .156 .379 3.96 9.62 71 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Twin Leaf Mother Board Connectors (Continued) Keying Plugs Material: Nylon, natural Technical Documents: (pages 186, 187): Instruction Sheet 408-7479 Type A Type B Intercontact In-Row Contact Spacing Type of Contact .100 2.54 Solder Post Card Extender Solder Post Card Extender Solder Post Wrap-Type Post Card Extender Solder Post Wrap-Type Post Card Extender .125 3.18 .150 3.81 .156 3.96 Connector Style* with without End Caps End Caps 583715 583485 530268 530291 583679 583533 530265 530290 583692 583407 583754 583752 530278 530270 583660 583486 583755 583753 530267 530282 Type A Part Numbers On-Contact Intercontact Keying Plug Type B Insertion/Extraction Part Numbers Tool On-Contact Keying Plug Part Insertion/Extraction Numbers Tool 530286-3 — 91081-2 583714-1 91088-1 530286-2 530030-1 91081-1 583714-1 91088-1 530286-2 530030-1 91081-1 — — 530286-2 530030-1 91081-1 — — *Refer to pages 66-68, as applicable, for specific connector sizes. Dimension A Connector Centerlines Intercontact On-Contact .100 .040 .129 2.54 1.02 3.28 .125 .050 .129 3.18 1.27 3.28 .150 .050 .160 3.81 1.27 4.06 .156 .050 .160 3.96 1.27 4.06 A .475 [12.06] Min. Recommended PC Board Cutout for Keying Plugs Other Twin Leaf Mother Board Connectors Card Extender Connectors .400 [10.16] For more information on the connectors shown here, consult Tyco Electronics. Fits for .055-.070 [1.4-1.78] PCBoard Connectors With End Caps .225 [5.72] .610 [15.49] Centerlines Part Number Series* .150 3.81 .156 3.96 530278 530267 *Consult Tyco Electronicsfor specific connector sizes. 72 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors Product Facts ■ Zero insertion force; little or no effort required to insert and withdraw PC boards ■ Reduced pad wear for extended board life ■ Allows all four sides of board to be used for input/output functions ■ Accepts double-sided boards ■ Three contact styles to choose from: vertical solder post, right-angle solder post and wrap-type post (2 and 3 high) ■ Available in .100 [2.54], .125 [3.18] and .156 [3.96] centerlines ■ Three configurations available: open one end, open both ends and closed both ends ■ Products indicated are recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Performance Specifications Current vs. Temperature Rise*: 3 amperes at 30°C Operating Temperature: –55°C to +105°C Contact Resistance: 20 milliohms max. Durability: Tested to 5000 cycles AMP Rotary Cam Zero Insertion Force (ZIF) Card Edge Connectors are available in sizes to fit most industry-standard printed circuit boards. A clockwise rotation of the cam handle opens contacts to allow zero-force insertion or removal of PC boards— even boards with a large number of contacts. Turning the cam handle to close the connector locks the board securely in place. Rotary Cam ZIF Connectors accept double-sided PC boards .054-.070 [1.37- 1.78] thick, with contact centerline intervals of .100 [2.54], .125 [3.18] and .156 [3.96]. Row-to-row spacing of connector posts is .200 [5.08] for .100 [2.54] and .156 [3.96] connectors and .250 [6.35] for .125 [3.18] connectors. Contacts are nickel underplated phosphor bronze with gold plate in the contact area and tin-lead plated posts. Contact configurations include vertical and right-angle solder posts and wrap-type posts. Preassembled connectors feature housings made from 94V-0 rated glass-filled polyester and mounting ears for easy mounting to the mother board. Housings are available with one end open, both ends open and both ends closed for side and top daughter board insertion. Integral board locks secure boards in the connectors. Accessories include dust covers, cam rods (with and without boots) and cam keys for nut-driver actuation and for tandem operation of connectors. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 73 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End .440 [11.18] .370 [9.40] Related Product Data: Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 B Closed Position .150 [3.81] .250 [6.35] 1.095 [27.81] Ref. .850 [21.60] .050 [1.27] Technical Documents: (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 .210 [5.33] .100 [2.54] Typ. A D C No. of Dual Positions A B 22 2.100 53.34 2.800 71.12 25 2.400 60.96 28 2.700 68.58 3.000 76.20 31 Dimensions C .125 .160 .125 .160 Closed Both Ends 1-531019-1 — 1-531019-2 — 2.900 73.66 3.200 81.28 .160 21-531020-3 — — .160 2-531020-1 — — .125 .160 .125 .160 .125 3-531020-2 1-531020-4 1-531020-5 1-531020-5 3-531020-3 1-531020-7 22-531020-82 1-531020-8 1-531020-8 22-531020-92 — — — — — — — 531021-8 — — 1-531019-4 — — — — — — — 1-531019-8 — .160 1-531020-9 1-531021-9 1-531019-9 .125 1-531020-0 2-531020-0 23-531020-02 — — — — — — 3.100 78.74 2.300 58.42 3.100 78.74 3.400 86.36 2.600 66.04 3.400 86.36 3.700 93.98 3.700 93.98 4.000 101.60 4.200 106.68 4.500 114.30 3.700 93.98 40 3.900 99.06 4.600 116.84 4.900 124.46 4.100 104.14 43 4.200 106.68 4.900 124.46 5.200 132.08 4.400 111.76 50 4.900 124.46 5.600 142.24 5.900 149.86 5.100 129.54 60 5.900 149.86 6.600 167.64 6.900 175.26 6.100 154.94 7.100 180.34 7.400 187.96 .200 [5.08] Part Numbers Open Both Ends1 — — — — E* 3.500 88.90 6.400 162.56 .018 [0.46] Typ. E Open One End1 1-531020-1 1-531020-1 1-531020-2 1-531020-2 D 36 65 .025 [0.64] Typ. 6.600 167.64 .160 .125 .160 .160 *Metric equivalents in millimeters for post lengths E are .125 = [3.18]; .160 = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. 2Connectors without cam rod and boardlock. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 74 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued) Right-Angle Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—page 82, 96 .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End .440 [11.18] .370 [9.40] B Closed Position .150 [3.81] Technical Documents: (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 .250 [6.35] 1.095 [27.81] Ref. .160 [4.06] .050 [1.27] .850 [21.60] .025 [0.64] Typ. .210 [5.33] .100 [2.54] Typ. A .025 [0.64] Typ. D .200 [5.08] .100 [2.54] C Bend Right Shown No. of Dual Positions 25 36 50 65 A 2.400 60.96 3.500 88.90 4.900 124.56 6.400 162.56 Dimensions B C 3.100 78.74 4.200 106.68 5.600 142.24 7.100 180.34 D 3.400 86.36 4.500 114.30 5.900 149.86 7.400 187.96 2.800 71.12 3.700 93.98 5.100 129.54 6.600 167.64 Bend Right Part Numbers (Open End1) R 1-531395-23 R 1-531396-4 L 1-531396-8 R 1-531396-0 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown. 2. Other connector sizes can be made available, consult Tyco Electronics. 3. Open both ends. 75 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued) Vertical Connector, Wrap-Type Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 .370 [9.40] .440 [11.18] B Closed Position .150 [3.81] .250 [6.35] Technical Documents: (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 1.095 [27.81] Ref. .050 [1.27] .850 [21.60] .025 [0.64] Typ. .100 [2.54] Typ. .210 [5.33] A E .025 [0.64] Typ. .200 [5.08] D C No. of Dual Positions A 25 2.400 60.96 Part Numbers Open Open One End1 Both Ends1 B Dimensions C D E* 3.100 78.74 3.400 86.36 2.600 66.04 .380 1-531414-2 — 1-531414-4 1-531414-4 1-531415-4 — 36 3.500 88.90 4.200 106.68 4.500 114.30 3.700 93.98 .580 .380 40 3.900 99.06 4.100 104.14 4.900 124.46 5.900 149.86 6.400 162.56 4.600 116.84 4.800 121.92 5.600 142.24 6.600 167.64 7.100 180.34 4.900 124.46 5.100 129.54 5.900 149.86 6.900 175.26 7.400 187.96 4.100 104.14 4.300 109.22 5.100 129.54 6.100 154.94 6.600 167.64 .580 1-531414-5 — .380 1-531414-6 — .580 2-531414-4 1-531415-8 .580 1-531414-9 — .580 1-531414-0 — 42 50 60 65 *Metric equivalents in millimeters for post lengths E are .580 = [14.73] (3-high wrap-type); .380 = [9.65] (2-high wrap-type). 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 76 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .125 x .250 [3.18 x 6.35] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End .440 [11.18] .370 [9.40] B Closed Position .150 [3.81] Technical Documents: (pages 186,187): Product Specification 108-9048 Instruction Sheet 408-7911 .250 [6.35] 1.095 [27.81] Ref. .850 [21.60] .210 [5.33] .125 [3.18] Typ. A D C .050 [1.27] .025 [0.64] Typ. .018 [0.46] Typ. E .250 [6.35] Part Numbers Open Open One End1 Both Ends1 No. of Dual Positions A B Dimensions C D E* 28 3.375 85.73 4.125 104.76 4.425 112.40 3.625 92.08 .125 — 1-531024-3 30 3.625 92.08 4.375 111.13 4.675 118.75 3.875 98.43 .125 1-531023-4 — 40 4.875 123.83 5.625 142.88 5.925 150.50 5.125 130.18 .160 1-531023-4 1-531024-4 *Metric equivalents in millimeters for post lengths E are .125 = [3.18]; .160 = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 77 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Rotary Cam ZIF Connectors, .156 x .200 [3.96 x 5.08] Centerline Vertical Connector, Solder Post Terminals Material and Finish: Housing—Glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold per MIL-G45204 in contact area; .000100 [0.00254] tin-lead per MIL-P-81728 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: .130 [3.3] Dia. Holes .250 [6.35] Dia. C’Bore .080 [2.03] Deep Closed End Board Lock Feature—On connectors open one end and open both ends Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 73 Dust Cover—page 79 PC Board Hole Layout and Edge Patterns—pages 81, 82 Special Application—pages 82, 96 .440 [11.18] .370 [9.40] B Closed Position .150 [3.81] Technical Documents: .250 [6.35] (pages 186, 187): Product Specification 108-9048 Instruction Sheet 408-7911 1.095 [27.81] Ref. .850 [21.60] .210 [5.33] .156 [3.96] Typ. A D C No. of Dual Positions A B 22 3.276 83.21 4.088 103.83 36 5.460 138.68 43 6.552 166.42 Dimensions C .050 [1.27] .025 [0.64] Typ. E .018 [0.46] Typ. .200 [5.08] Part Numbers Open Both Ends1 — — Closed Both Ends — 531007-9 D E* 4.388 111.46 3.588 91.14 .125 .160 Open One End1 531025-3 531025-9 6.272 159.31 6.572 166.93 5.772 146.61 .160 — 1-531026-1 — 7.364 187.05 7.664 194.67 6.864 174.35 .125 531025-6 — — *Metric equivalents in millimeters for post lengths E are .125 = [3.18]; .160 = [4.06]. 1Recognized under the Component Program of Underwriters Laboratories Inc. Notes: 1. Connector with card slot open one end is shown for illustration purposes. 2. Other connector sizes can be made available, consult Tyco Electronics. 78 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Accessories Dust Covers A Material: Rigid vinyl, black Dimension A 11.050 280.67 48.000 1219.20 Part Numbers 531863-2 531863-1 Note: Other lengths can be made available upon request, consult Tyco Electronics. .348 [8.84] Cam Rods with Boot Material: Cam Rod—Stainless steel Boot—Glass-filled polyester, yellow .654 [16.61] .835 [21.21] .200 [5.08] .200 [5.08] Dimension A 3.185 80.90 3.705 94.11 4.470 113.54 5.285 134.24 5.900 149.86 5.975 151.77 Part Numbers 650083-1 650083-2 650083-3 650083-4 650083-6 532563-7 .400 [10.16] Dimension A 6.385 162.18 6.985 177.42 7.485 190.12 7.725 196.22 8.320 211.34 A Part Numbers 650083-7 650083-8 650083-9 1-532563-0 1-650083-7 Note: Other lengths can be made available upon request, consult Tyco Electronics. 79 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Accessories (Continued) Cam Rods without Boot .125 [3.18] Material: Stainless steel .775 [19.69] .200 [5.08] .055 [1.40] .045 [1.14] A Dimension A 2.200 55.88 2.700 68.58 3.300 83.82 4.750 120.65 5.000 127.00 5.500 139.70 Dimension A 6.000 152.40 6.250 158.75 6.750 171.45 8.250 209.55 12.500 317.50 Part Numbers 2-531004-8 2-531004-9 3-531004-0 2-531004-4 1-531004-4 2-531004-6 Part Numbers 2-531004-7 1-531004-6 1-531004-7 3-531004-2 2-531004-0 Note: Other lengths can be made available upon request, consult Tyco Electronics. .125 [3.18] .252 [6.40] .055 [1.40] .260 [6.60] .045 [1.14] A Dimension A 3.380 85.85 4.50 114.30 5.200 132.08 6.90 175.30 13.120 333.25 Part Numbers 645293-3 645293-8 645293-6 645293-7 645293-5 Note: Other lengths can be made available upon request, consult Tyco Electronics. 80 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Recommended PC Board Hole Layouts Mother Board Hole Layout, Vertical Through-Board Connectors .048 Dia. Typ. [1.22] .128 Dia. [3.25] (2 Plc.) W CL A* X B* *Refer to individual connector specifications. CL W X .100 2.54 .125 2.18 .156 3.96 .200 5.08 .250 6.35 .200 5.08 .350 8.89 .375 9.53 .406 10.31 Mother Board Hole Layout, Right-Angle Through-Board Connectors .100 Typ. [2.54] .200 [5.08] .048 Dia. Typ. [1.22] Pin No. 1 (Ref.) .400 Max. [10.16] A* PCBoard Edge *Refer to individual connector specifications. 81 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Recommended PC Board Edge Pattern Daughter Board Edge Pattern .700 [17.78] Min. .270 [6.86] Min. CL C CL Minus .006 [0.15] +.005 -.000 [+0.13] A ±.005 B [±0.13] CL = .100 [2.54] C = .050 [1.27] A B 2.100 2.288 53.34 58.12 2.400 2.588 60.96 65.74 2.700 2.888 68.58 73.36 No. of Dual Positions 22 25 28 30 — — 31 3.000 76.20 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 6.400 162.56 3.188 80.98 3.688 93.68 4.088 103.84 4.388 111.46 5.088 129.24 6.088 154.64 6.588 167.34 36 40 43 50 60 65 Special Application CL = .125 [3.18] C = .078 [1.98] A B — CL = .156 [3.96] C = .094 [2.39] A B 3.267 3.576 83.21 90.83 — — — — — 3.375 85.73 3.625 92.08 3.613 91.77 3.863 98.12 — — — — — — — — — — 5.460 138.68 5.760 146.30 4.875 123.83 5.113 129.87 — — — — 6.552 166.42 6.852 174.04 — — — — — — — — — — — — Tandem Application Special Rod (Part No. Series 645293) Allows Customer Supplied Nut Driver Actuation (Refer to page 80.) Note: Contact Tyco Electronics for information concerning special tandem connectors. 82 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors Product Facts ■ Minimizes force needed to install and remove printed circuit boards ■ Available in lever and bell crank styles ■ Lever styles allow side and top card entry ■ Wiping action contacts enhance electrical properties ■ Contacts on .100 x .100 [2.54 x 2.54] or .125 x .125 [3.18 x 3.18] centers ■ .025 [0.64] square posts ■ Accepts PC boards from .054 to .070 [1.37 to 1.78] in thickness ■ Normally closed design leaves springs in relaxed position ■ 50 to 175 dual positions available on .100 [2.54] centerline connectors and 40 to 140 dual positions available on .125 [3.18] centerline connectors Performance Specifications Current vs. Temperature Rise*: 3 amperes at 30°C Operating Temperature: –65°C to +85°C Contact Resistance: 16 milliohms max. Durability: Tested to 250 cycles (board-to-contact actuation) *Consult Tyco Electronicsengineering when paralleling contacts for power applications. AMP Linear Zero Insertion Force (ZIF) PC Board Edge Connectors are available in both lever and bell crank actuated styles and can be provided as panel assemblies, separate housings and contacts or as preassembled with solder post terminals. Panel assemblies include a housing with ACTION PIN press-fit solderless contacts mounted on an epoxy board for rack application. Separate housing assemblies and ACTION PIN contacts allow customer assembly. These can be mounted as close as .625 [15.88]. More design latitude for high density application is provided by the side entry lever-type connector, permitting use of all sides of the PC board for edge-type I/O connections (see page 133). Where solder applications are required, Tyco Electronics has a line of preassembled connectors with tin-plated solder terminals. All these configurations are available in a broad range of sizes. and housing modules without removing the entire housing assembly from the board. With ZIF style connectors, intermittencies can occur if a contact comes to rest on a piece of foreign matter (dust and dirt particles) found on PC boards. To decrease the probability of this happening, all connectors have been designed to include a wiping contact which produces a wiping action. This action, produced by the geometry and bending movements of the beam, pushes aside debris and allows for good electrical connection by cleaning the actual point of contact. In addition, all connectors have removable wings which make it possible to repair or replace damaged cam rails, handles, contacts 83 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline Housing with Solder Posts Lever Style, Side Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] min. gold per MIL-G-45204 in contact area; .000100 [0.00254] min. tin-lead on post with entire contact underplated .000050 [0.00127] min. nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 Special Application—page 96 Technical Documents: (pages 186, 187): Product Specification 108-14015 Application Specification 114-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 .450 [11.43] A .500 [12.70] Max. B C L Last Contact Position .355 [9.02]* Closed .103 [2.62] Closed End C Open End Open .845 [21.46] .600 [15.24] C L First Contact Position P .100 Typ. [2.54] Mounting Hole C L .100 [2.54] .190 [4.83] P .845 [21.46] .175 [4.45] .206 [5.23] Mounting Hole CL 1.075 [27.31] Section P-P *Card slot depth. No. of Dual Positions 35 80 100 A Dimensions B C 6.113 155.27 11.613 294.97 13.613 345.77 3.400 86.36 7.900 200.66 9.900 251.46 2.000 50.80 3.000 76.20 3.000 76.20 Part Number 1-645135-2 1-645135-1 1-645135-5 Note: Other connector sizes can be made available, consult Tyco Electronics. 84 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Panel Assembly Lever Style, Side Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 ACTION PIN Contacts— pages 88, 94 Tooling—page 95 Special Application—page 96 .343 [8.71] Max. PC Board Channel .355 [9.02] Card Slot Depth Open End Closed End C Technical Documents: 1.555 [39.50] (pages 186, 187): Product Specification 108-14015 Application Specification 114-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 .125 [3.18] D 1.425 [36.16] .150 [3.81] Countersunk Hole (2 Plcs.) .812 [20.62] A .100 [2.54] Typ. .100 [2.54] .750 [19.05] B No. of Dual Positions 75 100 130 140 150 160 160 Dimensions A B C D 7.400 251.46 9.900 251.46 12.900 251.46 13.900 353.06 14.900 251.46 15.900 403.86 15.900 403.86 10.125 320.68 12.625 320.68 15.625 320.68 16.625 422.28 17.625 320.68 18.625 473.07 18.625 473.07 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 .615 15.62 .615 15.62 .615 15.62 .615 15.62 .615 15.62 .615 15.62 .455 11.56 Part Numbers 1-645145-0 1-645145-5 2-645145-1 2-645145-3 2-645145-5 2-645145-7 147400-1 Note: Other connector sizes can be made available, consult Tyco Electronics. 85 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Panel Assembly Lever Style, Top Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 ACTION PIN Contacts— pages 88, 94 Tooling—page 95 .343 [8.71] Max. PC Board Channel .355 [9.02] Card Slot Depth Technical Documents: (pages 186, 187): Closed End Product Specifications 108-14015, 108-26003 Application Specification 114-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 Closed End C 1.555 [39.50] .125 [3.18] .615 [15.62] 1.425 [36.16] .150 [3.81] Countersunk Hole (2 Plcs.) .812 [20.62] A .100 [2.54] Typ. .100 [2.54] .750 [19.05] B No. of Dual Positions 110 120 A Dimensions B C 10.900 276.86 11.900 302.26 13.625 346.08 14.625 371.48 3.000 76.20 3.000 76.20 Part Numbers 1-645147-7 1-645147-9 Note: Other connector sizes can be made available, consult Tyco Electronics. 86 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Housing Lever Style, Side Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Mounting Screws—Customer supplies, must be applied before opening connector Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 88 ACTION PIN Contacts— pages 88, 94 Tooling—page 95 Special Application—page 96 A Ref. Technical Documents: (pages 186, 187): B Product Specifications 108-14015, 108-26003 Application Specification 108-26003 Instruction Sheets 408-2995, 408-2999, 408-6915 C L Last Contact Position Closed C L First Contact Position Open End C Open Closed End P .450 [11.43] P Mounting Hole C L .355 [9.02]* .815 [20.70] .206 [5.23] .600 [15.24] No. of Dual Positions A 7.613 4.900 193.37 124.46 11.113 7.400 75 282.27 187.96 11.613 7.900 80 294.97 200.66 13.613 9.900 100 345.77 251.46 14.613 10.900 110 371.17 276.86 15.113 11.400 115 383.87 289.56 16.113 12.400 125 409.27 314.96 16.613 12.900 130 421.97 327.66 17.613 13.900 140 447.37 353.06 19.613 15.900 160 498.17 403.86 21.113 17.400 175 536.27 441.96 Note: Other connector sizes can be made available, consult Tyco Electronics. 50 Section P-P *Card slot depth. Dimensions B Part Numbers C 2.000 50.80 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 1-645115-5 1-645115-0 1-645115-1 1-645115-5 1-645115-7 3-645115-2 1-645115-8 2-645115-0 2-645115-1 2-645115-3 3-645115-3 3-645115-0 87 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) ACTION PIN Contacts with Wiping Feature, .100 [2.54] Centerline Recommended PC Board Hole Layout and Edge Pattern, .100 [2.54] Centerline Material and Finish: Related Product Data: Mother Board Hole Layout Copper alloy 725, plated .000015 [0.00038] gold per MIL-G-45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G-45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Performance Specifications— page 83 ACTION PIN Contact Description and Application Specification— page 94 Tooling—page 95 .047 Dia. Typ. [1.19] (Solder Post Only)* .120 Dia. [3.05] CL Technical Documents: C B (pages 186, 187): *For ACTION PIN post hole diameter, see page 94. Instruction Sheet 408-2665 Connector Style CL Lever .100 2.54 A (Comb) Dimensions A B .100 .206 2.54 5.23 C .175 4.45 .045 [1.14] Contact Area Prenotched for Breakoff at Assembly Daughter Board Edge Pattern .745 [18.92] .200 Min. [5.08] .600 Ref. [15.24] 1.485 [37.72] B Min. Prenotched for Breakoff at Assembly .098 Typ. [2.49] A Max. .100 [2.54] .070 [1.78] .100 [2.54] .740 [18.80] Post Area .100 (No. of Pos. –1) +.196 [2.54 (No. of Pos. –1) +4.98] .025 Sq. [0.64] Contact Combs Number of Contacts Per Comb* Dimension A 55 5.400 137.16 Part Number Connector Style 4-119311-1 *At least two (2) contact combs required per housing. Note: Other sizes can be made available, consult Tyco Electronics. Entry Style Side Lever Top Dimensions A .240 6.10 .240 6.10 B — .320 8.13 Reeled Contacts Number of Contacts Per Reel 35,000 Part Number 119196-6 Note: Other plating combinations and thicknesses can be made available, consult Tyco Electronics. 88 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline Panel Assembly Lever Style, Side Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Special Application—page 96 PC Board Channel .343 Max. [8.71] Technical Documents: .355 [9.02] Card Slot Depth Open End (pages 186, 187): Closed End C Instruction Sheets 408-2995, 408-6915, 408-6916 .615 [15.62] .125 [3.18] 1.425 [36.16] .150 [3.81] Countersunk Hole (2 Plcs.) .812 [20.62] A .125 Typ. [3.18] 1.555 [39.50] .125 [3.18] .750 [19.05] B No. of Dual Positions 40 56 60 72 84 124 A Dimensions B C 4.875 123.83 6.875 174.63 7.375 187.32 8.875 225.43 10.375 250.83 15.375 390.53 7.625 193.68 9.625 244.48 10.125 257.17 11.625 295.28 13.125 320.68 18.125 460.38 2.000 50.80 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 Part Numbers 1-645146-5 1-645146-9 1-645146-0 1-645146-3 1-645146-6 2-645146-6 Note: Other connector sizes can be made available, consult Tyco Electronics. 89 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) Panel Assembly Bell Crank Style, Top Entry Material and Finish: Housing—Glass-filled polyester, black Contacts—Copper alloy 725, plated .000015 [0.00038] gold per MIL-G45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Technical Documents: .935 Max. [23.75] (pages 186, 187): .355 [9.02] Card Slot Depth Instruction Sheets 408-2995, 408-6915, 408-6916 3.620 Ref. [91.95] (Open) Closed End 1.555 [39.50] .125 [3.18] .615 [15.62] 2.41 [54.38] .609 [15.47] A .125 [3.18] .125 Typ. [3.18] .750 [19.05] B No. of Dual Positions 60 80 112 140 Dimensions A B 7.375 187.33 9.875 250.82 13.875 352.43 17.375 441.33 10.625 269.88 13.125 333.38 17.125 434.98 20.625 523.88 Part Numbers 1-645149-0 1-645149-5 2-645149-3 3-645149-0 Note: Other connector sizes can be made available, consult Tyco Electronics. 90 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) Housing Lever Style, Side Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Mounting Screws—Customer supplied, must be applied before opening connector Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Special Application—page 96 Technical Documents: (pages 186, 187): Instruction Sheets 408-2995, 408-6915, 408-6916 .475 [12.07] A Ref. .355 [9.02]* B .815 [20.7] CL First Contact Position Closed .600 [15.24] CL Last Contact Position Open End C Open 1.087 [27.61] Section P-P No. of Dual Positions 84 100 112 124 .115 [2.92] P .218 [5.54] Mounting Hole CL *Card slot depth. Closed End P Mounting Hole CL A Dimensions B C 14.112 358.44 16.112 409.24 17.612 447.34 19.112 485.44 10.375 263.52 12.375 314.33 15.775 400.68 17.275 438.78 3.000 76.20 3.000 76.20 3.000 76.20 3.000 76.20 Part Number 1-645116-6 2-645116-0 2-645116-3 2-645116-6 Note: Other connector sizes can be made available, consult Tyco Electronics. 91 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) Housing Bell Crank Style, Top Entry Material: Glass-filled polyester, black Related Product Data: Daughter PC Board—.054-.070 [1.37-1.78] thick Mounting Screws—Customer supplied, must be applied before opening connector Performance Specifications— page 83 PC Board Hole Layout and Edge Pattern—page 93 ACTION PIN Contacts— pages 93, 94 Tooling—page 95 Technical Documents: (pages 186, 187): Instruction Sheets 408-2995, 408-6915, 408-6916 .475 [12.07] A Ref. 1.062 [26.97] (Open) 1.874 [47.60] .312 [7.92] B CL Last Contact Position CL First Contact Position .500 [12.70] .355 [9.02]* Closed End .815 [20.7] .600 [15.24] .115 [2.92] 2.562 [65.07] (Closed) P .115 [2.92] 1.820 [46.23] Mounting Hole CL P 1.250 [31.75] Mounting Hole CL .187 [4.75] Section P-P *Card slot depth. No. of Dual Positions 52 60 80 112 Dimensions A B 8.562 217.47 9.562 242.87 13.125 333.37 16.062 407.97 6.375 161.93 7.375 187.32 9.875 250.82 13.875 352.43 Part Numbers 1-645142-8 1-645142-0 1-645142-5 2-645142-3 Note: Other connector sizes can be made available, consult Tyco Electronics. 92 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued) ACTION PIN Contacts with Wiping Feature, .125 [3.18] Centerline Recommended PC Board Hole Layout and Edge Pattern, .125 [3.18] Centerline Material and Finish: Related Product Data: Copper alloy 725, plated .000015 [0.00038] gold per MIL-G-45204 in contact area; .000001 [0.00003] min. gold flash per MIL-G-45204 on post with entire contact underplated .000050 [0.00127] nickel per QQ-N-290 Performance Specifications— page 83 ACTION PIN Contact Description and Application Specification— page 94 Tooling—page 95 Mother Board Hole Layout .047 Dia. Typ. [1.19] (Solder Post Only)* .120 Dia. [3.05] CL Technical Documents: C B (pages 186, 187): *For ACTION PIN post hole diameter, see page 94. Instruction Sheet 408-2665 Connector Style Lever A (Comb) Bell-Crank .045 [1.14] Contact Area Dimensions A B .125 .218 3.18 5.54 .125 1.250 3.18 31.75 CL .125 3.18 .125 3.18 C .187 4.75 .187 4.75 Prenotched for Breakoff at Assembly Daughter Board Edge Pattern .750 [19.05] .600 Ref. [15.24] 1.490 [37.85] .200 Min. [5.08] B Min. .740 [18.80] Post Area .125 [3.18] .110 Typ. [2.79] .025 Sq. [0.64] .125 [3.18] A Max. .090 Typ. [1.78] .125 (No. of Pos. –1) +.220 [3.18 (No. of Pos. –1) +5.59] Contact Combs Number of Contacts Per Comb* Dimension A 56 6.875 174.63 Part Number Connector Style Side 1-119950-2 *At least two (2) contact combs required per housing. Note: Other sizes can be made available, consult Tyco Electronics. Entry Style Lever Top Bell-Crank Top Dimensions A .240 6.10 .240 6.10 .775 19.68 B — .320 8.13 .600 15.24 93 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide break-through and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today’s standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. ➀ Annular Ring (See Note) ➁ Drilled Hole ➂ Copper Thickness ➃ Tin-Lead Thickness ➄ Plated Through-Hole ACTION PIN Contact/PC Board Applications Connector Type ACTION PIN Contact Material Thickness Drilled Hole Diameter➁ Linear ZIF .025 0.64 .0453±.001 1.151±0.03 Plating Thicknesses Copper➂* Tin-Lead➃ .001-.003 0.03-0.08 .0003 0.008 Min. Plated Through-Hole Diameter➄ .037-.043 0.94-1.09 Radial Hole Distortion Average Maximum Not Specified Not Specified *Maximum hardness of copper layer is 150 Knoop. Note: Recommended annular ring diameter is hole diameter plus .020 [0.51]. 94 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors (Continued) Assembly tooling is not required except when using connectors with ACTION PIN contacts. ACTION PIN contact assembly requires an arbor-style bench tool with a capacity of 40 lb [178 N] per contact, a support fixture, contact applicator, carrier removal tool and housing assembly tool. Tooling Typical procedure is to place a PC board on the support fixture, insert contact combs into the printed circuit board with the contact applicator and seat with the arbor tool. Next, remove the carrier strip from the contact combs with the carrier break-off tool. Place the housing over the contacts with the housing assembly tool, and repeat the entire process until the board is complete. .100 x .100 [2.54 x 2.54] Centerline Connectors No. of Dual Positions 50 80 100 110 115 120 125 140 175 T-Bar Applicator 266267-4 266267-3 266267-4 266267-5 266267-5 266267-5 266267-4 266267-4 266267-5 Carrier Removal Tool 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 265924-4 Housing Assembly Tool 313136-1 313136-2 Housing Removal Tool Wing Removal/ Replacement Tool Housing Insertion Tool 313256-1 266233-1 266264-1 Housing Removal Tool Wing Removal/ Replacement Tool Housing Insertion Tool 313256-1 266233-1 266264-1 Contact Replacement Tools With Housing Without Housing 313136-3 266235-1 3-265871-2 313136-4 313136-5 .125 x .125 [3.18 x 3.18] Centerline Connectors No. of Dual Positions 40 52 56 60 72 84 112 124 140 T-Bar Applicator 313139-1 313139-2 313139-2 313139-2 313139-3 313139-2 313139-2 313139-2 313139-2 Carrier Removal Tool 265924-4 265924-6 265924-6 265924-7 265924-4 265924-5 265924-7 265924-5 265924-5 Housing Assembly Tool 313136-1 Contact Replacement Tools With Housing Without Housing 313136-2 313136-3 266235-1 3-265871-2 313136-4 313136-5 95 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) Linear ZIF Connectors (Continued) Special Application Use Linear and Rotary ZIF Connectors as Card Guides to access more sides of the Daughter Board. Standard Edge II (pages 15 thru 27) or AMP PACE Connectors (pages 98 thru 115) 96 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) ACTION PIN Press-Fit Contacts The Reliable Plated ThroughHole Interconnect Solderless interconnections have been popular in electrical and electronic application with world-wide success for decades. They provide reliable electrical and mechanical stability and offer applied-cost savings across the board. For PC board applications, ACTION PIN contacts from Tyco Electronics provide these features: n Large gas-tight contact zone n Reliability due to stored energy in compliant pin contacts n No damage to plated through-holes during installation • Solder spots; short circuits between printed circuits Principle of the Tyco Electronics Compliant ACTION PIN Contact n Especially suited for multilayer PC boards • Flux residuals When an ACTION PIN contact is inserted into a plated through-hole, two spring members are compressed, exerting force against the hole for gas-tight connection. The diameter of the hole is smaller than the diagonal size of the pin (see cross-section illustration below). n Less costly board manufacturing due to larger hole tolerances compared to use of solid pins n Application can be made by end-user n Repairability—contact can be replaced in the same pin location (two repairs) n Installation with no heat cycling of board n Permits mass insertion by minimizing forces needed to insert pins as compared to solid pin press-fit application n Significant applied-cost savings in many applications Since ACTION PIN contacts do not have to be soldered, issues associated with solder are eliminated, such as: • Faulty solder joints • Solder fumes; contaminant’s are deposited on the contacts • Thermal strain on printed circuit boards and components • Degasing of plated through-holes Solderless press-fit interconnections using the ACTION PIN contact are primarily integrated in, but not limited to, backplanes. Solderless press-fit interconnections are used in racks, especially where connectors must be fixed on the solder side of the PC board and/or component side. In these applications, the holes for ACTION PIN contact connectors are covered during the soldering process and press-fitting is performed after soldering. Other applications for ACTION PIN contact interconnections include PC boards that incorporate components using surface mount technology (SMT). Here, too, press-fit interconnections can be applied after soldering, thus eliminating complications associated with connectors suitable for surface mounting. The beam characteristics of the pin are designed so that a plastic, as well as an elastic, deformation takes place during insertion. The two spring members compress to different degrees Minimum Hole Dia. .037 [0.94] to accommodate hole tolerances. The compliant pin also reduces strain on the board. With a rigid pin, the elastic strain energy is stored entirely in the board, leading to damage of the plated through-holes. With the ACTION PIN contact, the residual force of the elastic deformation maintains stored energy to produce a tight contact zone between the pin and the plated through-hole. This provides long term electrical and mechanical reliability of the interconnection. Maximum Hole Dia. .043 [1.09] Cross-Section Area from Tyco Electronics ACTION PIN Press-Fit Contact in Printed Circuit Board Holes from Tyco Electronics. Note: ACTION PIN contact mounting hole specifications are presented in each product section, where applicable. 97 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors Performance Specifications Electrical Characteristics Contact Resistance: ACTION PIN Contact Interface—5 milliohm Spring Contact to Test Board—11.5 milliohms Total Circuit Resistance: 12 milliohms Continuous Current Rating*: 3 amperes Insulation Resistance: 5,000 milliohms Dielectric Withstanding Voltage: .100 [2.54] Centerline Spacing— 1,000 VAC at sea level; 350 VAC at 50,000 ft. [15,240 m]; 275 VAC at 70,000 ft. [21,336 m] .125 [3.18] Centerline Spacing— 1,500 VAC at sea level; 500 VAC at 50,000 ft. [15,240 m]; 235 VAC at 70,000 ft. [21,336 m] Physical Characteristics Card Insertion Force (Max.): 16 oz [4.45 N] per contact pair ACTION PIN Contact Post Card Extraction Force (Min.): 1 oz [.278 N] per contact pair ACTION PIN Contact Post Retention (in PC board): .100 x .100 [2.54 x 2.54]— 7.5 lb. [33.4 N] min. Operating Temperature: –55°C to +85°C Durability: Tested to 100 cycles (100 insertions and withdrawals at a rate not exceeding 10 cycles per minute) Salt Spray: MIL-STD-1344, Method 1001 Physical Shock: MIL-STD-1344, Method 2004 Thermal Shock: MIL-STD-1344, Method 1003, Cond. A AMP PACE (Pre-Assembled Card Edge) Connectors are the latest innovation in the evolution of backplane architecture. Designed to shorten manufacturing time and reduce applied costs, these one-step, pre-assembled connectors are ready for mounting and mass insertion. In addition, design features such as removable housings and contacts, that Humidity: MIL-STD-1344, Method 1002, Type II are replaceable through the top of the connector housing, for maximum flexibility in your backplane packaging. At the heart of the AMP PACE Connector is AMP’s proven and reliable ACTION PIN Contact. This unique contact has superior electrical and physical characteristics that are top of the line in the industry. AMP PACE Connectors are available with post centerline spacings of: .100 x .100 [2.54 x 2.54] .100 x .200 [2.54 x 5.08] .125 x .125 [3.18 x 3.18] .125 x .250 [3.18 x 6.35] .156 x .200 [3.96 x 5.08] Important: Application tooling is absolutely necessary to insert connectors into PC boards. See page 115 for application tooling. Vibration: MIL-STD-1344, Method 2005 Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association, File No. LR7189 *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 98 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors (Continued) Product Facts Repairability— (See below for details) Individual contacts can be removed without removing the housing; housings can be removed without removing posts. Important: APC board must be inserted into the connector when removing the contact. Precision Plated Contacts— Selective plating puts gold where it is needed for superior electrical contact at a reasonable cost. Beam Contact Design— The contact’s unique beam design accommodates and compensates for daughter board warp and stress providing long-term, reliable performance (100 gram minimum normal force). Gas-Tight Connection— Spring sections of ACTION PIN Contacts compress in opposite directions, maintaining a gas-tight fit with the PC board. Contact Tip Alignment Strip— Polyester strip provides straight and stable pin alignment for damage-free entry into the PC board. Precision Plated Post— Gold plating can be applied to the entire post, or just the post tip for improved pluggability. Repairability Details Remove and replace contacts without removing housing. (See page 115 for Contact Replacement Tools.) Remove and replace housing without removing contacts. 99 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline Standard Housing .100 [2.54] .380 [9.65] .040 Min. [1.02] Contact Finish Area B C ±.006 [±0.15] .415 [10.54] Card Slot Depth .005/.007 [0.13/0.18] See E Below Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards Contact Tip Alignment Strip on .475 [12.07] Post Length .025 Sq. [0.64] Post .100 [2.54] A .100 [2.54] Typical Closed End/ Open End Housings .100 [2.54] Connectors can be mounted in pairs using any size combinations. Example: 1-30 pos. + 1-60 pos. = 1-90 pos. .135 [3.43] Detail E Keying Plugs On-Contact (Plastic) Part No. 119802-2 Intercontact (Plastic) Part No. 118982-1 100 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued) Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip—Clear polyester, type D Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. No. of Dual Positions A Dimensions B C 15 1.400 35.56 1.734 44.04 1.604 40.74 31 1.900 48.26 2.400 60.96 2.700 68.58 3.000 76.20 2.234 56.74 2.734 69.44 3.034 77.06 3.334 84.68 2.104 53.44 2.604 66.14 2.904 73.76 3.204 81.38 35 3.400 83.36 3.734 94.84 3.604 91.54 3.900 99.06 4.700 119.38 4.900 124.46 5.900 149.86 4.234 107.54 5.034 127.86 5.234 132.94 6.234 158.34 4.104 104.24 4.904 124.56 5.104 129.64 6.104 155.04 20 25 28 40 Related Product Data: Performance Specifications— page 98 Accessories—page 112 PC Board Edge Pattern—page 113 ACTION PIN Contact Mounting Hole Specifications—page 114 Application Tooling—page 115 Contact Replacement Tools— page 115 Special Application—page 96 48 50 60 Post Length .180 4.57 .475 12.07 .180 4.57 .180 4.57 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .180 4.57 .180 4.57 Closed/Closed Standard Scoop Closed/Open Standard 119734-1 119736-1 — 119237-1 — — 119734-6 — — 1-119734-1 — — 1-119734-4 — — 1-119237-7 — — 2-119734-1 — 119831-6 — — 119413-6 2-119734-6 2-119736-6 — 3-119237-4 — — 3-119734-6 — — 4-119734-6 4-119736-6 — Note: Other connector sizes and connectors with card scoops can be made available, consult Tyco Electronics. Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2978, 408-2979, 408-6881, 408-9091, 408-9188 101 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline Standard Housing .100 [2.54] .364 [9.24] .360 [9.14] B ±.006 [±0.15] C .005/.007 [0.13/0.18] .415 [10.54] Card Slot Depth See E Below Contact Tip Alignment Strip on .475 [12.07] and .702 [17.83] Post Lengths Accepts .054 to .071 [1.37 to 1.80] PC Boards .545 [13.84] .040 Min. [1.02] Contact Finish Area Post Length and Finish Area .025 Sq. [0.64] Post .093 Min. [2.36] .200 [5.08] A .100 [2.54] Housing with High Card Scoops .100 [2.54] .390 [9.91] B C ±.006 [±0.15] .005/.007 [0.13/0.18] .515 [13.08] Card Slot Depth See E Below Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards A Contact Tip Alignment Strip on .475 [12.07] and .702 [17.83] Post Lengths .364 [9.24] .040 Min. [1.02] Contact Finish Area .025 Sq. [0.64] Post .645 [16.38] .093 Min. [2.36] .200 [5.08] .100 [2.54] Keying Plugs Intercontact (Plastic) Part No. 118982-1 .135 [3.43] On-Contact (Plastic) Part No. 119802-2 Detail E 102 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued) Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip—Clear polyester, type D Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. No. of Dual Positions A Dimensions B C 20 .900 22.86 1.400 35.56 1.700 43.18 1.900 48.26 1.234 31.34 1.734 44.04 2.034 51.66 2.234 56.74 1.104 28.04 1.604 40.74 1.904 48.36 2.104 53.44 22 2.100 53.34 2.434 61.82 2.304 58.52 24 2.300 58.42 2.634 66.90 2.504 63.60 25 2.400 60.96 2.734 69.44 2.604 66.14 2.700 68.58 3.034 77.06 2.904 73.76 30 2.900 73.66 3.234 82.14 3.104 78.84 31 3.000 76.20 3.100 78.74 3.334 84.68 3.434 87.22 3.204 81.38 3.304 83.92 34 3.300 83.82 3.634 92.30 3.504 88.90 35 3.400 86.36 3.734 94.84 3.604 91.54 36 3.500 88.90 3.834 97.38 3.704 94.08 37 3.600 91.44 3.934 99.92 3.804 96.62 40 3.900 99.06 4.234 107.54 4.104 104.24 4.200 106.68 4.300 109.22 4.534 115.16 4.634 117.70 4.404 111.86 4.504 114.40 50 4.900 124.46 5.234 132.94 5.104 129.64 55 5.400 137.16 5.734 145.54 5.604 142.34 60 5.900 149.86 6.234 158.34 6.104 155.04 10 15 18 Related Product Data: Performance Specifications— page 98 Accessories—page 112 PC Board Edge Pattern—page 113 ACTION PIN Contact Mounting Hole Specifications—page 114 Application Tooling—page 115 Contact Replacement Tools— page 115 Special Application—page 96 Technical Documents: 28 32 (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2933, 408-2978, 408-2979, 408-9058, 408-9067, 408-9091, 408-9186 43 44 Post Length .180 4.57 .180 4.57 .180 4.57 .180 4.57 .180 4.57 1.475 12.07 .180 4.57 .180 4.57 .702 17.83 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .180 4.57 .180 4.57 .475 12.06 .475 12.06 .180 4.57 .475 12.06 .180 4.57 .180 4.57 .475 12.06 .180 4.57 .475 12.07 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .180 4.57 .702 17.83 Closed End/Closed End Standard High Scoop — 1-650297-1 1-119738-1 119791-1 1-119738-4 — 1-119738-6 — 1-119738-8 — -119216-8 650123-8 1-119738-0 — 1-119738-1 — 1-119163-1 — 1-119738-4 — 1-119216-4 — 1-119738-6 1-119791-6 1-119216-6 — 1-119163-6 — 1-119738-7 — 1-650122-8 — — 2-119791-0 2-119216-0 — 2-119216-1 — 2-119738-2 — 2-119216-2 — 2-650122-3 — 2-119738-6 — 2-119216-6 — 2-650122-9 — 3-119216-0 — 3-119738-6 3-119791-6 3-119216-6 — — 3-119726-6 4-119738-1 4-650124-1 4-119738-6 — 119677-1 — Note: Other connector sizes can be made available, consult Tyco Electronics. 103 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connectors, .125 x .125 [3.18 x 3.18] Centerline Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. palladiumnickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip—Clear polyester, type D Housing with High Card Scoops 28 Dual Positions Part Number 1-119853-4 3.625±.006 [92.08±0.15] .005/.007 [0.13/0.18] Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. .515 [13.08] Card Slot Depth .702 [17.83] Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards 3.375 [85.72] Contact Tip Alignment Strip and .702 [17.83] Post Length .364 [9.24] .040 Min. [1.02] Contact Finish Area See E Below Related Product Data: Performance Specifications— page 98 Accessories—page 112 PC Board Edge Pattern—page 113 ACTION PIN Contact Mounting Hole Specifications—page 114 Application Tooling—page 115 Contact Replacement Tools— page 115 Special Application—page 96 .420 [10.67] .125 [3.18] 3.755 [95.38] .025 Sq. [0.64] Post .125 [3.18] .125 [3.18] Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-6727, 408-9186 .135 [3.43] Detail E Keying Plugs Intercontact (Plastic) Part No. 118982-1 On-Contact (Plastic) Part No. 119802-2 104 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Solder Type, Board-to-Board) AMP PACE Connector Specials, .125 x .125 [3.18 x 3.18] Centerline 27 Dual Positions Tin-Lead Posts .634 [16.10] Long Part No. 645394-1 18 or 36 Dual Positions Tin-Lead Posts .740 [18.80] Long Part No. 119552-2 Tin-Lead Posts .180 [4.57] Long Part No. 119880-1 97 Dual Positions (Two-piece Closed End/Open End with Partial Card Scoops and Card Guides) Contact Tyco Electronics for specific Part Number information. 105 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline Standard Housing .125 [3.18] .364 [9.24] .410 [10.41] B ±.006 [±0.15] C .005/.007 [0.13/0.18] .415 [10.54] Card Slot Depth See E Below Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths Accepts .054 to .071 [1.37 to 1.80] PC Boards .545 [13.84] .040 Min. [1.02] Contact Finish Area .702 [17.83] Post Length and Finish Area .025 Sq. [0.64] Post .093 Min. [2.36] .250 [6.35] A .125 [3.18] Housing with High Card Scoops .125 [3.18] .420 [10.67] B C ±.006 [±0.15] .005/.007 [0.13/0.18] .515 [13.08] Card Slot Depth See E Below .702 [17.83] Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths 3.375 [85.72] .364 [9.24] .040 Min. [1.02] Contact Finish Area .025 Sq. [0.64] Post .645 [16.38] .093 Min. [2.36] .250 [6.35] .125 [3.18] Typical Closed End/ Open End Housings Keying Plugs .125 [3.18] Intercontact (Plastic) Part No. 118982-1 Connectors can be mounted in pairs using any size combinations. .135 [3.43] Example: 1-30 pos. + 1-60 pos. = 1-90 pos. Detail E On-Contact (Plastic) Part No. 119802-2 106 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline (Continued) Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip—Clear polyester, type D Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Related Product Data: No. of Dual Positions A Dimensions B C 18 2.125 53.98 2.373 60.27 2.505 63.63 22 2.625 66.68 3.005 76.33 2.875 73.02 25 27 3.000 76.20 3.250 82.55 3.380 85.85 3.630 92.20 3.250 82.55 3.500 88.90 28 3.375 85.72 3.755 95.38 3.625 92.08 3.625 92.08 4.005 101.73 3.875 98.24 36 4.375 111.82 4.755 120.78 4.625 117.48 38 4.625 117.47 4.873 123.77 5.005 127.13 40 4.875 123.83 5.255 133.48 5.125 130.18 50 6.125 155.58 6.250 158.75 7.375 187.33 6.505 165.23 6.630 168.40 7.755 196.98 6.375 161.93 6.500 165.10 7.625 193.68 30 Performance Specifications— page 98 Accessories—page 112 PC Board Edge Pattern—page 113 ACTION PIN Contact Mounting Hole Specifications—page 114 Application Tooling—page 115 Contact Replacement Tools— page 115 Special Application—page 96 51 Technical Documents: (pages 186, 187): 60 Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2933, 408-2978, 408-2979, 408-9063, 408-9091, 408-9119, 408-9186 Post Length .180 4.57 .180 4.57 .500 12.70 .702 17.83 .180 4.57 .702 17.83 .180 4.57 .500 12.70 .180 4.57 .500 12.70 .180 4.57 .500 12.70 .180 4.57 .180 4.57 .702 17.83 .180 4.57 .500 12.70 .180 4.57 Closed End/Closed End Standard High Scoop Closed End/Open End High Scoop 1-119822-4 — 3-119840-2 1-119822-8 — — 1-119200-8 — — 1-119202-8 — — 1-119822-1 — — 1-119202-3 — — 1-119822-4 — — 1-119200-4 — — 1-119822-6 1-678034-1 — — 1-119841-6 — 2-119822-2 1-678034-2 — — 2-119841-2 — 2-119822-4 — 3-119840-9 2-119822-6 — — 2-119200-6 — — 3-119822-6 — — 3-119200-7 — — 4-119822-6 — — Note: Other connector sizes can be made available, consult Tyco Electronics. 107 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make Before Break Contacts Standard Housing .125 [3.18] .364 [9.24] .410 [10.41] B ±.006 [±0.15] C .005/.007 [0.13/0.18] .415 [10.54] Card Slot Depth See E Below Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths Accepts .054 to .071 [1.37 to 1.80] PC Boards .545 [13.84] .040 Min. [1.02] Contact Finish Area .702 [17.83] Post Length and Finish Area .025 Sq. [0.64] Post .093 Min. [2.36] .250 [6.35] A .125 [3.18] Housing with High Card Scoops .125 [3.18] .420 [10.67] B C ±.006 [±0.15] .005/.007 [0.13/0.18] .515 [13.08] Card Slot Depth See E Below .702 [17.83] Post Length and Finish Area Accepts .054 to .071 [1.37 to 1.80] PC Boards Contact Tip Alignment Strip on .500 [12.07] and .702 [17.83] Post Lengths 3.375 [85.72] .364 [9.24] .040 Min. [1.02] Contact Finish Area .025 Sq. [0.64] Post .645 [16.38] .093 Min. [2.36] .250 [6.35] .125 [3.18] Typical Closed End/ Open End Housings Keying Plugs .125 [3.18] Intercontact (Plastic) Part No. 118982-1 Connectors can be mounted in pairs using any size combinations. .135 [3.43] Example: 1-30 pos. + 1-60 pos. = 1-90 pos. Detail E On-Contact (Plastic) Part No. 119802-2 108 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make Before Break Contacts (Continued) Material and Finish: Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip—Clear polyester, type D No. of Dual Positions 18 24 A Dimensions B C Post Length Closed End/Closed End Standard Closed End/Open End High Scoop 2.125 53.98 2.875 76.20 2.505 63.63 3.123 79.25 2.373 60.27 3.058 77.67 .180 4.57 .180 4.57 1-1571235-1 — — 650059-2 Note: Other connector sizes can be made available, consult Tyco Electronics. Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Related Product Data: Performance Specifications— page 98 Accessories—page 112 PC Board Edge Pattern—page 113 ACTION PIN Contact Mounting Hole Specifications—page 114 Application Tooling—page 115 Contact Replacement Tools— page 115 Special Application—page 96 Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-2933, 408-2978, 408-2979, 408-9063, 408-9091, 408-9119, 408-9186 109 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline Material and Finish: Standard Housing Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated gold .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip—Clear polyester, type D .156 [3.96] B C ±.006 [±0.15] .005/.007 [0.13/0.18] Performance Specifications— page 98 Accessories—page 112 PC Board Edge Pattern—page 113 ACTION PIN Contact Mounting Hole Specifications—page 114 Application Tooling—page 115 Contact Replacement Tools— page 115 Special Application—page 96 .415 [10.54] Card Slot Depth See E Below .040 Min. [1.02] Contact Finish Area Post Length and Finish Area Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Related Product Data: .364 [9.24] .360 [9.14] Accepts .054 to .071 [1.37 to 1.80] PC Boards A .156 [3.96] Contact Tip Alignment Strip on .475 [12.07] and .702 [17.83] Post Lengths .025 Sq. [0.64] Post .545 [13.84] .093 Min. [2.36] .200 [5.08] Keying Plugs Technical Documents: (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-6726, 408-9186 Intercontact (Plastic) Part No. 118982-1 On-Contact (Plastic) Part No. 119802-2 .135 [3.43] Detail E No. of Dual Positions A Dimensions B C 15 2.184 55.47 2.626 66.70 2.495 63.39 18 2.652 67.36 3.094 78.59 2.964 75.29 22 3.276 83.21 3.718 94.44 3.588 91.13 28 43 4.212 106.98 6.552 166.42 4.654 118.21 6.994 177.65 4.524 114.91 6.864 174.35 Post Length Closed End/Closed End Standard .180 4.57 .475 12.07 .702 17.83 .475 12.07 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .475 12.07 .702 17.83 .180 4.57 .475 12.07 .702 17.83 1-119790-1 1-119254-1 1-119256-1 1-119254-4 1-119790-8 1-119254-8 1-119256-8 1-119790-4 1-119254-4 1-119256-4 2-119790-9 2-119254-9 2-119256-9 Note: Other connector sizes can be made available, consult Tyco Electronics. 110 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline w/Make Before Break Contacts Material and Finish: Card Scoop Housing Housing—Black glass-filled polyester, 94V-0 rated Contacts—Phosphor bronze, plated gold flash over .000030 [0.00076] min. thk. over .000050 [0.00127] min. thk. nickel in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Contact Tip Alignment Strip—Clear polyester, type D .156 [3.96] .364 [9.25] B .045 Contact Area [1.14] C .116 Contact Area [2.95] Note: Full palladium-nickel plated posts and other platings and plating thicknesses can be made available. Performance Specifications— page 98 Accessories—page 112 PC Board Edge Pattern—page 113 ACTION PIN Contact Mounting Hole Specifications—page 114 Application Tooling—page 115 Contact Replacement Tools— page 115 Special Application—page 96 Technical Documents: .200 [5.08] .005/.007 .093 Min. [0.13/0.18] [2.36] Accepts .054 to .071 [1.37 to 1.80] PC Boards Related Product Data: .228 [5.78] A .156 [3.96] Keying Plugs (pages 186, 187): Product Specifications 108-14019, 108-26003 Application Specification 114-26002 Instruction Sheets 408-6726, 408-9186 Intercontact (Plastic) Part No. 118982-1 On-Contact (Plastic) Part No. 119802-2 .135 [3.43] Detail E No. of Dual Positions A Dimensions B C Post Length Closed End/Closed End Scoop 18 2.652 67.36 3.094 78.59 2.964 75.29 .180 4.57 678035-1 Note: Other connector sizes can be made available, consult Tyco Electronics. 111 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Accessories for AMP PACE Connectors Connector Card Guide Material: Black glass-filled polyester Hole for #4 Self-Tapping Screw (mandatory) .050 [12.7] Deep Related Product Data: Mates with all standard housings (will not mate with some special housings) .370 [9.4] L Technical Documents: .410 [10.41] (pages 186, 187): .220 [5.59] Instruction Sheet 408-9091 .152 Dia. [3.96] (2 Holes) B Dimension from AMPPACEConnector Tables Plus .310 [7.87] L1 2.500 63.50 6.000 152.40 Part Numbers 1-117169-3 1-117169-3 1Other lengths up to 6.0 [152.4] can be made available. Consult Tyco Electronics for details. Ground Module Accepts .054 to.071 [1.37 to 1.80] PC Board Rating: 20 amperes per contact—Copper or aluminum bus .420 [10.67] Material and Finish: Housing—Black glass-reinforced thermoplastic Contact—CA 195, 3/4 hard, plated .000050 [0.00127] gold in contact area (front face only); .000100 [0.00254] tinlead on post, with entire contact underplated .000050 [0.00127] nickel .455 [11.56] .700 [17.78] Related Product Data: Mates with all standard housings (will not mate with some special housings) .060 [1.52] Contact Area .250 [6.35] .300 [7.62] Technical Documents: (pages 186, 187): Part No. 119341-1 Seating Tool 59881-1 Instruction Sheet 408-2978 112 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) PC Board Layout for AMP PACE Connectors Recommended PC Board Edge Pattern Gold Fingers .040 +.020 -.010 [1.016+.508 -.254 ] .430 [10.92] 30° .275 [6.99] .050 [1.27] Max. Chamfer B C .052±.002 [1.32±0.05] Key Slot ±.005 [±0.13] .054-.071 [1.37-1.80] A1 1A Max. = Minimum connector card slot -.001 [-0.03]. A Min. = Minimum connector card slot -.011 [-0.28]. Note: Finger pattern to be centered on daughter card. Each finger can deviate .003 [0.08] from true position. AMP PACE Connector Centerline Spacing .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 .125 x .125 3.18 x 3.18 .125 x .250 3.18 x 6.35 .156 x .200 3.96 x 5.08 Dimensions B .100 2.54 .100 2.54 .125 3.18 .125 3.18 .156 3.96 C .070 1.78 .070 1.78 .080 2.03 .080 2.03 .080 2.03 113 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) AMP PACE Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide break-through and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today’s standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. ➀ Annular Ring (See Note) ➁ Drilled Hole ➂ Copper Thickness ➃ Tin-Lead Thickness ➄ Plated Through-Hole Mounting Hole Specifications Connector No. of Dual Centerline Positions .125 x .125 28, 97 3.18 x 3.18 .156 x .200 15-43 3.96 x 5.08 .125 x .125 3.18 x 3.18 27 .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 .125 x .125 3.18 x 3.18 .125 x .250 3.18 x 6.35 15-60 15-60 18, 36 ACTION PIN Contact Material Thickness Drilled Hole Diameter➁ .025 0.64 .0453±.001 1.151±0.03 .001-.003 0.03-0.08 .0003 0.008 Min. .037-.043 0.94-1.09 Not Specified Not Specified .025 0.64 .0465±.001 1.181±0.03 .001-.003 0.03-0.08 .0003 0.008 Min. .037-.043 0.94-1.09 Not Specified Not Specified .025 0.64 .0453±.001 1.151±0.03 .001-.003 0.03-0.08 .0003 0.008 Min. .037-.043 0.94-1.09 .0015 0.038 .002 0.05 Plating Thicknesses Copper➂* Tin-Lead➃ Plated Through-Hole Diameter➄ Radial Hole Distortion Average Maximum 18-60 *Maximum hardness of copper layer is 150 Knoop. Note: Recommended annular ring diameter is hole diameter plus .020 [0.51]. 114 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Application Tooling for AMP PACE Connectors Modular Seating Tools Available from Tyco Electronics is a complete series of AMP PACE Modular Seating Tools for installing AMP PACE Connectors on printed circuit boards and panels. These tools are modular in design in that housing tool holders may be added or subtracted to accommodate several different connector sizes. In addition, all tool parts are individually replaceable should the tool become damaged. Modular seating tools are supplied in two basic designs: One which covers all connector centerlines except .100 x .100 [2.54 x 2.54] and one for the .100 x .100 [2.54 x 2.54] centerline connectors. All seating tools have a common shut height of 1.5 inches [38]. This allows AMP PACE and other ACTION PIN products to be seated at the same time on AMP seating machines. See page 149 for a description of the AMP seating machines. .100 x .100 [2.54 x 2.54] Centerline Spacing .100 x .200 [2.54 x 5.08], .125 x .125 [3.18 x 3.18], .125 x .250 [3.18 x 6.35], For Connectors without Scoops No. of Dual Positions 15 18 20 22 25 28 30 31 32 34 35 36 37 40 43 44 48 50 51 54 55 56 60 .156 x .200 [3.96 x 5.08] Centerline Spacing Centerline .100 x .100 [2.54 x 2.54] 1-58200-1 — 1-58200-6 — 1-58200-1 1-58200-4 1-58200-6 1-58200-7 — — 2-58200-1 — — 2-58200-6 — — 3-58200-4 3-58200-6 3-58200-7 4-58200-0 4-58200-1 — 4-58200-6 .100 x .200 [2.54 x 5.08] 1-58140-1 1-58140-4 1-58140-6 1-58140-8 1-58140-1 1-58140-4 1-58140-6 — 1-58140-8 2-58140-0 2-58140-1 2-58140-2 2-58140-3 2-58140-6 2-58140-9 3-58140-0 — 3-58140-6 — — 4-58140-1 — 4-58140-6 .125 x .250 [3.18 x 6.35] — 1-58142-4 — 1-58142-8 1-58142-1 1-58142-4 1-58142-6 — — — — 2-58142-2 — 2-58142-6 — — — 3-58142-6 3-58142-7 — — 4-58142-2 4-58142-6 .156 x .200 [3.96 x 5.08] 1-58143-1 — — 1-58143-8 — 1-58143-4 — — — — — — — — 2-58143-9 — — — — — — — — For Connectors with Scoops No. of Dual Positions 15 18 22 28 30 38 50 55 Contact Replacement Tools Centerline Replacement tools listed in the chart at the right are used to install replacement contacts in AMP PACE connector housings. Replacement Tool 1-265871-7 is used to remove all .025 [0.64] square posts from PC boards. .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 .125 x .125 3.18 x 3.18 .125 x .250 3.18 x 6.35 .156 x .200 3.96 x 5.08 .100 x .200 [2.54 x 5.08] 1-58150-1 — 1-58150-8 — 1-58150-6 — 3-58150-6 4-58150-1 Standard Centerline .125 x .125 [3.18 x 3.18] — — — 1-58218-4 — — — — .125 x .250 [3.18 x 6.35] — 1-58184-4 — — — 2-58184-4 3-58184-6 — Housing Style Full Card Scoop 266220-3 — 266220-1 58210-1 — 58210-4 266220-2 58210-2 266220-2 — Note: Tooling availability is dependent upon part number activity. Consult Tyco Electronics for further information. 115 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) TELEDENSITY Connectors Product Facts High density - .0625 [1.586] contact centerlines ■ Compliant ACTION PIN contacts press-fit into plated-through holes for solderless application ■ Individually replaceable contacts ■ Accommodates up to three levels of daughter card pads for sequencing ■ .125 [3.18] square grid post arrangement ■ Performance Specifications Current Rating*: 3 amperes max. Mating Force (Contact Pair): 1 lb. [4.4 N] max. Durability (Mating Cycles): 100 min. Termination Resistance: 12 milliohms max. Dielectric Rating: 1200 VAC (rms) Insulation Resistance: 5000 megohms max. The high performance AMP TELEDENSITY connector is a high density, card edge, telecommunications connector. It features compliant ACTION PIN contacts for solderless application to multi-layer printed circuit boards with plated-through or bare copper holes. These connectors accept .054 to .072 [1.37 to 1.83] thick daughter cards. To satisfy the broadest range of application needs, the Operating Temperature: –55°C to +85°C contacts are plated with 30 microinches of gold in the mating area and tin-lead on the posts. A plastic locating strip keeps posts positioned correctly for board insertion. For high-density needs, TELEDENSITY connectors offer a .0625 [1.586] daughter card contact centerline spacing in 39-, 71-, or 99dual positions. The connector’s .330 [8.38] slot depth accommodates up to three levels of daughter card pads for sequencing, while a biasing wedge maintains proper pad alignment during card extraction. Posts are arranged in a .125 [3.18] square grid to ease circuit routing. *Consult Tyco Electronics when paralleling contacts for power applications. 116 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) TELEDENSITY Connectors, .0625 [1.586] Centerline Material and Finish: Housing—Black polyester Contacts—Copper alloy 725, plated .000030 [0.00076] gold in contact area, .000030 [0.00076] solder plate on post, with entire contact underplated .000100 [0.00254] nickel Coil Spring—Stainless steel Contact Tip Alignment Strip—Clear polyester Related Product Data: Performance Specifications— page 116 ACTION PIN Contact Mounting Hole Specifications—page 118 Technical Document—pages 186, 187 Product Specification— 108-26003 Instruction Sheet— 408 6866 Number of Dual Positions 39 71 99 Dimensions A B 3.168 80.47 2.588-2.600 65.74-66.04 5.168 131.27 6.918 175.72 4.588-4.600 116.54-116.84 6.338-6.350 160.99-161.29 C .634 16.10 .350 8.89 .634 16.10 .634 16.10 D Connector Part Numbers 2.375 60.33 4.375 111.13 6.125 155.58 Seating Tool Numbers** 650148-1 58084-1 650281-1* 650149-1 58084-3 650150-1 58084-2 * Contacts in this connector are underplated .000150 [0.00381] nickel. ** See page 149 for a description of AMP seating machines. Recommended PC Board Layout (Shown from post side) For mounting hole specifications, see page 123 Note: ACTION PIN posts require .093 [2.36] min. thick PC board. 117 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) TELEDENSITY Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide breakthrough and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today’s standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. ➀ Annular Ring (See Note) ➁ Drilled Hole ➂ Copper Thickness ➃ Tin-Lead Thickness ➄ Plated Through-Hole Mounting Hole Specifications ACTION PIN Contact Material Thickness Drilled Hole Diameter➁ Copper➂* .025 0.64 .0453±.001 1.151±0.03 .001-.003 0.03-0.08 Plating Thicknesses Tin-Lead➃ Plated-Through Hole Diameter➄ Average Maximum .037-.043 0.94-1.09 .0015 0.038 .002 0.05 .0003 Min. 0.008 Radial Hole Distortion *Maximum hardness of copper layer is 150 Knoop Note: Recommended annular ring diameter is hole diameter plus .020 [0.51] 118 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors Performance Specifications Electrical Characteristics Contact Resistance: 8 milliohms (max.) Insulation Resistance: 2,000 megohms (min.) Continuous Current Rating*: 3 amperes Physical Characteristics Card Insertion Force: 16 oz [4.45 N] (max.) per contact pair Card Extraction Force: 1 oz [0.28 N] (min.) per contact pair Retention (in PC Board): 7 lb [31.1 N] (min.) Operating Temperature: –65°C to +125°C AMP ECONOMATE Connectors provide a reliable and economical method for interconnecting backplane panels, using either two-sided or multilayer PC boards. Connector housings are furnished unloaded and are available for post centerline spacings of: .100 x .200 [2.54 x 5.08] and .156 x .200 [3.96 x 5.08]. The housings are simply positioned onto the contacts, after the contacts have been inserted into the PC board and the carrier strip removed. Contacts from Tyco Electronics feature the proven and reliable ACTION PIN contact design.These press-fit contacts employ two spring members that compress to exert force against the plated through-holes for a gas-tight connection. Gold plating of contacts promotes the electrical integrity of the connection. Important: Application tooling is absolutely necessary for installing contacts and housings onto PC boards. See page 126 for application tooling. Feed-through posts are also available for accepting wrap-type terminations. These posts also feature the ACTION PIN contact design and are supplied in strip form and stored on reels for insertion into PC boards. *Consult Tyco Electronicsengineering when paralleling contacts for power applications. 119 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) .100 x .200 [2.54 x 5.08] Centerline Spacing B (Card Slot Length) A Material and Finish: Housing—Black glass-filled nylon Contacts—Copper alloy 725, plated as follows: Plating A—Selectively plated .000030 [0.00076] min. gold in contact area, .000001 [0.00003] min. gold on remainder of contact, with entire contact underplated .000050 [0.00127] min. nickel Plating B—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel Plating C—Selectively plated .000100 [0.00254] min. gold in contact area, .000001 [0.00003] min. gold on remainder of contact, except .000050 [0.00127] min. gold for .200 [5.08] from tip of post, with entire contact underplated .000050 [0.00127] min. nickel No. of Dual Positions .100 [2.54] 2.734 82.14 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 5.234 132.94 6.234 158.34 25 30 Accepts .054-.071 [1.37-1.80] PC Boards 35 36 40 50 60 2.604 78.84 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 5.104 129.64 6.104 155.04 1-117798-4 1-117798-3 1-117798-6 1-117798-7 1-117798-8 1-117798-1 1-117798-2 Note: Other connector sizes can be made available, consult Tyco Electronics. .415 [10.54] .181 [4.60] Related Product Data: Performance Specifications— page 119 Card Guides—page 122 ACTION PIN Contact Mounting Hole Specifications—page 125 Application Tooling—page 126 Housing Part Numbers Dimensions A B Contact Area .545 [13.84] L .093-.125 [2.36-3.18] .200 [5.08] .025 Sq. [0.64] Technical Documents: (pages 186, 187): Product Specification 108-26002 .100 [2.54] Dimension L Keying Plugs .475 12.07 .702 17.83 Make-Before-Break Contacts Plating A Contact Part Numbers* Plating B Plating C 2-117795-4 4-117795-0 — 1-117795-3 2-117795-6 4-117795-8 *Contacts are strip form, 35,000 per reel. Intercontact (Plastic) Part No. 118982-1 Dimension L .040 Ref. [1.02] Gold in Contact Area On-Contact (Plastic) Part No. 119802-2 .475 12.07 .702 17.83 Make Before Break Contact Part Numbers* Plating A Plating B — 4-118951-8 1-118951-4 — .025 Sq. [0.64] .100 [2.54] 120 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) 3.588 [91.14] (Card Slot Length) .156 x .200 [3.96 x 5.08] Centerline Spacing 3.718 [94.44] Material and Finish: Housing—Black glass-filled nylon Contacts—Copper alloy 725, plated as follows: Plating A—Selectively plated .000030 [0.00076] min. gold in contact area, .000001 [0.00003] min. gold on remainder of contact, with entire contact underplated .000050 [0.00127] min. nickel Plating B—Duplex plated .000030 [0.00076] min. gold in contact area, .000100 [0.00254] min. tin-lead on posts, with entire contact underplated .000050 [0.00127] min. nickel .156 [3.96] Accepts .054-.071 [1.37-1.80] PC Boards .702 [17.83] .150 Ref. [3.01] Gold in Contact Area .025 Sq. [0.64] 22 Dual Position Housing Part No. 117296-4 .150 [3.06] Related Product Data: Make-Before-Break Contacts Performance Specifications— page 119 Card Guides—page 122 ACTION PIN Contact Mounting Hole Specifications—page 125 Application Tooling—page 126 Technical Documents: (pages 186, 187): Product Specification 108-26002 .181 [4.60] .415 [10.54] .545 [13.84] Keying Plug Contact Area .093-.125 [2.36-3.18] L .200 [5.08] .025 Sq. [0.64] Note: Other connector sizes can be made available, consult Tyco Electronics. Intercontact (Plastic) Part No. 118982-1 .156 [3.96] Make Before Break Contacts Dimension Part Plating L Numbers* .475 B 1-118778-2 12.07 .702 A 118778-6 17.83 Dimension L .475 12.07 .702 17.83 Contact Part Numbers* 117285-7 117285-8 *Contacts are strip form, 15,000 per reel. 121 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Card Guides for ECONOMATE Connectors Material: Black glass-filled nylon Related Product Data: Mates with all .100 x .200 [2.54 x 5.08] and .156 x .200 [3.96 x 5.08] centerline housings Technical Documents: (pages 186, 187): Instruction Sheet 408-9091 Hole for No. 4 Screw 0.45 deep [11.43] L .220 [5.59] .410 [10.41] .152 Dia. [3.86] (2 Plcs.) A1 Recommended Mounting Dimensions Dimension L* 2.500 63.50 6.000 152.40 Card Guide Part Numbers 1-117169-3 1-117169-3 *Other lengths can be made available in .500 [12.70] increments from 1.500 [38.10] to 6.500 [165.10]. Consult Tyco Electronics for details. Housing Centerline No. of Dual Spacing Positions 30 35 .100 x .200 2.54 x 5.08 36 40 50 60 .156 x .200 3.96 x 5.08 22 Dimension A1 3.544 90.02 4.044 102.72 4.144 105.26 4.544 115.42 5.544 140.82 6.544 166.22 4.028 102.31 Note: A1 dimension = A dimension of ECONOMATE housing plus .310 [7.87]. 122 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Center Carrier Feed-Thru Posts* .100 [2.54] Centerline, Wrap Type Dimensions Material: Copper Alloy 725 Finish – Gold plate per MIL-G-45204 over nickel plate per QQ-N-290 (see table for thicknesses) Recommended Hole Size: Non-Plated-thru Hole - .0453±.001 [1.15±0.03], 1.15 mm drill .004 0.1 Plated-thru Hole - .039 ± .003 [0.99 ± 0.08], 1.15 mm drill Part Numbers 1) .000001 [0.00003] min. gold flash over .000050 [0.0013] min. nickel plate 2) .000050 [0.0013] min. gold plate over .000050 [0.0013] min. nickel plate A B C .318 8.08 .578 14.68 .578 14.68 .380 9.65 .687 17.45 .460 11.68 .550 13.97 .823 20.90 1.005 25.53 1.038 26.37 1.128 28.65 1.203 30.56 — 118243-8 1-118243-1 — .100 [2.54] Centerline, TERMI-POINT Clip Part Number 119136-2 Material: Copper Alloy 725 Finish – 1) Gold plate per MIL-G-45204, .000030 [0.00076] min. thk. over nickel plate per QQ-N-290, .000050 [0.0013] min. thk. 2) Gold flash per MIL-G-45204, .000001 [0.00003] min. thk. over nickel plate per QQ-N-290, .000050 [0.0013] min. thk. Recommended Hole Size: Non Plated-thru Hole - .0453±.001 [1.15±0.03], 1.15 mm drill .004 0.1 Plated-thru Hole - .039±.003 [0.99± 0.08], 1.15 mm drill .125 [3.18] Centerline, Wrap Type Material: Copper Alloy 725 Finish – Gold plate per MIL-G-45204 or solder plate over nickel plate per QQ-N-290 (see table for thicknesses) Recommended Hole Size: - .0453±.001 Non Plated-thru Hole [1.15±0.03], 1.15 mm drill .004 0.1 Plated-Thru Hole - .039 ± .003 [0.99± 0.08], 1.15 mm drill Dimensions A B .703 17.68 .548 13.92 Part Numbers .000100 [0.0025] min. .000030 [0.00076] tin plate over gold plate over .000050 [0.0013] min. .000050 [0.0013] nickel plate nickel plate 117311-7 1-117311-0 *Use AMP Cut and Transfer Machine for center carrier post insertion. Consult Tyco Electronics. 123 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) Feed-Through Posts .100 [2.54] Centerline Spacing Material and Finish: Copper alloy 725, plated as follows: Plating A—Selectively plated .000030 [0.00076] min. gold in Area (1), .000001 [0.00003] min. gold in Area (2), with entire post underplated .000050 [0.00127] min. nickel Plating B—.000030 [0.00076] min. gold over .000100 [0.00254] min. nickel on entire post Plating C—.000050 [0.00127] min. gold over .000100 [0.00254] min. nickel on entire post Plating D—.000100 [0.00254] min. tin-lead over .000050 [0.00127] min. nickel on entire post .318 [8.08] (1) .045 [1.14] .030 [0.76] (2) A Pre-Notch .025 [0.64] .100 [2.54] Dimension A .687 17.45 .500 12.70 Plating A 1-117249-7 13-117249-11 3-117249-2 .025 [0.64] Feed-Through Post Part Numbers* Plating B Plating C Plating D 1-117249-2 1-117249-2 6-117249-5 — — 5-117249-6 *Posts in strip form, 50,000 per reel. 1Pre-notched to break with 120° bend. .150 [3.81] Centerline Spacing Material and Finish: Copper alloy 725, selectively plated .000030 [0.00076] min. gold in Area (1), .000001 [0.00003] min. gold in Area (2), with entire post underplated .000050 [0.00127] min. nickel .318 [8.08] (1) .045 [1.14] .030 [0.76] (2) .687 [17.45] .150 [3.81] .025 [0.64] .025 [0.64] 50,000 per reel Part No. 117269-5 124 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) ECONOMATE Connectors (Continued) AMP ACTION PIN Press-Fit Contacts ACTION PIN contacts provide a reliable press-fit connection. Localized pressure in the interface area entails oxide break-through and helps prevent corrosion in the harshest environments to provide a reliable connection virtually every time. Also, radial and axial distortion are controlled to meet today’s standards for multilayer board applications. PC Board Thickness ACTION PIN contacts are designed for use in a variety of PC board thicknesses. However, certain ACTION PIN contacts are to be used in specific ranges of board thicknesses. To promote optimum performance, the recommended board thicknesses provided with the connector being used must be followed. ➀ Annular Ring (See Note) ➁ Drilled Hole ➂ Copper Thickness ➃ Tin-Lead Thickness ➄ Plated Through-Hole Mounting Hole Specifications Connector No. of Dual Centerline Positions .100 x .200 30, 35, 36, 2.54 x 5.08 40, 50, 60 .156 x .200 22 3.96 x 5.08 ACTION PIN Contact Material Thickness Drilled Hole Diameter➁ .025 0.64 .0453±.001 1.151±0.03 Plating Thicknesses Copper➂* Tin-Lead➃ .001-.003 0.03-0.08 .0003 0.008 Min. Plated Through-Hole Diameter➄ .037-.043 0.94-1.09 Radial Hole Distortion Average Maximum Not Specified Not Specified *Maximum hardness of copper layer is 150 Knoop. Note: Recommended annular ring diameter is hole diameter plus .020 [0.51]. 125 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Application Tooling for ECONOMATE Connectors Available from Tyco Electronics is a complete series of ACTION PIN Assembly Tooling Kits for ECONOMATE connector housings and feed-through posts. Assembly Kit tools provide the means for installing housings and contacts onto printed circuit boards, as well as removing housings and contacts from the printed circuit boards. All tools are available in kits, or may be purchased individually. In many instances, part number series are listed in the charts. Specific dash numbers and detailed information on the contacts and housings are presented on the respective product specification pages. For specific dash numbers and complete information on the tooling, contact Tyco Electronics. For ECONOMATE Connectors ACTION PIN Contacts Pin Length Part Numbers .125 x .125 3.18 x 3.18 .702 17.83 117793-■ 15-60 117796-■ .100 x .200 2.54 x 5.08 .702 17.83 117795-■ 15-60 117798-■ .156 x .200 3.96 x 5.08 .702 17.83 117285-■ 15-50 117296-■ .156 x .200 3.96 x 5.08 .475 12.07 117285-■ 15-50 117296-■ .100 x .200 2.54 x 5.08 .475 12.07 117795-■ 15-60 117798-■ .100 2.54 .340 8.64 117880-■ 20-60 117879-■ Centerline ECONOMATE Housings No. of Dual Part Positions Numbers ACTION PIN Assembly Tool Numbers Applicator 265902-■ Carrier Removal Tool 265924-■ Housing Assembly Tool 58292-■ Housing Removal Tool 265868-1 Pin Replacement Tool 265871-2 Applicator 265904-■ Carrier Removal Tool 265924-■ Housing Assembly Tool 265879-■ Housing Removal Tool 265868-1 Pin Replacement Tool 265871-2 Applicator 265905-■ Carrier Removal Tool 265924-■ Housing Assembly Tool 265881-■ Housing Removal Tool 265868-1 Pin Replacement Tool 265871-2 Applicator 265906-■ Carrier Removal Tool 265924-■ Housing Assembly Tool 265881-■ Housing Removal Tool 265868-1 Pin Replacement Tool 265871-3 Applicator 266129-■ Carrier Removal Tool 265924-■ Housing Assembly Tool 265879-■ Housing Removal Tool 265868-1 Pin Replacement Tool 265871-3 Applicator 265937-■ Carrier Removal Tool 265924-■ Housing Assembly Tool 265962-■ Housing Removal Tool 265868-2 Pin Replacement Tool 1-265871-1 For Feed-Through Posts ACTION PIN Contacts Pin No. of Length Positions Centerline Part Numbers .100 2.54 .500-.687 12.70-17.45 8-60 117249-■ .125 3.18 .687 17.45 8-60 117272-■ .150 3.81 .687 17.45 8-50 117269-■ .150 3.81 .365-.475 9.27-12.07 8-50 117269-■ Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. ACTION PIN Assembly Tool Numbers Applicator 265910-■ Carrier Removal Tool 265924-■ Pin Replacement Tool 265871-7 Applicator 265911-■ Carrier Removal Tool 265924-■ Pin Replacement Tool 265871-7 Applicator 265912-■ Carrier Removal Tool 265924-■ Pin Replacement Tool 265871-7 Applicator 265931-■ Carrier Removal Tool 265924-■ Pin Replacement Tool 265871-7 126 Catalog 1654080 Issued 7-03 www.tycoelectronics.com USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) High Density Press-Fit Card Edge Product Facts High density .050" [1.27] center spacing. ■ Staggered contacts for low insertion force. ■ Designed for multi-layer .093" [2.36] daughter cards. ■ High temperature SMT solder reflow temperatures of 260° for 30 seconds. ■ Unique pin geometry allows for even distribution of forces reducing axial pin rotation and preserving perpendicularity to the PCB board. ■ Edge and side coining provides a uniform pin radius ensuring maximum contact without "skiving" the plated hole. ■ Full complement of application tooling available. ■ Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ ■ Certified by Canadian Standards Association, File No. LR 49571 ® High Density (.050" [1.27] center spacing) Press-Fit connectors from Tyco Electronics are designed for high density backplane or mid-plane applications. Compliant pin connectors from Tyco Electronics meet or exceed requirements of current industry standards, including Bellcore specifications, which address critical performance issues such as hole retention, hole deformation and environmental performance. Electrical Characteristics: Operating Voltage–600VDC (sea level) Current Rating –1.5 Amperes Initial Contact Resistance – 30 milliohms Environmental Characteristics: Operating Temperature – -55˚C to +125˚C Temperature Cycling – MIL-STD-202 method 107 Vibration– MIL-STD-202, method 204 127 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) .050 [1.27] Centerline For .093 [2.36] Thick Daughter Cards Material and Finish: Insulation Resistance—1000 megohms minimum Contact Retention into PCB—2 lbs. min. Insertion Force—10 oz. max. Mating Force—2 oz. per contact Housing—High Temp. Glass filled thermoplastic, UL rating 94V-0 Color—Black Spring Contact—BeCu Contact Plating—Palladium Nickel +.005 .066 -.010 +.127 [1.68 -.254 ] X .610 [15.49] .461 .421 [11.71] [10.69] .016 [.41] .148 [3.76] .138 [3.51] X Section X-X “A” Spaces • .050 [1.27] = B D C (Card Slot) .132 [3.35] .400 [10.15] .332 [8.43] E Note: Dimension E is Connector Mounting PC Hole Pattern. 128 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Ordering Information No. of Dual Readout Position A 20 19 30 29 40 39 50 49 60 59 Dimensions B C D E F 0.950 [24.13] 1.450 [36.83] 1.950 [49.53] 2.450 [62.23] 2.950 [74.93] 1.040 [26.42] 1.540 [39.12] 2.040 [51.82] 2.540 [64.52] 3.040 [77.22] 1.230 [31.24] 1.730 [43.94] 2.230 [56.64] 2.730 [69.34] 3.230 [82.04] 1.100 [27.94] 1.600 [40.64] 2.100 [53.34] 2.600 [66.04] 3.100 [78.74] 1.010 [25.65] 1.510 [38.35] 2.010 [51.05] 2.510 [63.75] 3.010 [76.45] TYCO Part Number Acquired Part Number 147668-2 C9D020PF60048 147668-3 C9D030PF60048 147668-4 C9D040PF60048 147668-5 C9D050PF60048 147668-6 C9D060PF60048 E ø .024±.002 (.61±.05) ø .096 (2.44) .166 [4.22] .066 [1.68] .096 [2.44] .075 [1.90] “A” Spaces at .050 [1.27] = B Connector Mounting PC Hole Pattern F R .047 Typ. [1.19] .093 Thick PC Board [2.36] “A” Spaces • .050 [1.27] = B .030 [.76] Y .320 Min. [8.13] .585 [14.86] .150 [3.81] Y 45° x .025 [.64] All Around .035 [.89] Typ. .125 [3.17] Section Y-Y Daughter Board Configuration 129 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) .100 x .100 [2.54 x 2.54] Centerline Press Fit, with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [3.37 to 1.80] .120±.003 [3.05±.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance— 5000 megohms minimum Contact Retention Into PCB— 5lbs. min. [356 N] Insertion Force—10 oz. [44.5 N] max. measured with a .0700 ± .0001 [1.80±.00254] THK polished blade per MIL-C-21097C Withdrawal Force—1 oz. min. [4.54 N] measured with a .0540 ± .0001 [3.37±.000254] THK polished test blade per MIL-C-21097C after sizing 3 times with a .0700 ± .0001 [1.80±.00254] THK blade Insulator Body—High Temp. Glass filled thermoplastic, UL rating 94V-O Color—Black Spring Contact—Phosphor Bronze alloy Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .100 [2.54] A B C .020 [.51] Contact Gap .365 [9.27] Ref. .100 [2.54] Electrical Properties: .550 [13.97] Operating Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms J Environmental Properties: .100 [2.54] Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration—MIL-STD-202, method 204 .025 Sq. Typ. [.64] C .040±.003 [1.02±.08] Dia. Dim C Application Tooling: Insertion Tool—page 150 Related Product Data: Daughter Card Edge Pattern— page 57 .100 [2.54] .100 [2.54] 130 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Press-Fit Board-To-Board) Ordering Information .100 [2.54] Centerline/.100 [2.54] Row-To-Row with Standoffs Dimensions No. of Dual Readout Positions Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth A B C .300 [7.62] Card Slot Depth 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 C1D18PF29013 C1D18PF29133 C1D18PF29043 C1D20PF29013 C1D20PF29133 C1D20PF29043 C1D22PF29013 C1D22PF29133 C1D22PF29043 C1D25PF29013 C1D25PF29133 C1D25PF29043 C1D28PF29013 C1D28PF29133 C1D28PF29043 C1D30PF29013 C1D30PF29133 C1D30PF29043 C1D35PF29013 C1D35PF29133 C1D35PF29043 C1D36PF29013 C1D36PF29133 C1D36PF29043 C1D40PF29013 C1D40PF29133 C1D40PF29043 C1D43PF29013 C1D43PF29133 C1D43PF29043 C1D45PF29013 C1D45PF29133 C1D45PF29043 C1D50PF29013 C1D50PF29133 C1D50PF29043 C1D60PF29013 C1D60PF29133 C1D60PF29043 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 C1D18PF29015 C1D18PF29135 C1D18PF29045 C1D20PF29015 C1D20PF29135 C1D20PF29045 C1D22PF29015 C1D22PF29135 C1D22PF29045 C1D25PF29015 C1D25PF29135 C1D25PF29045 C1D28PF29015 C1D28PF29135 C1D28PF29045 C1D30PF29015 C1D30PF29135 C1D30PF29045 C1D35PF29015 C1D35PF29135 C1D35PF29045 C1D36PF29015 C1D36PF29135 C1D36PF29045 C1D40PF29015 C1D40PF29135 C1D40PF29045 C1D43PF29015 C1D43PF29135 C1D43PF29045 C1D45PF29015 C1D45PF29135 C1D45PF29045 C1D50PF29015 C1D50PF29135 C1D50PF29045 C1D60PF29015 C1D60PF29135 C1D60PF29045 Tail Length .180 [4.57] (Dim. “J”) 18 20 22 25 28 30 35 36 40 43 45 50 60 Tail Length .475 [12.07] (Dim. “J”) 18 20 22 25 28 30 35 36 40 43 45 50 60 131 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100" [2.54] Centerline / .100" [2.54] Row-to-Row with Standoffs Dimensions No. of Dual Readout Positions A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Numbers .300 [7.62] Card Slot Depth .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth Tail Length .625 [15.88] (Dim. “J”) 18 20 22 25 28 30 35 36 40 43 45 50 60 C1D18PF29017 C1D18PF29137 C1D18PF29047 C1D20PF29017 C1D20PF29137 C1D20PF29047 C1D22PF29017 C1D22PF29137 C1D22PF29047 C1D25PF29017 C1D25PF29137 C1D25PF29047 C1D28PF29017 C1D28PF29137 C1D28PF29047 C1D30PF29017 C1D30PF29137 C1D30PF29047 C1D35PF29017 C1D35PF29137 C1D35PF29047 C1D36PF29017 C1D36PF29137 C1D36PF29047 C1D40PF29017 C1D40PF29137 C1D40PF29047 C1D43PF29017 C1D43PF29137 C1D43PF29047 C1D45PF29017 C1D45PF29137 C1D45PF29047 C1D50PF29017 C1D50PF29137 C1D50PF29047 C1D60PF29017 C1D60PF29137 C1D60PF29047 132 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline Press-Fit, Full Scoop Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .21 Point of Contact [5.33] .395/.510 Card Slot Depth [10.03/12.95] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB— 5lbs. min. [356 N] Insertion Force—10 oz. [44.5 N] max. measured with a .0700 ± .0001 [1.80±.00254] THK polished blade per MIL-C-21097C Withdrawal Force—1 oz. min. [4.5 N] measured with a .0540 ± .0001 [3.37±.00254] THK polished test blade per MIL-C-21097C after sizing 3 times with a .0700 ± .0001 [1.80±.00254] THK blade Insulator Body—High Temp. Glass filled thermoplastic, UL rating 94V-O Color—Black Spring Contact—Phosphor Bronze alloy Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] B C .020±.010 [.51±.25] Contact Gap .390 [9.91] .100 [2.54] B .395/.510 Card Slot Depth [10.03/12.95] .645 Ref. [16.38] Electrical Properties Operating Voltage—600 VDC (sea level) Current Rating—3 Amperes Contact Resistance—10 milliohms J A Environmental Properties: C Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 Dim E .040±.003 [1.02±.08] Dia. Application Tooling: Insertion Tool—page 150 .200 [5.08] Related Product Data: Daughter Card Edge Pattern— page 57 .100 [2.54] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 133 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop Dimensions No. of Dual Readout Positions A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Numbers .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth Tail Length .670 [17.02] (DIM “J”) 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18PF29012 W8D18PF29042 W8D20PF29012 W8D20PF29042 W8D22PF29012 W8D22PF29042 W8D25PF29012 W8D25PF29042 W8D28PF29012 W8D28PF29042 W8D30PF29012 W8D30PF29042 W8D35PF29012 W8D35PF29042 W8D36PF29012 W8D36PF29042 W8D40PF29012 W8D40PF29042 W8D43PF29012 W8D43PF29042 W8D45PF29012 W8D45PF29042 W8D50PF29012 W8D50PF29042 W8D60PF29012 W8D60PF29042 W8D18PF29013 W8D18PF29043 W8D20PF29013 W8D20PF29043 W8D22PF29013 W8D22PF29043 W8D25PF29013 W8D25PF29043 W8D28PF29013 W8D28PF29043 W8D30PF29013 W8D30PF29043 W8D35PF29013 W8D35PF29043 W8D36PF29013 W8D36PF29043 W8D40PF29013 W8D40PF29043 W8D43PF29013 W8D43PF29043 W8D45PF29013 W8D45PF29043 W8D50PF29013 W8D50PF29043 W8D60PF29013 W8D60PF29043 Tail Length .180 [4.57] (DIM “J”) 18 20 22 25 28 30 35 36 40 43 45 50 60 134 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline, Press-Fit, Full Scoop with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ .21 Point of Contact [5.33] .395/.510 Card Slot Depth [10.03/12.95] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB— 5lbs. min. [356 N] Insertion Force—10 oz. [44.5 N] max. measured with a .0700 ± .0001 [1.80±.00254] THK polished blade per MIL-C-21097C Withdrawal Force—1 oz. min. [4.5 N] measured with a .0540 ± .0001 [3.37±.00254] THK polished test blade per MIL-C-21097C after sizing 3 times with a .0700 ± .0001 [1.80±.00254] THK blade Insulator Body—High Temp. Glass filled thermoplastic, UL rating 94V-O Color—Black Spring Contact—Phosphor Bronze alloy Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] B C .020±.010 [.51±.25 ] Contact Gap .390 [9.91] .100 [2.54] B .395/.510 Card Slot Depth [10.03/12.95] .705 Ref. [17.91] Electrical Properties: Operating Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms J C A Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 Dim C .040±.003 [1.02±.08] Dia. Application Tooling: Insertion Tool—page 150 Related Product Data: .200 [5.08] Daughter Card Edge Pattern— page 57 .100 [2.54] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 135 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop with Standoffs Dimensions No. of Dual Readout Positions A B C 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 2.034 51.66 2.234 56.74 2.434 61.82 2.734 69.44 3.034 77.06 3.234 82.14 3.734 94.84 3.834 97.38 4.234 107.54 4.534 115.16 4.734 120.24 5.234 132.94 6.234 158.34 1.904 48.36 2.104 53.44 2.304 58.52 2.604 66.14 2.904 73.76 3.104 78.84 3.604 91.54 3.704 94.08 4.104 104.24 4.404 111.86 4.604 116.94 5.104 129.64 6.104 155.04 1.700 43.18 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.400 111.76 4.900 124.46 5.900 149.86 Acquired Part Numbers .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth Tail Length .670 [17.02] (DIM “J”) 18 20 22 25 28 30 35 36 40 43 45 50 60 W8D18PF29062 W8D18PF29092 W8D20PF29062 W8D20PF29092 W8D22PF29062 W8D22PF29092 W8D25PF29062 W8D25PF29092 W8D28PF29062 W8D28PF29092 W8D30PF29062 W8D30PF29092 W8D35PF29062 W8D35PF29092 W8D36PF29062 W8D36PF29092 W8D40PF29062 W8D40PF29092 W8D43PF29062 W8D43PF29092 W8D45PF29062 W8D45PF29092 W8D50PF29062 W8D50PF29092 W8D60PF29062 W8D60PF29092 W8D18PF29063 W8D18PF29093 W8D20PF29063 W8D20PF29093 W8D22PF29063 W8D22PF29093 W8D25PF29063 W8D25PF29093 W8D28PF29063 W8D28PF29093 W8D30PF29063 W8D30PF29093 W8D35PF29063 W8D35PF29093 W8D36PF29063 W8D36PF29093 W8D40PF29063 W8D40PF29093 W8D43PF29063 W8D43PF29093 W8D45PF29063 W8D45PF29093 W8D50PF29063 W8D50PF29093 W8D60PF29063 W8D60PF29093 Tail Length .180 [4.57] (DIM “J”) 18 20 22 25 28 30 35 36 40 43 45 50 60 136 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline, Press-Fit without Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [3.37 to 1.80] .120±.003 [3.05±.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB—5 lbs. [356 N] Insertion/Withdrawal Force— 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. Electrical Properties: Operating Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 .100 [2.54] .550 [13.97] J Application Tooling: .100 [2.54] Insertion Tool—page 150 .025 Sq. Typ. [.64] C Related Product Data: Daughter Card Edge Pattern— page 57 .040±.003 [1.02±.08] Dia. Dim C .200 [5.08] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .100 [2.54] 137 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100" [2.54] Centerline / .200" [5.08] Row-to-Row without Standoffs No. of Dual Readout Positions Dimensions A B C .300 [7.62] Card Slot Depth Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 C8D06PF29032 C8D06PF29142 C8D06PF29022 C8D10PF29032 C8D10PF29142 C8D10PF29022 C8D12PF29032 C8D12PF29142 C8D12PF29022 C8D15PF29032 C8D15PF29142 C8D15PF29022 C8D20PF29032 C8D20PF29142 C8D20PF29022 C8D22PF29032 C8D22PF29142 C8D22PF29022 C8D25PF29032 C8D25PF29142 C8D25PF29022 C8D28PF29032 C8D28PF29142 C8D28PF29022 C8D30PF29032 C8D30PF29142 C8D30PF29022 C8D31PF29032 C8D31PF29142 C8D31PF29022 C8D35PF29032 C8D35PF29142 C8D35PF29022 C8D36PF29032 C8D36PF29142 C8D36PF29022 C8D40PF29032 C8D40PF29142 C8D40PF29022 C8D43PF29032 C8D43PF29142 C8D43PF29022 C8D50PF29032 C8D50PF29142 C8D50PF29022 C8D60PF29032 C8D60PF29142 C8D60PF29022 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 C8D06PF29033 C8D06PF29143 C8D06PF29023 C8D10PF29033 C8D10PF29143 C8D10PF29023 C8D12PF29033 C8D12PF29143 C8D12PF29023 C8D15PF29033 C8D15PF29143 C8D15PF29023 C8D20PF29033 C8D20PF29143 C8D20PF29023 C8D22PF29033 C8D22PF29143 C8D22PF29023 C8D25PF29033 C8D25PF29143 C8D25PF29023 C8D28PF29033 C8D28PF29143 C8D28PF29023 C8D30PF29033 C8D30PF29143 C8D30PF29023 C8D31PF29033 C8D31PF29143 C8D31PF29023 C8D35PF29033 C8D35PF29143 C8D35PF29023 C8D36PF29033 C8D36PF29143 C8D36PF29023 C8D40PF29033 C8D40PF29143 C8D40PF29023 C8D43PF29033 C8D43PF29143 C8D43PF29023 C8D50PF29033 C8D50PF29143 C8D50PF29023 C8D60PF29033 C8D60PF29143 C8D60PF29023 Tail Length .670 [17.02] (“J”) 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 Tail Length .180 [4.57] (“J”) 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 138 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .100 x .200 [2.54 x 5.08] Centerline, Press-Fit with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120±.003 [3.05±.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB—5 lbs. [356 N] Insertion/Withdrawal Force— 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. .100 [2.54] Electrical Properties: Operating Voltage—600 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .610 [15.49] Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 J .100 [2.54] .025 Sq. [.64] C Application Tooling: Insertion Tool—page 150 .040±.003 [1.02±.08] Dia. Related Product Data: Dim C Daughter Card Edge Pattern— page 57 .200 [5.08] .100 [2.54] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 139 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .100 [2.54] Center-to-Center/.200 [5.08] Row-To-Row with Standoffs Dimensions No. of Dual Readout Positions A B C 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 0.860 21.84 1.260 32.00 1.460 37.08 1.760 44.70 2.260 57.40 2.460 62.48 2.760 70.10 3.060 77.72 3.260 82.80 3.360 85.34 3.760 95.50 3.860 98.04 4.260 108.20 4.560 115.82 5.260 133.60 6.260 159.00 0.700 17.78 1.100 27.94 1.300 33.02 1.600 40.64 2.100 53.34 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 3.200 81.28 3.600 91.44 3.700 93.98 4.100 104.14 4.400 111.76 5.100 129.54 6.100 154.94 0.500 12.70 0.900 22.86 1.100 27.94 1.400 35.56 1.900 48.26 2.100 53.34 2.400 60.96 2.700 68.58 2.900 73.66 3.000 76.20 3.400 86.36 3.500 88.90 3.900 99.06 4.200 106.68 4.900 124.46 5.900 149.86 Acquired Part Numbers .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth Tail Length .670 [17.02] (dim “J”) 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 C8D06PF29012 C8D06PF29132 C8D06PF29042 C8D10PF29012 C8D10PF29132 C8D10PF29042 C8D12PF29012 C8D12PF29132 C8D12PF29042 C8D15PF29012 C8D15PF29132 C8D15PF29042 C8D20PF29012 C8D20PF29132 C8D20PF29042 C8D22PF29012 C8D22PF29132 C8D22PF29042 C8D25PF29012 C8D25PF29132 C8D25PF29042 C8D28PF29012 C8D28PF29132 C8D28PF29042 C8D30PF29012 C8D30PF29132 C8D30PF29042 C8D31PF29012 C8D31PF29132 C8D31PF29042 C8D35PF29012 C8D35PF29132 C8D35PF29042 C8D36PF29012 C8D36PF29132 C8D36PF29042 C8D40PF29012 C8D40PF29132 C8D40PF29042 C8D43PF29012 C8D43PF29132 C8D43PF29042 C8D50PF29012 C8D50PF29132 C8D50PF29042 C8D60PF29012 C8D60PF29132 C8D60PF29042 C8D06PF29013 C8D06PF29133 C8D06PF29043 C8D10PF29013 C8D10PF29133 C8D10PF29043 C8D12PF29013 C8D12PF29133 C8D12PF29043 C8D15PF29013 C8D15PF29133 C8D15PF29043 C8D20PF29013 C8D20PF29133 C8D20PF29043 C8D22PF29013 C8D22PF29133 C8D22PF29043 C8D25PF29013 C8D25PF29133 C8D25PF29043 C8D28PF29013 C8D28PF29133 C8D28PF29043 C8D30PF29013 C8D30PF29133 C8D30PF29043 C8D31PF29013 C8D31PF29133 C8D31PF29043 C8D35PF29013 C8D35PF29133 C8D35PF29043 C8D36PF29013 C8D36PF29133 C8D36PF29043 C8D40PF29013 C8D40PF29133 C8D40PF29043 C8D43PF29013 C8D43PF29133 C8D43PF29043 C8D50PF29013 C8D50PF29133 C8D50PF29043 C8D60PF29013 C8D60PF29133 C8D60PF29043 Tail Length .180 [4.57] (dim “J”) 6 10 12 15 20 22 25 28 30 31 35 36 40 43 50 60 140 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .125 x .250 [3.18 x 6.35] Centerline without Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120±.003 [3.05±.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB—5 lbs. [356 N] Insertion/Withdrawal Force— 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .250 [6.35] A B C Electrical Properties: Operating Voltage—1000 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .020 [.51] Contact Gap .365 [9.27] .125 [3.18] .550 [13.97] Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 J .125 [3.18] Application Tooling: .025 Sq. Typ. [.64] C Insertion Tool—page 150 Related Product Data: Daughter Card Edge Pattern— page 57 .040±.003 [1.02±.08] Dia. Dim C .250 [6.35] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .125 [3.18] 141 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .125 [3.18] Centerline /.250 [6.35] Row-to-Row without Standoffs Dimensions No. of Dual Readout Positions Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth A B C .300 [7.62] Card Slot Depth 1.035 26.29 1.535 38.99 1.785 45.34 2.160 54.86 2.535 64.39 2.785 70.74 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 1.625 41.28 2.000 50.80 2.375 60.33 2.625 66.68 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 C7D06PF29032 C7D06PF29142 C7D06PF29022 C7D10PF29032 C7D10PF29142 C7D10PF29022 C7D12PF29032 C7D12PF29142 C7D12PF29022 C7D15PF29032 C7D15PF29142 C7D15PF29022 C7D18PF29032 C7D18PF29142 C7D18PF29022 C7D20PF29032 C7D20PF29142 C7D20PF29022 C7D22PF29032 C7D22PF29142 C7D22PF29022 C7D25PF29032 C7D25PF29142 C7D25PF29022 C7D28PF29032 C7D28PF29142 C7D28PF29022 C7D30PF29032 C7D30PF29142 C7D30PF29022 C7D31PF29032 C7D31PF29142 C7D31PF29022 C7D35PF29032 C7D35PF29142 C7D35PF29022 C7D36PF29032 C7D36PF29142 C7D36PF29022 C7D40PF29032 C7D40PF29142 C7D40PF29022 C7D43PF29032 C7D43PF29142 C7D43PF29022 C7D50PF29032 C7D50PF29142 C7D50PF29022 1.035 26.29 1.535 38.99 1.785 45.34 2.160 54.86 2.535 64.39 2.785 70.74 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 1.625 41.28 2.000 50.80 2.375 60.33 2.625 66.68 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 C7D06PF29033 C7D06PF29143 C7D06PF29023 C7D10PF29033 C7D10PF29143 C7D10PF29023 C7D12PF29033 C7D12PF29143 C7D12PF29023 C7D15PF29033 C7D15PF29143 C7D15PF29023 C7D18PF29033 C7D18PF29143 C7D18PF29023 C7D20PF29033 C7D20PF29143 C7D20PF29023 C7D22PF29033 C7D22PF29143 C7D22PF29023 C7D25PF29033 C7D25PF29143 C7D25PF29023 C7D28PF29033 C7D28PF29143 C7D28PF29023 C7D30PF29033 C7D30PF29143 C7D30PF29023 C7D31PF29033 C7D31PF29143 C7D31PF29023 C7D35PF29033 C7D35PF29143 C7D35PF29023 C7D36PF29033 C7D36PF29143 C7D36PF29023 C7D40PF29033 C7D40PF29143 C7D40PF29023 C7D43PF29033 C7D43PF29143 C7D43PF29023 C7D50PF29033 C7D50PF29143 C7D50PF29023 Tail Length .670 [17.02] (DIM “J”) 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 50 Tail Length .180 [4.57] (DIM “J”) 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 50 142 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .125 x .250 [3.18 x 6.35] Centerline with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120±.003 [3.05±.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB—5 lbs. [356 N] Insertion/Withdrawal Force— 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] .125 [3.18] Electrical Properties: Operating Voltage—1000 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .550 [13.97] Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 J .125 [3.18] Application Tooling: .025 Sq. Typ. [.64] C Insertion Tool—page 150 Related Product Data: .040±.003 [1.02±.08] Dia. Daughter Card Edge Pattern— page 57 Dim C .250 [6.35] .125 [3.18] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. 143 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .125 [3.18] Centerline /.250 [6.35] Row-to-Row with Standoffs Dimensions No. of Dual Readout Positions Acquired Part Numbers .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth A B C .300 [7.62] Card Slot Depth 1.035 26.29 1.535 38.99 1.785 45.34 2.160 54.86 2.535 64.39 2.785 70.74 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 4.160 105.66 4.660 118.36 4.785 121.54 5.285 134.24 5.660 143.76 6.535 165.99 0.875 22.23 1.375 34.93 1.625 41.28 2.000 50.80 2.375 60.33 2.625 66.68 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 4.000 101.60 4.500 114.30 4.625 117.48 5.125 130.18 5.500 139.70 6.375 161.93 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 C7D06PF29012 C7D06PF29132 C7D06PF29042 C7D10PF29012 C7D10PF29132 C7D10PF29042 C7D12PF29012 C7D12PF29132 C7D12PF29042 C7D15PF29012 C7D15PF29132 C7D15PF29042 C7D18PF29012 C7D18PF29132 C7D18PF29042 C7D20PF29012 C7D20PF29132 C7D20PF29042 C7D22PF29012 C7D22PF29132 C7D22PF29042 C7D25PF29012 C7D25PF29132 C7D25PF29042 C7D28PF29012 C7D28PF29132 C7D28PF29042 C7D30PF29012 C7D30PF29132 C7D30PF29042 C7D31PF29012 C7D31PF29132 C7D31PF29042 C7D35PF29012 C7D35PF29132 C7D35PF29042 C7D36PF29012 C7D36PF29132 C7D36PF29042 C7D40PF29012 C7D40PF29132 C7D40PF29042 C7D43PF29012 C7D43PF29132 C7D43PF29042 C7D50PF29012 C7D50PF29132 C7D50PF29042 C7D06PF29013 C7D06PF29133 C7D06PF29043 C7D10PF29013 C7D10PF29133 C7D10PF29043 C7D12PF29013 C7D12PF29133 C7D12PF29043 C7D15PF29013 C7D15PF29133 C7D15PF29043 C7D18PF29013 C7D18PF29133 C7D18PF29043 C7D20PF29013 C7D20PF29133 C7D20PF29043 C7D22PF29013 C7D22PF29133 C7D22PF29043 C7D25PF29013 C7D25PF29133 C7D25PF29043 C7D28PF29013 C7D28PF29133 C7D28PF29043 C7D30PF29013 C7D30PF29133 C7D30PF29043 C7D31PF29013 C7D31PF29133 C7D31PF29043 C7D35PF29013 C7D35PF29133 C7D35PF29043 C7D36PF29013 C7D36PF29133 C7D36PF29043 C7D40PF29013 C7D40PF29133 C7D40PF29043 C7D43PF29013 C7D43PF29133 C7D43PF29043 C7D50PF29013 C7D50PF29133 C7D50PF29043 Tail Length .670 [17.02] (DIM “J”) 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 50 Tail Length .180 [4.57] (DIM “J”) 1.035 0.875 26.29 22.23 1.535 1.375 10 38.99 34.93 1.785 1.625 12 45.34 41.28 2.160 2.000 15 54.86 50.80 2.535 2.375 18 64.39 60.33 2.785 2.625 20 70.74 66.68 3.035 2.875 22 77.09 73.03 3.410 3.250 25 86.61 82.55 3.785 3.625 28 96.14 92.08 4.035 3.875 30 102.49 98.43 4.160 4.000 31 105.66 101.60 4.660 4.500 35 118.36 114.30 4.785 4.625 36 121.54 117.48 5.285 5.125 40 134.24 130.18 5.660 5.500 43 143.76 139.70 6.535 6.375 50 165.99 161.93 NOTE: Optional stacking designs are available (consult Tyco Electronics). 6 0.625 15.88 1.125 28.58 1.375 34.93 1.750 44.45 2.125 53.98 2.375 60.33 2.625 66.68 3.000 76.20 3.375 85.73 3.625 92.08 3.750 95.25 4.250 107.95 4.375 111.13 4.875 123.83 5.250 133.35 6.125 155.58 144 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .156 x .200 [3.18 x 5.08] Centerline without Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120±.003 [3.05±.25] Point of Contact Card Slot .300 [7.62] Depth .350 [8.89] .415 [10.54] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB— 5 lbs. [356 N] Insertion/Withdrawal Force— 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. Electrical Properties: Operating Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms Environmental Properties: Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 .156 [3.96] .550 [13.97] J Application Tooling: .156 [3.96] .025 Sq. Typ. [.64] Insertion Tool—page 150 C Related Product Data: Daughter Card Edge Pattern— page 57 .040±.003 [1.02±.08] Dia. Dim C .200 [5.08] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .156 [3.96] 145 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .156 [3.18] Centerline/.200 [5.08] Row-to-Row without Standoffs Dimensions No. of Dual Readout Positions A B C .300 [7.62] Card Slot Depth Acquired Part Numbers .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 C6D06PF29032 C6D06PF29142 C6D06PF29022 C6D10PF29032 C6D10PF29142 C6D10PF29022 C6D12PF29032 C6D12PF29142 C6D12PF29022 C6D15PF29032 C6D15PF29142 C6D15PF29022 C6D18PF29032 C6D18PF29142 C6D18PF29022 C6D20PF29032 C6D20PF29142 C6D20PF29022 C6D22PF29032 C6D22PF29142 C6D22PF29022 C6D25PF29032 C6D25PF29142 C6D25PF29022 C6D28PF29032 C6D28PF29142 C6D28PF29022 C6D30PF29032 C6D30PF29142 C6D30PF29022 C6D31PF29032 C6D31PF29142 C6D31PF29022 C6D35PF29032 C6D35PF29142 C6D35PF29022 C6D36PF29032 C6D36PF29142 C6D36PF29022 C6D40PF29032 C6D40PF29142 C6D40PF29022 C6D43PF29032 C6D43PF29142 C6D43PF29022 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 C6D06PF29033 C6D06PF29143 C6D06PF29023 C6D10PF29033 C6D10PF29143 C6D10PF29023 C6D12PF29033 C6D12PF29143 C6D12PF29023 C6D15PF29033 C6D15PF29143 C6D15PF29023 C6D18PF29033 C6D18PF29143 C6D18PF29023 C6D20PF29033 C6D20PF29143 C6D20PF29023 C6D22PF29033 C6D22PF29143 C6D22PF29023 C6D25PF29033 C6D25PF29143 C6D25PF29023 C6D28PF29033 C6D28PF29143 C6D28PF29023 C6D30PF29033 C6D30PF29143 C6D30PF29023 C6D31PF29033 C6D31PF29143 C6D31PF29023 C6D35PF29033 C6D35PF29143 C6D35PF29023 C6D36PF29033 C6D36PF29143 C6D36PF29023 C6D40PF29033 C6D40PF29143 C6D40PF29023 C6D43PF29033 C6D43PF29143 C6D43PF29023 .670 [17.02] Tail Length (DIM “J”) 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 .180 [4.57] Tail Length (DIM “J”) 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 146 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) .156 x .200 [3.18 x 5.08] Centerline with Standoffs Product Facts Recognized under the Component Program of Underwriters Laboratories Inc., File No. E60980 ■ Certified by Canadian Standards Association, File No. LR49571 ■ Accepts .054 to .071 Thk. PC Board [1.37 to 1.80] .120±.003 [3.05±.25] Point of Contact .300 [7.62] Card Slot .350 [8.89] Depth .415 [10.54] Physical Properties: Insulation Resistance— 5000 megohms minimum. Contact Retention Into PCB—5 lbs. [356 N] Insertion/Withdrawal Force— 8 oz./2 oz. [35.6 N/ 8.9 N] average contact pair using .0620 [1.57] steel blade. Insulator Body—Glass filled thermoplastic, UL rating 94V-O Color—Black Contacts—High strength copper alloy. Contact Plating—.000050 [0.00127] nickel underplate with .000030 [0.00076] gold in the mating area, tin/lead on tails, .000100 [0.00254] minimum J .200 [5.08] A B C .020 [.51] Contact Gap .365 [9.27] Ref. Electrical Properties: Operating Voltage—1500 VDC (sea level) Current Rating—3 Amperes Initial Contact Resistance— 10 milliohms .156 [3.96] Environmental Properties: .610 [15.49] Operating Temperature— -55˚C to +125˚C Temperature Cycling— MIL-STD-202 method 107 Vibration— MIL-STD-202, method 204 J .156 [3.96] Application Tooling: Insertion Tool—page 150 .025 Sq. Typ. [.64] C Related Product Data: Daughter Card Edge Pattern— page 57 .040±.003 [1.02±.08] Dia. Dim C .200 [5.08] Note: Open ends and open/closed ends are available. Consult Tyco Electronics. .156 [3.96] 147 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Ordering Information .156 [3.18] Centerline/.200 [5.08] Row-to-Row with Standoffs Dimensions No. of Dual Readout Positions A B C 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 1.221 31.01 1.845 46.86 2.157 54.79 2.625 66.68 3.093 78.56 3.405 86.49 3.717 94.41 4.185 106.30 4.653 118.19 4.965 126.11 5.121 130.07 5.745 145.92 5.901 149.89 6.525 165.74 6.993 177.62 1.100 27.94 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.284 83.41 3.596 91.34 4.064 103.23 4.532 115.11 4.844 123.04 5.000 127.00 5.624 142.85 5.780 146.81 6.404 162.66 6.872 174.55 0.780 19.81 1.404 35.66 1.716 43.59 2.184 55.47 2.652 67.36 2.964 75.29 3.276 83.21 3.744 95.10 4.212 106.98 4.524 114.91 4.680 118.87 5.304 134.72 5.460 138.68 6.085 154.56 6.552 166.42 Acquired Part Numbers .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth .670 [17.02] Tail Length (DIM “J”) 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 C6D06PF29012 C6D06PF29132 C6D06PF29042 C6D10PF29012 C6D10PF29132 C6D10PF29042 C6D12PF29012 C6D12PF29132 C6D12PF29042 C6D15PF29012 C6D15PF29132 C6D15PF29042 C6D18PF29012 C6D18PF29132 C6D18PF29042 C6D20PF29012 C6D20PF29132 C6D20PF29042 C6D22PF29012 C6D22PF29132 C6D22PF29042 C6D25PF29012 C6D25PF29132 C6D25PF29042 C6D28PF29012 C6D28PF29132 C6D28PF29042 C6D30PF29012 C6D30PF29132 C6D30PF29042 C6D31PF29012 C6D31PF29132 C6D31PF29042 C6D35PF29012 C6D35PF29132 C6D35PF29042 C6D36PF29012 C6D36PF29132 C6D36PF29042 C6D40PF29012 C6D40PF29132 C6D40PF29042 C6D43PF29012 C6D43PF29132 C6D43PF29042 C6D06PF29013 C6D06PF29133 C6D06PF29043 C6D10PF29013 C6D10PF29133 C6D10PF29043 C6D12PF29013 C6D12PF29133 C6D12PF29043 C6D15PF29013 C6D15PF29133 C6D15PF29043 C6D18PF29013 C6D18PF29133 C6D18PF29043 C6D20PF29013 C6D20PF29133 C6D20PF29043 C6D22PF29013 C6D22PF29133 C6D22PF29043 C6D25PF29013 C6D25PF29133 C6D25PF29043 C6D28PF29013 C6D28PF29133 C6D28PF29043 C6D30PF29013 C6D30PF29133 C6D30PF29043 C6D31PF29013 C6D31PF29133 C6D31PF29043 C6D35PF29013 C6D35PF29133 C6D35PF29043 C6D36PF29013 C6D36PF29133 C6D36PF29043 C6D40PF29013 C6D40PF29133 C6D40PF29043 C6D43PF29013 C6D43PF29133 C6D43PF29043 .180 [4.57] Tail Length (DIM “J”) 6 10 12 15 18 20 22 25 28 30 31 35 36 40 43 148 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Press-Fit Application Tooling Tyco Electronics offers a complete line of servo-electric driven presses for the application of press-fit connectors. Each system features a PC controlled servo electric drive for precise application and monitoring of force, speed, and press height. The entire process is data driven to provide flexible programming and automatic set-up. SPC analysis is provided for each connector pressed to assure the quality of every application. BMEP 1K/2K Servo Electric Press • 1000 or 2000 lb force [4.5 or 9 kN] • 12” [305 mm] throat depth • Compact footprint – 16” x 24” [406 x 610 mm] • Force resolution of approximately 1 lb [4.4 N] for delicate press applications. BMEP 3T/5T Benchtop Electric Servo Press • 3 or 5 tons force [27 or 44 kN] • 18” x 24” [460 x 610 mm] PCB capacity • Compact footprint – 24” x 48” [610 x 1220 mm] • Midrange force and board size capacity in a benchtop unit. MEP 6T/12 T Manual Electric Servo Press • 6 or 12 tons force [53 or 107 kN] • 24” x 36” [610 x 914 mm] PCB capacity • Self-contained, portable unit • Compact, manual unit capable of handling large boards and high force applications. Automatic Pick, Place and Press (AP3) • 8 tons force [71 kN] • 18” x 30” [457 x 762 mm] PCB capacity • SMEMA compatible unit for automatic pick, place and press of connectors and odd-from components. • Vision system for pin inspection prior to placement. 149 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Press-Fit Card Edge Insertion Tools Ordering Information Tool Part Number Acquired P/N TYCO Replacement Blade Part Number Acquired P/N Tyco Center-to Center Connector Prefix Max. No. Of Positions .100 x .100 2.54 x 2.54 .100 x .100 2.54 x 2.54 .156 x .200 3.96 x 5.08 .125 x .250 3.18 x 6.35 .100 x .200 2.54 x 5.08 .100 x .200 2.54 x 5.08 (Full Scoop) .100 x .200 2.54 x 5.08 (Full Scoop) C1 70 98336 3-1437266-5 98293 1437274-1 C1 100 98341 — 98293 1437274-1 C6 43 98231 1-1437266-1 98206 1437266-8 C7 50 98230 1-1437266-0 98206 1437266-8 C8 70 98224 1-1437266-9 98206 1437266-8 W8 70 98236 1-1490560-1 98238 1490563-1 W8 35 98236 1-1490560-2 98238 1490563-1 150 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Press-Fit Card Edge Removal Tool Kits Description Removal tool kits include: impact tools, removal tips for tail lengths ranging from .180 in. [4.57] to .680 in. [17.27] Kits for .100" x .200" [2.54 x 5.08] Series Card Edge connectors include the insertion tip. Ordering Information Center x Row .156 x .200 3.96 x 5.08 .125 x .250 3.18 x 6.35 .100 x .200 2.54 x 5.08 .100 x .100 2.54 x 2.54 .100 x .200 2.54 x 5.08 Wide Full Scoop Prefix Acquired Kit Number Tyco Kit Number C6 9818002 1437266-3 C7 9818002 1437266-3 C8 9818002 1437266-3 C1 9818004 1437266-4 W8 9818005 1437266-5 Ordering Information Item No. 1 2 3 4 6 10 11 12 Description Impact Tool Removal Tip - .180 [4.57] Tail Removal Tip - .378/.475 Tail 9.60/12.07 Removal Tip - .670/.680 Tail 17.02/17.27 Insertion Tip - C6, 7 & 8 PF Removal Tip - .550/.625 Tail 13.97/15.88 Insertion Tip - C1 Series PF Insertion Tip - W8 Series PF 9818001 √ √ Applies to Kit No. 9818001 9818003 9818004 Replacement Tyco Part Part 9818005 Number Number √ √ √ √ √ √ √ √ 9820401 9820301 1437266-7 1437266-6 √ √ √ √ 9820302 1437260-4 √ √ √ √ 9820303 √ — 9836701 3-1437266-9 √ √ √ 9820305 1437260-5 9836301 9836702 1437260-6 1437260-7 151 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Wire-to-Board Connectors Except for DUO-TYNE flag connectors, which are exclusively for wire-to-board application, the connectors presented in this section are primarily wire-to-board connectors, but do have some board-to-board capabilities. These connectors are available in a wide range of styles to suit almost any wire-to-board application. This versatile connector family features snap-in contacts of various configurations including crimp, post, eyelet and solder types. Wire-to-board crimp, snap-in contacts are easily inserted into the connector housing and are furnished in reel-fed strip form for automatic machine application and loose piece for hand tool termination. The Wire-to-Board Printed Circuit Board Connector family includes: Crimp Snap Twin Leaf Connectors High Current Connectors DUO-TYNE Flag Connectors (Pages 173-176) (Pages 177-180) (Pages 154-163) Designed for a current capability of up to 30 amperes, these connectors are an economical answer to the costly problem of interconnecting high current printed circuitry. Styles are available for wire-to-board and board-to-board applications. Contacts are on .312 [7.92] centers. These economical connectors are designed to meet the quality and reliability requirements of industries such as appliance controls, vending machine subasemblies, television, stereo, business machines and other areas with similar control needs. The right-angle design of the connector permits close-quarter cabling. Contacts are doubly locked in when a PC board is inserted. These connectors are designed for high density wire-to-board applications and feature bifurcated, crimp and solder eyelet contacts on .100 [2.54] and .125 [3.18] centers. Design flexibility allows the customer to save by purchasing only enough contacts for his circuit design requirements. Contact styles include crimp, solder eyelet and vertical and right-angle posts, in a variety of sizes. AMP-LEAF Connectors (Pages 164-172) These connectors are for single- or double-sided printed circuit boards. Snap-in contacts lock in place on .156 [3.96] centers, maintaining constant pressure on circuit paths. Contact options are available for precision crimped terminations and solder dip applications. 152 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Wire-to-Board Connector Selection Guide Crimp Snap Twin Leaf Connectors (Pages 154-163) .175 [4.45] AMP-LEAF Connectors (Pages 164-172) .350 [8.89] .437 [11.10] .340 .350 .360 .375 .437 .485 .087 [2.21] .750 [19.05] [8.64] [8.89] [9.14] [9.53] [11.10] [12.32] .700 [17.78] .405 [10.29] .375 [9.53] Centerlines .100 [2.54] .125 [3.18] .156 [3.96] .197 [5.00] .260 [6.60] .312 [7.92] X X X X X X X X X X X X X X X X X X Styles Crimp Right-Angle Post Wrap-Type Post Solder Eyelet Solder Tail Double Sided Single Sided High Current Connectors (Pages 173-176) DUO-TYNE Flag Connectors (Pages 177-180) .437 [11.10] .578 [14.68] .375 [9.53] .200 [5.08] .012 [0.30] .967 [24.56] .500 [12.70] .567 [14.40] .240 [6.10] Centerlines .100 [2.54] .125 [3.18] .156 [3.96] .197 [5.00] .260 [6.60] .312 [7.92] X X Styles Crimp Right-Angle Post Wrap-Type Post Solder Eyelet Solder Tail Double Sided Single Sided X X X X X* *Double-sided board; single readout. Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. 153 Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors Product Facts ■ Crimp snap-in, solder eyelet, .025 [0.64] square posted and right angle contacts on .100 [2.54], .125 [3.18] or .156 [3.96] centers ■ Customer buys only enough contacts to meet circuit and retention requirements ■ Contacts bifurcated for redundancy ■ Single leaf version available for higher contact normal forces ■ Low insertion forces ■ Accommodates AWG 16-28 [1.4-0.08 mm2] wire range and insulation diameters .035-.105 [0.89-2.67] ■ Large variety of connector sizes ■ Cavity identification on face of card slot and wire entry ■ High speed automatic machine terminations provide uniform reliability at lowest applied cost ■ Recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 ■ Certified by Canadian Standards Association File No. LR 7189 The Crimp Snap Twin Leaf Connector is designed especially for high density wire-to-board applications. Termination styles include crimp, solder, posted and right angle, in a variety of sizes. Design flexibility allows the customer to save by purchasing only enough contacts for the circuit requirements. Easy replaceability of each contact cuts repair cost in the event of contact or wire damage. Performance Specifications Contact Rating*: 5 amperes, continuous 3 amperes, max. (for .025 [0.64] posted contacts) Contact Resistance: 10 milliohms, max. Insulation Resistance: 5000 megohms (initial) 1000 megohms Voltage Rating: .100 [2.54] Centerline-1000 Vrms .125 [3.18] Centerline-1500 Vrms .156 [3.96] Centerline-1800 Vrms Insertion Force (per pair): Twin Leaf-10 oz. [2.78 N], max.; 7.6 oz. [2.11 N], avg. Non-Bifurcated Contacts20 oz. [5.57 N], max. Extraction Force (per pair): Twin Leaf-0.7 oz. [0.195 N], min.; 1.2 oz. [0.334 N], avg. Operating Temperature: -55°C to +105°C *Consult Tyco Electronics engineering when paralleling contacts for power applications. 154 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors Crimp, Snap-In Contacts (Continued) .104 [2.64] .705 [17.91] .060 [1.52] Material and Finish: Phosphor bronze, plated .000030 [0.00076] nickel on entire contact, with the addition of one of the following platings: Plating A—.000030 [0.00076] gold in mating area Plating B—.000015 [0.00038] gold in mating area Plating C—.000050 [0.00127] gold in mating area, with gold flash on remainder of contact Plating D—.000015 [0.00038] gold in mating area, with gold flash on remainder of contact .705 [17.91] Connector Centerline Performance Specifications— page 154 Application Tooling—pages 184,185 Connector Housings—pages 157, 159, 161 22-18 0.3-0.9 Insulation Contact Dia. Range (PFliantiisnhg) A .035-.055 B 0.89-1.40 C D A .048-.060 B 1.22-1.52 C D A .035-.055 B 0.89-1.40 C D A .048-.060 B 1.22-1.52 C D A .049-.095 B 1.24-2.41 C 20-16 0.6-1.4 .073-.090 1.85-2.29 28-24 0.08-0.2 .035-.055 0.89-1.40 24-20 0.2-0.6 .048-.060 1.22-1.52 22-18 0.3-0.9 .049-.095 1.24-2.41 20-16 0.6-1.4 .073-.090 1.85-2.29 .085-.105 2.16-2.67 28-24 0.08-0.2 .100 2.54 24-20 0.2-0.6 Note: Tin plating is available upon request. Related Product Data: Wire Size Range AWG/mm2 28-24 0.08-0.2 .125 3.18 Technical Documents: 24-20 0.2-0.6 (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheets 408-7527, 408-7529, 408-7531, 408-7551, 408-7556, 408-7583 .156 3.96 .030 [0.76] Note: Only loose piece contacts manufactured and supplied by Tyco Electronics are to be used with the hand tools listed on this page. No attempt should be made to produce loose piece parts from a strip since special cutoff tooling is required to assure a properly functioning part. A C A B C D A B C D A B C A C B Applicator for Applicator for Contact Part Numbers AMP-O-LECTRIC Stripper/Crimper Loose Piece Strip Form Machine* Machine 583616-4 583616-2 583616-5 583616-3 466577-4 466912-1 583616-9 583616-8 1-583616-1 1-583616-0 583853-5 583853-3 583853-4 583853-2 466622-2 466919-1 583853-9 583853-8 1-583853-1 1-583853-0 583616-4 583616-2 583616-5 583616-3 466577-4 466912-1 583616-9 583616-8 1-583853-1 1-583853-0 583853-5 583853-3 583853-4 583853-2 466622-2 466919-1 583853-9 583853-8 1-583853-1 1-583853-0 583649-6 583649-3 583649-5 583649-2 466713-2 466928-1 583649-7 583649-4 583875-6 583875-5 687775-2 — 583875-3 583875-2 583616-4 583616-2 583616-5 583616-3 466577-4 466912-1 583616-9 583616-8 1-583616-1 1-583616-0 583853-5 583853-3 583853-4 583853-2 466622-2 466919-1 583853-9 583853-8 1-583853-1 1-583853-0 583649-6 583649-3 583649-5 583649-2 466713-2 466928-1 583649-7 583649-4 583875-6 583875-5 687775-2 — 583875-3 583875-2 583875-3 —vvv — .060 [1.52] Material and Finish: Phosphor bronze, plated .000030 [0.00076] nickel on entire contact, with the addition of one of the following platings: Plating A—.000030 [0.00076] gold in mating area Plating B—.000015 [0.00038] gold in mating area Note: Tin plating is available upon request. Related Product Data: (See above) Catalog 1654080 Issued 7-03 www.tycoelectronics.com Connector Centerline .100 2.54 .125 3.18 .156 3.96 Wire Size Range AWG/mm2 28-24 0.08-0.2 24-20 0.2-0.6 28-24 0.08-0.2 24-20 0.2-0.6 22-18 0.3-0.9 28-24 0.08-0.2 24-20 0.2-0.6 22-18 0.3-0.9 Hand Tool Orange 90268-1 Green 91535-1 Orange 90268-1 Green 91535-1 Violet 90264-1 White 90285-1 Orange 90268-1 Green 91535-1 Violet 90264-1 White 90285-1 — .104 [2.64] .705 [17.91] .705 [17.91] Crimp, Snap-In Contacts, Non-Bifurcated Color Code .030 [0.76] Applicator for Applicator for Contact Part Numbers Insulation Contact AMP-O-LECTRIC Stripper/Crimper Dia. Range (PFliantiisnhg) Loose Piece Strip Form Machine* Machine .035-.055 A 531476-5 531476-4 466577-4 466912-1 0.89-1.40 .048-.060 A 531477-5 531477-4 466622-2 466919-1 1.22-1.52 B 531477-4 531477-2 .035-.055 A 531476-5 531476-4 466577-4 466912-1 0.89-1.40 .048-060 A 531477-5 531477-4 466622-2 466919-1 1.22-1.52 B 531477-3 531477-2 .045-.095 A — 531478-4 466713-2 466928-1 1.14-2.41 .035-.055 A 531476-5 531476-4 466577-4 466912-1 0.89-1.40 B 531477-5 — .048-.060 A 531477-5 531477-4 466622-2 466919-1 1.22-1.52 B 531477-3 531477-2 .045-.095 A — 531478-4 466713-2 466928-1 1.14-2.41 Color Code Hand Tool Orange 90268-1 Green 91535-1 Orange 90268-1 Green 91535-1 Violet 90264-1 Orange 90268-1 Green 91535-1 Violet — *Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench machines and lead-making machines. Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 155 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors (Continued) Snap-In Solder Eyelet Contacts Material and Finish: .060 [1.52] Phosphor bronze, plated .000030 [0.00076] nickel on entire contact, with the addition of one of the following platings: Plating A—.000030 [0.00076] gold in mating area Plating B—.000015 [0.00038] gold in mating area Solder eyelet portion is tin plated. .104 .030 [2.64] [0.76] Note: Tin plating of entire contact is available upon request. Related Product Data: Connector Centerline Performance Specifications— page 154 Connector Housings—pages 157, 159, 161 .100 2.54 .125 3.18 Contact Finish (Plating) A B Part Numbers A 530245-3 Dimension L Part Numbers .451 11.46 .535 13.59 .525 13.34 .525 13.34 583879-1 583854-3 583854-5 Technical Documents (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheets 408-7527, 408-7529 Snap-In Wrap Post Contacts .025 [0.64] Square Material and Finish: L Contact—Phosphor bronze, plated .000015 [0.00038] gold in mating area, with entire contact underplated .000030 [0.00076] nickel Post—Phosphor bronze, tin-plated Connector Centerline Spacing Note: Tin plated contacts are available upon request. .100 2.54 Related Product Data: Performance Specifications— page 154 Connector Housings—pages 157, 159, 161 .125 3.18 .156 3.96 583879-4 583884-1 583884-1 Contact Extraction Tool Hand Tool Technical Documents: (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheets 408-7527, 408-7529 156 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors, .100 [2.54] Centerline With Mounting Ears Housings Material: Black glass-filled polyester, 94V-O rated .128 [3.25] Dia. 2 Holes .100 [2.54] Without Mounting Ears .100 [2.54] Fit for .055-.070 [1.40-1.78] PC Board .300 [7.62] .100 [2.54] .100 [2.54] Fit for .055-.070 [1.40-1.78] PC Board Related Product Data: Performance Specifications— page 154 Contacts—pages 155, 156 Accessories—page 162* PCB Edge Pattern—page 163 .175 [4.45] A D .550 [13.97] E B Technical Documents: B .750 [19.05] (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheet 408-7527 A .350 [8.89] No. of Dual Positions A B .250 [6.35] D E — 1.175 29.85 — 1.430 36.32 — .700 17.78 .900 22.86 .720 18.29 7 .800 20.32 .900 22.86 1.000 25.4 1.100 27.94 .820 20.83 .920 23.36 8 10 13 14 15 17 18 20 C Dimensions C 6 1.100 27.94 1.300 33.02 1.120 28.49 1.200 30.48 1.500 38.1 1.400 35.56 1.700 43.16 1.600 40.64 1.520 38.61 1.600 40.64 1.800 45.72 1.620 41.15 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 2.000 50.8 2.100 53.34 2.300 58.42 2.500 63.50 2.800 71.12 1.820 46.30 1.920 48.76 2.120 53.84 2.320 58.93 2.620 66.55 .400 [10.16] .750 [19.05] .345 [8.76] C .350 [8.89] Part Numbers Without With Mounting Ears Mounting Ears 2-583717-1 — — 1-583861-5 — 2-583717-3 — — — 3-583717-9 — 1.700 43.18 1.575 40.01 2.100 53.34 1.830 46.48 1-583717-1 1-583718-1 — 1-583861-7 — — 3-583717-3 — — — 2-583717-7 — 2.200 55.88 2.075 52.71 2.400 60.96 2.600 66.04 2.330 59.18 2.800 71.12 1-583717-3 1-583718-3 — 1-583861-9 1-583717-5 1-583861-1 — — 1-583717-7 — — — 3-583717-1 — 1-583717-9 1-583718-9 1-583717-1 1-583718-1 1-583717-3 1-583718-3 — 1-583861-1 — 2-583718-7 — 2-583861-5 — 1-583718-5 — 1-583861-3 1-583717-9 1-583718-7 — 2-583861-1 2.900 3.300 22 73.66 83.82 3.200 3.600 25 81.28 91.44 3.700 4.100 93.98 104.14 3.100 3.300 3.120 30 78.74 83.82 79.25 3.575 3.830 90.81 97.28 3.300 3.500 3.320 3.900 4.300 32 83.82 88.90 84.33 99.06 190.22 3.700 3.900 3.720 4.175 4.430 36 93.98 93.06 94.49 106.04 112.52 4.700 5.100 119.38 129.54 4.100 4.300 4 .120 40 104.14 109.22 104.65 4.575 4.830 116.21 122.68 5.700 6.100 144.78 154.94 5.100 5.300 5.120 50 129.54 134.62 130.05 5.575 5.830 141.61 148.08 Note: Other connector sizes can be made available, consult Tyco Electronics. 157 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors, .100 [2.54] Centerline Housings Preloaded with Right-Angle Posts Fit for .055-.070 [1.40-1.78] PC Board With Mounting Ears .350 [8.89] Material and Finish: A (Continued) Without Mounting Ears A .128 Dia. [3.25] Typ. .300 [7.62] .350 [8.89] Housing—Black glass-filled polyester, 94V-O rated Contacts—Phosphor bronze, plated .000015 [0.00038] gold in mating area, with entire contact underplated .000030 [0.00076] nickel Posts—Phosphor bronze, tin plated .100 [2.54] .100 Typ. [2.54] .100 [2.54] Intercontact Keying Slot Typ. .100 Typ. [2.54] .750 [19.05] B .550 [13.97] Related Product Data: Performance Specifications— page 154 Asccessories—page 162* PCB Edge Pattern and Hole Layout—page 163 B .400 [10.16] .345 [8.76] .250 [6.35] .750 [19.05] .170 [4.32] .125 [3.17] G Technical Documents: .025 [.064] Square Post Tin-Plated (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheet 408-7527 C C .150 [3.81] F Min. E D D .128 Dia. [3.25] (2 Plcs.) E B C Connector Centerline Spacing .038 Dia. Typ. [0.97] A No. of Dual Pos. 10 17 22 25 28 30 50 Recommended PC Board Hole Layout Type II Type I A B 1.100 27.94 1.800 45.72 2.300 58.42 2.600 66.04 2.900 73.66 3.100 78.74 5.100 129.54 1.300 33.02 2.000 50.80 2.500 63.50 2.800 71.12 3.100 78.74 3.200 81.28 5.300 134.62 Dimensions C D 1.120 28.49 1.820 46.23 2.320 58.93 2.620 66.55 2.920 74.16 3.120 79.25 5.120 130.05 1.575 40.01 — E F G Posted Assembly Part Numbers Right-Angle Post Right-Angle Post With Mounting Ears Without Mounting Ears Type I Type II 1.830 46.48 — — — 1-583900-5 — — .090 2.29 .090 2.29 .090 2.29 .090 2.29 .090 2.29 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 — — 1-530218-5 — 1-583900-3 1-530218-9 583900-1 — 1-530218-1 — 2-583900-6 — — 1-583900-4 1-530218-6 — — 583900-3 — — 2.900 3.300 73.66 83.82 3.200 3.600 81.28 91.44 3.375 3.630 85.72 92.20 3.700 4.100 93.98 104.14 5.575 5.830 141.61 148.08 Note: Other connector sizes can be made available, consult Tyco Electronics. 158 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors, .125 [3.18] Centerline With Mounting Ears Housings Material: Black glass-filled polyester .125 [3.18] .128 Dia. [3.25] 2 Holes 94V-O rated Without Mounting Ears Fit for .055-.070 [1.40-1.78] PC Board .125 [3.18] .125 [3.18] .125 [3.18] Fit for .055-.070 [1.40-1.78] PC Board Related Product Data: .300 .437 [7.62][11.10] Performance Specifications— page 154 Contacts—pages 155, 156 Accessories—page 162 PCB Edge Pattern—page 163 .437 [11.10] .218 [5.54] A A .300 [7.62] D Technical Documents: (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheet 408-7527 E B .550 [13.97] B .455 [11.56] .345 [8.76] .345 [8.76] .750 [19.05] .750 [19.05] .250 [6.35] C No. of Dual Positions 6 10 15 22 25 28 30 40 44 C A B Dimensions C D E .875 22.23 1.375 34.93 2.000 50.80 2.875 73.03 3.250 82.55 3.625 92.08 3.875 98.43 5.125 130.17 5.625 142.88 1.035 26.29 1.535 38.99 2.160 54.86 3.035 77.09 3.410 86.61 3.785 96.14 4.035 102.49 5.285 134.23 5.785 146.94 .845 21.46 1.345 34.16 1.970 50.04 2.845 72.26 3.220 81.79 3.595 91.31 3.845 47.66 5.095 129.41 5.595 142.11 1.295 32.89 1.795 45.59 2.420 61.47 3.295 83.69 3.670 93.22 4.045 102.74 4.295 109.09 5.545 140.84 6.045 153.54 1.555 39.50 2.055 52.20 2.680 68.07 3.555 90.30 3.930 99.82 4.305 109.35 4.555 115.70 5.805 147.44 6.305 160.15 Part Numbers Without With Mounting Ears Mounting Ears 1-583873-1 1-583864-1 — 1-583864-3 1-583873-5 — 1-583873-9 1-583864-9 — — — 1-583864-3 — 2-583864-1 — 1-583864-7 1-583873-9 — Note: Other connector sizes can be made available, consult Tyco Electronics. 159 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors, .125 [3.18] Centerline Housings Preloaded with Right-Angle Posts With Mounting Ears Material and Finish: .125 [3.18] Housing—Black glass-filled polyester, 94V-O rated Contacts—Phosphor bronze, plated .000030 [0.00076] gold in mating area, with entire contact underplated .000030 [0.00076] nickel Posts—Phosphor bronze, tin-plated 3.875 [98.43] Fit for .055-.070 [1.40-1.78] PC Board .128 Dia. [3.25] Typ. .437±.007 [11.10±0.18] .300 [7.62] Related Product Data: Performance Specifications— page 154 Accessories—page 162 PCB Edge Pattern and Hole Layout—page 163 (Continued) .550 [13.97] .128 Dia. [3.25] .750 [19.05] .345 [8.76] .170 [4.32] .125 [3.18] .250 [6.35] 4.035 [102.49] Technical Documents: .100 [2.54] .025 [0.64] Square Post Tin-Plated .150 [3.81] .180 Min. [4.57] (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheet 408-7527 4.555 [115.70] .125 Typ. [3.18] 4.295 [109.09] 3.845 [97.66] 30 Dual Positions, Part No. 530238-8 160 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors, .156 [3.96] Centerline Housings With Mounting Ears Material: Black glass-filled polyester, 94V-O rated .156 [3.96] .160 [4.06] Related Product Data: Performance Specifications— page 154 Contacts—pages 155, 156 Accessories—page 162 PCB Edge Pattern—page 163 Fit for .055 - .070 [1.40-1.78] PC Board .128 Dia. [3.25] 2 Holes .325 .437 [8.26] [11.10] .162 [4.11] A D Technical Documents: (pages 186, 187): Product Specification 108-9031 Application Specification 114-9004 Instruction Sheet 408-7527 .345 [8.76] E B .455 [11.56] .750 [19.05] .250 [6.35] C No. of Dual Positions 6 8 10 12 15 18 22 28 36 A B Dimensions C D E 1.100 27.94 1.412 35.86 1.724 43.79 2.036 51.71 2.504 63.60 2.972 75.49 3.596 91.34 4.532 115.11 5.780 146.81 1.264 32.11 1.576 40.03 1.888 47.96 2.200 55.88 2.668 67.77 3.136 79.55 3.760 95.50 4.696 119.28 5.944 150.96 .976 24.79 1.288 32.72 1.600 40.64 1.912 48.56 2.380 60.45 2.848 72.34 3.472 88.19 4.408 111.96 5.656 143.66 1.535 38.99 1.847 46.91 2.159 54.84 2.471 62.76 2.939 74.65 3.407 86.54 4.031 102.39 4.967 126.16 6.215 157.86 1.785 45.34 2.097 53.26 2.409 61.19 2.721 69.11 3.189 81.00 3.657 92.89 4.281 108.74 5.217 132.51 6.465 164.21 Part Numbers Mounting Ears 1-583859-3 2-583859-1 1-583859-9 1-583859-5 1-583859-7 1-583859-5 1-583859-3 1-583859-1 2-583859-3 Note: Other connector sizes can be made available, consult Tyco Electronics. 161 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Accessories for Crimp Snap Twin Leaf Connectors Dummy Contacts Related Product Data: Material: Phosphor bronze The dummy contact is used in sparsely loaded housings to balance contact pressure. For specific recommendations, consult Tyco Electronincs. Tin Plated — Part No. 583857-5 .000030 [0.00076] Nickel Plated — Part No. 583857-6 Gold Flash-Over-Nickel Plate— Part No. 583857-7 Technical Documents (pages 186, 187): Instruction Sheet 408-7527 Retaining Spring Related Product Data: Material: Stainless steel Retaining springs are used for single sided PC board applications. Use one spring per 6 empty cavities. Technical Documents Unplated— Part No. 583691-2 Gold Flash-Over-Nickel Plate— Part No. 583691-3 (pages 186, 187): Instruction Sheet 408-7527 Technical Documents Keying Plugs (pages 186, 187): Instruction Sheet 408-7527 On-Contact Plug Natural Nylon— Part No. 583764-1 Intercontact Plug Natural Nylon— Part No. 583274-1 Glass-Filled Polyester— Part No. 583274-3 Locking Key Material: Nylon On-Contact Clip Part No. 530213-1 Mounting Block Kit Part No. 531250-4 Material: Natural color nylon Each kit includes 2 mounting blocks 2 self tapping screws, #5 x .437 [11.10] 2 roll pins .075 x .250 [1.57 x 6.35] .062 Dia. [1.57] Roll Pin Card Extender Connector Housing Ref. #5 Self Tapping Screws Mounting Block .062 [1.57] PC Board Ref. 162 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Crimp Snap Twin Leaf Connectors (Continued) Recommended PC Board Edge Pattern Hole for Locking Key .420 [10.67] .078 [1.98] .062 [1.57] B Min. 45°Chamfer .015 [0.38] A 45°Chamfer Connector Centerline Spacing .100 2.54 .125 3.18 .156 3.96 Dimensions Recommended PC Board Hole Layout A B .093 2.36 .118 3.00 .153 3.89 .052 1.32 .078 1.98 .094 2.39 D E B .128 Dia. [3.25] (2 Plcs.) C Connector Centerline Spacing .038 Dia. Typ. [0.97] A Connector Centerline Spacing: .100 [2.54] No. of Dual Positions 10 17 20 22 25 30 50 Dimensions C A B D E .900 22.86 1.600 40.64 1.900 48.26 2.100 53.34 2.400 60.96 2.900 73.66 4.900 124.46 .625 15.88 .475 12.07 1.575 40.01 .400 10.16 — — — — .625 15.88 .625 15.88 .625 15.88 .375 9.53 4.75 12.07 .475 12.07 2.575 65.41 2.900 73.66 3.200 81.28 3.700 93.98 5.575 141.61 .337 8.56 .337 8.56 .400 10.16 .400 10.16 .337 8.56 — — .525 13.34 .375 9.53 Connector Centerline Spacing: .125 [3.18] No. of Dual Positions A 30 3.625 92.08 B — Dimensions C — D E 4.295 109.09 .350 8.89 163 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connectors Product Facts ■ Contacts on .156 [3.96] centers ■ Glass-filled polyester, phenolic or diallyl phthalate housings ■ Closed card entry design helps prevent overstressing of contacts ■ Gold-over-nickel plated contacts ■ Locking lance permits easy contact replacement ■ Keying ■ Contacts maintain exact pressures on the circuit paths, despite repeated insertions and extractions ■ Recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 ■ Certified by Canadian Standards Association**, File No. LR 7189 **CSA certification pending for certain products, as noted. Performance Specifications Contact Current Rating*: 5.0 amperes, max. AMP-LEAF Connectors are available with crimp, snap-in contacts or preloaded with right-angle posted contacts. The crimp type printed circuit connector is supplied with the housing unloaded— the user buys only enough contacts to satisfy circuit requirements. This feature, when coupled with the Tyco Electronics matched tooling, contributes substantially to lower installed costs. Contact Engaging Force: 16 oz. [4.4 N], max. Contact Separation Force: 2 oz. [0.6 N], min. Vibration: MIL-STD-202, Method 201 Operating Temperature: Contacts –40°C to +85°C Right-angle posted connectors are supplied in various sizes, with preloaded contacts on one or both sides. The solder-type posts are formed 90° from the housing to permit right-angle interfacing between mother and daughter boards. Storage Temperature: –40°C to +85°C Housings: Glass-Filled Polyester, –55°C to +105°C Glass-Filled Phenolic, –65°C to +125°C Diallyl Phthalate, –65°C to +125°C *Consult Tyco Electronics engineering when paralleling contacts for power applications. 164 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connectors (Continued) Crimp, Snap-In Contacts Material and Finish: Phosphor bronze, plated as follows: Plating A—.000100-.000200 [0.00254-0.00508] tin (lubricant must be used) Plating B—.000030 [0.00076] min. gold in mating area, gold flash on remainder of contact, with entire contact underplated .000050 [0.00127] min. nickel Plating C—.000015 [0.00038] min. gold in mating area, gold flash on remainder of contact, with entire contact underplated .000050 [0.00127] min. nickel Plating D—.000030 [0.00076] min. gold over .000050 [0.00127] min. nickel in mating area, remainder of contact gold flash over .000015 [0.00038] min. nickel Plating E—.000030 [0.00076] min. gold in mating area, with entire contact underplated .000050 [0.00127] min. nickel Plating F—.000015 [0.00038] min. gold in mating area, with entire contact underplated .000050 [0.00127] min. nickel Related Product Data: Performance Specifications— page 164 Connector Housings— pages 167-169 Application Tooling— pages 184, 185 Wire Barrel Crimp Insulation Support Terminal Stop Locking Lance Wire Range AWG/mm2 Insulation Range Single Double Wire Wire 26-22 0.12-0.4 .050-.064 1.27-1.63 — 22-18 0.3-0.9 .055-.080 1.40-2.03 .120 3.05 Max. 16 1.25-1.40 .108 2.74 Max. .080-.160 2.03-4.06 Contact Part Numbers Loose Strip Piece Form 583990-3 583204-2 — 343371-1 — 583361-2 583989-3 583361-3 583989-4 583361-4 — 583555-4 — 583555-6 583991-3 60151-6 Applicator for Contact AMP-O-LECTRIC Finish Machine* B D A B C E F B Hand Tool 466366-2 90028-3 466367-2 90017-3 (1 #22-20) 90028-3 (2 #22) 90101-3 (1 #20) 466368-2 90031-8 (2 #18) 90101-3 (2 #20) 90101-3 (1 #16) *Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench machines and lead-making machines. Notes: 1. Shorting contacts are available, consult Tyco Electronics. Notes: 2. Contacts and housings to accommodate .093 [2.36] thick PC boards can be made available, consult Tyco Electronics. Hand Crimping Tool Contact Extraction Tool Technical Documents: Extraction Tool Number (pages 186, 187): Product Specifications 108-9013, 108-9043 Application Specification 114-9003 Instruction Sheets 408-6591, 408-7045, 408-7622, 408-7623, 408-7624, 408-7625, 408-7626 Crimp Inspection Sheet CI 8050-33 465195-1 465195-2 Dummy Contact Used with Housings 480110-2, -5 480142-2, -3 582140-5 582147-5 582264-2 582500-2 582963-2 583167-3 583280-1 583617-1 583680-1 583685-1 583722-1 583723-1 583724-1 583725-1 583726-1 480133-2 Plain Finish— Part No. 66084-1 Tin Finish— Part No. 66084-2 Gold Finish— Part No. 66084-3 Material: Phosphor bronze Technical Documents: (pages 186, 187): Instruction Sheet 408-7037 165 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connectors (Continued) .030 [0.76] Solder Eyelet Contact .120 [3.05] Material and Finish: Phosphor bronze, plated .000015 [0.00038] min. gold in contact area, gold flash on remainder of contact, with entire contact underplated .000050 [0.00127] min. nickel Contact Surfaces .100 [2.54] Locking Lance .280 [7.11] Standard Eyelet Type Contact Part No. 66067-5 (For .055-.070 [1.4-1.78] Thick PC Boards) Note: Solder tab will accommodate a maximum of two 16 AWG [1.25-1.4 mm2] solid wires, or two 18 AWG [0.8-0.9 mm2] stranded wires. Post Type Contacts .185 [4.70] Material and Finish: Phosphor bronze, plated .000015 [0.00038] min. gold in contact area, tin on post, with entire contact underplated .000050 [0.00127] min. nickel Contact Surfaces Locking Lance L Post Length L .960 24.38 .560 14.22 Loose Piece Contact Part No. (.045 x .045 [1.14 x 1.14] Post) 1-582355-3 1-582355-5 Note: Post type contacts are for .055-.070 [1.4-1.78] thick PC boards. Solder Dip Contacts For .052 [1.32] Dia. Hole Material and Finish: Phosphor bronze, plated .000015 [0.00038] min. gold in contact area or, plated .000030 [0.00076] min. gold in contact area, tin on post, with entire contact underplated .000050 [0.00127] min. nickel Contact Surfaces .120 [3.05] Locking Lance Solder Dip Contact Part No. 583294-2 (.000015) Part No. 583294-1 (.000030) (For .062 [1.57] Thick PC Board) 166 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connectors, .156 [3.96] Centerline Glass-Filled Polyester Housings A B Material: Glass-filled polyester .156 [3.96] Related Product Data: F Card Guide Assembly—page 171 PC Board Thickness—.055-.070 [1.40-1.78] Performance Specifications— page 164 Contacts—pages 165, 166 Accessories—page 171 PC Board Layout—page 172 .325 Card Slot [8.26] Depth C G .700 [17.78] H Technical Documents: (pages 186, 187): D Product Specifications 108-9013, 108-9043 Application Specification 114-9003 Instruction Sheet 408-7037 K J E Dia. (2 Holes) No. of Dual Positions A B C D Dimensions E F G 1.785 1.535 1.264 .976 .125 1.100 .456 45.34 38.99 32.11 24.79 3.18 27.94 11.58 2.409 2.159 1.888 1.600 .125 1.724 .456 10 61.19 54.84 47.96 40.64 3.18 43.79 11.58 2.721 2.471 2.200 1.912 .125 2.036 .456 12 69.11 62.76 55.88 48.56 3.18 51.71 11.58 3.189 2.939 2.668 2.380 .128 2.504 .456 15 81.00 74.65 67.77 60.45 3.25 63.60 11.58 3.657 3.407 3.136 2.848 .125 2.972 .456 18 92.89 86.54 79.65 72.34 3.18 75.49 11.58 3.657 3.407 3.136 2.848 .156 2.972 .456 18 92.89 86.54 79.65 72.34 3.96 75.49 11.58 4.281 4.031 3.760 3.472 .125 3.596 .456 22 108.74 102.39 95.50 88.19 3.18 91.34 11.58 4.281 4.031 3.760 3.472 .156 3.596 .456 22 108.74 102.39 95.50 88.19 3.96 91.34 11.58 4.749 4.499 4.228 3.940 .125 4.064 .456 25 120.62 114.27 107.39 100.01 3.18 103.23 11.58 5.529 5.279 5.008 4.720 .125 4.844 .456 30 140.44 134.09 127.20 119.89 3.18 123.04 11.58 7.015 6.578 5.942 5.722 .156 5.782 .455 36 178.18 167.08 150.92 145.33 3.96 146.86 11.55 *CSA certification pending. Note: Other connector sizes can be made available, consult Tyco Electronics. 6 H J .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .290 7.36 .300 7.62 .300 7.62 .300 7.62 .300 7.62 .300 7.62 .300 7.62 .300 7.62 .300 7.62 .300 7.62 .300 7.62 .325 8.25 K Housing Part Numbers .350 583722-1 8.89 .350 583723-1 8.89 .350 *583724-1* 8.89 .350 583680-1 8.89 .350 583725-1 8.89 .350 583725-3 8.89 .350 583617-1 8.89 .350 583617-3 8.89 .350 583726-1 8.89 .350 583685-1 8.89 .437 11.10 583552-1 167 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connectors, .156 [3.96] Centerline (Continued) Glass-Filled Phenolic Housings A B Material: Glass-filled phenolic per MIL-M-14F F Related Product Data: .156 [3.96] Card Guide Assembly—page 171 J Dia. (2 Holes) D Performance Specifications— page 164 Contacts—pages 165, 166 Accessories—page 171 PC Board Layout—page 172 Technical Documents: (pages 186, 187): Product Specifications 108-9013, 108-9043 Application Specification 114-9003 Instruction Sheet 408-7037 C G H .700 [17.78] E No. of Dual Positions 8 10 10 15 15 15 18 22 25 32 A B 1.982 50.34 2.407 61.14 1.767 44.88 2.157 54.79 C Dimensions D E 1.550 1.410 1.288 39.37 35.81 32.72 1.866 1.722 1.598 47.90 43.74 40.59 1.886 1.722 1.598 — — 47.90 43.74 40.59 3.182 2.854 2.621 2.506 2.376 80.82 72.49 66.57 63.65 60.35 3.182 2.854 2.621 2.506 2.376 80.82 72.49 66.57 63.65 60.35 3.182 2.933 2.621 2.506 2.376 80.82 74.49 66.57 63.65 60.35 3.650 3.400 3.088 2.948 2.843 92.71 86.36 78.43 74.87 72.21 4.274 4.025 3.754 3.591 3.466 108.56 102.24 95.35 91.21 88.04 4.741 4.493 4.221 4.058 3.933 120.42 114.12 107.21 103.07 99.90 6.365 5.928 5.292 5.132 5.072 161.67 150.57 134.42 130.35 128.83 F .340 8.64 .360 9.14 .360 9.14 .350 8.89 .350 8.89 .350 8.89 .375 9.52 .350 8.89 .350 8.89 .485 12.32 G H J .250 .458 .125 6.35 11.63 3.18 .250 .456 .128 6.35 11.58 3.25 — — — .250 6.35 .250 6.35 .250 6.35 .155 3.93 .250 6.35 .250 6.35 .290 7.37 .466 11.84 .466 11.84 .466 11.84 .406 10.31 .456 11.58 .456 11.58 .455 11.56 .187 4.75 .125 3.18 .128 3.25 .156 3.96 .125 3.18 .125 3.18 .187 4.75 Board Thickness Housing Part Numbers .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .084-.104 2.13-2.64 582140-5 582963-2* 583280-1 1 480110-5 1-582147-5* 1-582500-5 480133-5 480142-3 583167-3* 582264-2 2,3 *CSA certification pending. 1Housing without mounting ears. 2Housing does not accommodate intercontact keying plug. 3For .086 to .104 [2.18 to 2.64] thick PC boards (special contacts required). Note: Other connector sizes can be made available, consult Tyco Electronics. 168 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connectors, .156 [3.96] Centerline (Continued) Diallyl Phthalate Housings A B Material: Diallyl phthalate per MIL-M-14F F Related Product Data: Card Guide Assembly—page 171 Performance Specifications— page 164 Contacts—pages 165, 166 Accessories—page 171 PC Board Layout—page 172 J Dia. (2 Holes) D .156 [3.96] Technical Documents: (pages 186, 187): Product Specifications 108-9013, 108-9043 Application Specification 114-9003 Instruction Sheet 408-7037 C G H .700 [17.78] E Single Slot Housing No. of Dual Positions 15 15 18 22 A B 3.187 2.859 80.95 72.62 3.187 2.938 80.95 74.63 3.656 3.406 92.86 86.51 4.281 4.031 108.74 102.39 C 2.625 66.68 2.625 66.68 3.093 78.56 3.760 95.90 Dimensions D E 2.510 63.75 2.510 63.75 2.953 75.01 3.596 91.34 2.380 60.45 2.380 60.45 2.848 72.34 3.472 88.19 F G H J Board Thickness Housing Part Numbers .350 8.89 .350 8.89 .375 9.53 .350 8.89 .250 6.35 .250 6.35 .155 3.94 .250 6.35 .466 11.84 .466 11.84 .406 10.31 .456 11.58 .187 4.15 .128 3.25 .156 3.96 .125 3.18 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 .055-.070 1.40-1.78 480110-2 582500-2 480133-2 480142-2 Note: Other connector sizes can be made available, consult Tyco Electronics. 169 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connectors, .156 [3.96] Centerline (Continued) Housings Preloaded with Right-Angle Post Contacts A Material and Finish: F Housing—See chart below Contacts—Phosphor bronze, plated .000015 [0.00038] min. gold in mating area, with entire contact underplated .000050 [0.00127] min. nickel Post—Phosphor bronze, tin plated Retaining Spring—Stainless steel .156 [3.96] D .125 [3.18] B C Related Product Data: H G Card Guide Assembly—page 171 Performance Specifications— page 164 Accessories—page 171 PC Board Layout—page 172 J .125 [3.18] Dia. (2 Holes) E Technical Documents: (pages 186, 187): Product Specification 108-9013 Post Contact .022 x .036 [0.56 x 0.91] Phosphor Bronze Tin Plated Phosphor Bronze Selective Gold Plate in Contact Area .000015 [0.00038] Gold .090 [2.29] Min. .156 [3.96] No. of Dual Positions 10 15 18 22 28 .325 [8.26] .150 [3.81] A B C Dimensions D E F G H J 2.407 61.14 3.182 80.82 3.650 92.71 3.657 92.89 4.274 108.56 4.281 108.74 5.270 133.86 2.157 54.79 2.933 74.5 3.400 86.36 3.457 86.54 4.025 102.24 4.031 102.39 4.961 126.01 1.886 47.9 2.621 66.57 3.088 78.44 3.136 79.65 3.754 95.35 3.760 95.50 4.680 118.87 1.722 1.598 43.74 40.59 2.506 2.376 63.65 60.35 2.948 2.843 74.88 72.21 2.972 2.848 75.49 72.34 3.591 3.466 91.21 88.04 3.596 3.472 91.34 88.19 4.527 4.402 114.99 111.81 .360 9.14 .350 8.89 .375 9.53 .350 8.89 .350 8.89 .350 8.89 .350 8.89 .700 17.78 .700 17.78 .700 17.78 .700 17.78 .700 17.78 .700 17.78 .700 17.78 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .456 11.58 .466 11.84 .406 10.31 .456 11.58 .456 11.58 .456 11.58 .456 11.58 Part Numbers Housing Material 583599-1* 583545-1* Glass-Filled Phenolic 583544-1* 530851-1* 583458-2* 583975-1* 530061-1* Glass-Filled Polyester Glass-Filled Phenolic Glass-Filled Polyester Glass-Filled Phenolic *CSA certification pending. Notes: 1. Other connector sizes can be made available, consult Tyco Electronics. 2. Finished hole size is .048-.054 [1.22-1.37] diameter. 170 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connector Accessories Keying Plugs On-Contact Keying Plug Intercontact Keying Plugs Material: Nylon Technical Documents: .040 [1.02] Wide—Part No. 582501-1 .025 [0.64] Wide—Part No. 583274-1 (pages 186, 187): Instruction Sheets 408-7036, 408-7037, 408-7068, 408-7339 .055-.070 [1.4-1.78] Board Thickness—Part No. 480143-1 Commoning Springs .055-.070 [1.4-1.78] thk. PC board—Part No. 66092-1 Material and Finish: Beryllium copper, gold plated .055-.070 [1.4-1.78] and .084-.104 [2.13-2.64] thk. PC board with locking latches— Part No. 583454-1 Technical Documents: (pages 186, 187): Instruction Sheet 408-7419 Retaining Springs Material: Stainless steel Technical Documents: (pages 186, 187): Nickel Finish—Part No. 42973-1 Plain Finish—Part No. 42973-2 Gold Finish—Part No. 42973-3 Instruction Sheets 408-7035, 408-7037 Card Guides .187 [4.75] Material: Glass-filled nylon, black .093 Dia. [2.36] .135 [3.43] Technical Documents: (pages 186, 187): Instruction Sheets 408-7557, 408-7565 .245 [6.22] .545 Ref. [13.84] .250 [6.35] .076 [1.93] 4.000 [101.6] .200 [5.08] .240 [6.1] .308 [7.82] .375 [9.52] Connector (Ref.) Card Guide Part Number 583760-1 Note: Card guides may be used with all connector housings having mounting ears. 171 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) AMP-LEAF Connector PC Board Layouts Recommended PC Board Layouts Technical Documents: (pages 186, 187): .330 [8.38] Min. Instruction Sheet 408-7037 .031 Max. [0.79] Base Line .050 Min. [1.27] B .156 [3.96] A Note: Slot for intercontact keying may be located between any two pads (except the first two and last two pads). No. of Positions Housing Material 8 P 10 P DP 15 P 18 DP DP 22 P 25 P 32 P Dimensions A B 1.396 .152 35.46 3.86 1.709 .151 43.40 3.84 2.491 .153 63.27 3.89 2.487 .152 63.17 3.86 2.940 .144 74.68 3.66 3.583 .153 91.00 3.89 3.578 .151 90.88 3.84 4.043 .150 102.69 3.81 5.117 .140 129.97 3.56 DP = Diallyl Phthalate P = Phenolic Note: Board thickness .055-.070 [1.4-1.78] all positions except 32 position–.084-.104 [2.13-2.64]. 172 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) High Current Connectors Product Facts ■ High current capability up to 30 amperes* ■ UL rated 94V-0 glass-filled thermoplastic housings ■ Choice of wire-to-board and board-to-board (solder tail) connector configurations in 3, 4, 8, 9, 10 and 12 contact sizes ■ Heavy duty contacts made of high conductivity copper alloy with tin-over-nickel plating ■ Contacts on .312 [7.92] centers ■ Large redundant areas of contact provide excellent electrical continuity ■ Connectors available for mating with .062 [1.57], .093 [2.36] and .125 [3.18] thick double-sided PC boards ■ Contacts furnished in strip form for automatic machine termination and loose form for hand tool application ■ Recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 ■ Certified by Canadian Standards Association File No. LR 7189 AMP High Current Edge Connectors are an economical answer to the costly issue of interconnecting high current printed circuitry. Designed for a current capability of up to 30 amperes*, these connectors feature UL rated 94V-0, rugged glass-filled thermoplastic housings and high conductivity copper alloy contacts with bright tin-overnickel plating. Contacts are on .312 [7.92] centers. Connectors are available in 3, 4, 8, 9, 10 and 12 contact positions and in a choice of two styles for board-toboard and wire-to-board applications. The board-to-board connectors are supplied preloaded with solder tail contacts and are designed to mate with .062 [1.57] thick doublesided daughter boards. Wire-to-board housings are available with and without mounting ears and with capabilities of mating with .062 [1.57], .093 [2.36] and .125 [3.18] thick doublesided daughter boards. These housings are designed to accept crimp, snap-in contacts which can accommodate a wire size range of 16-10 AWG [1.25-6 mm2]. Contacts are furnished in strip form for automatic machine termination and in loose form for hand tool application. While the basic contact is designed to carry 30 amperes* of current, the actual number of contacts in a connector carrying 30 amperes is limited by the “T” rise of the connector and the PC board. Performance Specifications Contact Current Rating*: 30 amperes, max. Dielectric Withstanding Voltage (Sea Level): 1800 VAC Operating Voltage: 250 VAC, max. Insulation Resistance: 1000 megohms, min. Contact Resistance @ 30 amperes: 2 milliohms, max. Operating Temperature: –40°C to +95°C Contact Engagement Force: 40 oz. [11.12 N], max. *When used with a .180 [4.57] wide double-sided PC board with 5 oz. [0.14 Kg] min. copper each side. Consult Tyco Electronics engineering when paralleling contacts for power applications. 173 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) High Current Connectors (Continued) Crimp, Snap-In Contacts Material and Finish: A—Copper alloy CDA-195 plated .000150 [0.00381] bright tin over .000030 [0.00076] nickel B—Copper alloy CDA-195 plated .000150 [0.00381] silver all over .195 [4.95] B[±.020 [±0.51] C .325 [8.26] A Related Product Data: Performance Specifications— page 173 Connector Housings—page 175 Application Tooling—pages 184, 185 .150 [3.81] .390 [9.91] Technical Documents: (pages 186, 187): Product Specification 108-9045 Application Specification 114-9005 Instruction Sheets 408-7782, 408-7783, 408-7802 Plating A A B A Wire Size Range AWG mm2 Ins. Dia. Range 0-.145 16-14 1.25-2 .20.9 29-3.68 0-.210 12-10 3-6 .41.6 06-5.33 0-.210 12-10 3-6 .41.6 06-5.33 0-.210 12-10 3-6 .41.6 06-5.33 Dimensions A B C .260 6.60 .190 4.83 .190 4.83 .190 4.83 1.160 29.46 1.230 31.24 1.230 31.24 1.230 31.24 .285 7.24 .285 7.24 .285 7.24 .347 8.81 Mateable Applicator for Hand Tool Contact Part Numbers Daughter Board AMP-O-LECTRIC 69710-1 Loose Piece Strip Form Thickness Machine Die Insert .062 530518-1 530517-2 466439-2 90333-1 1.57 .062 530520-1 530519-2 466438-2 90332-1 1.57 .062 — 530519-3 466438-2 90332-1 1.57 .093 — 531373-2 466438-2 90332-1 2.36 *Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench machines and lead-making machines. Hand Crimping Tool 69710-1 Extraction Tool 91116-1 174 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) High Current Connectors, .312 [7.92] Centerline Housings With Mounting Ears Material: White glass-filled polyester, 94V-0 rated A B .312 [7.92] Related Product Data: Performance Specifications— page 173 Contacts—page 174 * G [±.010 [±0.25] .156 Dia. [3.96] * E[±.007 [±0.18] * F[±.015 [±0.38] Technical Documents: (pages 186, 187): Product Specification 108-9045 Instruction Sheet 408-9123 X, Y PC Board Thickness C .750±.010 [19.05±0.25] 1.400±.010 [35.56±0.25] .300 [7.62] Void Coring Optional * D[±.010 [±0.25] No. of Pos. 3 4 8 9 12 A B 1.024 26.01 1.336 33.93 2.584 65.63 2.896 73.56 3.832 97.33 .624 15.85 .936 23.77 2.184 55.47 2.496 63.40 3.432 87.17 Dimensions C D 1.164 29.57 1.476 37.49 2.724 69.19 3.036 77.11 3.972 10.89 1.114 28.3 1.426 36.22 2.674 67.92 2.986 75.84 3.922 99.62 .400 [10.16] Board Slot Depth E F G 1.538 39.07 1.850 46.99 3.098 78.69 3.410 86.61 4.346 110.39 1.972 50.09 2.284 58.01 3.532 89.71 3.844 97.64 4.780 121.41 .500 12.70 .437 11.10 .437 11.10 .437 11.10 .437 11.10 Housing Part Numbers X = .062 [1.57] Y = .093 [2.36] With With Mtg. Ears Mtg. Ears — 531370-2 530521-3 — 530521-6 — 530521-7 — 530521-9 — Notes: 1. X Housings designed to accept .055-.070 [1.4-1.78] thick daughter boards; use intercontact Keying Plug No. 530533-1. Notes: 2. Y Housings designed to accept .084-.102 [2.13-2.59] thick daughter boards; use intercontact Keying Plug No. 531369-1. + Contact 531373-2. Notes: 3. Use Extraction Tool No. 91116-1 to remove contacts. (Refer to Instruction Sheet 408-7782). 4. Other connector sizes can be made available, consult Tyco Electronics. 175 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) High Current Connectors .312 [7.92] Centerline (Continued) Housings Preloaded with Solder Tail Contacts B[±.007 [±0.18] .312 [7.92] .437±.010* [11.1±0.25] Material and Finish: Housing—White glass-filled polyester, 94V-0 rated Contacts— A—Copper alloy CDA-195 plated .000150 [0.00381] bright tin over .000030 [0.00076] nickel B—Copper alloy CDA-195 plated .000150 [0.00381] silver plate over .000030 [0.00076] thk. nickel C—Copper alloy CDA-195 plated .000030 [0.00076] gold in contact area, .000150 [0.00381] tin-lead solder post, over .000030 [0.00076] nickel E .156 Dia. [3.96] .218 [5.54] D Fit for .062 [1.57] PC Board C[±.010 [±0.25] .937 .300 [23.8] [7.62] .400 [10.16] Board Slot Depth .030 [0.76] F Related Product Data: Performance Specifications— page 173 A[±.015 [±0.38] Technical Documents: (pages 186, 187): Product Specification 108-9045 Void Coring Optional .130±.003 Dia. [3.3±0.08] .375 [9.52] .104±.002 Dia. [2.64±0.05] .539 [13.69] E B PC Board Thickness: .062 [1.57] Recommended PC Board Hole Layout *May go to .020 [0.51] over nominal at top center of housing. No. of Positions 3 4 5 6 A 1.972 50.09 2.284 58.01 2.593 65.86 2.908 73.86 B 1.538 39.07 1.850 46.99 2.162 54.91 2.474 62.84 Dimensions C 1.164 29.57 1.476 37.49 1.788 45.42 2.100 53.35 D 1.024 26.01 1.336 33.93 1.648 41.86 1.960 49.78 E .624 15.85 .936 23.77 1.248 31.70 1.560 39.62 8 3.532 89.71 3.098 78.69 2.724 69.19 2.584 66.63 2.184 55.47 9 3.844 97.64 3.410 86.61 3.036 77.11 2.896 73.56 2.496 63.40 10 4.156 105.56 3.722 94.54 3.348 85.04 3.208 81.48 2.808 71.32 12 4.780 121.41 4.346 110.39 3.972 100.89 3.832 97.33 3.432 87.17 Plating Connector Part Numbers A 531353-2 A 531353-3 A 531353-4 A 531353-5 .180 4.57 A B 531353-6 145116-3 .283 7.19 .180 4.57 B 146912-2 A 531353-7 .180 4.57 A B 531353-8 145116-1 .283 7.19 B 146912-3 .180 4.57 A B C 531353-9 145116-2 645200-3 .283 7.19 B 146912-1 F .180 4.57 .180 4.57 .180 4.57 .180 4.57 Notes: 1. A .062 [1.57] thick dummy PC board should be inserted into the connector during soldering to a mother board. 2. Other connector sizes can be made available, consult Tyco Electronics. 176 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) DUO-TYNE Flag Connectors Product Facts ■ Right angle design permits cabling in close quarters ■ Recessed contacts help prevent arcing ■ Sizes and configurations available with or without mounting ears ■ Lowest installed costs achieved through highspeed compression crimping with AMP matched tooling ■ Meets quality and reliability requirements for appliance controls, vending machine subassemblies and business machines ■ Recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 ■ Certified by Canadian Standards Association File No. LR 7189 This flag-type connector is designed to meet the quality and reliability of such equipment as appliance controls, vending machine subassemblies, television, stereo, business machines and other applications with similar control needs. Among its assembly-saving features is a right-angle design which permits cabling in close quarters, where it does not require frame mounting to attach the keyed housing to the card cutout and double locking of the contacts when a PC board is inserted. In addition, contacts are recessed to prevent arcing. All sizes and configurations are available with or without mounting ears. Added to low initial cost, lowest installed costs are achieved through highspeed compression crimping with Tyco Electronics matched tooling. Performance Specifications Contact Rating*: 5 amperes High Potential: 2200 VAC, rms Operating Temperature: –40°C to +105°C Vibration: 10 to 55 cps per MIL-STD-1344, Method 202 *Consult Tyco Electronics engineering when paralleling contacts for power applications. 177 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) DUO-TYNE Flag Connectors (Continued) Tapered Beam Crimp, Snap-In Contacts Material and Finish: Beryllium copper or phosphor bronze (see chart) plated as follows: Plating A—.000030 [0.00076] gold in mating area, with entire contact underplated .000050 [0.00127] nickel Plating B—.000015 [0.00127] gold in mating area, with entire contact underplated .000050 [0.00127] nickel Plating C—.000150 [0.00381] tin Related Product Data: Performance Specifications— page 177 Connector Housings—page 179 Application Tooling—pages 184, 185 Technical Documents: Wire Size Range AWG mm2 26-22 0.12-0.4 Insulation Dia. Range Material .035-.055 0.89-1.40 Beryllium Copper (pages 186, 187): Product Specification 108-9038 Application Specification 114-9002 Instruction Sheets 408-7047, 408-7780, 408-7848, 408-7849 Phosphor Bronze 22-18 0.3-0.9 .060-.090 1.52-2.29 Beryllium Copper Contact Contact Part Numbers Finish Strip Form (Plating) Loose Piece A B B C A C A B C 530005-3 — — — — — — 530007-3 — 530004-6 530004-7 530002-7 530002-5 530002-3 530006-5 530006-6 — 530006-2 Applicator for AMP-O-LECTRIC Hand Tool Machine* 466586-2 90094-4 466424-2 90027-4 .090-.130 Phosphor C — 530505-5 466413-2 — 2.29-3.30 Bronze *Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench machines and lead-making machines. 18-16 0.8-1.4 Hand Crimping Tool Contact Extraction Tool 810992-1 178 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) DUO-TYNE Flag Connectors (Continued) Housings, With and Without Mounting Ears A .100 [2.54] Material: Natural nylon Related Product Data: Performance Specifications— page 177 Contacts—page 178 PC Board Layout—page 181 .265 [6.73] Technical Documents: .090 [2.29] (pages 186, 187): .060 [1.52] B .156 [3.96] Dia. 2 Holes .500 [12.70] .375 [9.53] .095 [2.41] Product Specification 108-9038 Application Specification 114-9002 Instruction Sheet 408-7047 .590 [14.99] On-Contact Keying Plug Fit for .055-.070 [1.40-1.78] PCBoard .295 [7.49] .156 [3.96] .380 [9.65] Material: Nylon C .190 [4.83] D Part Number 583661-1 Technical Documents: (pages 186, 187): Instruction Sheet 408-7486 Part Numbers With Mounting Ears Without Mounting Ears For Ins. For Ins. For Ins. For Ins. Dia. Range Dia. Range Dia. Range Dia. Range .035-.090 .090-.130 .035-.090 .090-.130 [0.89-2.29] [2.29-3.30] [0.89-2.29] [2.29-3.30] No. of Pos. A 3 1.384 35.15 .414 10.52 .624 15.85 1.004 25.50 582380-9 — — — 5 — .736 22.40 .936 27.74 — — — 582370-9 530853-2 6 1.852 47.04 .882 22.40 1.092 27.74 1.472 37.39 582382-9 530509-1 582371-9 530853-3 9 2.320 58.93 1.350 34.29 1.560 39.62 1.940 49.28 582383-9 530509-2 582375-9 — 12 2.788 70.82 1.818 46.18 2.028 51.51 2.408 61.16 582384-9 530509-6 582376-9 530853-5 14 3.100 78.74 2.130 54.10 2.340 59.44 2.720 69.09 582385-9 530509-7 582372-9 530853-6 15 3.256 82.70 2.286 58.06 2.496 63.40 2.876 73.05 582386-9 530509-3 582377-9 — 18 3.724 94.59 2.754 69.95 2.964 75.29 3.344 84.94 582387-9 530509-8 582378-9 530853-8 22 4.348 110.44 3.378 85.80 3.588 91.14 3.968 100.79 582388-9 530509-9 582379-9 — Dimensions B C D Note: Other connector sizes can be made available, consult Tyco Electronics. 179 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) DUO-TYNE Flag Connectors (Continued) Recommended PC Board Layouts Related PC Board Data: Recommended Board Thickness— .055-.070 [1.40-1.78] Recommended Chamfer of Mating Edge of Boards—.015 [0.38] x 45° Recommended Pad Plating—Tin .000150-.000400 [0.00381-0.01016] thick .014/.016 [0.36/0.41] ±.003 A [±0.08] .044 ±.005 [1.12 ±0.13] .062 ±.005 [1.57 ±0.13] .156 ±.005 [3.96 ±0.13] .280 ±.008 [7.11 ±0.13] Contact Pads .148 [3.76] R. Retaining Dimples (Optional) Contact Pads ±.003 A [±0.08] .115 Min. [2.92] No. of Positions 3 5 6 9 12 14 15 18 22 .070 ±.005 [1.78 ±0.13] Dimension A .400 10.16 .712 18.09 .868 22.05 1.337 33.96 1.805 45.85 2.117 53.77 2.272 57.71 2.741 69.62 3.365 85.47 180 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Printed Circuit Board Connector Hood Assemblies Product Facts ■ Can be used with the highly versatile AMP-LEAF and Crimp Snap Twin Leaf printed circuit edge connectors ■ Clamping capabilities for wire bundles to .550 [13.97] maximum diameter ■ Available with 90° or 180° cable outlet ■ All plastic construction— thermoplastic material UL rated 94V-0 for electrical and mechanical applications up to + 105°C ■ Thermoplastic material has excellent resistance to common commercial cleaners when used at moderate temperatures ■ Separate hood assembly halves permit easy cable dressing ■ Furnished in convenient kit form—each kit includes four cable clamp sizes For use with the following connectors: Crimp Snap Twin Leaf Connectors (Pages 154-163) AMP-LEAF Connectors (Pages 164-172) 181 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Specific Product Name_12 Hel. Con. (Continued)_9pt Helvetica Lt Condensed 90° Cable Outlet Material: Natural color thermoplastic .240 [6.10] Related Product Data: Crimp Snap Twin Leaf Connectors—pages 154-163 AMP-LEAF Connectors— pages 164-172 .260 [6.60] .350 [8.89] .440 [11.18] #5 x 3/8 [9.52] Thread Forming Screw (3) 1.500 [38.10] 1.150 [29.21] Technical Documents: (pages 186, 187): Instruction Sheet 408-7719 .170 [4.32] .625 [15.88] 1.797 [45.64] #5 x 5/8 [15.88] Thread Forming Screw (2) Connector Size No. of Contact Mtg. Hole Length Pos. Centers Centers (Max.) 18 22 1.56 3.96 .156 3.96 3.406 86.51 4.031 102.39 3.685 93.60 4.296 109.12 .375 [9.52] Hood Connector Width .380 [9.65] Max. Connector Width .437[11.10] AMP Hood AMP Hood L Dim. Connector Assembly Connector Assembly (Max.) Family Kit Number* Family Kit Number* 3.826 AMP-LEAF 530088-3 — — 97.18 4.451 Crimp Snap — — 1-530088-4 113.06 Twin Leaf *All screws and four sizes of cable clamps are supplied with each kit. Note: Other hood sizes can be made available, consult Tyco Electronics. 182 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors (Board-to-Board, Wire-to-Board) Printed Circuit Board Connector Hood Assemblies (Continued) 180° Cable Outlet .440 [11.18] .350 [8.89] Material: Natural color thermoplastic .625 [15.88] .260 [6.60] Related Product Data: AMP-LEAF Connectors— pages 164-172 1.500 [38.10] .170 [4.32] Technical Documents: (pages 186, 187): 1.875 [47.62] .240 [6.10] Instruction Sheet 408-7719 1.150 [29.21] #5 x 5/8 [15.88] Thread Forming Screw (2) No. of Pos. 22 Contact Centers .156 3.96 #5 x 3/8 [9.52] Thread Forming Screw (2) .563 [14.30] Connector Size Mtg. Hole Centers 4.031 102.39 Length (Max.) 4.321 109.76 Hood L Dim. (Max.) 4.451 113.06 Connector Width .380 [9.65] Max. AMP Connector Hood Assembly Family Kit Number* AMP-LEAF 530087-4 *All screws and four sizes of cable clamps are supplied with each kit. Note: Other hood sizes can be made available, consult Tyco Electronics. 183 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Application Tooling for Wire Crimp Contacts Tooling shown on this page is designed to terminate wire crimp contacts used in various wire-to-board connectors. AMP-O-LECTRIC Model “G” Terminating Machine (Shown with Optional Crimp Quality Monitor) The AMP-O-LECTRIC Model “G” is a semi-automatic bench-top machine for terminating wire using reeled terminals and contacts. It features a quiet and reliable direct motor drive, microprocessor controls for ease of setup and operation, and guarding and lighting designed for operator convenience and safety. Three versions are available: with AMP-O-MATIC Model II Stripper/Crimper Machine (Shown with Optional Crimp Quality Monitor) This machine also strips wire, and is therefore used to terminate jacketed cable. It features manual precision adjust, keyed strip blades for faster, more accurate setups, and an efficient scrap removal system. Applicators are interchangeable. All adjustments can be made from the front of the machine without special tools. Entry Level Terminator (ELT), 1338600-(x) Semiautomatic Bench Terminator for side- and end-feed reeled terminals and contacts. The ELT uses a DC motor with gear box drive. The result is a smallfootprint design that is fast and quiet. Cycle time is less than 0.400 sec. with an operation sound level of 76dBa. With a crimp force capacity of 3,000 pounds, the ELT is available for all Optional Stripping Module for the ELT and AMP-O-LECTRIC Model G The combination of the Stripping Module with the AMP-O-LECTRIC Model G Terminator or the Entry Level Terminator provides an economical, proficient method of stripping wire and crimping terminals on the same machine. Wires are stripped moments before crimping, meaning there is virtually no chance automatic precision adjust and machine-mounted sensors, or with manual precision adjust with or without sensors. All versions will accept existing Tyco Electronics ministyle applicators with minor modifications. For further details, request Tyco Electronics Catalog 65828. but the highest crimp force applications. Optional equipment is also available to meet your specific application requirements. For more information, request catalog 1308382. of damaging wire conductors during handling or storage. Once the wire is fed into the start sensor the Stripping Module does the rest, improving placement accuracy. For more information, request catalog 1309085. 184 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Application Tooling for Wire Crimp Contacts (Continued) AMPOMATOR CLS IV+ Lead-Making Machines, 356500-1, -2 Fully-automatic machines that measure, cut, strip and terminate single leads. Microprocessor-controlled, and programmed and operated using an easy-to-follow, menu-driven touchscreen. Features include direct-drive terminating units with precision crimp height adjustment, fully programmable setups, Crimp Quality Monitor (CQM), 1320420-1, -2 This unique system provides 100% on-the-fly crimp inspection. It measures the crimp height of each termination, and evaluates the quality of each crimp. If a crimp is questionable, the monitor alerts the operator with both visual and audible alarms. It also provides ports for printing and networking. When used with wire runout and splice detection, and motorized pre-feed with wire straightener. Crimp quality monitoring is also available. For more information, request catalog 124324. AMP-O-LECTRIC Model “G” Termination Machines, the monitor is mounted to the machine. When used with AMPOMATOR CLS IV LeadMaking Machines, it is integrated into the machine’s operating system. For more information, request catalog 82275. CERTI-CRIMP Straight Action Hand Tools (SAHT) Premium grade hand tools. Feature ratchet control to provide complete crimp cycle. Die sets close in a straight line. Include a contact locator and wire stop, plus an insulation crimp adjustment lever, when applicable. Approximate weight 1.3 lb [0.59 kg]. For more information, request catalog 65780. Lightweight, air-operated modular tooling system. Accepts a wide variety of interchangeable heads for crimping various types of contacts, terminals and splices onto wires ranging 6-26 AWG [13-0.12 mm2], plus coaxial and fiber optic cable. Available with either hand- or foot-actuation switch. Optional ratchet control available to provide complete crimp cycle. 626 Pneumatic Tool System For more information, request catalog 124208. 185 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Technical Documents 114-26003 Linear ZIF PC Board Edge Connector, .100 [2.54] Centerline The following is a list of technical documents covering the application, performance and maintenance of the AMP Card Edge Connectors presented in this catalog. Instruction Sheets: 408-2665 Linear ZIF, Carrier Removal Tool Series 265924 408-2995 Linear ZIF, Housing Wing Removal and Replacement Tool 266233-1 408-2999 Linear ZIF, T-Bar Insertion Tool Series 266267 408-6915 Linear ZIF, Housing Assembly Insertion Tool Series 313136 408-6916 Linear ZIF, T-Bar Insertion Tool Series 313139 Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineer. Application Specifications describe requirements for using the product in its intended application and/or crimping information. They are intended for the Packaging and Design Engineer and the Setup person. Instruction Sheets provide instructions for assembling or applying the product. They are intended for the Manufacturing Assembler or Operator. Press-Fit Board-to-Board Connectors AMP PACE Connectors Solder Type Board-to-Board Connectors Product Specifications: 108-14019 AMP PACE Connector, .125 x .250 [3.18 x 6.35] Centerline 108-26003 ACTION PIN Contacts Standard Edge .050 Series PCI Connectors Product Specification: 108-14034 Standard Edge .050 Series PCI Connector Application Specification: 114-26002 AMP PACE Connector Application Specification: 114-26012 Standard Edge .050 Series PCI Connector Instruction Sheets: 408-2933 Contact Replacement Tool .100 x .200 [2.54 x 5.08] and .125 x .250 [3.18 x 6.35], AMP PACE Connector 408-2978 Seating Tool Ground Module, AMP PACE Connector 408-2979 Seating Tool Power Module, AMP PACE Connector 408-6726 Seating Tool, .156 x .200 [3.96 x 5.08] Part No. 59955, AMP PACE Connector 408-6727 Seating Tool, .125 x .125 [3.18 x 3.18] Part No. 59953, AMP PACE Connector 408-6881 Contact Replacement Tool .100 x .100 [2.54 x 2.54] with and without Scoops AMP PACE Connector 408-9058 Seating Tool .100 x .200 [2.54 x 5.08] with Card Scoops, Part No. 58150, AMP PACE Connector 408-9063 Seating Tool .125 x .250 [3.18 x 6.35] Part No. 58142, AMP PACE Connector 408-9067 Seating Tool .100 x .200 [2.54 x 5.08] Part No. 58140, AMP PACE Connector 408-9091 Accessories and Tooling, .100 x .200 [2.54 x 5.08] AMP PACE Connector 408-9119 Seating Tool, .125 x .250 [3.18 x 6.35] with Card Scoops, Part No. 58184, AMP PACE Connector 408-9186 Contact Replacement Tool; .100 x .200 [2.54 x 5.08], .125 x .125 [3.18 x 3.18], .125 x .250 [3.18 x 6.35] with Scoops, .156 x .200 [3.96 x 5.08], AMP PACE Connector 408-9188 Seating Tool .100 x .100 [2.54 x 2.54] Part No. 58200, AMP PACE Connector Standard Edge .050 Series Connectors Product Specification: 108-14034 Standard Edge .050 Series Connector Application Specification: 114-26012 Standard Edge .050 Series Connector Standard Edge II Connectors Product Specification: 108-9039 Standard Edge II Connector Low Profile Connectors Product Specification: 108-9044 Low Profile Edge Connector Instruction Sheet: 408-7772 Contact Replacement, Low Profile Edge Connector Twin Leaf Mother Board Connectors Product Specification: 108-9027 Twin Leaf Mother Board Connector Instruction Sheets: 408-7479 Keying Plugs, Twin Leaf Mother Board Connector 408-7498 Connector Layout, Twin Leaf Mother Board Connector 408-7506 Card Guides, Twin Leaf Mother Board Connector Rotary Cam ZIF Connectors Product Specification: 108-9048 Rotary Cam PC Board Edge Connector Instruction Sheet: 408-7911 Rotary Cam ZIF Connectors Linear ZIF Connectors Product Specifications: 108-14015 Linear ZIF PC Board Edge Connector, .100 [2.54] Centerline 108-26003 ACTION PIN Contacts ECONOMATE Connectors Application Specification: Product Specification: 108-26002 ECONOMATE Connector Instruction Sheet: 408-9091 Accessories and Tooling, .100 x .200 [2.54 x 5.08] AMP PACE Connector 186 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Technical Documents (Continued) Wire-to-Board Connectors High Current Connectors Crimp Snap Twin Leaf Connectors Product Specification: 108-9045 High Current Edge Connector Product Specification: 108-9031 Crimp Snap Twin Leaf Connector (Bifurcated Contacts) Application Specification: 114-9005 Contact, High Current Edge Connector Instruction Sheets: 408-7782 Extraction Tool 91116-1, High Current Connector 408-7783 Die Inserts 90332-1 and 90332-2 408-7802 Die Inserts 90333-1 and 90333-2 408-9123 High Current Connectors Application Specification: 114-9004 Contact, Twin Leaf Connector Instruction Sheets: 408-7527 Accessories and Contacts, Crimp Snap Twin Leaf Connector 408-7529 Extraction Tool 91073-1 408-7531 Hand Tool 90268-1, Single Crimp, 28-24 AWG [0.08-0.2 mm2] Wire 408-7551 Hand Tool 90264-1, Double Crimp, 22-20 AWG [0.3-0.6 mm2] and 18 AWG [0.8-0.9 mm2] Wire 408-7583 Hand Tool 90285-1, Double Crimp, 20-18 AWG [0.5-0.9 mm2] and 16 AWG [1.25-1.4 mm2] Wire 408-8547 CERTI-CRIMP II Straight Action Hand Tools DUO-TYNE Flag Connectors Product Specification: 108-9038 DUO-TYNE Flag Connector, Tapered Beam Contact Application Specification: 114-9002 Contact, DUO-TYNE Flag Connector Instruction Sheets: 408-7047 DUO-TYNE Flag Right-Angle Connector 408-7486 On-Contact Keying Plug 583661 408-7780 Hand Tool 90335-1, 18-16 AWG [0.8-1.4 mm2] Wire 408-7848 Hand Tool 90027-4, 22-18 AWG [0.3-0.9 mm2] Wire 408-7849 Hand Tool 90094-4, 26-22 AWG [0.12-0.4 mm2] Wire AMP-LEAF Connectors Product Specifications: 108-9013 AMP-LEAF Connector 108-9043 AMP-LEAF Connector, Tin Plated Contacts Application Specification: 114-9003 Contact, AMP-LEAF Connector Instruction Sheets: 408-6951 Lubricant for tin plating, fretting, corrosion 408-7035 Retaining Spring 42973 408-7036 On-Contact Keying Plugs 480143 and 582756 408-7037 Accessories and Contacts, AMP-LEAF Connector 408-7045 Extraction Tool 465195 408-7068 Intercontact Keying Plug 582501 408-7339 Intercontact Keying Plug 583274 408-7419 Commoning Springs 408-7622 Hand Tool 90017-3, 22-20 AWG [0.3-0.6 mm2], Two 22 AWG [0.3-0.4 mm2] or One 18 AWG [0.8-0.9 mm2] Wire 408-7623 Hand Tool 90028-3, 26-22 AWG [0.12-0.4 mm2], Two 22 AWG [0.3-0.4 mm2] Wires 408-7624 Hand Tool 90031-8, Two 18 AWG [0.8-0.9 mm2] Wires 408-7626 Hand Tool 90101-3, 20 AWG [0.5-0.6 mm2] or Two 20 AWG [0.5-0.6 mm2] Wires Printed Circuit Board Connector Hood Assemblies Instruction Sheet: 408-7719 Printed Circuit Board Connector Hood Assemblies 187 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Tyco Part Number to Acquired Part Number All Tyco Electronic Part Numbers without a corresponding acquired Part Number are listed as base part numbers only. Complete part numbers (with prefixes and/or suffixes) are shown on the page(s) indicated. Contact Engineering if no corresponding Tyco Number is available. Tyco Part Number Acquired Part Number 11299 42973 58084 58140 58142 58143 58150 58184 58200 58210 58218 59881 60151 66067 66084 66092 69710 90017 90027 90028 90031 90094 90101 90264 90268 90285 90332 90333 91081 91088 91116 91535 98014 98341 117169 117249 117269 117272 117285 117296 117311 117793 117795 117796 117798 117879 117880 118243 118778 118951 118982 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 119136 119163 119196 119200 119202 119216 119216 119237 119254 119256 119311 119341 119413 119552 119677 — — — — — — — — — — — — — — — Page Number 9 171 117 115 115 115 115 115 115 115 115 112 165 166 165 171 174 165 174 165 165 174 165 155 155 155 174 174 72 72 174,175 155 57 150 112,122 124,126 124,126 126 121,126 121,126 123 126 120,126 126 120,126 126 126 123 121 120 100,102, 104,105, 106,108, 110,111, 120,121 123 103 88 107 107 103 103 101 110 110 88 112 101 105 103 Tyco Part Number Acquired Part Number 119726 119734 119736 119738 119790 119791 119802 — — — — — — — 119822 119831 119840 119841 119853 119880 119950 145031 145089 145098 145113 145116 145154 145165 145166 145167 145168 145169 145246 146912 147400 147668 176137 176139 265868 265871 — — — — — — — — — — — — — — — — — — — — — — — — — — 265879 265881 265902 265904 265905 265906 265910 265911 265912 265924 265931 265937 265962 266129 266220 266233 266235 266264 266267 313136 313139 313256 343371 350396 356500 465195 466366 466367 466368 466413 466424 466438 466439 466577 466586 466622 466713 466912 466919 466928 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Page Number 103 101 101 103 110 103 100,102, 104,106, 108,110, 111,120 107 101 107 107 104 105 93 14 23 9 8 176 9 10 8 9 10 8 10 176 85 129 17 25 126 95,115, 126 126 126 126 126 126 126 126 126 126 95,126 126 126 126 126 115 95,186 95 95 95 95 95 95 165 21 185 165 165 165 165 178 178 174 174 155 178 155 155 155 155 155 Tyco Part Number Acquired Part Number 480110 — 480133 — 480142 — 480143 530002 530004 530005 530006 530007 530030 530061 530087 530088 530213 530218 530238 530245 530265 530267 530268 530270 530278 530282 530286 530290 530291 530292 530384 530396 530505 530509 530517 530518 530519 530520 530521 530533 530654 530655 530656 530657 530659 530662 530663 530664 530666 530667 530668 530669 530671 530672 530673 530674 530677 530678 530689 530825 530826 530841 530842 530843 530844 530851 530853 531004 531007 531019 531020 531021 531023 531024 531025 531026 531250 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Page Number 165,168, 169 165,168, 169 165,168, 169 171 178 178 178 178 178 72 170 183 182 162 158 160 156 72 72 72 72 72 72 72 72 72 66 22 21 178 179 174 174 174 174 175 175 62 62 62 62 60 60 60 60 62 62 62 62 60 60 60 60 62 62 62 21 22 20 20 17 18 170 179 80 78 74 74 74 77 77 78 78 22,162 188 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Tyco Part Number to Acquired Part Number Tyco Part Number Acquired Part Number 531341 531353 531369 531370 531373 531395 531395 531396 531414 531433 531476 531477 531478 531534 531863 532563 532600 536128 582140 582147 582264 582355 582370 582371 582372 582375 582376 582377 582378 582379 582380 582382 582383 582384 582385 582386 582387 582388 582500 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 582501 582963 583167 583204 583274 583280 583294 583361 583407 583425 583454 583458 583485 583486 583533 583544 583545 583552 583555 583599 583616 583617 583649 583660 583661 583671 583679 583680 583685 583691 583692 583694 583714 583715 583717 583718 583722 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Page Number 20 176 175 175 174,175 75 75 75 76 62 155 155 155 66 79 79 23 25 165,168 165,168 165,168 166 179 179 179 179 179 179 179 179 179 179 179 179 179 179 179 179 165,168, 169 171 165,168 165,168 165 162,171 165,168 166 165 66,72 71 171 170 66,72 66,72 66,72 170 170 167 165 170 155 165,167 155 68,72 179 70 68,72 165,167 165,167 162 68,72 66 72 68,72 157 157 165,167 Tyco Part Number Acquired Part Number 583723 583724 583725 583726 583752 583753 583754 583755 583760 583764 583853 583854 583857 583859 583861 583864 583873 583875 583879 583884 583900 583975 583989 583990 583991 645115 645116 645135 645142 645145 645146 645147 645149 645155 645169 645200 645235 645293 645384 645394 650025 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 650059 650083 650090 650091 650092 650118 650122 650123 650124 650148 650149 650150 650181 650187 650207 650263 650281 650297 650616 650718 650719 650728 678034 678035 687775 810992 1320420 1338600 1437266 1490560 1490563 1571235 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Page Number 165,167 165,167 165,167 165,167 72 72 72 72 171 162 155 156 162 161 157 159 159 155 156 156 158 170 165 165 165 87 91 84 92 85 89 86 90 66 25 176 24 80,82 23 105 17,18, 20,21, 22,23, 24,25, 63 109 79 12 13 12 23 103 103 103 117 117 117 12 23 18 17 117 103 25 20 14 19 107 111 155 178 185 184 151 150 150 109 Tyco Part Number 0-1437261-2 0-1437261-5 0-1437261-6 0-1437262-4 0-1437262-5 0-1437262-6 0-1437262-7 0-1437262-9 0-1437263-7 0-1437263-8 0-1437264-3 0-1437264-6 0-1437264-7 0-1437264-9 0-1437267-5 0-1437267-6 0-1437267-7 0-1437267-8 0-1437267-9 0-1437268-4 0-1437268-5 0-1437268-6 0-1437268-7 0-1437268-8 0-1437268-9 0-1437270-1 0-1437270-2 0-1437270-3 0-1437270-4 0-1437270-6 0-1437270-7 0-1437270-8 0-1437270-9 0-1437274-3 0-1437274-5 0-1437274-7 0-1437274-8 0-1437274-9 0-1437276-2 0-1437276-3 0-1437276-5 0-1437276-6 0-1437276-8 0-1437276-9 1-1437260-4 1-1437260-5 1-1437261-1 1-1437262-0 1-1437262-3 1-1437262-4 1-1437262-8 1-1437262-9 1-1437263-4 1-1437263-5 1-1437263-6 1-1437263-7 1-1437263-8 1-1437263-9 1-1437264-0 1-1437264-5 1-1437264-6 1-1437265-0 1-1437265-2 1-1437265-3 1-1437265-4 1-1437265-5 1-1437265-6 1-1437265-7 1-1437266-0 1-1437266-1 1-1437266-6 1-1437266-8 1-1437267-0 1-1437267-1 1-1437267-2 1-1437267-3 1-1437267-4 Acquired Part Number C8D50PF29023 C8D50PF29033 C8D50PF29043 C6D06PF29013 C6D06PF29043 C6D10PF29022 C6D10PF29043 C6D15PF29022 C7D06PF29023 C7D06PF29043 C1D18PF29015 C1D20PF29015 C1D20PF29043 C1D25PF29013 A6D06DS29A3 A6D10DS29A2 A6D10DS29C2 A6D10DS29C3 A6D10RA29A A7D06DS29C2 A7D06RA29C A7D06RA29E A7D10DS29C2 A7D10RA29AM231 A7D10WW29A3 A8D31DS29B3 A8D31DS29C2 A8D31DS29D2 A8D31RA29A A8D31RA29C A8D31RA29CM233 A8D31RA29E A8D31RA29F C7D06DS29C1 C7D15DS29C1 C7D15DS29C3 C7D18DS29C3 C7D22DS29C1 C8D31DS29A3 C8D31DS29C1 C8D31DS29C2 C8D31DS29C3 C8D31DS29D1 C8D31DS29D3 C8D06PF29013 C8D06PF29043 C8D60PF29023 C6D15PF29023 C6D18PF29013 C6D18PF29023 C6D22PF29013 C6D22PF29023 C7D18PF29012 C7D18PF29013 C7D18PF29022 C7D18PF29023 C7D18PF29043 C7D20PF29012 C1D25PF29015 C1D35PF29013 C1D35PF29015 W8D18PF29063 W8D22PF29043 W8D25PF29013 W8D25PF29063 W8D25PF29093 W8D28PF29013 W8D28PF29093 98230 98231 98236 98238 A6D10RA29AM233 A6D10RA29C A6D10RA29E A6D10WW29A3 A6D12DS29C2 Page Number 138 138 140 148 148 146 148 146 142 144 131 131 131 131 54 54 54 54 56 49 52 52 49 51 49 43 43 43 46 46 47 46 46 36 36 36 36 36 32 31 31 32 31 32 140 140 138 146 148 146 148 146 144 144 142 142 144 144 131 131 131 136 134 134 136 136 134 136 150 150 150 150 56 56 56 54 54 189 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Tyco Part Number to Acquired Part Number Tyco Part Number 1-1437267-5 1-1437267-6 1-1437267-7 1-1437267-9 1-1437268-1 1-1437268-2 1-1437268-3 1-1437268-4 1-1437268-5 1-1437268-6 1-1437268-7 1-1437268-8 1-1437268-9 1-1437269-9 1-1437270-0 1-1437270-2 1-1437270-3 1-1437270-4 1-1437270-5 1-1437270-6 1-1437270-7 1-1437270-8 1-1437270-9 1-1437273-3 1-1437273-4 1-1437273-5 1-1437273-6 1-1437273-7 1-1437273-8 1-1437273-9 1-1437274-0 1-1437274-1 1-1437274-3 1-1437274-4 1-1437274-6 1-1437274-7 1-1437274-8 1-1437274-9 1-1437276-0 1-1437276-1 1-1437276-3 1-1437276-4 1-1437276-5 1-1437276-6 1-1437276-8 1-1437276-9 1437260-4 1437260-5 1437260-6 1437260-7 1437266-3 1437266-4 1437266-5 1437266-6 1437266-7 1437266-8 1437266-9 1437274-1 2-1437260-0 2-1437260-2 2-1437260-3 2-1437260-4 2-1437260-5 2-1437260-6 2-1437260-7 2-1437260-9 2-1437262-0 2-1437262-4 2-1437262-6 2-1437262-7 2-1437262-8 2-1437262-9 2-1437263-0 2-1437263-1 2-1437263-3 2-1437263-4 2-1437263-7 Acquired Part Number A6D12RA29A A6D12WW29A3 A6D15DS29A2 A6D15DS29C2 A7D15DS29A2 A7D15DS29C2 A7D15RA29C A7D15RA29E A7D15WW29A3 A7D18DS29A2 A7D18DS29B2 A7D18WW29A3 A7D22DS29C2 A8D10DS29A2 A8D31WW29A3 A8D35DS29A2 A8D35DS29C2 A8D35RA29C A8D35WW29A3 A8D36DS29A2 A8D36DS29B3 A8D36DS29C2 A8D36DS29C3 C6D06DS29A1 C6D06DS29C1 C6D06DS29C3 C6D06DS29D1 C6D06DS29D3 C6D06DS29D4 C6D10DS29A1 C7D22DS29D3 C7D25DS29C1 C7D28DS29A1 C7D28DS29A3 C7D28DS29B3 C7D28DS29C1 C7D28DS29C3 C7D28DS29D1 C8D35DS29A1 C8D35DS29A3 C8D35DS29C3 C8D35DS29E3 C8D36DS29A3 C8D36DS29C1 C8D36DS29C2 C8D36DS29C3 9820302 9820305 9836301 9836702 9818002 9818004 9818005 9820301 9820401 98206 98224 98293 C8D10PF29013 C8D10PF29023 C8D10PF29043 C8D12PF29013 C8D12PF29023 C8D12PF29043 C8D15PF29013 C8D15PF29023 C6D22PF29043 C6D28PF29013 C6D28PF29023 C6D28PF29033 C6D28PF29043 C6D30PF29023 C7D20PF29013 C7D20PF29023 C7D22PF29013 C7D22PF29023 C7D28PF29012 Tyco Part Number Page Number 54 54 54 54 49 49 52 52 49 49 49 49 49 43 44 43 43 46 44 43 43 43 43 39 39 39 39 39 40 39 36 36 36 36 36 36 36 36 31 32 32 32 32 31 31 32 151 151 151 151 151 151 151 151 151 150 150 150 140 138 140 140 138 140 140 138 148 148 146 146 148 146 144 142 144 142 144 2-1437263-8 2-1437263-9 2-1437264-2 2-1437264-3 2-1437264-4 2-1437265-0 2-1437265-1 2-1437265-3 2-1437265-5 2-1437265-6 2-1437265-7 2-1437265-8 2-1437267-0 2-1437267-1 2-1437267-2 2-1437267-3 2-1437267-4 2-1437267-5 2-1437267-7 2-1437267-8 2-1437267-9 2-1437268-1 2-1437268-2 2-1437268-3 2-1437268-4 2-1437268-5 2-1437268-8 2-1437268-9 2-1437269-0 2-1437269-1 2-1437269-2 2-1437269-3 2-1437269-4 2-1437269-5 2-1437269-7 2-1437269-8 2-1437269-9 2-1437270-0 2-1437270-1 2-1437270-2 2-1437270-3 2-1437270-4 2-1437270-6 2-1437270-7 2-1437270-8 2-1437270-9 2-1437273-0 2-1437273-1 2-1437273-2 2-1437273-3 2-1437273-4 2-1437273-5 2-1437273-6 2-1437273-7 2-1437273-8 2-1437273-9 2-1437274-0 2-1437274-2 2-1437274-3 2-1437274-4 2-1437274-5 2-1437274-6 2-1437274-7 2-1437274-8 2-1437274-9 2-1437275-9 2-1437276-0 2-1437276-1 2-1437276-2 2-1437276-3 2-1437276-5 2-1437276-6 2-1437276-7 2-1437276-9 3-1437260-0 3-1437260-5 3-1437260-6 Acquired Part Number C7D28PF29013 C7D28PF29023 C1D50PF29013 C1D50PF29015 C1D50PF29017 W8D30PF29013 W8D30PF29043 W8D35PF29013 W8D35PF29063 W8D36PF29013 W8D36PF29043 W8D36PF29093 A6D15RA29E A6D15WW29A3 A6D18DS29A2 A6D18DS29C2 A6D18RA29A A6D18WW29A3 A6D22DS29A2 A6D22DS29B2 A6D22DS29C2 A7D25DS29A2 A7D25RA29FM232 A7D28DS29A2 A7D28DS29B2 A7D28DS29C2 A7D28RA29AM231 A7D28RA29C A8D10DS29C2 A8D10RA29A A8D10RA29C A8D10RA29CM233 A8D10RA29E A8D10WW29A3 A8D12DS29A2 A8D12DS29C2 A8D12RA29C A8D36RA29A A8D36RA29C A8D36RA29E A8D36RA29EM233 A8D36WW29A3 A8D40DS29A3 A8D40DS29C2 A8D40RA29E A8D40WW29A3 C6D10DS29B3 C6D10DS29C1 C6D10DS29C4 C6D12DS29A4 C6D12DS29C1 C6D12DS29C3 C6D15DS29A1 C6D15DS29B3 C6D15DS29C1 C6D15DS29C3 C7D28DS29D3 C7D28DS29E3 C7D28PF29032 C7D30DS29A3 C7D30DS29C3 C7D30DS29C4 C7D30PF29032 C7D31DS29A3 C7D31DS29C3 C8D06DS29C1 C8D36DS29D1 C8D36DS29D2 C8D36DS29D3 C8D36DS29E3 C8D40DS29A1 C8D40DS29A3 C8D40DS29C1 C8D40DS29C3 C8D15PF29043 C8D20PF29023 C8D20PF29043 Page Number 144 142 131 131 132 134 134 134 136 134 134 136 56 54 54 54 56 54 54 54 54 49 51 49 49 49 51 52 43 46 46 47 46 44 43 43 46 46 46 46 47 44 43 43 46 44 39 39 40 40 39 39 39 39 39 39 36 36 142 36 36 37 142 36 36 31 31 31 32 32 31 32 31 32 140 138 140 Tyco Part Number 3-1437260-8 3-1437262-3 3-1437262-4 3-1437262-6 3-1437262-8 3-1437262-9 3-1437263-1 3-1437263-2 3-1437263-3 3-1437263-9 3-1437264-3 3-1437264-4 3-1437264-5 3-1437264-6 3-1437265-0 3-1437265-4 3-1437265-5 3-1437265-6 3-1437265-7 3-1437265-9 3-1437266-5 3-1437266-9 3-1437267-0 3-1437267-1 3-1437267-2 3-1437267-4 3-1437267-5 3-1437267-6 3-1437267-7 3-1437267-8 3-1437267-9 3-1437268-0 3-1437268-1 3-1437268-2 3-1437268-3 3-1437268-4 3-1437268-5 3-1437268-6 3-1437268-7 3-1437268-8 3-1437268-9 3-1437269-0 3-1437269-1 3-1437269-2 3-1437269-8 3-1437269-9 3-1437270-0 3-1437270-1 3-1437270-2 3-1437270-3 3-1437270-4 3-1437270-5 3-1437270-6 3-1437270-7 3-1437270-8 3-1437270-9 3-1437273-0 3-1437273-1 3-1437273-2 3-1437273-3 3-1437273-4 3-1437273-5 3-1437273-6 3-1437273-7 3-1437273-8 3-1437273-9 3-1437274-0 3-1437274-1 3-1437274-2 3-1437274-3 3-1437274-4 3-1437274-6 3-1437274-7 3-1437274-8 3-1437274-9 3-1437275-0 3-1437275-1 Acquired Part Number C8D22PF29013 C6D36PF29013 C6D36PF29023 C6D43PF29013 C6D43PF29022 C6D43PF29023 C7D30PF29013 C7D30PF29023 C7D30PF29043 C7D35PF29012 C6D36DS29C3 C9D020PF60048 C9D030PF60048 C9D060PF60048 W8D40PF29013 W8D50PF29012 W8D50PF29013 W8D50PF29043 W8D50PF29062 W8D60PF29013 98336 9836701 A6D22RA29A A6D22RA29C A6D22WW29A3 A6D25DS29C2 A6D28DS29A2 A6D28DS29C2 A6D28RA29A A6D28RA29C A6D28RA29E A7D28RA29CM232 A7D28RA29E A7D28RA29EM231 A7D28WW29A3 A7D30DS29A2 A7D30DS29C2 A7D30RA29AM231 A7D30WW29A3 A7D35DS29A2 A7D35DS29C2 A8D12RA29E A8D12RA29EM233 A8D12WW29A3 A8D15DS29A2 A8D15DS29C2 A8D43DS29C2 A8D43RA29A A8D43RA29C A8D43RA29E A8D43WW29A3 A8D44DS29A2 A8D44DS29C2 A8D44DS29C3 A8D44RA29CM233 A8D50DS29A2 C6D15DS29D1 C6D15DS29D3 C6D18DS29A1 C6D18DS29A3 C6D18DS29C1 C6D22DS29A1 C6D22DS29A3 C6D22DS29B4 C6D22DS29C1 C6D22DS29D1 C7D31DS29D3 C7D35DS29C1 C7D36DS29C1 C7D36DS29C3 C7D36DS29D3 C7D40DS29C1 C7D40DS29C3 C7D40DS29D3 C7D43DS29C1 C8D06DS29C2 C8D06DS29C3 Page Number 140 148 146 148 146 146 144 142 144 144 39 129 129 129 134 134 134 134 136 134 150 151 56 56 54 54 54 54 56 56 56 51 52 51 49 49 49 51 49 49 49 46 47 44 43 43 43 46 46 46 44 43 43 44 47 43 39 39 39 39 39 39 39 40 39 39 36 36 36 36 36 36 36 36 36 31 32 190 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Tyco Part Number to Acquired Part Number Tyco Part Number 3-1437275-2 3-1437275-5 3-1437275-6 3-1437275-8 3-1437275-9 3-1437276-0 3-1437276-1 3-1437276-2 3-1437276-3 3-1437276-4 3-1437276-5 3-1437276-8 3-1437276-9 4-1437260-0 4-1437260-1 4-1437260-5 4-1437260-8 4-1437260-9 4-1437262-0 4-1437263-0 4-1437263-1 4-1437263-2 4-1437263-3 4-1437263-4 4-1437263-5 4-1437263-6 4-1437263-7 4-1437263-8 4-1437267-0 4-1437267-1 4-1437267-2 4-1437267-3 4-1437267-4 4-1437267-5 4-1437267-6 4-1437267-7 4-1437267-8 4-1437267-9 4-1437268-0 4-1437268-1 4-1437268-2 4-1437268-3 4-1437268-4 4-1437268-6 4-1437268-8 4-1437268-9 4-1437269-0 4-1437269-1 4-1437269-2 4-1437269-3 4-1437269-4 4-1437269-5 4-1437269-6 4-1437269-8 4-1437269-9 4-1437270-0 4-1437270-1 4-1437270-2 4-1437270-4 4-1437270-5 4-1437270-6 4-1437270-7 4-1437273-0 4-1437273-1 4-1437273-2 4-1437273-3 4-1437273-4 4-1437273-6 4-1437273-7 4-1437273-8 4-1437273-9 4-1437274-0 4-1437274-1 4-1437274-3 4-1437274-4 4-1437274-5 4-1437274-6 Acquired Part Number C8D06DS29E1 C8D10DS29A3 C8D10DS29C1 C8D10DS29C2 C8D10DS29C3 C8D40DS29D1 C8D40DS29D3 C8D43DS29C1 C8D43DS29C3 C8D43DS29D3 C8D43DS29E1 C8D50DS29A1 C8D50DS29A3 C8D22PF29023 C8D22PF29043 C8D25PF29013 C8D25PF29023 C8D25PF29033 C6D43PF29043 C7D35PF29013 C7D36PF29012 C7D36PF29013 C7D36PF29033 C7D40PF29012 C7D40PF29013 C7D40PF29023 C7D40PF29032 C7D40PF29043 A6D28RA29EM233 A6D28WW29A3 A6D36DS29A2 A6D36DS29A3 A6D36DS29C2 A6D36RA29E A6D36WW29A3 A6D43DS29A2 A6D43DS29A3 A6D43DS29C2 A7D35RA29A A7D36DS29A2 A7D36DS29C2 A7D36RA29AM232 A7D36WW29A3 A7D40DS29C2 A7D40RA29E A7D40WW29A3 A8D15DS29D2 A8D15RA29C A8D15RA29CM233 A8D15RA29E A8D15RA29EM233 A8D15RA29FM233 A8D15WW29A3 A8D18DS29A2 A8D18DS29C2 A8D50DS29C2 A8D50DS29C3 A8D50DS29D2 A8D50RA29C A8D50RA29E A8D50RA29F A8D50WW29A3 C6D22DS29D3 C6D25DS29A3 C6D25DS29C3 C6D25DS29D1 C6D28DS29C1 C6D28DS29C3 C6D28DS29D1 C6D30DS29C1 C6D30DS29C3 C7D43DS29C3 C7D43DS29D4 C7D50DS29A3 C7D50DS29C1 C7D50DS29C3 C7D50DS29C4 Tyco Part Number Page Number 31 32 31 31 32 31 32 31 32 32 31 31 32 138 140 140 138 138 148 144 144 144 142 144 144 142 142 144 56 54 54 54 54 56 54 54 54 54 52 49 49 51 49 49 52 49 43 46 47 46 47 47 44 43 43 43 44 43 46 46 46 44 39 39 39 39 39 39 39 39 39 36 37 36 36 36 37 4-1437274-8 4-1437275-0 4-1437275-1 4-1437275-5 4-1437275-7 4-1437275-8 4-1437276-0 4-1437276-2 4-1437276-3 4-1437276-6 4-1437276-7 5-1437260-5 5-1437260-6 5-1437260-8 5-1437263-0 5-1437263-1 5-1437263-2 5-1437263-3 5-1437263-4 5-1437263-7 5-1437267-0 5-1437267-1 5-1437267-2 5-1437267-3 5-1437267-4 5-1437268-0 5-1437268-2 5-1437268-3 5-1437268-4 5-1437268-5 5-1437268-6 5-1437268-8 5-1437269-0 5-1437269-1 5-1437269-2 5-1437269-3 5-1437269-4 5-1437269-6 5-1437269-7 5-1437269-8 5-1437269-9 5-1437270-1 5-1437270-2 5-1437270-3 5-1437270-5 5-1437270-6 5-1437270-9 5-1437273-0 5-1437273-1 5-1437273-2 5-1437273-3 5-1437273-4 5-1437273-5 5-1437273-6 5-1437273-7 5-1437273-8 5-1437273-9 5-1437274-0 5-1437274-1 5-1437275-1 5-1437275-2 5-1437275-4 5-1437275-5 5-1437275-6 5-1437275-9 5-1437276-1 5-1437276-2 5-1437276-3 5-1437276-4 5-1437276-7 5-1437276-8 6-1437260-1 6-1437260-4 6-1437260-5 6-1437260-6 6-1437260-7 6-1437260-8 Acquired Part Number C7D50DS29D3 C8D10DS29D1 C8D10DS29D3 C8D12DS29C1 C8D12DS29C3 C8D12DS29D1 C8D50DS29C1 C8D50DS29C3 C8D50DS29D1 C8D52DS29C1M191 C8D52DS29C1M195 C8D28PF29023 C8D30PF29013 C8D30PF29023 C7D43PF29013 C7D50DS29B3 C7D50PF29013 C7D50PF29033 C7D50PF29043 C7D50PF29143 A6D43DS29C3 A6D43RA29AM233 A6D43RA29C A6D43RA29E A6D43WW29A3 A7D40WW29B3 A7D43DS29A2 A7D43DS29C2 A7D43WW29A3 A7D50DS29A2 A7D50DS29C2 A7D50DS29D2 A8D18DS29C3 A8D18RA29C A8D18RA29CM233 A8D18RA29FM233 A8D18WW29A3 A8D20DS29B2 A8D20DS29C2 A8D20RA29C A8D20RA29E A8D60DS29A2 A8D60DS29C2 A8D60DS29C3 A8D60RA29A A8D60WW29A3 A8D65DS29C2 C6D30DS29D3 C6D30DS29D4 C6D31DS29A1 C6D36DS29A3 C6D36DS29C1 C6D36DS29D1 C6D36DS29D4 C6D36DS29E4 C6D40DS29B3 C6D43DS29A1 C7D50DS29E1 C8D12DS29E1 C8D15DS29B3 C8D15DS29C1 C8D15DS29C3 C8D15DS29D1 C8D15DS29D2 C8D18DS29C1 C8D60DS29A1 C8D60DS29A3 C8D60DS29B3 C8D60DS29C1 C8D60DS29D1 C8D60PF29013 C8D30PF29043 C8D30PF29133 C8D31PF29013 C8D31PF29023 C8D31PF29043 C8D31PF29132 Page Number 36 31 32 31 32 31 31 32 31 29 29 138 140 138 144 36 144 142 144 142 54 56 56 56 54 49 49 49 49 49 49 49 43 46 47 47 44 43 43 46 46 43 43 44 46 44 43 39 40 39 39 39 39 40 40 39 39 36 31 32 31 32 31 31 31 31 32 32 31 31 140 140 140 140 138 140 140 Tyco Part Number 6-1437260-9 6-1437268-0 6-1437268-1 6-1437268-2 6-1437269-0 6-1437269-1 6-1437269-2 6-1437269-4 6-1437269-5 6-1437269-6 6-1437269-7 6-1437269-8 6-1437269-9 6-1437270-0 6-1437270-6 6-1437273-0 6-1437273-1 6-1437273-2 6-1437273-4 6-1437273-6 6-1437275-1 6-1437275-2 6-1437275-3 6-1437275-4 6-1437275-6 6-1437275-8 6-1437275-9 7-1437260-3 7-1437260-7 7-1437260-9 7-1437269-0 7-1437269-1 7-1437269-2 7-1437269-3 7-1437269-4 7-1437269-5 7-1437269-6 7-1437269-7 7-1437269-8 7-1437269-9 7-1437275-0 7-1437275-1 7-1437275-2 7-1437275-3 7-1437275-4 7-1437275-6 7-1437275-7 7-1437275-8 7-1437275-9 8-1437260-0 8-1437260-1 8-1437260-2 8-1437260-4 8-1437260-6 8-1437260-9 8-1437269-1 8-1437269-2 8-1437269-3 8-1437269-5 8-1437269-6 8-1437269-7 8-1437269-9 8-1437275-0 8-1437275-2 8-1437275-3 8-1437275-4 8-1437275-5 8-1437275-8 8-1437275-9 9-1437260-0 9-1437260-2 9-1437260-3 9-1437260-9 9-1437269-0 9-1437269-1 9-1437269-2 9-1437269-3 Acquired Part Number C8D31PF29133 A7D50RA29A A7D50WW29A3 A7D50WW29B3 A8D20WW29A3 A8D22DS29A2 A8D22DS29C2 A8D22RA29A A8D22RA29C A8D22RA29E A8D22RA29EM233 A8D22WW29A3 A8D25DS29A2 A8D65DS29D2 A8D28RA29C C6D43DS29A4 C6D43DS29B1 C6D43DS29C1 C6D43DS29C3 C6D43DS29D3 C8D18DS29C3 C8D18DS29D1 C8D18DS29D3 C8D18DS29E1 C8D20DS29C1 C8D20DS29C3 C8D20DS29D1 C8D35PF29023 C8D36PF29013 C8D36PF29022 A8D25DS29B2 A8D25DS29C2 A8D25DS29C3 A8D25RA29A A8D25RA29AM233 A8D25RA29C A8D25RA29CM233 A8D25RA29E A8D25RA29FM233 A8D25WW29A3 C8D20DS29D3 C8D22DS29A1 C8D22DS29A3 C8D22DS29B1 C8D22DS29C1 C8D22DS29C3 C8D22DS29D1 C8D25DS29A1 C8D25DS29A3 C8D36PF29023 C8D36PF29033 C8D36PF29043 C8D40PF29023 C8D40PF29043 C8D43PF29012 A8D28DS29A2 A8D28DS29C2 A8D28RA29E A8D30DS29A2 A8D30DS29B2 A8D30DS29C2 A8D30DS29C3 C8D25DS29C1 C8D25DS29C3 C8D25DS29D1 C8D25DS29D3 C8D28DS29C1 C8D28DS29C3 C8D28DS29D1 C8D43PF29013 C8D43PF29022 C8D43PF29023 C8D50PF29013 A8D30DS29D2 A8D30DS29D2 A8D30RA29C A8D30RA29E Page Number 140 52 49 49 44 43 43 46 46 46 47 44 43 43 46 40 39 39 39 39 32 31 32 31 31 32 31 138 140 138 43 43 43 46 47 46 47 46 47 44 32 31 32 31 31 32 31 31 32 138 138 140 138 140 140 43 43 46 43 43 43 43 31 32 31 32 31 32 31 140 138 138 140 43 43 46 46 191 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Tyco Part Number to Acquired Part Number Tyco Part Number 9-1437269-4 9-1437269-5 9-1437269-8 9-1437269-9 9-1437275-0 9-1437275-1 9-1437275-3 9-1437275-5 9-1437275-6 9-1437275-7 9-1437275-8 9-1437275-9 AP3 BMEP 1K/2K BMEP 3T/5T MEP 6T/12T Model G SAHT Acquired Part Number A8D30WW29A3 A8D30WW29B3 A8D31DS29A2 A8D31DS29A3 C8D28DS29D3 C8D28PF29012 C8D30DS29C1 C8D30DS29C3 C8D30DS29D1 C8D30DS29D3 C8D30DS29E1 C8D30DS29E3 — — — — — — Page Number 44 44 43 43 32 140 31 32 31 32 31 32 149 149 149 149 184 185 192 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number 98206 98224 98230 98231 98236 98238 98293 98336 9818001 9818002 9818003 9818004 9818005 9820301 9820302 9820303 9820305 9820401 9836301 9836701 9836702 A6D06DS29A2 A6D06DS29A3 A6D06DS29B2 A6D06DS29B3 A6D06DS29C2 A6D06DS29C3 A6D06RA29A A6D06RA29AM233 A6D06RA29C A6D06RA29CM233 A6D06RA29E A6D06RA29EM233 A6D06RA29F A6D06RA29FM233 A6D06WW29A3 A6D06WW29B3 A6D10DS29A2 A6D10DS29A3 A6D10DS29B2 A6D10DS29B3 A6D10DS29C2 A6D10DS29C3 A6D10RA29A A6D10RA29AM233 A6D10RA29C A6D10RA29CM233 A6D10RA29E A6D10RA29EM233 A6D10RA29F A6D10RA29FM233 A6D10WW29A3 A6D10WW29B3 A6D12DS29A2 A6D12DS29A3 A6D12DS29B2 A6D12DS29B3 A6D12DS29C2 A6D12DS29C3 A6D12RA29A A6D12RA29AM233 A6D12RA29C A6D12RA29CM233 A6D12RA29E A6D12RA29EM233 A6D12RA29F A6D12RA29FM233 A6D12WW29A3 A6D12WW29B3 A6D15DS29A2 A6D15DS29A3 A6D15DS29B2 A6D15DS29B3 A6D15DS29C2 A6D15DS29C3 A6D15RA29A A6D15RA29AM233 A6D15RA29C A6D15RA29CM233 A6D15RA29E A6D15RA29EM233 A6D15RA29F A6D15RA29FM233 A6D15WW29A3 A6D15WW29B3 A6D18DS29A2 A6D18DS29A3 A6D18DS29B2 Tyco Part Number 1437266-8 1437266-9 1-1437266-0 1-1437266-1 1-1437266-6 1-1437266-8 1437274-1 3-1437266-5 — 1437266-3 — 1437266-4 1437266-5 1437266-6 1437260-4 — 1437260-5 1437266-7 1437260-6 3-1437266-9 1437260-7 — 0-1437267-5 — — — — — — — — — — — — — — 0-1437267-6 — — — 0-1437267-7 0-1437267-8 0-1437267-9 1-1437267-0 1-1437267-1 — 1-1437267-2 — — — 1-1437267-3 — — — — — 1-1437267-4 — 1-1437267-5 — — — — — — — 1-1437267-6 — 1-1437267-7 — — — 1-1437267-9 — — — — — 2-1437267-0 — — — 2-1437267-1 — 2-1437267-2 — — Acquired Part Number Tyco Part Number A6D18DS29B3 A6D18DS29C2 A6D18DS29C3 A6D18RA29A A6D18RA29AM233 A6D18RA29C A6D18RA29CM233 A6D18RA29E A6D18RA29EM233 A6D18RA29F A6D18RA29FM233 A6D18WW29A3 A6D18WW29B3 A6D22DS29A2 A6D22DS29A3 A6D22DS29B2 A6D22DS29B3 A6D22DS29C2 A6D22DS29C3 A6D22RA29A A6D22RA29AM233 A6D22RA29C A6D22RA29CM233 A6D22RA29E A6D22RA29EM233 A6D22RA29F A6D22RA29FM233 A6D22WW29A3 A6D22WW29B3 A6D25DS29A2 A6D25DS29A3 A6D25DS29B2 A6D25DS29B3 A6D25DS29C2 A6D25DS29C3 A6D25RA29A A6D25RA29AM233 A6D25RA29C A6D25RA29CM233 A6D25RA29E A6D25RA29EM233 A6D25RA29F A6D25RA29FM233 A6D25WW29A3 A6D25WW29B3 A6D28DS29A2 A6D28DS29A3 A6D28DS29B2 A6D28DS29B3 A6D28DS29C2 A6D28DS29C3 A6D28RA29A A6D28RA29AM233 A6D28RA29C A6D28RA29CM233 A6D28RA29E A6D28RA29EM233 A6D28RA29F A6D28RA29FM233 A6D28WW29A3 A6D28WW29B3 A6D36DS29A2 A6D36DS29A3 A6D36DS29B2 A6D36DS29B3 A6D36DS29C2 A6D36DS29C3 A6D36RA29A A6D36RA29AM233 A6D36RA29C A6D36RA29CM233 A6D36RA29E A6D36RA29EM233 A6D36RA29F A6D36RA29FM233 A6D36WW29A3 A6D36WW29B3 A6D40RA29A A6D40RA29AM233 A6D40RA29C A6D40RA29CM233 A6D40RA29E A6D40RA29EM233 A6D40RA29F A6D40RA29FM233 A6D43DS29A2 A6D43DS29A3 A6D43DS29B2 — 2-1437267-3 — 2-1437267-4 — — — — — — — 2-1437267-5 — 2-1437267-7 — 2-1437267-8 — 2-1437267-9 — 3-1437267-0 — 3-1437267-1 — — — — — 3-1437267-2 — — — — — 3-1437267-4 — — — — — — — — — — — 3-1437267-5 — — — 3-1437267-6 — 3-1437267-7 — 3-1437267-8 — 3-1437267-9 4-1437267-0 — — 4-1437267-1 — 4-1437267-2 4-1437267-3 — — 4-1437267-4 — — — — — 4-1437267-5 — — — 4-1437267-6 — — — — — — — — — 4-1437267-7 4-1437267-8 — Page Number 150 150 150 150 150 150 150 150 151 151 151 151 151 151 151 151 151 151 151 151 151 54 54 54 54 54 54 56 56 56 56 56 56 56 56 54 54 54 54 54 54 54 54 56 56 56 56 56 56 56 56 54 54 54 54 54 54 54 54 54 56 56 56 56 56 56 56 54 54 54 54 54 54 54 54 56 56 56 56 56 56 56 56 54 54 54 54 54 Page Number 54 54 54 56 56 56 56 56 56 56 56 54 54 54 54 54 54 54 54 56 56 56 56 56 56 56 56 54 54 54 54 54 54 54 54 56 56 56 56 56 56 56 56 54 54 54 54 54 54 54 54 56 56 56 56 56 56 56 56 54 54 54 54 54 54 54 54 56 56 56 56 56 56 56 56 54 54 56 56 56 56 56 56 56 56 54 54 54 Acquired Part Number Tyco Part Number A6D43DS29B3 A6D43DS29C2 A6D43DS29C3 A6D43RA29A A6D43RA29AM233 A6D43RA29C A6D43RA29CM233 A6D43RA29E A6D43RA29EM233 A6D43RA29F A6D43RA29FM233 A6D43WW29A3 A6D43WW29B3 A7D06DS29A2 A7D06DS29B2 A7D06DS29C2 A7D06DS29D2 A7D06DS29E2 A7D06RA29A A7D06RA29AM231 A7D06RA29AM232 A7D06RA29C A7D06RA29CM231 A7D06RA29CM232 A7D06RA29E A7D06RA29EM231 A7D06RA29EM232 A7D06RA29F A7D06RA29FM231 A7D06RA29FM232 A7D06WW29A3 A7D06WW29B3 A7D10DS29A2 A7D10DS29B2 A7D10DS29C2 A7D10DS29D2 A7D10DS29E2 A7D10RA29A A7D10RA29AM231 A7D10RA29AM232 A7D10RA29C A7D10RA29CM231 A7D10RA29CM232 A7D10RA29E A7D10RA29EM231 A7D10RA29EM232 A7D10RA29F A7D10RA29FM231 A7D10RA29FM232 A7D10WW29A3 A7D10WW29B3 A7D15DS29A2 A7D15DS29B2 A7D15DS29C2 A7D15DS29D2 A7D15DS29E2 A7D15RA29A A7D15RA29AM231 A7D15RA29AM232 A7D15RA29C A7D15RA29CM231 A7D15RA29CM232 A7D15RA29E A7D15RA29EM231 A7D15RA29EM232 A7D15RA29F A7D15RA29FM231 A7D15RA29FM232 A7D15WW29A3 A7D15WW29B3 A7D18DS29A2 A7D18DS29B2 A7D18DS29C2 A7D18DS29D2 A7D18DS29E2 A7D18RA29A A7D18RA29AM231 A7D18RA29AM232 A7D18RA29C A7D18RA29CM231 A7D18RA29CM232 A7D18RA29E A7D18RA29EM231 A7D18RA29EM232 A7D18RA29F A7D18RA29FM231 A7D18RA29FM232 A7D18WW29A3 — 4-1437267-9 5-1437267-0 — 5-1437267-1 5-1437267-2 — 5-1437267-3 — — — 5-1437267-4 — — — 0-1437268-4 — — — — — 0-1437268-5 — — 0-1437268-6 — — — — — — — — — 0-1437268-7 — — — 0-1437268-8 — — — — — — — — — — 0-1437268-9 — 1-1437268-1 — 1-1437268-2 — — — — — 1-1437268-3 — — 1-1437268-4 — — — — — 1-1437268-5 — 1-1437268-6 1-1437268-7 — — — — — — — — — — — — — — — 1-1437268-8 Page Number 54 54 54 56 56 56 56 56 56 56 56 54 54 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 193 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number A7D18WW29B3 A7D22DS29A2 A7D22DS29B2 A7D22DS29C2 A7D22RA29A A7D22RA29AM231 A7D22RA29AM232 A7D22RA29C A7D22RA29CM231 A7D22RA29CM232 A7D22RA29E A7D22RA29EM231 A7D22RA29EM232 A7D22RA29F A7D22RA29FM231 A7D22RA29FM232 A7D22WW29A3 A7D22WW29B3 A7D25DS29A2 A7D25DS29B2 A7D25DS29C2 A7D25DS29D2 A7D25DS29E2 A7D25RA29A A7D25RA29AM231 A7D25RA29AM232 A7D25RA29C A7D25RA29CM231 A7D25RA29CM232 A7D25RA29E A7D25RA29EM231 A7D25RA29EM232 A7D25RA29F A7D25RA29FM231 A7D25RA29FM232 A7D25WW29A3 A7D25WW29B3 A7D28DS29A2 A7D28DS29B2 A7D28DS29C2 A7D28RA29A A7D28RA29AM231 A7D28RA29AM232 A7D28RA29C A7D28RA29CM231 A7D28RA29CM232 A7D28RA29E A7D28RA29EM231 A7D28RA29EM232 A7D28RA29F A7D28RA29FM231 A7D28RA29FM232 A7D28WW29A3 A7D28WW29B3 A7D30DS29A2 A7D30DS29B2 A7D30DS29C2 A7D30DS29D2 A7D30DS29E2 A7D30RA29A A7D30RA29AM231 A7D30RA29AM232 A7D30RA29C A7D30RA29CM231 A7D30RA29CM232 A7D30RA29E A7D30RA29EM231 A7D30RA29EM232 A7D30RA29F A7D30RA29FM231 A7D30RA29FM232 A7D30WW29A3 A7D30WW29B3 A7D35DS29A2 A7D35DS29B2 A7D35DS29C2 A7D35RA29A A7D35RA29AM231 A7D35RA29AM232 A7D35RA29C A7D35RA29CM231 A7D35RA29CM232 A7D35RA29E A7D35RA29EM231 A7D35RA29EM232 A7D35RA29F A7D35RA29FM231 A7D35RA29FM232 Tyco Part Number — — — 1-1437268-9 — — — — — — — — — — — — — — 2-1437268-1 — — — — — — — — — — — — — — — 2-1437268-2 — — 2-1437268-3 2-1437268-4 2-1437268-5 — 2-1437268-8 — 2-1437268-9 — 3-1437268-0 3-1437268-1 3-1437268-2 — — — — 3-1437268-3 — 3-1437268-4 — 3-1437268-5 — — — 3-1437268-6 — — — — — — — — — — 3-1437268-7 — 3-1437268-8 — 3-1437268-9 4-1437268-0 — — — — — — — — — — — Acquired Part Number Tyco Part Number A7D35WW29A3 A7D35WW29B3 A7D36DS29A2 A7D36DS29B2 A7D36DS29C2 A7D36RA29A A7D36RA29AM231 A7D36RA29AM232 A7D36RA29C A7D36RA29CM231 A7D36RA29CM232 A7D36RA29E A7D36RA29EM231 A7D36RA29EM232 A7D36RA29F A7D36RA29FM231 A7D36RA29FM232 A7D36WW29A3 A7D36WW29B3 A7D40DS29A2 A7D40DS29B2 A7D40DS29C2 A7D40RA29A A7D40RA29AM231 A7D40RA29AM232 A7D40RA29C A7D40RA29CM231 A7D40RA29CM232 A7D40RA29E A7D40RA29EM231 A7D40RA29EM232 A7D40RA29F A7D40RA29FM231 A7D40RA29FM232 A7D40WW29A3 A7D40WW29B3 A7D43DS29A2 A7D43DS29B2 A7D43DS29C2 A7D43RA29A A7D43RA29AM231 A7D43RA29AM232 A7D43RA29C A7D43RA29CM231 A7D43RA29CM232 A7D43RA29E A7D43RA29EM231 A7D43RA29EM232 A7D43RA29F A7D43RA29FM231 A7D43RA29FM232 A7D43WW29A3 A7D43WW29B3 A7D50DS29A2 A7D50DS29B2 A7D50DS29C2 A7D50DS29D2 A7D50DS29E2 A7D50RA29A A7D50RA29AM231 A7D50RA29AM232 A7D50RA29C A7D50RA29CM231 A7D50RA29CM232 A7D50RA29E A7D50RA29EM231 A7D50RA29EM232 A7D50RA29F A7D50RA29FM231 A7D50RA29FM232 A7D50WW29A3 A7D50WW29B3 A8D10DS29A2 A8D10DS29A3 A8D10DS29B2 A8D10DS29B3 A8D10DS29C2 A8D10DS29C3 A8D10DS29D2 A8D10DS29D3 A8D10DS29E2 A8D10DS29E3 A8D10RA29A A8D10RA29AM233 A8D10RA29C A8D10RA29CM233 A8D10RA29E A8D10RA29EM233 — — 4-1437268-1 — 4-1437268-2 — — 4-1437268-3 — — — — — — — — — 4-1437268-4 — — — 4-1437268-6 — — — — — — 4-1437268-8 — — — — — 4-1437268-9 5-1437268-0 5-1437268-2 — 5-1437268-3 — — — — — — — — — — — — 5-1437268-4 — 5-1437268-5 — 5-1437268-6 5-1437268-8 — 6-1437268-0 — — — — — — — — — — — 6-1437268-1 6-1437268-2 1-1437269-9 — — — 2-1437269-0 — — — — — 2-1437269-1 — 2-1437269-2 2-1437269-3 2-1437269-4 — Page Number 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 Page Number 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 49 49 49 49 49 52 51 51 52 51 51 52 51 51 52 51 51 49 49 43 43 43 43 43 43 43 43 43 43 46 47 46 47 46 47 Acquired Part Number Tyco Part Number A8D10RA29F A8D10RA29FM233 A8D10WW29A3 A8D10WW29B3 A8D12DS29A2 A8D12DS29A3 A8D12DS29B2 A8D12DS29B3 A8D12DS29C2 A8D12DS29C3 A8D12RA29A A8D12RA29AM233 A8D12RA29C A8D12RA29CM233 A8D12RA29E A8D12RA29EM233 A8D12WW29A3 A8D12WW29B3 A8D15DS29A2 A8D15DS29A3 A8D15DS29B2 A8D15DS29B3 A8D15DS29C2 A8D15DS29C3 A8D15DS29D2 A8D15DS29D3 A8D15DS29E2 A8D15DS29E3 A8D15RA29A A8D15RA29AM233 A8D15RA29C A8D15RA29CM233 A8D15RA29E A8D15RA29EM233 A8D15RA29F A8D15RA29FM233 A8D15WW29A3 A8D15WW29B3 A8D18DS29A2 A8D18DS29A3 A8D18DS29B2 A8D18DS29B3 A8D18DS29C2 A8D18DS29C3 A8D18DS29D2 A8D18DS29D3 A8D18DS29E2 A8D18DS29E3 A8D18RA29A A8D18RA29AM233 A8D18RA29C A8D18RA29CM233 A8D18RA29E A8D18RA29EM233 A8D18RA29F A8D18RA29FM233 A8D18WW29A3 A8D18WW29B3 A8D20DS29A2 A8D20DS29A3 A8D20DS29B2 A8D20DS29B3 A8D20DS29C2 A8D20DS29C3 A8D20RA29A A8D20RA29AM233 A8D20RA29C A8D20RA29CM233 A8D20RA29E A8D20RA29EM233 A8D20WW29A3 A8D20WW29B3 A8D22DS29A2 A8D22DS29A3 A8D22DS29B2 A8D22DS29B3 A8D22DS29C2 A8D22DS29C3 A8D22RA29A A8D22RA29AM233 A8D22RA29C A8D22RA29CM233 A8D22RA29E A8D22RA29EM233 A8D22WW29A3 A8D22WW29B3 A8D25DS29A2 A8D25DS29A3 — — 2-1437269-5 — 2-1437269-7 — — — 2-1437269-8 — — — 2-1437269-9 — 3-1437269-0 3-1437269-1 3-1437269-2 — 3-1437269-8 — — — 3-1437269-9 — 4-1437269-0 — — — — — 4-1437269-1 4-1437269-2 4-1437269-3 4-1437269-4 — 4-1437269-5 4-1437269-6 — 4-1437269-8 — — — 4-1437269-9 5-1437269-0 — — — — — — 5-1437269-1 5-1437269-2 — — — 5-1437269-3 5-1437269-4 — — — 5-1437269-6 — 5-1437269-7 — — — 5-1437269-8 — 5-1437269-9 — 6-1437269-0 — 6-1437269-1 — — — 6-1437269-2 — 6-1437269-4 — 6-1437269-5 — 6-1437269-6 6-1437269-7 6-1437269-8 — 6-1437269-9 — Page Number 46 47 44 44 43 43 43 43 43 43 46 47 46 47 46 47 44 44 43 43 43 43 43 43 43 43 43 43 46 47 46 47 46 47 46 47 44 44 43 43 43 43 43 43 43 43 43 43 46 47 46 47 46 47 46 47 44 44 43 43 43 43 43 43 46 47 46 47 46 47 44 44 43 43 43 43 43 43 46 47 46 47 46 47 44 44 43 43 194 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number A8D25DS29B2 A8D25DS29B3 A8D25DS29C2 A8D25DS29C3 A8D25DS29D2 A8D25DS29D3 A8D25DS29E2 A8D25DS29E3 A8D25RA29A A8D25RA29AM233 A8D25RA29C A8D25RA29CM233 A8D25RA29E A8D25RA29EM233 A8D25RA29F A8D25RA29FM233 A8D25WW29A3 A8D25WW29B3 A8D28DS29A2 A8D28DS29A3 A8D28DS29B2 A8D28DS29B3 A8D28DS29C2 A8D28DS29C3 A8D28RA29A A8D28RA29AM233 A8D28RA29C A8D28RA29CM233 A8D28RA29E A8D28RA29EM233 A8D28WW29A3 A8D28WW29B3 A8D30DS29A2 A8D30DS29A3 A8D30DS29B2 A8D30DS29B3 A8D30DS29C2 A8D30DS29C3 A8D30DS29D2 A8D30DS29D2 A8D30DS29D3 A8D30DS29E2 A8D30DS29E3 A8D30RA29A A8D30RA29AM233 A8D30RA29C A8D30RA29CM233 A8D30RA29E A8D30RA29EM233 A8D30RA29F A8D30RA29FM233 A8D30WW29A3 A8D30WW29B3 A8D31DS29A2 A8D31DS29A3 A8D31DS29B2 A8D31DS29B3 A8D31DS29C2 A8D31DS29C3 A8D31DS29D2 A8D31DS29D3 A8D31DS29E2 A8D31DS29E3 A8D31RA29A A8D31RA29AM233 A8D31RA29C A8D31RA29CM233 A8D31RA29E A8D31RA29EM233 A8D31RA29F A8D31RA29FM233 A8D31WW29A3 A8D31WW29B3 A8D35DS29A2 A8D35DS29A3 A8D35DS29B2 A8D35DS29B3 A8D35DS29C2 A8D35DS29C3 A8D35RA29A A8D35RA29AM233 A8D35RA29C A8D35RA29CM233 A8D35RA29E A8D35RA29EM233 A8D35WW29A3 A8D35WW29B3 A8D36DS29A2 Tyco Part Number 7-1437269-0 — 7-1437269-1 7-1437269-2 — — — — 7-1437269-3 7-1437269-4 7-1437269-5 7-1437269-6 7-1437269-7 — — 7-1437269-8 7-1437269-9 — 8-1437269-1 — — — 8-1437269-2 — — — 6-1437270-6 — 8-1437269-3 — — — 8-1437269-5 — 8-1437269-6 — 8-1437269-7 8-1437269-9 9-1437269-0 9-1437269-1 — — — — — 9-1437269-2 — 9-1437269-3 — — — 9-1437269-4 9-1437269-5 9-1437269-8 9-1437269-9 — 0-1437270-1 0-1437270-2 — 0-1437270-3 — — — 0-1437270-4 — 0-1437270-6 0-1437270-7 0-1437270-8 — 0-1437270-9 — 1-1437270-0 — 1-1437270-2 — — — 1-1437270-3 — — — 1-1437270-4 — — — 1-1437270-5 — 1-1437270-6 Acquired Part Number Tyco Part Number A8D36DS29A3 A8D36DS29B2 A8D36DS29B3 A8D36DS29C2 A8D36DS29C3 A8D36RA29A A8D36RA29AM233 A8D36RA29C A8D36RA29CM233 A8D36RA29E A8D36RA29EM233 A8D36WW29A3 A8D36WW29B3 A8D40DS29A2 A8D40DS29A3 A8D40DS29B2 A8D40DS29B3 A8D40DS29C2 A8D40DS29C3 A8D40RA29A A8D40RA29AM233 A8D40RA29C A8D40RA29CM233 A8D40RA29E A8D40RA29EM233 A8D40WW29A3 A8D40WW29B3 A8D43DS29A2 A8D43DS29A3 A8D43DS29B2 A8D43DS29B3 A8D43DS29C2 A8D43DS29C3 A8D43RA29A A8D43RA29AM233 A8D43RA29C A8D43RA29CM233 A8D43RA29E A8D43RA29EM233 A8D43WW29A3 A8D43WW29B3 A8D44DS29A2 A8D44DS29A3 A8D44DS29B2 A8D44DS29B3 A8D44DS29C2 A8D44DS29C3 A8D44RA29A A8D44RA29AM233 A8D44RA29C A8D44RA29CM233 A8D44RA29E A8D44RA29EM233 A8D44WW29A3 A8D44WW29B3 A8D50DS29A2 A8D50DS29A3 A8D50DS29B2 A8D50DS29B3 A8D50DS29C2 A8D50DS29C3 A8D50DS29D2 A8D50DS29D3 A8D50DS29E2 A8D50DS29E3 A8D50RA29A A8D50RA29AM233 A8D50RA29C A8D50RA29CM233 A8D50RA29E A8D50RA29EM233 A8D50RA29F A8D50RA29FM233 A8D50WW29A3 A8D50WW29B3 A8D60DS29A2 A8D60DS29A3 A8D60DS29B2 A8D60DS29B3 A8D60DS29C2 A8D60DS29C3 A8D60RA29A A8D60RA29AM233 A8D60RA29C A8D60RA29CM233 A8D60RA29E A8D60RA29EM233 A8D60WW29A3 — — 1-1437270-7 1-1437270-8 1-1437270-9 2-1437270-0 — 2-1437270-1 — 2-1437270-2 2-1437270-3 2-1437270-4 — — 2-1437270-6 — — 2-1437270-7 — — — — — 2-1437270-8 — 2-1437270-9 — — — — — 3-1437270-0 — 3-1437270-1 — 3-1437270-2 — 3-1437270-3 — 3-1437270-4 — 3-1437270-5 — — — 3-1437270-6 3-1437270-7 — — — 3-1437270-8 — — — — 3-1437270-9 — — — 4-1437270-0 4-1437270-1 4-1437270-2 — — — — — 4-1437270-4 — 4-1437270-5 — 4-1437270-6 — 4-1437270-7 — 5-1437270-1 — — — 5-1437270-2 5-1437270-3 5-1437270-5 — — — — — 5-1437270-6 Page Number 43 43 43 43 43 43 43 43 46 47 46 47 46 47 46 47 44 44 43 43 43 43 43 43 46 47 46 47 46 47 44 44 43 43 43 43 43 43 43 43 43 43 43 46 47 46 47 46 47 46 47 44 44 43 43 43 43 43 43 43 43 43 43 46 47 46 47 46 47 46 47 44 44 43 43 43 43 43 43 46 47 46 47 46 47 44 44 43 Page Number 43 43 43 43 43 46 47 46 47 46 47 44 44 43 43 43 43 43 43 46 47 46 47 46 47 44 44 43 43 43 43 43 43 46 47 46 47 46 47 44 44 43 44 43 44 43 44 46 47 46 47 46 47 44 44 43 44 43 44 43 44 43 44 43 44 46 47 46 47 46 47 46 47 44 44 43 44 43 44 43 44 46 47 46 47 46 47 44 Acquired Part Number Tyco Part Number A8D60WW29B3 A8D65DS29A2 A8D65DS29A3 A8D65DS29B2 A8D65DS29B3 A8D65DS29C2 A8D65DS29C3 A8D65DS29D2 A8D65DS29D3 A8D65DS29E2 A8D65DS29E3 A8D65RA29A A8D65RA29AM233 A8D65RA29C A8D65RA29CM233 A8D65RA29E A8D65RA29EM233 A8D65RA29F A8D65RA29FM233 A8D65WW29A3 A8D65WW29B3 C1D18PF29013 C1D18PF29015 C1D18PF29017 C1D18PF29043 C1D18PF29045 C1D18PF29047 C1D18PF29133 C1D18PF29135 C1D18PF29137 C1D20PF29013 C1D20PF29015 C1D20PF29017 C1D20PF29043 C1D20PF29045 C1D20PF29047 C1D20PF29133 C1D20PF29135 C1D20PF29137 C1D22PF29013 C1D22PF29015 C1D22PF29017 C1D22PF29043 C1D22PF29045 C1D22PF29047 C1D22PF29133 C1D22PF29135 C1D22PF29137 C1D25PF29013 C1D25PF29015 C1D25PF29017 C1D25PF29043 C1D25PF29045 C1D25PF29047 C1D25PF29133 C1D25PF29135 C1D25PF29137 C1D28PF29013 C1D28PF29015 C1D28PF29017 C1D28PF29043 C1D28PF29045 C1D28PF29047 C1D28PF29133 C1D28PF29135 C1D28PF29137 C1D30PF29013 C1D30PF29015 C1D30PF29017 C1D30PF29043 C1D30PF29045 C1D30PF29047 C1D30PF29133 C1D30PF29135 C1D30PF29137 C1D35PF29013 C1D35PF29015 C1D35PF29017 C1D35PF29043 C1D35PF29045 C1D35PF29047 C1D35PF29133 C1D35PF29135 C1D35PF29137 C1D36PF29013 C1D36PF29015 C1D36PF29017 C1D36PF29043 — — — — — 5-1437270-9 — 6-1437270-0 — — — — — — — — — — — — — — 0-1437264-3 — — — — — — — — 0-1437264-6 — 0-1437264-7 — — — — — — — — — — — — — — 0-1437264-9 1-1437264-0 — — — — — — — — — — — — — — — — — — — — — — — — — 1-1437264-5 1-1437264-6 — — — — — — — — — — — Page Number 44 43 44 43 44 43 44 43 44 43 44 46 47 46 47 46 47 46 47 44 44 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 195 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number C1D36PF29045 C1D36PF29047 C1D36PF29133 C1D36PF29135 C1D36PF29137 C1D40PF29013 C1D40PF29015 C1D40PF29017 C1D40PF29043 C1D40PF29045 C1D40PF29047 C1D40PF29133 C1D40PF29135 C1D40PF29137 C1D43PF29013 C1D43PF29015 C1D43PF29017 C1D43PF29043 C1D43PF29045 C1D43PF29047 C1D43PF29133 C1D43PF29135 C1D43PF29137 C1D45PF29013 C1D45PF29015 C1D45PF29017 C1D45PF29043 C1D45PF29045 C1D45PF29047 C1D45PF29133 C1D45PF29135 C1D45PF29137 C1D50PF29013 C1D50PF29015 C1D50PF29017 C1D50PF29043 C1D50PF29045 C1D50PF29047 C1D50PF29133 C1D50PF29135 C1D50PF29137 C1D60PF29013 C1D60PF29015 C1D60PF29017 C1D60PF29043 C1D60PF29045 C1D60PF29047 C1D60PF29133 C1D60PF29135 C1D60PF29137 C6D06DS29A1 C6D06DS29A3 C6D06DS29A4 C6D06DS29B1 C6D06DS29B3 C6D06DS29B4 C6D06DS29C1 C6D06DS29C3 C6D06DS29C4 C6D06DS29D1 C6D06DS29D3 C6D06DS29D4 C6D06DS29E1 C6D06DS29E3 C6D06DS29E4 C6D06PF29012 C6D06PF29013 C6D06PF29022 C6D06PF29023 C6D06PF29032 C6D06PF29033 C6D06PF29042 C6D06PF29043 C6D06PF29132 C6D06PF29133 C6D06PF29142 C6D06PF29143 C6D10DS29A1 C6D10DS29A3 C6D10DS29A4 C6D10DS29B1 C6D10DS29B3 C6D10DS29B4 C6D10DS29C1 C6D10DS29C3 C6D10DS29C4 C6D10DS29D1 C6D10DS29D3 Tyco Part Number — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 2-1437264-2 2-1437264-3 2-1437264-4 — — — — — — — — — — — — — — — 1-1437273-3 — — — — — 1-1437273-4 1-1437273-5 — 1-1437273-6 1-1437273-7 1-1437273-8 — — — — 0-1437262-4 — — — — — 0-1437262-5 — — — — 1-1437273-9 — — — 2-1437273-0 — 2-1437273-1 — 2-1437273-2 — — Page Number 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 131 131 132 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 Acquired Part Number C6D10DS29D4 C6D10DS29E1 C6D10DS29E3 C6D10DS29E4 C6D10PF29012 C6D10PF29013 C6D10PF29022 C6D10PF29023 C6D10PF29032 C6D10PF29033 C6D10PF29042 C6D10PF29043 C6D10PF29132 C6D10PF29133 C6D10PF29142 C6D10PF29143 C6D12DS29A1 C6D12DS29A3 C6D12DS29A4 C6D12DS29B1 C6D12DS29B3 C6D12DS29B4 C6D12DS29C1 C6D12DS29C3 C6D12DS29C4 C6D12DS29D1 C6D12DS29D3 C6D12DS29D4 C6D12DS29E1 C6D12DS29E3 C6D12DS29E4 C6D12PF29012 C6D12PF29013 C6D12PF29022 C6D12PF29023 C6D12PF29032 C6D12PF29033 C6D12PF29042 C6D12PF29043 C6D12PF29132 C6D12PF29133 C6D12PF29142 C6D12PF29143 C6D15DS29A1 C6D15DS29A3 C6D15DS29A4 C6D15DS29B1 C6D15DS29B3 C6D15DS29B4 C6D15DS29C1 C6D15DS29C3 C6D15DS29C4 C6D15DS29D1 C6D15DS29D3 C6D15DS29D4 C6D15DS29E1 C6D15DS29E3 C6D15DS29E4 C6D15PF29012 C6D15PF29013 C6D15PF29022 C6D15PF29023 C6D15PF29032 C6D15PF29033 C6D15PF29042 C6D15PF29043 C6D15PF29132 C6D15PF29133 C6D15PF29142 C6D15PF29143 C6D18DS29A1 C6D18DS29A3 C6D18DS29A4 C6D18DS29B1 C6D18DS29B3 C6D18DS29B4 C6D18DS29C1 C6D18DS29C3 C6D18DS29C4 C6D18DS29D1 C6D18DS29D3 C6D18DS29D4 C6D18DS29E1 C6D18DS29E3 C6D18DS29E4 C6D18PF29012 C6D18PF29013 C6D18PF29022 Tyco Part Number Page Number — — — — — — 0-1437262-6 — — — — 0-1437262-7 — — — — — — 2-1437273-3 — — — 2-1437273-4 2-1437273-5 — — — — — — — — — — — — — — — — — — — 2-1437273-6 — — — 2-1437273-7 — 2-1437273-8 2-1437273-9 — 3-1437273-0 3-1437273-1 — — — — — — 0-1437262-9 1-1437262-0 — — — — — — — — 3-1437273-2 3-1437273-3 — — — — 3-1437273-4 — — — — — — — — — 1-1437262-3 — 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 Acquired Part Number Tyco Part Number C6D18PF29023 C6D18PF29032 C6D18PF29033 C6D18PF29042 C6D18PF29043 C6D18PF29132 C6D18PF29133 C6D18PF29142 C6D18PF29143 C6D20DS29A1 C6D20DS29A3 C6D20DS29A4 C6D20DS29B1 C6D20DS29B3 C6D20DS29B4 C6D20DS29C1 C6D20DS29C3 C6D20DS29C4 C6D20DS29D1 C6D20DS29D3 C6D20DS29D4 C6D20DS29E1 C6D20DS29E3 C6D20DS29E4 C6D20PF29012 C6D20PF29013 C6D20PF29022 C6D20PF29023 C6D20PF29032 C6D20PF29033 C6D20PF29042 C6D20PF29043 C6D20PF29132 C6D20PF29133 C6D20PF29142 C6D20PF29143 C6D22DS29A1 C6D22DS29A3 C6D22DS29A4 C6D22DS29B1 C6D22DS29B3 C6D22DS29B4 C6D22DS29C1 C6D22DS29C3 C6D22DS29C4 C6D22DS29D1 C6D22DS29D3 C6D22DS29D4 C6D22DS29E1 C6D22DS29E3 C6D22DS29E4 C6D22PF29012 C6D22PF29013 C6D22PF29022 C6D22PF29023 C6D22PF29032 C6D22PF29033 C6D22PF29042 C6D22PF29043 C6D22PF29132 C6D22PF29133 C6D22PF29142 C6D22PF29143 C6D25DS29A1 C6D25DS29A3 C6D25DS29A4 C6D25DS29B1 C6D25DS29B3 C6D25DS29B4 C6D25DS29C1 C6D25DS29C3 C6D25DS29C4 C6D25DS29D1 C6D25DS29D3 C6D25DS29D4 C6D25DS29E1 C6D25DS29E3 C6D25DS29E4 C6D25PF29012 C6D25PF29013 C6D25PF29022 C6D25PF29023 C6D25PF29032 C6D25PF29033 C6D25PF29042 C6D25PF29043 C6D25PF29132 C6D25PF29133 1-1437262-4 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 3-1437273-5 3-1437273-6 — — — 3-1437273-7 3-1437273-8 — — 3-1437273-9 4-1437273-0 — — — — — 1-1437262-8 — 1-1437262-9 — — — 2-1437262-0 — — — — — 4-1437273-1 — — — — — 4-1437273-2 — 4-1437273-3 — — — — — — — — — — — — — — — Page Number 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 196 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number C6D25PF29142 C6D25PF29143 C6D28DS29A1 C6D28DS29A3 C6D28DS29A4 C6D28DS29B1 C6D28DS29B3 C6D28DS29B4 C6D28DS29C1 C6D28DS29C3 C6D28DS29C4 C6D28DS29D1 C6D28DS29D3 C6D28DS29D4 C6D28DS29E1 C6D28DS29E3 C6D28DS29E4 C6D28PF29012 C6D28PF29013 C6D28PF29022 C6D28PF29023 C6D28PF29032 C6D28PF29033 C6D28PF29042 C6D28PF29043 C6D28PF29132 C6D28PF29133 C6D28PF29142 C6D28PF29143 C6D30DS29A1 C6D30DS29A3 C6D30DS29A4 C6D30DS29B1 C6D30DS29B3 C6D30DS29B4 C6D30DS29C1 C6D30DS29C3 C6D30DS29C4 C6D30DS29D1 C6D30DS29D3 C6D30DS29D4 C6D30DS29E1 C6D30DS29E3 C6D30DS29E4 C6D30PF29012 C6D30PF29013 C6D30PF29022 C6D30PF29023 C6D30PF29032 C6D30PF29033 C6D30PF29042 C6D30PF29043 C6D30PF29132 C6D30PF29133 C6D30PF29142 C6D30PF29143 C6D31DS29A1 C6D31DS29A3 C6D31DS29A4 C6D31DS29B1 C6D31DS29B3 C6D31DS29B4 C6D31DS29C1 C6D31DS29C3 C6D31DS29C4 C6D31DS29D1 C6D31DS29D3 C6D31DS29D4 C6D31DS29E1 C6D31DS29E3 C6D31DS29E4 C6D31PF29012 C6D31PF29013 C6D31PF29022 C6D31PF29023 C6D31PF29032 C6D31PF29033 C6D31PF29042 C6D31PF29043 C6D31PF29132 C6D31PF29133 C6D31PF29142 C6D31PF29143 C6D35DS29A1 C6D35DS29A3 C6D35DS29A4 C6D35DS29B1 C6D35DS29B3 Tyco Part Number — — — — — — — — 4-1437273-4 4-1437273-6 — 4-1437273-7 — — — — — — 2-1437262-4 — 2-1437262-6 — 2-1437262-7 — 2-1437262-8 — — — — — — — — — — 4-1437273-8 4-1437273-9 — — 5-1437273-0 5-1437273-1 — — — — — — 2-1437262-9 — — — — — — — — 5-1437273-2 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Page Number 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 Acquired Part Number C6D35DS29B4 C6D35DS29C1 C6D35DS29C3 C6D35DS29C4 C6D35DS29D1 C6D35DS29D3 C6D35DS29D4 C6D35DS29E1 C6D35DS29E3 C6D35DS29E4 C6D35PF29012 C6D35PF29013 C6D35PF29022 C6D35PF29023 C6D35PF29032 C6D35PF29033 C6D35PF29042 C6D35PF29043 C6D35PF29132 C6D35PF29133 C6D35PF29142 C6D35PF29143 C6D36DS29A1 C6D36DS29A3 C6D36DS29A4 C6D36DS29B1 C6D36DS29B3 C6D36DS29B4 C6D36DS29C1 C6D36DS29C3 C6D36DS29C4 C6D36DS29D1 C6D36DS29D3 C6D36DS29D4 C6D36DS29E1 C6D36DS29E3 C6D36DS29E4 C6D36PF29012 C6D36PF29013 C6D36PF29022 C6D36PF29023 C6D36PF29032 C6D36PF29033 C6D36PF29042 C6D36PF29043 C6D36PF29132 C6D36PF29133 C6D36PF29142 C6D36PF29143 C6D40DS29A1 C6D40DS29A3 C6D40DS29A4 C6D40DS29B1 C6D40DS29B3 C6D40DS29B4 C6D40DS29C1 C6D40DS29C3 C6D40DS29C4 C6D40DS29D1 C6D40DS29D3 C6D40DS29D4 C6D40DS29E1 C6D40DS29E3 C6D40DS29E4 C6D40PF29012 C6D40PF29013 C6D40PF29022 C6D40PF29023 C6D40PF29032 C6D40PF29033 C6D40PF29042 C6D40PF29043 C6D40PF29132 C6D40PF29133 C6D40PF29142 C6D40PF29143 C6D43DS29A1 C6D43DS29A3 C6D43DS29A4 C6D43DS29B1 C6D43DS29B3 C6D43DS29B4 C6D43DS29C1 C6D43DS29C3 C6D43DS29C4 C6D43DS29D1 C6D43DS29D3 C6D43DS29D4 Tyco Part Number Page Number — — — — — — — — — — — — — — — — — — — — — — — 5-1437273-3 — — — — 5-1437273-4 3-1437264-3 — 5-1437273-5 — 5-1437273-6 — — 5-1437273-7 — 3-1437262-3 — 3-1437262-4 — — — — — — — — — — — — 5-1437273-8 — — — — — — — — — — — — — — — — — — — — — — 5-1437273-9 — 6-1437273-0 6-1437273-1 — — 6-1437273-2 6-1437273-4 — — 6-1437273-6 — 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 Acquired Part Number Tyco Part Number C6D43DS29E1 C6D43DS29E3 C6D43DS29E4 C6D43PF29012 C6D43PF29013 C6D43PF29022 C6D43PF29023 C6D43PF29032 C6D43PF29033 C6D43PF29042 C6D43PF29043 C6D43PF29132 C6D43PF29133 C6D43PF29142 C6D43PF29143 C6D50DS29A1 C6D50DS29A3 C6D50DS29A4 C6D50DS29B1 C6D50DS29B3 C6D50DS29B4 C6D50DS29C1 C6D50DS29C3 C6D50DS29C4 C6D50DS29D1 C6D50DS29D3 C6D50DS29D4 C6D50DS29E1 C6D50DS29E3 C6D50DS29E4 C7D06DS29A1 C7D06DS29A3 C7D06DS29A4 C7D06DS29B1 C7D06DS29B3 C7D06DS29B4 C7D06DS29C1 C7D06DS29C3 C7D06DS29C4 C7D06DS29D1 C7D06DS29D3 C7D06DS29D4 C7D06DS29E1 C7D06DS29E3 C7D06DS29E4 C7D06PF29012 C7D06PF29013 C7D06PF29022 C7D06PF29023 C7D06PF29032 C7D06PF29033 C7D06PF29042 C7D06PF29043 C7D06PF29132 C7D06PF29133 C7D06PF29142 C7D06PF29143 C7D10DS29A1 C7D10DS29A3 C7D10DS29A4 C7D10DS29B1 C7D10DS29B3 C7D10DS29B4 C7D10DS29C1 C7D10DS29C3 C7D10DS29C4 C7D10DS29D1 C7D10DS29D3 C7D10DS29D4 C7D10DS29E1 C7D10DS29E3 C7D10DS29E4 C7D10PF29012 C7D10PF29013 C7D10PF29022 C7D10PF29023 C7D10PF29032 C7D10PF29033 C7D10PF29042 C7D10PF29043 C7D10PF29132 C7D10PF29133 C7D10PF29142 C7D10PF29143 C7D12PF29012 C7D12PF29013 C7D12PF29022 C7D12PF29023 — — — — 3-1437262-6 3-1437262-8 3-1437262-9 — — — 4-1437262-0 — — — — — — — — — — — — — — — — — — — — — — — — — 0-1437274-3 — — — — — — — — — — — 0-1437263-7 — — — 0-1437263-8 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Page Number 39 39 40 148 148 146 146 146 146 148 148 148 148 146 146 39 39 40 39 39 40 39 39 40 39 39 40 39 39 40 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 144 144 142 142 197 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number C7D12PF29032 C7D12PF29033 C7D12PF29042 C7D12PF29043 C7D12PF29132 C7D12PF29133 C7D12PF29142 C7D12PF29143 C7D15DS29A1 C7D15DS29A3 C7D15DS29A4 C7D15DS29B1 C7D15DS29B3 C7D15DS29B4 C7D15DS29C1 C7D15DS29C3 C7D15DS29C4 C7D15DS29D1 C7D15DS29D3 C7D15DS29D4 C7D15DS29E1 C7D15DS29E3 C7D15DS29E4 C7D15PF29012 C7D15PF29013 C7D15PF29022 C7D15PF29023 C7D15PF29032 C7D15PF29033 C7D15PF29042 C7D15PF29043 C7D15PF29132 C7D15PF29133 C7D15PF29142 C7D15PF29143 C7D18DS29A1 C7D18DS29A3 C7D18DS29A4 C7D18DS29B1 C7D18DS29B3 C7D18DS29B4 C7D18DS29C1 C7D18DS29C3 C7D18DS29C4 C7D18DS29D1 C7D18DS29D3 C7D18DS29D4 C7D18DS29E1 C7D18DS29E3 C7D18DS29E4 C7D18PF29012 C7D18PF29013 C7D18PF29022 C7D18PF29023 C7D18PF29032 C7D18PF29033 C7D18PF29042 C7D18PF29043 C7D18PF29132 C7D18PF29133 C7D18PF29142 C7D18PF29143 C7D20PF29012 C7D20PF29013 C7D20PF29022 C7D20PF29023 C7D20PF29032 C7D20PF29033 C7D20PF29042 C7D20PF29043 C7D20PF29132 C7D20PF29133 C7D20PF29142 C7D20PF29143 C7D22DS29A1 C7D22DS29A3 C7D22DS29A4 C7D22DS29B1 C7D22DS29B3 C7D22DS29B4 C7D22DS29C1 C7D22DS29C3 C7D22DS29C4 C7D22DS29D1 C7D22DS29D3 C7D22DS29D4 C7D22DS29E1 C7D22DS29E3 Tyco Part Number — — — — — — — — — — — — — — 0-1437274-5 0-1437274-7 — — — — — — — — — — — — — — — — — — — — — — — — 0-1437274-8 — — — — — — — 1-1437263-4 1-1437263-5 1-1437263-6 1-1437263-7 — — — 1-1437263-8 — — — — 1-1437263-9 2-1437263-0 — 2-1437263-1 — — — — — — — — — — — — — — 0-1437274-9 — — — 1-1437274-0 — — — Page Number 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 Acquired Part Number C7D22DS29E4 C7D22PF29012 C7D22PF29013 C7D22PF29022 C7D22PF29023 C7D22PF29032 C7D22PF29033 C7D22PF29042 C7D22PF29043 C7D22PF29132 C7D22PF29133 C7D22PF29142 C7D22PF29143 C7D25DS29A1 C7D25DS29A3 C7D25DS29A4 C7D25DS29B1 C7D25DS29B3 C7D25DS29B4 C7D25DS29C1 C7D25DS29C3 C7D25DS29C4 C7D25DS29D1 C7D25DS29D3 C7D25DS29D4 C7D25DS29E1 C7D25DS29E3 C7D25DS29E4 C7D25PF29012 C7D25PF29013 C7D25PF29022 C7D25PF29023 C7D25PF29032 C7D25PF29033 C7D25PF29042 C7D25PF29043 C7D25PF29132 C7D25PF29133 C7D25PF29142 C7D25PF29143 C7D28DS29A1 C7D28DS29A3 C7D28DS29A4 C7D28DS29B1 C7D28DS29B3 C7D28DS29B4 C7D28DS29C1 C7D28DS29C3 C7D28DS29C4 C7D28DS29D1 C7D28DS29D3 C7D28DS29D4 C7D28DS29E1 C7D28DS29E3 C7D28DS29E4 C7D28PF29012 C7D28PF29013 C7D28PF29022 C7D28PF29023 C7D28PF29032 C7D28PF29033 C7D28PF29042 C7D28PF29043 C7D28PF29132 C7D28PF29133 C7D28PF29142 C7D28PF29143 C7D30DS29A1 C7D30DS29A3 C7D30DS29A4 C7D30DS29B1 C7D30DS29B3 C7D30DS29B4 C7D30DS29C1 C7D30DS29C3 C7D30DS29C4 C7D30DS29D1 C7D30DS29D3 C7D30DS29D4 C7D30DS29E1 C7D30DS29E3 C7D30DS29E4 C7D30PF29012 C7D30PF29013 C7D30PF29022 C7D30PF29023 C7D30PF29032 C7D30PF29033 Tyco Part Number Page Number — — 2-1437263-3 — 2-1437263-4 — — — — — — — — — — — — — — 1-1437274-1 — — — — — — — — — — — — — — — — — — — — 1-1437274-3 1-1437274-4 — — 1-1437274-6 — 1-1437274-7 1-1437274-8 — 1-1437274-9 2-1437274-0 — — 2-1437274-2 — 2-1437263-7 2-1437263-8 — 2-1437263-9 2-1437274-3 — — — — — — — — 2-1437274-4 — — — — — 2-1437274-5 2-1437274-6 — — — — — — — 3-1437263-1 — 3-1437263-2 2-1437274-7 — 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 Acquired Part Number Tyco Part Number C7D30PF29042 C7D30PF29043 C7D30PF29132 C7D30PF29133 C7D30PF29142 C7D30PF29143 C7D31DS29A1 C7D31DS29A3 C7D31DS29A4 C7D31DS29B1 C7D31DS29B3 C7D31DS29B4 C7D31DS29C1 C7D31DS29C3 C7D31DS29C4 C7D31DS29D1 C7D31DS29D3 C7D31DS29D4 C7D31DS29E1 C7D31DS29E3 C7D31DS29E4 C7D31PF29012 C7D31PF29013 C7D31PF29022 C7D31PF29023 C7D31PF29032 C7D31PF29033 C7D31PF29042 C7D31PF29043 C7D31PF29132 C7D31PF29133 C7D31PF29142 C7D31PF29143 C7D35DS29A1 C7D35DS29A3 C7D35DS29A4 C7D35DS29B1 C7D35DS29B3 C7D35DS29B4 C7D35DS29C1 C7D35DS29C3 C7D35DS29C4 C7D35DS29D1 C7D35DS29D3 C7D35DS29D4 C7D35DS29E1 C7D35DS29E3 C7D35DS29E4 C7D35PF29012 C7D35PF29013 C7D35PF29022 C7D35PF29023 C7D35PF29032 C7D35PF29033 C7D35PF29042 C7D35PF29043 C7D35PF29132 C7D35PF29133 C7D35PF29142 C7D35PF29143 C7D36DS29A1 C7D36DS29A3 C7D36DS29A4 C7D36DS29B1 C7D36DS29B3 C7D36DS29B4 C7D36DS29C1 C7D36DS29C3 C7D36DS29C4 C7D36DS29D1 C7D36DS29D3 C7D36DS29D4 C7D36DS29E1 C7D36DS29E3 C7D36DS29E4 C7D36PF29012 C7D36PF29013 C7D36PF29022 C7D36PF29023 C7D36PF29032 C7D36PF29033 C7D36PF29042 C7D36PF29043 C7D36PF29132 C7D36PF29133 C7D36PF29142 C7D36PF29143 C7D40DS29A1 — 3-1437263-3 — — — — — 2-1437274-8 — — — — — 2-1437274-9 — — 3-1437274-0 — — — — — — — — — — — — — — — — — — — — — — 3-1437274-1 — — — — — — — — 3-1437263-9 4-1437263-0 — — — — — — — — — — — — — — — — 3-1437274-2 3-1437274-3 — — 3-1437274-4 — — — — 4-1437263-1 4-1437263-2 — — — 4-1437263-3 — — — — — — — Page Number 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 198 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number C7D40DS29A3 C7D40DS29A4 C7D40DS29B1 C7D40DS29B3 C7D40DS29B4 C7D40DS29C1 C7D40DS29C3 C7D40DS29C4 C7D40DS29D1 C7D40DS29D3 C7D40DS29D4 C7D40DS29E1 C7D40DS29E3 C7D40DS29E4 C7D40PF29012 C7D40PF29013 C7D40PF29022 C7D40PF29023 C7D40PF29032 C7D40PF29033 C7D40PF29042 C7D40PF29043 C7D40PF29132 C7D40PF29133 C7D40PF29142 C7D40PF29143 C7D43DS29A1 C7D43DS29A3 C7D43DS29A4 C7D43DS29B1 C7D43DS29B3 C7D43DS29B4 C7D43DS29C1 C7D43DS29C3 C7D43DS29C4 C7D43DS29D1 C7D43DS29D3 C7D43DS29D4 C7D43DS29E1 C7D43DS29E3 C7D43DS29E4 C7D43PF29012 C7D43PF29013 C7D43PF29022 C7D43PF29023 C7D43PF29032 C7D43PF29033 C7D43PF29042 C7D43PF29043 C7D43PF29132 C7D43PF29133 C7D43PF29142 C7D43PF29143 C7D50DS29A1 C7D50DS29A3 C7D50DS29A4 C7D50DS29B1 C7D50DS29B3 C7D50DS29B4 C7D50DS29C1 C7D50DS29C3 C7D50DS29C4 C7D50DS29D1 C7D50DS29D3 C7D50DS29D4 C7D50DS29E1 C7D50DS29E3 C7D50DS29E4 C7D50PF29012 C7D50PF29013 C7D50PF29022 C7D50PF29023 C7D50PF29032 C7D50PF29033 C7D50PF29042 C7D50PF29043 C7D50PF29132 C7D50PF29133 C7D50PF29142 C7D50PF29143 C8D06DS29A1 C8D06DS29A2 C8D06DS29A3 C8D06DS29B1 C8D06DS29B2 C8D06DS29B3 C8D06DS29C1 C8D06DS29C2 Tyco Part Number — — — — — 3-1437274-6 3-1437274-7 — — 3-1437274-8 — — — — 4-1437263-4 4-1437263-5 — 4-1437263-6 4-1437263-7 — — 4-1437263-8 — — — — — — — — — — 3-1437274-9 4-1437274-0 — — — 4-1437274-1 — — — — 5-1437263-0 — — — — — — — — — — — 4-1437274-3 — — 5-1437263-1 — 4-1437274-4 4-1437274-5 4-1437274-6 — 4-1437274-8 — 5-1437274-0 — — — 5-1437263-2 — — — 5-1437263-3 — 5-1437263-4 — — — 5-1437263-7 — — — — — — 2-1437275-9 3-1437275-0 Page Number 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 36 36 37 36 36 37 36 36 37 36 36 37 36 36 37 144 144 142 142 142 142 144 144 144 144 142 142 31 31 32 31 31 32 31 31 Acquired Part Number C8D06DS29C3 C8D06DS29D1 C8D06DS29D2 C8D06DS29D3 C8D06DS29E1 C8D06DS29E2 C8D06DS29E3 C8D06PF29012 C8D06PF29013 C8D06PF29022 C8D06PF29023 C8D06PF29032 C8D06PF29033 C8D06PF29042 C8D06PF29043 C8D06PF29132 C8D06PF29133 C8D06PF29142 C8D06PF29143 C8D10DS29A1 C8D10DS29A2 C8D10DS29A3 C8D10DS29B1 C8D10DS29B2 C8D10DS29B3 C8D10DS29C1 C8D10DS29C2 C8D10DS29C3 C8D10DS29D1 C8D10DS29D2 C8D10DS29D3 C8D10DS29E1 C8D10DS29E2 C8D10DS29E3 C8D10PF29012 C8D10PF29013 C8D10PF29022 C8D10PF29023 C8D10PF29032 C8D10PF29033 C8D10PF29042 C8D10PF29043 C8D10PF29132 C8D10PF29133 C8D10PF29142 C8D10PF29143 C8D12DS29A1 C8D12DS29A2 C8D12DS29A3 C8D12DS29B1 C8D12DS29B2 C8D12DS29B3 C8D12DS29C1 C8D12DS29C2 C8D12DS29C3 C8D12DS29D1 C8D12DS29D2 C8D12DS29D3 C8D12DS29E1 C8D12DS29E2 C8D12DS29E3 C8D12PF29012 C8D12PF29013 C8D12PF29022 C8D12PF29023 C8D12PF29032 C8D12PF29033 C8D12PF29042 C8D12PF29043 C8D12PF29132 C8D12PF29133 C8D12PF29142 C8D12PF29143 C8D15DS29A1 C8D15DS29A2 C8D15DS29A3 C8D15DS29B1 C8D15DS29B2 C8D15DS29B3 C8D15DS29C1 C8D15DS29C2 C8D15DS29C3 C8D15DS29D1 C8D15DS29D2 C8D15DS29D3 C8D15DS29E1 C8D15DS29E2 C8D15DS29E3 Tyco Part Number Page Number 3-1437275-1 — — — 3-1437275-2 — — — 1-1437260-4 — — — — — 1-1437260-5 — — — — — — 3-1437275-5 — — — 3-1437275-6 3-1437275-8 3-1437275-9 4-1437275-0 — 4-1437275-1 — — — — 2-1437260-0 — 2-1437260-2 — — — 2-1437260-3 — — — — — — — — — — 4-1437275-5 — 4-1437275-7 4-1437275-8 — — 5-1437274-1 — — — 2-1437260-4 — 2-1437260-5 — — — 2-1437260-6 — — — — — — — — — 5-1437275-1 5-1437275-2 — 5-1437275-4 5-1437275-5 5-1437275-6 — — — — 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 Acquired Part Number Tyco Part Number C8D15PF29012 C8D15PF29013 C8D15PF29022 C8D15PF29023 C8D15PF29032 C8D15PF29033 C8D15PF29042 C8D15PF29043 C8D15PF29132 C8D15PF29133 C8D15PF29142 C8D15PF29143 C8D18DS29A1 C8D18DS29A2 C8D18DS29A3 C8D18DS29B1 C8D18DS29B2 C8D18DS29B3 C8D18DS29C1 C8D18DS29C2 C8D18DS29C3 C8D18DS29D1 C8D18DS29D2 C8D18DS29D3 C8D18DS29E1 C8D18DS29E2 C8D18DS29E3 C8D20DS29A1 C8D20DS29A2 C8D20DS29A3 C8D20DS29B1 C8D20DS29B2 C8D20DS29B3 C8D20DS29C1 C8D20DS29C2 C8D20DS29C3 C8D20DS29D1 C8D20DS29D2 C8D20DS29D3 C8D20DS29E1 C8D20DS29E2 C8D20DS29E3 C8D20PF29012 C8D20PF29013 C8D20PF29022 C8D20PF29023 C8D20PF29032 C8D20PF29033 C8D20PF29042 C8D20PF29043 C8D20PF29132 C8D20PF29133 C8D20PF29142 C8D20PF29143 C8D22DS29A1 C8D22DS29A2 C8D22DS29A3 C8D22DS29B1 C8D22DS29B2 C8D22DS29B3 C8D22DS29C1 C8D22DS29C2 C8D22DS29C3 C8D22DS29D1 C8D22DS29D2 C8D22DS29D3 C8D22DS29E1 C8D22DS29E2 C8D22DS29E3 C8D22PF29012 C8D22PF29013 C8D22PF29022 C8D22PF29023 C8D22PF29032 C8D22PF29033 C8D22PF29042 C8D22PF29043 C8D22PF29132 C8D22PF29133 C8D22PF29142 C8D22PF29143 C8D25DS29A1 C8D25DS29A2 C8D25DS29A3 C8D25DS29B1 C8D25DS29B2 C8D25DS29B3 C8D25DS29C1 — 2-1437260-7 — 2-1437260-9 — — — 3-1437260-0 — — — — — — — — — — 5-1437275-9 — 6-1437275-1 6-1437275-2 — 6-1437275-3 6-1437275-4 — — — — — — — — 6-1437275-6 — 6-1437275-8 6-1437275-9 — 7-1437275-0 — — — — — — 3-1437260-5 — — — 3-1437260-6 — — — — 7-1437275-1 — 7-1437275-2 7-1437275-3 — — 7-1437275-4 — 7-1437275-6 7-1437275-7 — — — — — — 3-1437260-8 — 4-1437260-0 — — — 4-1437260-1 — — — — 7-1437275-8 — 7-1437275-9 — — — 8-1437275-0 Page Number 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 199 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number C8D25DS29C2 C8D25DS29C3 C8D25DS29D1 C8D25DS29D2 C8D25DS29D3 C8D25DS29E1 C8D25DS29E2 C8D25DS29E3 C8D25PF29012 C8D25PF29013 C8D25PF29022 C8D25PF29023 C8D25PF29032 C8D25PF29033 C8D25PF29042 C8D25PF29043 C8D25PF29132 C8D25PF29133 C8D25PF29142 C8D25PF29143 C8D28DS29A1 C8D28DS29A2 C8D28DS29A3 C8D28DS29B1 C8D28DS29B2 C8D28DS29B3 C8D28DS29C1 C8D28DS29C2 C8D28DS29C3 C8D28DS29D1 C8D28DS29D2 C8D28DS29D3 C8D28DS29E1 C8D28DS29E2 C8D28DS29E3 C8D28PF29012 C8D28PF29013 C8D28PF29022 C8D28PF29023 C8D28PF29032 C8D28PF29033 C8D28PF29042 C8D28PF29043 C8D28PF29132 C8D28PF29133 C8D28PF29142 C8D28PF29143 C8D30DS29A1 C8D30DS29A2 C8D30DS29A3 C8D30DS29B1 C8D30DS29B2 C8D30DS29B3 C8D30DS29C1 C8D30DS29C2 C8D30DS29C3 C8D30DS29D1 C8D30DS29D2 C8D30DS29D3 C8D30DS29E1 C8D30DS29E2 C8D30DS29E3 C8D30PF29012 C8D30PF29013 C8D30PF29022 C8D30PF29023 C8D30PF29032 C8D30PF29033 C8D30PF29042 C8D30PF29043 C8D30PF29132 C8D30PF29133 C8D30PF29142 C8D30PF29143 C8D31DS29A1 C8D31DS29A2 C8D31DS29A3 C8D31DS29B1 C8D31DS29B2 C8D31DS29B3 C8D31DS29C1 C8D31DS29C2 C8D31DS29C3 C8D31DS29D1 C8D31DS29D2 C8D31DS29D3 C8D31DS29E1 C8D31DS29E2 Tyco Part Number — 8-1437275-2 8-1437275-3 — 8-1437275-4 — — — — 4-1437260-5 — 4-1437260-8 — 4-1437260-9 — — — — — — — — — — — — 8-1437275-5 — 8-1437275-8 8-1437275-9 — 9-1437275-0 — — — 9-1437275-1 — — 5-1437260-5 — — — — — — — — — — — — — — 9-1437275-3 — 9-1437275-5 9-1437275-6 — 9-1437275-7 9-1437275-8 — 9-1437275-9 — 5-1437260-6 — 5-1437260-8 — — — 6-1437260-1 — 6-1437260-4 — — — — 0-1437276-2 — — — 0-1437276-3 0-1437276-5 0-1437276-6 0-1437276-8 — 0-1437276-9 — — Page Number 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 Acquired Part Number C8D31DS29E3 C8D31PF29012 C8D31PF29013 C8D31PF29022 C8D31PF29023 C8D31PF29032 C8D31PF29033 C8D31PF29042 C8D31PF29043 C8D31PF29132 C8D31PF29133 C8D31PF29142 C8D31PF29143 C8D35DS29A1 C8D35DS29A2 C8D35DS29A3 C8D35DS29B1 C8D35DS29B2 C8D35DS29B3 C8D35DS29C1 C8D35DS29C2 C8D35DS29C3 C8D35DS29D1 C8D35DS29D2 C8D35DS29D3 C8D35DS29E1 C8D35DS29E2 C8D35DS29E3 C8D35PF29012 C8D35PF29013 C8D35PF29022 C8D35PF29023 C8D35PF29032 C8D35PF29033 C8D35PF29042 C8D35PF29043 C8D35PF29132 C8D35PF29133 C8D35PF29142 C8D35PF29143 C8D36DS29A1 C8D36DS29A2 C8D36DS29A3 C8D36DS29B1 C8D36DS29B2 C8D36DS29B3 C8D36DS29C1 C8D36DS29C2 C8D36DS29C3 C8D36DS29D1 C8D36DS29D2 C8D36DS29D3 C8D36DS29E1 C8D36DS29E2 C8D36DS29E3 C8D36PF29012 C8D36PF29013 C8D36PF29022 C8D36PF29023 C8D36PF29032 C8D36PF29033 C8D36PF29042 C8D36PF29043 C8D36PF29132 C8D36PF29133 C8D36PF29142 C8D36PF29143 C8D40DS29A1 C8D40DS29A2 C8D40DS29A3 C8D40DS29B1 C8D40DS29B2 C8D40DS29B3 C8D40DS29C1 C8D40DS29C2 C8D40DS29C3 C8D40DS29D1 C8D40DS29D2 C8D40DS29D3 C8D40DS29E1 C8D40DS29E2 C8D40DS29E3 C8D40PF29012 C8D40PF29013 C8D40PF29022 C8D40PF29023 C8D40PF29032 C8D40PF29033 Tyco Part Number Page Number — — 6-1437260-5 — 6-1437260-6 — — — 6-1437260-7 6-1437260-8 6-1437260-9 — — 1-1437276-0 — 1-1437276-1 — — — — — 1-1437276-3 — — — — — 1-1437276-4 — — — 7-1437260-3 — — — — — — — — — — 1-1437276-5 — — — 1-1437276-6 1-1437276-8 1-1437276-9 2-1437276-0 2-1437276-1 2-1437276-2 — — 2-1437276-3 — 7-1437260-7 7-1437260-9 8-1437260-0 — 8-1437260-1 — 8-1437260-2 — — — — 2-1437276-5 — 2-1437276-6 — — — 2-1437276-7 — 2-1437276-9 3-1437276-0 — 3-1437276-1 — — — — — — 8-1437260-4 — — 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 Acquired Part Number Tyco Part Number C8D40PF29042 C8D40PF29043 C8D40PF29132 C8D40PF29133 C8D40PF29142 C8D40PF29143 C8D43DS29A1 C8D43DS29A2 C8D43DS29A3 C8D43DS29B1 C8D43DS29B2 C8D43DS29B3 C8D43DS29C1 C8D43DS29C2 C8D43DS29C3 C8D43DS29D1 C8D43DS29D2 C8D43DS29D3 C8D43DS29E1 C8D43DS29E2 C8D43DS29E3 C8D43PF29012 C8D43PF29013 C8D43PF29022 C8D43PF29023 C8D43PF29032 C8D43PF29033 C8D43PF29042 C8D43PF29043 C8D43PF29132 C8D43PF29133 C8D43PF29142 C8D43PF29143 C8D50DS29A1 C8D50DS29A2 C8D50DS29A3 C8D50DS29B1 C8D50DS29B2 C8D50DS29B3 C8D50DS29C1 C8D50DS29C2 C8D50DS29C3 C8D50DS29D1 C8D50DS29D2 C8D50DS29D3 C8D50DS29E1 C8D50DS29E2 C8D50DS29E3 C8D50PF29012 C8D50PF29013 C8D50PF29022 C8D50PF29023 C8D50PF29032 C8D50PF29033 C8D50PF29042 C8D50PF29043 C8D50PF29132 C8D50PF29133 C8D50PF29142 C8D50PF29143 C8D52DS29C1M191 C8D52DS29C1M195 C8D60DS29A1 C8D60DS29A2 C8D60DS29A3 C8D60DS29B1 C8D60DS29B2 C8D60DS29B3 C8D60DS29C1 C8D60DS29C2 C8D60DS29C3 C8D60DS29D1 C8D60DS29D2 C8D60DS29D3 C8D60DS29E1 C8D60DS29E2 C8D60DS29E3 C8D60PF29012 C8D60PF29013 C8D60PF29022 C8D60PF29023 C8D60PF29032 C8D60PF29033 C8D60PF29042 C8D60PF29043 C8D60PF29132 C8D60PF29133 C8D60PF29142 — 8-1437260-6 — — — — — — — — — — 3-1437276-2 — 3-1437276-3 — — 3-1437276-4 3-1437276-5 — — 8-1437260-9 9-1437260-0 9-1437260-2 9-1437260-3 — — — — — — — — 3-1437276-8 — 3-1437276-9 — — — 4-1437276-0 — 4-1437276-2 4-1437276-3 — — — — — — 9-1437260-9 — 0-1437261-2 — 0-1437261-5 — 0-1437261-6 — — — — 4-1437276-6 4-1437276-7 5-1437276-1 — 5-1437276-2 — — 5-1437276-3 5-1437276-4 — — 5-1437276-7 — — — — — — 5-1437276-8 — 1-1437261-1 — — — — — — — Page Number 140 140 140 140 138 138 31 31 32 31 31 32 31 31 32 31 31 32 31 31 32 140 140 138 138 138 138 140 140 140 140 138 138 31 32 32 31 32 32 31 32 32 31 32 32 31 32 32 140 140 138 138 138 138 140 140 140 140 138 138 29 29 31 32 32 31 32 32 31 32 32 31 32 32 31 32 32 140 140 138 138 138 138 140 140 140 140 138 200 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Part Number Cross Reference—Acquired Part Number to Tyco Part Number Acquired Part Number Tyco Part Number C8D60PF29143 C9D020PF60048 C9D030PF60048 C9D040PF60048 C9D050PF60048 C9D060PF60048 W8D18DS29063 W8D18DS29093 W8D18PF29012 W8D18PF29013 W8D18PF29042 W8D18PF29043 W8D18PF29062 W8D18PF29063 W8D18PF29092 W8D18PF29093 W8D20DS29063 W8D20DS29093 W8D20PF29012 W8D20PF29013 W8D20PF29042 W8D20PF29043 W8D20PF29062 W8D20PF29063 W8D20PF29092 W8D20PF29093 W8D22DS29063 W8D22DS29093 W8D22PF29012 W8D22PF29013 W8D22PF29042 W8D22PF29043 W8D22PF29062 W8D22PF29063 W8D22PF29092 W8D22PF29093 W8D25DS29063 W8D25DS29093 W8D25PF29012 W8D25PF29013 W8D25PF29042 W8D25PF29043 W8D25PF29062 W8D25PF29063 W8D25PF29092 W8D25PF29093 W8D28DS29063 W8D28DS29093 W8D28PF29012 W8D28PF29013 W8D28PF29042 W8D28PF29043 W8D28PF29062 W8D28PF29063 W8D28PF29092 W8D28PF29093 W8D30DS29063 W8D30DS29093 W8D30PF29012 W8D30PF29013 W8D30PF29042 W8D30PF29043 W8D30PF29062 W8D30PF29063 W8D30PF29092 W8D30PF29093 W8D35DS29063 W8D35DS29093 W8D35PF29012 W8D35PF29013 W8D35PF29042 W8D35PF29043 W8D35PF29062 W8D35PF29063 W8D35PF29092 W8D35PF29093 W8D36DS29063 W8D36DS29093 W8D36PF29012 W8D36PF29013 W8D36PF29042 W8D36PF29043 W8D36PF29062 W8D36PF29063 W8D36PF29092 W8D36PF29093 W8D40DS29063 W8D40DS29093 — 3-1437264-4 3-1437264-5 — — 3-1437264-6 — — — — — — — 1-1437265-0 — — — — — — — — — — — — — — — — — 1-1437265-2 — — — — — — — 1-1437265-3 — — — 1-1437265-4 — 1-1437265-5 — — — 1-1437265-6 — — — — — 1-1437265-7 — — — 2-1437265-0 — 2-1437265-1 — — — — — — — 2-1437265-3 — — — 2-1437265-5 — — — — — 2-1437265-6 — 2-1437265-7 — — — 2-1437265-8 — — Page Number 138 129 129 129 129 129 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 Acquired Part Number W8D40PF29012 W8D40PF29013 W8D40PF29042 W8D40PF29043 W8D40PF29062 W8D40PF29063 W8D40PF29092 W8D40PF29093 W8D43DS29063 W8D43DS29093 W8D43PF29012 W8D43PF29013 W8D43PF29042 W8D43PF29043 W8D43PF29062 W8D43PF29063 W8D43PF29092 W8D43PF29093 W8D45DS29063 W8D45DS29093 W8D45PF29012 W8D45PF29013 W8D45PF29042 W8D45PF29043 W8D45PF29062 W8D45PF29063 W8D45PF29092 W8D45PF29093 W8D50DS29063 W8D50DS29093 W8D50PF29012 W8D50PF29013 W8D50PF29042 W8D50PF29043 W8D50PF29062 W8D50PF29063 W8D50PF29092 W8D50PF29093 W8D60DS29063 W8D60DS29093 W8D60PF29012 W8D60PF29013 W8D60PF29042 W8D60PF29043 W8D60PF29062 W8D60PF29063 W8D60PF29092 W8D60PF29093 Tyco Part Number Page Number — 3-1437265-0 — — — — — — — — — — — — — — — — — — — — — — — — — — — — 3-1437265-4 3-1437265-5 — 3-1437265-6 3-1437265-7 — — — — — — 3-1437265-9 — — — — — — 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 34 34 134 134 134 134 136 136 136 136 201 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Card Edge Connectors Related Product Information For additional component solutions for Industrial Machinery, Instrumentation, Security, and related applications, request the following brochures: Brochure No. 889439 – Industrial Machinery Brochure No. 1307285 – Instrumentation Brochure No. 1308325 – Security These brochures list catalog sources for connectors, switches, terminal blocks, relays, timers, circuit breakers, and cable assemblies available from Tyco Electronics. 202 Catalog 1654080 Issued 7-03 www.tycoelectronics.com Dimensions are in millimeters and inches unless otherwise specified. Values in bold are imperial equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-5-729-0425 South America: 55-11-3611-1514 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-141-810-8967 Global Contacts Americas Argentina – Buenos Aires Phone: +54-11-4733-2200 Fax: +54-11-4733-2250 Brasil – São Paulo Phone: +55-11-3611-1311 Fax: +55-11-3611-0397 Canada – Markham Phone: +905-475-6222 Fax: +905-474-5520 Product Information Center: (Technical Support) Phone: +905-470-4425 Fax: +905-474-5525 Colombia – Bogota Phone: +57-1-240-9396 Fax: +57-1-660-0206 Mexico – Mexico City Phone: +52-55-5-729-0425 Fax: +52-55-5-398-1430 For Latin/South American Countries not shown Phone: +57-1-240-9396 Fax: +57-1-660-0206 United States – Harrisburg, PA Phone: +717-564-0100 Fax: +717-986-7575 Product Information Center: (Technical Support) Phone: +800-522-6752 Fax: +717-986-7575 Asia/ Pacific Australia – Sydney Phone: +61-2-9840-8200 Fax: +61-2-9899-5649 Product Information Center: (Technical Support) Phone: +61-2-9554-2600 Fax: +61-2-9502-2556 India – Bangalore Phone: +91-80-841-0200 Fax: +91-80-841-0210 Indonesia – Jakarta Phone: +6221-526-7852 Fax: +6221-526-7856 Japan – Kawasaki, Kanagawa Phone: +81-44-844-8079 Fax: +81-44-844-8733 Product Information Center: (Technical Support) Phone: +81-44-844-8013 Fax: +81-44-812-3200 Raychem Products Phone: +81-44-900-5102 Fax: +81-44-5025-5027 Korea – Seoul Phone: +82-2-3274-0535 Fax: +82-2-3274-0524/0531 Malaysia – Selangor Phone: +60-3-7053055 Fax: +60-3-7053066 New Zealand – Auckland Phone: +64-9-634-4580 Fax: +64-9-634-4586 Philippines – Makati City Phone: +632-867-8641 Fax: +632-867-8661 People’s Republic of China Hong Kong Phone: +852-2735-1628 Fax: +852-2735-0243 Shanghai Phone: Fax: +86-21-6485-0602 +86-21-6485-0728 Shunde Phone: Fax: +86-765-775-1368 +86-765-775-2823 Singapore – Singapore Phone: +65-482-0311 Fax: +65-482-1012 Raychem Products Phone: +65-486-6151 Fax: +65-654-5514 Taiwan – Taipei Phone: +886-2-2664-9977 Fax: +886-2-2664-9900 Thailand – Bangkok Phone: +66-2-955-0500 Fax: +66-2-955-0505 Vietnam – Ho Chi Minh City Phone: +84-8-8232-546/7 Fax: +84-8-8221-443 Europe/ Middle East/Africa Austria – Vienna Phone: +43-190-560-0 Fax: +43-190-560-1333 Belgium – Kessel-Lo Phone: +32-16-352-300 Fax: +32-16-352-352 Germany – Bensheim Phone: +49-6251-133-0 Fax: +49-6251-133-1600 Product Information Center: (Technical Support) Phone: +49-6251-133-1999 Fax: +49-6251-133-1988 Bulgaria – Sofia Phone: +359-2-971-2152 Fax: +359-2-971-2153 Germany – Langen Phone: +49-6103-709-0 Fax: +49-6103-709-1223 Czech Republic – Kurim Phone: +420-5-41-162-111 Fax: +420-5-41-162-223 Germany – Speyer Phone: +49-6232-30-0 Fax: +49-6232-30-2243 Denmark – Viby J Phone: +45-70-15-52-00 Fax: +45-86-29-51-33 Germany HTS Division – Neunkirchen Phone: +49-2247-305-0 Fax: +49-2247-305-122 Egypt – Cairo Phone: +20-2-417-76-47 Fax: +20-2-419-23-34 Estonia – Tallinn Phone: +372-65-05-474 Fax: +372-65-05-470 Finland – Helsinki Phone: +358-95-12-34-20 Fax: +358-95-12-34-250 France – Cergy-Pontoise Phone: +33-1-3420-8888 Fax: +33-1-3420-8600 Product Information Center: (Technical Support) Phone: +33-1-3420-8943 Fax: +33-1-3420-8623 France Tyco Electronics Export – St Ouen L’Aumone Phone: +33-1-3440-7200 Fax: +33-1-3440-7220 or +33-1-3440-7230 Great Britain – Stanmore Middlesex Phone: +44-181-954-2356 Fax: +44-181-954-6234 Product Information Center: (Technical Support) Freephone GB: 0800-267-666 Phone: +44-141 810 8967…69 Fax: +44-141 810 8971 Great Britain – Dorcan, Swindon Raychem Products Phone: +44-1793-528171 Fax: +44-1793-572516 Italy – Collegno (Torino) Phone: +39-011-4012-111 Fax: +39-011-4031-116 Lithuania – Vilnius Phone: +370-5-21-31-402 Fax: +370-5-21-31-403 Netherlands – ’s-Hertogenbosch Phone: +31-73-6246-246 Fax: +31-73-6212-365 Product Information Center: (Technical Support) Phone: +31-73-6246-999 Fax: +31-73-6246-998 Norway – Nesbru Phone: +47-66-77-88-99 Fax: +47-66-77-88-55 Poland – Warsaw Phone: +48-22-5490-888 Fax: +48-22-5490-880 Romania – Bucharest Phone: +40-1-311-3479+3596 Fax: +40-1-312-0574 Sweden – Upplands Väsby Phone: +46-8-50-72-50-00 Fax: +46-8-50-72-50-01 Switzerland – Steinach Phone: +41-71-447-0447 Fax: +41-71-447-0444 Turkey – Istanbul Phone: +90-212-281-8181…3 +90-212-282-5130/5430 Fax: +90-212-281-8184 Ukraine – Kiev Phone: +38-044-238-6908 Fax: +38-044-568-5740 Russia – Moscow Phone: +7-095-926-55-06…09 Fax: +7-095-926-55-05 Russia – St. Petersburg Phone: +7-812-325-30-83 Fax: +7-812-325-32-88 Greece – Athens Phone: +30-1-9370-396/397 Fax: +30-1-9370-655 Scotland – Dundee Madison Cable Products Phone: +44-1382-508080 Fax: +44-1382-505060 Hungary – Budapest Phone: +36-1-289-1000 Fax: +36-1-289-1010 Slovakia – Banská Bystrica Phone: +421-48-415-20-11/12 Fax: +421-48-415-20-13 Ireland – Dublin Phone: +353-1-820-3000 Fax: +353-1-820-9790 Slovenia – Ljubljana Phone: +386-1561-3270 Fax: +386-1561-3240 Israel – Yokneam Phone: +972-4-959-0508 Fax: +972-4-959-0506 Spain – Barcelona Phone: +34-93-291-0330 Fax: +34-93-201-7879 Product Information Center: (Technical Support): Phone: +34-93-291-0330 Fax: +34-93-200-3779 South Africa – Port Elizabeth Phone: +27-41-405-4500 Fax: +27-41-486-1314 203 1654080–7.5M–SK–CAD–7-03–0G3B Printed in U.S.A. Tyco Electronics Corporation www.tycoelectronics.com TYCO ELECTRONICS CORPORATION WWW.TYCOELECTRONICS.COM