CAP200AAANA

KILOVAC High Voltage DC Contactors KILOVAC CAP200 Series Contactor with 1 Form A (SPST-NO) Contacts Rated up to 500 Amps, 12-900 Vdc Product Facts Performance Data n Designed to be the smallest, lightest weight, lowest cost sealed contactor in the industry with its current rating n Built-in coil economizer — only 1.7W hold power @ 12VDC and it limits back EMF to 0V. (models requiring external economizer also available) n Optional auxiliary contact for easy monitoring of power contact position n Hermetically sealed — intrinsically safe, operates in explosive/harsh environments with no oxidation or contamination of coil or contacts, including long periods of nonoperation n Versatile coil and power connections n RoHS versions available Coil Operating Voltage (Valid Over Temperature Range) 9-36VDC 32-95VDC 48-95VDC Voltage (Will Operate) Voltage (Max.) 36VDC 95VDC 95VDC Pickup (Close) Voltage Max. 9VDC 32VDC 48VDC Hold Voltage (Min.) 7.5VDC 22VDC 34VDC Dropout (Open) Voltage (Min.) 6VDC 18VDC 27VDC Inrush Current (Max.) 3.8A 1.3A 0.7A 0.13A@12V, Holding Current (Avg.) 0.03A@48V 0.02A@72V 0.07A@24V Inrush Time (Max.) 130ms 130ms 130ms Ordering Information Typical Part Number 䊳 CAP200 A A A N A Series: CAP200 = 500 Amp, 12-900VDC Contactor Contact Form: A = Normally Open H = Normally Open with Aux. Contacts Coil Voltage: A = 9-36VDC (1 = requires external coil economizer) D = 32-95VDC (2 = requires external coil economizer) J = 48-95VDC (3 = requires external coil economizer) Contact Arrangement, Power Contacts — 1 Form A (SPST-NO) Rated Operating Voltage — 12 - 900 VDC Continuous (Carry) Current, Typical — 500 A @ 85°C, 400 mcm conductors Consult Factory for required conductors for higher currents Make/Break Current at Various Voltages 1 — See graph next page Break Current at 320VDC 1 — 2,000 A, 1 cycle 3 Contact Resistance, Typ. (@200A) — 0.2 mohms Load Life — See graph next page Mechanical Life — 1 million cycles Contact Arrangement, Auxiliary Contacts — 1 Form A (SPST-NO) Aux. Contact Current, Max. — 2A @ 30VDC / 3A @ 125VAC Aux. Contact Current, Min. — 100mA @ 8V Aux. Contact Resistance, Max. — 0.417 ohms @ 30VDC / .150 ohms @ 125VAC Dielectric Withstanding Voltage — 2,200 Vrms @ sea level Insulation Resistance @ 500VDC — 100 megohms 2 Shock, 11ms 1/2 Sine, Peak, Operating — 20 G Vibration, Sine, 80-2000Hz., Peak — 20 G Operating Temperature — -40°C to +85°C Weight, Nominal — .95 lb. (.43 kg) Notes: 1 Main power contacts 2 50 at end of life 3 Does not meet dielectric & IR after test, 1700 amp for unit with Aux. Contacts R = 28 Vdc with mechanical economizer Coil Wire Length: A = 15.3 in (390 mm) D = Coil connector on relay (requires option “E” or “X” in next step) Coil Terminal Connector: N = None E = 9-pin subminiature “D” plug mounted on contactor housing F = 9-pin subminiature “D” plug mounted on 15.3 in (390 mm) flying leads. X = Special configuration (consult factory) For factory-direct application assistance, dial 800-253-4560, ext. 2055, or 805-220-2055. Mounting & Power Terminals: A = Bottom Mount & Male 10mm x 8 Terminals 7–16 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com KILOVAC High Voltage DC Contactors KILOVAC CAP200 Series (Continued) Outline Dimensions M8 x 1.25 POWER TERMINALS (HARDWARE SUPPLIED): 2 X M8 WASHER, STAINLESS 2 X M8 LOCKWASHER – SPLIT RING, STAINLESS 2 X M8 x 1.25 NUT, STAINLESS TORQUE 80 TO 100 IN-LB (8.8 TO 11 NM) 1.05 ± .01 (26.67 ± .26) 2.29 ± .02 DIA (58.19 ± .51) A1 "+" POSITIVE TERMINAL A2 "–" NEGATIVE TERMINAL .225 ± .01DIA (5.72 ± .26) MOUNTING HARDWARE (NOT SUPPLIED): 2 X M5 BOLT 2 X M5 LOCKWASHER 2 X M5 NARROW WASHER TORQUE 15 TO 30 IN-LB (1.7 TO 3.3 NM) 1.65 ± .01 (42.0 ± .26) 2.688 ± .01 (68.28 ± .26) AUXILIARY CONTACT LEADS WHITE = AUXILIARY CONTACT (WHEN ORDERED) BLACK = – COIL RED = + COIL COIL LEADS SEE COIL WIRE LENGTH IN P/N 2.20 ± .025 (55.81 ± .63) 2.85 ± .025 (72.3 ± .63) STAINLESS 2.04 ± .02 DIA (51.94 ± .51) .55 ± .025 (14.04 ± .63) 2.05 ± .02 (52 ± .51) 2.58 ± .02 (65.6 ± .51) 3.17 ± .01 (80.48 ± .26) .5 ± .01 (12.6 ± .26) Estimated Make & Break Power Switching Ratings Make and Break Power Switching Region 650A Break Only Above 650A 100,000 10,000 900 VDC 120 C VD 100 400 VDC Estimated Life (Cycles) 28 VDC C VD DC VDC 0V 270 600 18 0 1,000 7 10 KILOVAC High Voltage DC Contactors 1 1 10 100 Load Current (A) 1,000 10,000 NOTES: 1) For resistive loads with 300µH maximum inductance. Consult factory for inductive loads. 2) Estimates based on extrapolated data. User is encouraged to confirm performance in application. 3) End of life when dielectric strength between terminals falls below 50 megohms @ 500VDC. 4) The maximum make current is 650A to avoid contact welding. For factory-direct application assistance, dial 800-253-4560, ext. 2055, or 805-220-2055. 7–17 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com