CBT25J47K

Carbon Composition Resistors Key Features Type CBT Series Solid Carbon Composition Designed for Pulse Withstand Low Cost, High Performance Two Sizes Available Supplied Ammo Pack in boxes of 2000 The CBT series of resistors is constructed utilising solid carbon composition, which is the traditional medium for absorbing high energy pulses, in cases of high inrush current. These resistors have evolved over many years to have excellent pulse withstand capabilities, whilst remaining very stable. These improved characteristics have been achieved by prudent selection of materials of optimum physical properties and by advances in the manufacturing process. Characteristics – Electrical Power @ 70°C Maximum Voltage Tolerance Selection Series Resistance values Ω Limiting Element Voltage Maximum Overload Voltage Insulation Resistance Operating Temperature CBT25 0.25W (~0 @ 125°C) 250V 5% 10% 10% 20% E24 E24 E12 E6 100K – 1 -91K 1 – 5M6 5M6 250v CBT50 0.5W (~0 @ 125°C) 350V 5% 10% 10% 20% E24 E24 E12 E6 1 – 91K 100K – 1 – 22M 22M 350v 500v 700v 1000M minimum -55 ~ +125 Climatic Category 55/125/56 Lower Category Temperature Upper Category Temperature Damp Heat Steady State Duration -55°C +125°C 56 Days Stability Class 10% 1773192 Rev D 03/2019 Limits For Change of Resistance For Long Term Tests For Short Term Tests Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change ±(10%+0.5Ω) ±(2%+0.1Ω) For Email, phone or live chat, go to: www.te.com/help Carbon Composition Resistors Derating At ambient temperatures in excess of 70°C the resistor shall be derated in accordance with the following curve: Rated Voltage D.C. or A.C. rms voltage calculated from the square root of the product of the rated resistance and the rated dissipation. Where the calculated rated voltage is higher than the limiting element voltage, the limiting element voltage must be applied. Dimensions 1773192 Rev D 03/2019 CBT25 L 6.3±0.7 CBT50 9.5 Dimensions in millimetres unless otherwise specified +0.8 -0.7 ØD 2.4±0.1 l 30±3 Ød 0.6±0.05 3.6±0.2 25±3 0.7 Dimensions Shown for reference purposes only. Specifications subject to change +0.07 -0.05 For Email, phone or live chat, go to: www.te.com/help Carbon Composition Resistors Performance Characteristics Test Item Condition of Test (JIS C 5201-1) Visual Examination Sub-clause 4.4.1 Checked by visual examination Dimension Sub-clause 4.4.2 Resistance Sub-clause 4.5 Voltage Proof Solderability Overload (mounted) Terminal strength Tensile Bending Torsion 1773192 Rev D 03/2019 Dimensions in millimetres unless otherwise specified Sub-clause 4.7 Method: V-Block Method Test Voltage: Alternating voltage with a peak value of 1.42 times the insulation voltage. Duration 60s ±5s Sub-clause 4.17 Without ageing Method 1 (solder bath method) Bath Temperature: 235°C±5°C Immersion time: 5s ±0.5s Immersion depth: A point within about 4mm from the resistor body. Sub-clause 4.13 The applied voltage shall be 2.5 times RCWV or 2 times limiting element voltage, whichever is lower. Duration: 5s Visual Examination Resistance test Sub-clause 4.16 Sub-clause 4.16.2 Force: 10N Duration: 10s ±1s Sub-clause 4.16.3 Method 1 Bending times: 2 times Bending force: 5N Sub-clause 4.16.4 Method A, Severity 2 (2 successive rotations of 180°) Dimensions Shown for reference purposes only. Specifications subject to change Performance Requirement As per 4.4.1 Marking shall be legible as checked visually As specified As specified Resistance value shall correspond to the rated resistance value taking into account the specified tolerance No breakdown or flashover Good tinning as evidenced by free flowing of the solder with wetting of the terminations No Visible Damage Legible Marking ΔR ±(2%+0.1Ω) No visible damage ΔR ±(2%+0.1Ω For Email, phone or live chat, go to: www.te.com/help Carbon Composition Resistors Resistance to soldering heat Rapid Temperature change Vibration Climatic sequence Dry Heat Damp Heat, cycle (12 + 12h cycle First Cycle Cold Low air pressure Damp heat, cycle (12 + 12h cycle) Remaining cycle D.C. load Endurance @ 70°C 1773192 Rev D 03/2019 Dimensions in millimetres unless otherwise specified Sub-clause 4.18 Method 1B Solder Temperature: CBT25: 300°C±10°C CBT50: 350°C±10°C Immersion time: 3.5s±0.5s Immersion depth: A point within 4.0±0.8mm from the resistor body. Sub-clause 4.19 Lower category temperature: 55°C Upper category temperature: 125°C Duration of exposure at each temperature: 30 min. Number of cycles: 5 Sub-Clause 4.22 Endurance by sweeping Frequency range: 10Hz – 500Hz Amplitude: 0.75mm or acceleration 98m/s² (whichever is less severe) Total Duration: 6h Sub-clause 4.23 Sub-clause 4.23.2 Test temperature: 125°C Duration 16h Sub-clause 4.23.3 Test Method: 2 Test temperature: 55°C (Severity (2)) Sub-clause 4.23.4 Test temperature: -55°C Duration: 2h 8kPa Sub-clause 4.23.6 Test method: 2 Test temperature: 55°C (Severity (2)) Number of cycles: 5 Sub-clause 4.23.7 The applied voltage shall be the rated voltage or the limiting element voltage, whichever is smaller. Duration: 1 min. Sub-clause 4.25.1 Ambient temperature: 70°C±2°C Duration: 1000h Voltage applied 1.5h on and 0.5h off The applied voltage shall be the rated voltage or the limiting element voltage, whichever is smaller Examination at 48h, 500h and 1000h Dimensions Shown for reference purposes only. Specifications subject to change No Visible Damage Legible marking ΔR ± %+ . Ω No visible damage ΔR ± %+ . Ω No visible damage ΔR ± %+ . Ω No Visible Damage Legible marking ΔR ± %+ .5Ω Insulation Resistance: R MΩ No visible damage ΔR ± %+ .5Ω Insulation Resistance: R GΩ For Email, phone or live chat, go to: www.te.com/help Carbon Composition Resistors Variation of Resistance with Temperature Damp Heat, Steady State Endurance at upper category temperature At -55°C Resistance Temp. Range Coefficient R KΩ +6.5-0(%) R KΩ +10-0(%) R KΩ +13-0(%) R MΩ +15-0(%) R> MΩ +20-0% At +125°C Resistance Temp. Range Coefficient R KΩ +1-5(%) R KΩ 0-6(%) R KΩ 0-7.5(%) R MΩ 0-10(%) R> MΩ 0-15(%) Sub-clause 4.8 -55°C / +20°C +20°C / +125°C Sub-clause 4.24 Ambient Temperature: 40°C±2°C Relative Hu idity: 9 ⁺²/₋ % a) 1st group: without voltage applied b) 2nd group: DC voltage applied continuously in accordance with subclause 4.24.2.1b c) 3rd group: DC voltage – 20v±2v shall be applied continuously. Sub-clause 4.25.3 Ambient temperature: 125°C±2°C Duration: 1000h Examination at 48h, 500h and 1000h Visual examination Resistance At 1000h only: Insulation Resistance No Visible Damage Legible marking ΔR ± %+ .5Ω Insulation resistance MΩ No Visible Damage ΔR ± %+ .5Ω I sulatio Resista ce GΩ Packaging Taping in accordance with JIS C 0806-1:1999 W CBT25 CBT50 1773192 Rev D 03/2019 52.4 +1.6 -1.4 Dimensions in millimetres unless otherwise specified P L -L Z S T t 5.08±0.38 1.0 max 1.0 max 3.2 min 6.0±0.5 0.5 max Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Carbon Composition Resistors Packaging Notes: The direction of the color codes should be unified. No component shall be missed. Wire leads shall be free from kinks and bends. Pitch tolerance is 2mm for 20 pitches (100±2mm). The edge waving on tape shall not be more than ±1.0mm through a length of 300mm. The reinforcement of the tape cutting should be reinforced by a new tape (30mm min) in 3mm limits and ensuring 1 pitch dimension as shown below. Tape in Box (Ammo Pack) Code CBT25 CBT50 No Code Qty per Box 2000 2000 a 60±5 65±5 b 75±5 75±5 C 275±5 455±5 How To Order 1773192 Rev D 03/2019 CBT Common Part 25 Size J Tolerance CBT – Carbon Composition Resistor 25 – 0.25W 50 – 0.5W J – 5% K – 10% M – 20% Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change 10K Resistance Value 1Ω - 1R0 100Ω - 100R 1000Ω KΩ - 1K0 100000Ω (100KΩ - 100K 1000000Ω (1MΩ - 1M0 For Email, phone or live chat, go to: www.te.com/help