CIRH03T40A60PCNF80M32V0

CIRH SERIES (MIL-C-5015 STYLE) Modular Bayonet Lock Connector RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CIRH SERIES (MIL-C-5015 STYLE) HALOGEN FREE BAYONET LOCK CONNECTOR SERIES The Connectors for Industrial Range (CIR) (H - halogen free) is based on the products covered by the American MilC-5015 and the German VG95234 specifications. These connectors are used extensively throughout the mass transportation, entertainment and general industrial markets. CIRH connectors are interchangeable with all corresponding types and feature contact arrangements from MilSTD-1651. Positive coupling is indicated by an audible ‘snap’ and by the alignment of three coloured dots on the receptacle and on the coupling nut of the plug connector. To enhance service life in applications where the connectors are likely to experience severe vibration or repeated mating, CIRH connectors feature stainless steel anti-wear pins at the critical point of the receptacle coupling ramps. In response to safety and environmental requirements, CIRH connectors have as standard, low fire hazard/halogen free rubber insulators which have been independently tested and shown to conform with the requirements of European specification EN 45545-2 (HL3, R22/R23), French specification NF F 16-101 classification 12 F1 and to British specification BS 6853 app. A clause A.9 and app. B clause B.5.1. Connector shells can also be supplied with cadmium free plating finishes. Protection against water and dust ingress is provided by the use of a dynamic seal ring under the coupling nut and by an individual wire seal grommet at the rear of the connector. A wavy washer assembly, also under the coupling nut and a comprehensive range of back shells and accessories, ensure excellent continuity and shielding characteristics between mated connectors where the effects of EMI and RFI must be eliminated. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CONTENTS General Information....................................................................... 2 Electrical Data.................................................................................. 3 Part Number Explanation............................................................ 4 F80 Contact Arrangements...................................................5-19 F80 Contact Arrangement Selection Chart..................20-21 Alternative Insert Orientations......................................... 22-23 F80 Crimp Contacts - Pin..........................................................24 F80 Crimp Contacts - Socket..................................................25 F80 Crimp Contacts - Low Insertion Force Socket.........26 F80 Crimp Contacts Coaxial - Pin & Socket....................... 27 F80 Crimp Contacts Twinaxial - Pin & Socket.................. 28 Front Mounting Receptacle - CIRH00........................... 29-32 Cable Mounted Receptacle - CIRH01............................. 33-35 Rear Mounting Receptacle - CIRH03............................ 36-40 Size 49 Front Mounting Receptacle - CIRH04...................41 Size 49 Rear Mounting Receptacle - CIRH05....................42 Plug - CIRH06/SE06.............................................................43-45 Plug, Rubber Covered Coupling Nut - CIRHP06.......... 46-48 Size 49 Plug - CIRHP06............................................................ 49 Through Bulkhead Receptacle - CIRH07........................... 50 Rear Mounting Single Hole Receptacle - CIRH09.......... 51-54 Panel Mounted Plug - CIRH12A............................................... 55 Conduit Adaptor With Braid Screen Trap - Type RM (CRA)......................................................................... 56 Non-Locking Cable Clamp - Type D (OCN)....................... 57 Non-Locking Grommet Nut - Type EV................................ 58 Locking 90° Outlet With Cable Clamp & Bushing - Type F............................................................................................ 59 Locking 90° Outlet With Sealed Cable Clamp - Type FC........................................................................................ 60 Locking 90° Outlet - Type FT.................................................. 61 Locking 90° Outlet, RFI - Type FM....................................... 62 Locking Heatshrink Adaptor - Type G (HSA).................... 63 Locking RFI Shielded Adaptor - Type GM (LHSA)......... 64 Non-Locking Heatshrink Adaptor - Type GS (HSAS)....... 65 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR Locking Armoured Conduit Adaptor - Type H (ACA)...... 66 Locking Cable Clamp With Bushing - Type HC................ 67 Locking Sealed Cable Clamp - Type HD............................ 68 Non-Locking Cable Clamp With Bushing - Type JE...... 69 Locking Screened Cable Adaptor - Type M (SCA)........ 70 Non-Locking Conduit Adaptor - Type R (CCA)................ 71 Non-Locking Sealed Cable Clamp - Type RC................... 72 Long Backshell With Cable Clamp & Bushing - Type XLA...................................................................................... 73 Long Backshell With Sealed Cable Clamp - Type XLC...................................................................................... 74 Long Backshell With Grommet - Type SHE....................... 75 Step Up Adaptor.......................................................................... 76 Step Down Adaptor.................................................................... 77 Screened Shell Extender........................................................... 78 PG Threaded Adaptors (DIN 40430)................................... 79 Cable Clamp - Type MS3057A............................................... 80 Cable Clamp - Type MS3057C................................................. 81 Telescopic Bushing...................................................................... 82 Panel Sealing Gaskets................................................................ 83 Protective Caps........................................................................... 84 Wire Sealing Grommets, Dummy Pins, Sockets & Grommet Filler Plugs................. 85 Stowage Receptacles................................................................ 86 Square Flange Receptacle Nut Plates.................................. 87 Square Flange Receptacles, Panel Mounting Details.... 88 Single Hole Mounting Receptacles, Panel Mounting Details............................................................. 89 Contact Insertion & Extraction Tools, Socket Guide Pins....................................................................... 90 F80 Contacts, Crimp & Tooling Data.............................. 91-92 F80 Coax & Twinax Contacts, Crimp & Tooling Data......... 93 RFI Braid Sock, Bandit Strap & Knitmesh Braid........94 GENERAL INFORMATION Standard Data Materials: Connector metalwork: Aluminium alloy Insulator, grommet & bushing: Low Fire Hazard, rubber Contacts: Copper alloy Accessory hardware: Aluminium alloy Standard Plating Finishes: Aluminium parts: Olive drab chromate over zinc cobalt or Olive drab chromate over cadmium plate.* Contacts: Silver or Gold. * Consult TE for alternative finishes. Environmental Ratings: Temperature range: -55°C to + 200°C Shock severity: 75g Vibration: 5-500 Hz long endurance. 30 hour test at 10g. Acceleration: 50g Mechanical Features: Coupling: 3 pin bayonet. Number of contacts: 2 to 85 Contact termination: Crimp or p.c. tail. Sealing: Dynamic sealing ring & individual wire seal grommet. When mated and used with appropriate sealed backshell, IP67 rated. Matings: 2000. CIRH Connectors: CIRH connectors feature stainless steel pins at critical wear points of the cam tracks of all receptacle shells, to protect from wear inflicted by continuous mating/de-mating and vibration. Note: The company reserves the right and may change or vary specification without prior written notice. Stainless Steel Wear Pin PAGE 2 ELECTRICAL DATA Contact Current Ratings Metric *Maximum Current @ 20°C (68°F) * Rated Current @ 85°C (185°F) ** De-rated Current @ 85°C (185°F) 16/16S 15/15S 22A 13A 10A 12 25 41A 23A 20A 8 100 73A 46A 42A 4 160 135A 80A 75A 0 500 245A 150A 135A AWG Contact Size Contact Current De-Rating Curve Operating Current - Amperes 250 500 (0) 200 150 160 (4) 100 60/100 (8) 50 25 (12) 15S (16S) 15 (16) 0 10 (20) 20 40 60 80 Temperature ºC 100 120 Contact Arrangement Service Ratings Service Rating Inst. A D E Working Voltage DC or AC Peak 350 V 700 V 1,250 V 1,750 V Voltage Proof AC RMS 1,000 V 2,000 V 2,800 V 3,500 V Minimum Flashover AC RMS 1,400 V 2,800 V 3,600V 4,500 V RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR PART NUMBER EXPLANATION CIRH 06 Series Prefix F 28 21 Accessory Type Shell Style P C Contact Arrangement Shell Size N Contact Termination Contact Type F80 ** Contact Style Insert Orientation Contact Supply Modification Code Series Prefix: CIRH Low Fire Hazard Shell Style: 00 4 Hole Square flange receptacle, front panel mounted. 01 Cable mounted receptacle. 03 4 Hole Square flange receptacle, rear panel mounted. 06 Plug. No RFI grounding. P06 Plug, rubber covered coupling nut. No RFI grounding. SE06 Plug with RFI grounding. 07 Through bulkhead receptacle 08 Plug with 900 angle outlet. No RFI grounding. SE08 Plug with 900 angle outlet. RFI grounding. 09 Single hole mounted receptacle. Accessory Type: ** See relevant catalogue pages. Shell Size: 10SL– 49. Contact Arrangement: See pages 5 - 22 Contact Type: P = Pin, S = Socket, H pin/socket assembly for bulkhead connector 07. Contact Termination: C crimp removeable, (except for style 07 no designation in part number). Insert orientation: N normal, WXYZ alternative insert positions. See pages 25 & 26 Contact style: F80 Modification Code: M11 Zinc Colbalt Plating with Green passivate finish M32 Zinc Colbalt Plating with Black passivate finish M14 Zinc Colbalt Plating with Black passivate finish and tapped mounting holes M35 Zinc Colbalt Plating with Green passivate finish and tapped mounting holes Others Consult TE Contact Supply: Leave blank for connectors supplied with silver contacts P3 for gold contacts. V0 for connectors supplied without contacts. PAGE 4 F80 CONTACT ARRANGEMENTS 1 Contact Contact Arrangement No. Contacts x Size AWG (Metric) 22-7 1 x #0 (100) 2 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 10SL-4 14S-9 18-3 20-23 2 x #16S (15S) 2 x #16S (15S) 2 x #12 (25) 2 x #0 (100) A A D A C B C Contact Arrangement No. Contacts x Size AWG (Metric) A A A CB B 22-1 24-9 28-T2 32-5 2 x #8 (100) 2 x #4 (160) 2 x Co Ax 2 x #0 (500) 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS A A 3 Contacts CB C B A C Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating A BC A CB B 10SL-3 14S-7 16S-5 16-10 3 x #16S (15S) 3 x #16S (15S) 3 x #16S (15S) 3 x #12 (25) A A A A 15/15S 25 (16/16S) (12) Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 15/15S 100 25 15/15S 25 (16/16S)(8) (12) 16/16S) (12) 100 160 (8) (4) 160 500 (4) (0) 20-3 22-2 14S-1 16S-5 3 x #12 (25) 3 x #8 (100) 3 x #16S (15S) 3 x #16S (15S) D D No. Contacts x Size AWG (Metric) 160 (4) 500 (0) 15/15S 25 15/15S 100 15/15S 25 160 100 25500160 100 (16/16S) (12) (16/16S) (8) (16/16S) (12) (4) (8) (12)(0) (4) (8) Contact Arrangement 100 (8) 500 160 (0) (4) 500 (0) 18-22 20-19 28-6 28-3 3 x #16 (15) 3 x #8 (100) 3 x #4 (160) 3 x #8 (100) 15/15S 25 (16/16S) (12) 100 (8) 160 (4) 500 (0) PAGE 6 500 (0) F80 CONTACT ARRANGEMENTS 4 Contacts D C D C A B A B D DA AD A C CB BC B Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 20-4 24-22 32-17 36-5 4 x #12 (25) 4 x #8 (100) 4 x #4 (160) 4 x #0 (500) D D D A 40-E4 49-A4 14S-2 18-4 4 x #0 (500) 4 x #0 (500) 4 x #16S (15S) 4 x #16 (15) E D 15/15S 25 (16/16S) (12) Contact Arrangement No. Contacts x Size AWG (Metric) 15/15S 15/15S 25 (16/16S) (16/16S) (12) 25 100 (12) (8) 100 160 (8) (4) 160 500 (4) (0) 22-22 32-C17 49-D4 4 x #8 (100) 4 x COAX 2 x #0000 2 x #12 (25) 500 (0) 15/15S 25 160 15/15S1002515/15S 100 25500 160100 500160 (16/16S) (12) (4) (16/16S)(8) (12) (8) (12)(0) (4) (8) (0)(4) (16/16S) 500 (0) 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 100 (8) 160 (4) 500 (0) 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS 5 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating D 14S-5 16S-8 A 18-11 40-A5 B C 5 x #16S (15S) 5 x #16S (15S) 5 x #12 (25) 5 x#0 (500) Inst. A D A 15/15S 15/15S 25 25 100 100 160 160 500 500 15/15S 25 100 160 500 (16/16S) (16/16S) (12) (12) (8) (8) (4) (4) (0) (0) (16/16S) (12) (8) (4) (0) Contact Arrangement No. Contacts x Size AWG (Metric) 16S-8 20-14 24-12 5 x #16 (15) 3 x #12 (25) 2 x #8 (100) 2 x #4 (160) 3 x #12 (25) 6 Contacts F C B No. Contacts x Size AWG (Metric) Service Rating C C A A D D E D E E Contact Arrangement F F A B B 14S-6 18-12 28-22 20-8 40-D6 6 x #16S (15S) 6 x #16 (15) 3 x #16 (15) 3 x #4 (160) 4 x #16 (15) 2 x #8 (100) 3 #16 (15) 3 #0 (500) Inst. A D 15/15S 25 (16/16S) (12) 100 (8) 160 (4) 500 (0) PAGE 8 F80 CONTACT ARRANGEMENTS 7 Contacts C F F F C F A C C A A A D ED E D E D E B B B B Contact Arrangement No. Contacts x Size AWG (Metric) 16S-1 20-15 24-2 D 7 x #16S (15S) 7 x #12 (25) 7 x #12 (25) A A D A Service Rating A G F E Contact Arrangement No. Contacts x Size AWG (Metric) CF F H A G GB H E D E A GB F A B C H ED D 7 x #8 (100) B B C H C 24-10 A C D 24-27 14S-A7 18-9 28-10 7 x #16 (15) 7 x #16S (15S) 5 x #16 (15) 2 x #12 (25) 3 x #12 (25) 2 x #8 (100) 2 x #4 (160) Service Rating A 8 Contacts G A G B A E H D E Contact Arrangement H D A B C C F CF F G B E H D 20-7 22-18 22-23 28-8 No. Contacts x Size AWG (Metric) 8 x #16 (15) 8 x #16 (15) 8 x #12 (25) 2 x #4 (160) 6 x #16 (15) Service Rating A,B,H,G = D, Balance = A A,B,F,G,H = D, Balance = A H = D, Balance = A 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS 9 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 20-A9 20-16 20-18 D A 9 x #12 (25) 2 x #12 (25) 6x #16 (15) 3 x #12 C (25) B J = D. Balance = Inst. A A B B A B E D D G J F H A E G No. Contacts x Size AWG (Metric) Service Rating ED C D B C G D F A E G H J Contact Arrangement CB A C G J F D BC A B D FE 6 x #12 (25) 3 x #8 (100) C A EF F H JF H C G HA EJ G H J 24-11 H J 28-A9 28-1 28-T9 4 x #4 (160) 5 x #16 (15) 3 x #8 (100) 6x #12 (25) 5 x #16 (15) 4 x COAX 18-1 18-19 49-10 10 x #16 (15) 10 x #16 (15) 4 x #12 (25) 6 x # 0 (500) B,C,F,G = A. Balance = Inst. A D A 10 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 15/15S 25 (16/16S) (12) 100 (8) 160 (4) 500 (0) PAGE 10 F80 CONTACT ARRANGEMENTS 11 Contacts 12 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 20-33 11 x #16 (15) A Service Rating Contact Arrangement D A 49-A12 No. Contacts x Size AWG (Metric) C B 5 x #8 (100) 7 x #4 (160) D Service Rating 13 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 32-A13 20-11 28-C1 13 x #12 (25) 13 x #16 (15) 12 x #16 (15) 1 x COAX D Service Rating 14 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 20-27 22-19 28-20 36-D78 14 x #16 (15) 14 x #16 (15) 4 x #16 (15) 10 x #12 (25) 10 x #8 (100) 4 x #16 (15) A A A 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS 16 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 24-7 24-5 14 x #16 (15) 2 x #12 (25) 16 x #16 (15) D A 32-68 C B 4 x #4 (160) 12 x #16 (15) A Service Rating 17 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 20-29 17 x #16 (15) A Service Rating 19 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 20-A48 22-14 24-67 32-76 19 x #16 (15) 19 x #16 (15) 19 x #12 (25) 19 x #12 (25) Inst. A A A 15/15S 25 (16/16S) (12) 100 (8) 160 (4) 500 (0) PAGE 12 F80 CONTACT ARRANGEMENTS 20 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 21 Contacts 28-16 20 x #16 (15) A Service Rating Contact Arrangement D No. Contacts x Size AWG (Metric) C A 40-D21 B 20 x #12 (25) 1 x #8 (100) D Service Rating 22 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 28-11 36-A22 18 x # 16 (15) 4 x # 12 (25) 22 x # 12 (25) A 23 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 24 Contacts 32-6 2 x #4 (160) 3 x #8 (100) 2 x #12 (25) 16 x #16 (15) Contact Arrangement 24-28 No. Contacts x Size AWG (Metric) Service Rating Inst. 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 24 x #16 (15) 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS 25 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 24-A25 25 x #16 (15) D A C B A 26 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 28-12 28-13 26 x #16 (15) 28-12 Rotated by 1000 26 x #16 (15) A A 40-A31 32-31 31 x #12 (25) 31 x #16 (15) 31 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating D 15/15S 25 (16/16S) (12) 100 (8) 160 (4) 500 (0) PAGE 14 F80 CONTACT ARRANGEMENTS 32 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating D A C B 49-D32 26 x #12 (25) 2 x #8 (100) 4 x Coax D 35 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 28-15 32-7 40-A35 35 x #16 (15) 28 x #16 (15) 7 x #12 (25) 35 x #12 (25) A A,B,H & J = Inst. Balance = A D 37 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 28-21 37 x #16 (15) A 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS 38 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating D A C B 40-A38 38 x #12 (25) A 47 Contacts Contact Arrangement 36-7 36-16 40 x #16 (15) 7 x #12 (25) 36-7 Rotated by 1000 Service Rating A A Contact Arrangement 36-17 40-9 36-7 Rotated by 2500 1 x #8 (100) 22 x #12 (25) 24 x #16 (15) No. Contacts x Size AWG (Metric) No. Contacts x Size AWG (Metric) Service Rating A 15/15S 25 (16/16S) (12) 100 (8) 160 (4) 500 (0) PAGE 16 F80 CONTACT ARRANGEMENTS 48 Contacts Contact Arrangement 36-10 36-11 48 x #16 (15) 36-10 Rotated by 1000 Service Rating A A Contact Arrangement 36-12 36-A48 36-10 Rotated by 2500 48 x # 16 (15) A Inst. 49-A49 49-D1 38 x #16 (15), 4 x #12 (25) 5 x #8 (100), 2 x #4 (160) 44 x #16 (15) 5 x #4 (160) D D No. Contacts x Size AWG (Metric) No. Contacts x Size AWG (Metric) Service Rating D A C B 49 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS 55 Contacts 54 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Service Rating 32-22 54 x #16 (15) No. Contacts x Size AWG (Metric) D A C B No. Contacts x Size AWG (Metric) 32-A55 55 x #16 (15) A 60 Contacts 57 Contacts Contact Arrangement Contact Arrangement 49-A57 54 x #12 (25) 3 x Coax Contact Arrangement 40-A60 No. Contacts x Size AWG (Metric) 60 x #16 (15) Service Rating A 68 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 49-A68 49-D68 68 x # 12 (25) 57 x #12 (25) 10 x #16 (15) 1 x Coax 15/15S 25 (16/16S) (12) 100 (8) 160 (4) 500 (0) PAGE 18 F80 CONTACT ARRANGEMENTS 74 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 75 Contacts 49-74 74 x # 16 (15) 76 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) Contact Arrangement D A C B No. Contacts x Size AWG (Metric) 49-D75 73 x # 16 (15) 2 x Coax 85 Contacts 49-A76 76 x # 12 (25) Contact Arrangement 40-56 No. Contacts x Size AWG (Metric) 85 x # 16 (15) A Service Rating 95 Contacts Contact Arrangement No. Contacts x Size AWG (Metric) 49-A95 95 x # 16 (15) 15/15S 25 (16/16S) (12) RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 100 (8) 160 (4) 500 (0) F80 CONTACT ARRANGEMENTS SELECTION CHART Contact Size AWG(Metric) & Current Rating (Derated) Amps at 850 C Shell Cont. Size Arr. 10SL 10SL 14S 14S 14S 14S 14S 14S 14S 16S 16S 16S 16 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 22 22 22 22 22 22 22 22 24 24 24 24 24 24 24 24 24 24 24 24 3 4 1 2 5 6 7 A7 9 1 5 8 10 1 3 4 9 11 12 19 22 3 4 7 8 A9 11 14 15 16 18 19 23 27 29 33 A48 1 2 7 14 18 19 22 23 2 5 7 9 10 11 12 22 A25 27 28 67 No. of Cts. 3 2 3 4 5 6 3 7 2 7 3 5 3 10 2 4 7 5 6 10 3 3 4 8 6 9 13 5 7 9 9 3 2 14 17 11 19 2 3 1 19 8 14 4 8 7 16 16 2 7 9 5 4 25 7 24 19 6/16S 12 8 4 0 (15/15S) (25) (100) (160) (500) 3x10A 2x10A 3x10A 4x10A 5x10A 6x10A 3x10A 7x10A 2x10A 7x10A 3x10A 5x10A 3x20A 10x10A 2x20A 4x10A 5x10A 2x20A 5x20A 6x10A 10x10A 3x10A 3x20A 4x20A 8x10A 4x10A 2x20A 9x20A 13x10A 7x10A 6x10A 3x20A 7x20A 2x20A 3x20A Shell Orientation Service N N A A NX NW NWXY Inst. Inst. A NWXYZ NWZ NWXYZ NWY NWXY NWXYZ NWXYZ A A A A A *A&Inst D NXY NWZ NXY NXY NWXYZ NWXY NWXYZ A A A A D D *A&D NXY NWZ *D&Inst A NWZ NWXYZ NWXYZ A A A NWXYZ NWZ NZ NXY A A A Inst NWXYZ D NWXYZ NWXYZ NWXYZ A *A&D A NWY NWZ *A&D D NWXYZ A NWZ NWXYZ A A NWXY NWXYZ NWZ NWXYZ NWXYZ D A E Inst. A Rating 2x42A 3x42A 2x42A 14x10A 17x10A 11x10A 19x10A 2x42A 3x42A 1x135A 19x10A 8x10A 14x10A 4x42A 8x20A 7x20A 16x10A 14x10A 2x20A 2x75A 6x20A 3x20A 7x42A 3x42A 2x75A 4x42A 25x10A 7x10A 24x10A *Contact Arrangements/Service Ratings 18-1 Contacts B,C,F,G = A. 20-7 Contacts C,D,E,F = A 22-23 Contact H = D 20-A9 Contact J = D 22-18 Contacts A,B,F,G,H = D 19x20A Balance = Inst. Balance = D Balance = A Balance = Inst. Balance = A PAGE 20 F80 CONTACT ARRANGEMENTS SELECTION CHART Contact Size AWG(Metric) & Current Rating (Derated) Amps at 850 C Shell Cont. Size 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 32 32 32 32 32 32 32 32 32 32 32 36 36 36 36 36 36 36 36 36 36 36 36 40 40 40 40 40 40 40 40 40 40 49 49 49 49 49 49 49 49 49 49 49 49 49 49 Arr. 1 C1 T2 3 6 8 T9 10 11 12 13 15 16 20 21 22 A9 5 6 7 A13 17 C17 22 31 A55 68 76 5 7 10 11 12 16 17 A22 A48 54 D68 D78 56 A5 D6 9 D21 A31 A35 A38 A60 E4 D1 A4 D4 A10 A12 D32 A49 A57 A68 D68 74 D75 A76 A95 No. of Cts. 9 13 2 3 3 8 9 7 22 26 26 35 20 14 37 6 9 2 23 35 13 4 4 54 31 55 16 19 4 47 48 48 48 47 47 22 48 39 14 14 85 5 6 47 21 31 35 38 60 4 49 4 4 10 12 32 49 57 68 68 74 75 76 95 6/16S 12 8 4 0 (15/15S) (25) 6x20A (100) 3x42A (160) (500) Shell Orientation Service NWXYZ NWXY NWXYZ NWXYZ NWXYZ NWXYZ NWXYZ NWXYZ A A A A A A A D A NWXYZ NWXYZ NWXY *A&Inst D D NWXYZ A NWXYZ A NWXYZ NXY NWXYZ NWXYZ NWXYZ NW NW A A A A A A A A D Inst A NWXYZ NWZ A A NW NWXYZ NWXYZ NWXYZ NWXYZ NWX NW NW D D D A A E D D NWX NW NW NW D D D D Rating 12x10A 3x42A 3x75A 2x75A 6x10A 5x10A 18x10A 26x10A 26x10A 35x10A 20x10A 4x10A 37x10A 3x10A 5X10A 3x20A 4x20A 2x42A 2x75A 10x20A 3x75A 4X75A 2x135A 16x10A 28x10A 2x20A 7x20A 13x20A 3x42A 2x75A 4x75A 54x10A 31x10A 55x10A 12x10A 4x75A 19x20A 40x10A 48x10A 48x10A 48x10A 40x10A 40x10A 48x10A 31x10A 4x10A 4x10A 85x10A 3x10A 24x10A 4x135A 4x135A 7x20A 7x20A 7x20A 22x20A 8x42A 10x42A 10x42A 5x135A 3x135A 22x20A 20x20A 31x20A 35x20A 38x20A 1X42A 1x42A 60x10A 4x135A 44x10A 5xCoax 4x135A 2X20A 4x20A 38x10A 10x10A 74x10A 73x10A 26x20A 4x20A 54x20A 68x20A 57x20A 76x20A 95x10A *Contact Arrangements/Service Ratings 32-7 Contacts A,B,H,J = Inst RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR Balance = A 6x135A 5x42A 2x42A 5x42A 7x75A 4xCoax 2xCoax ALTERNATIVE INSERT ORIENTATIONS View on Mating Face of Pin Inserts W Z Y B C B A C A C X A N A Contact Arrangement 10SL-3 10S-4 14S-1 14S-2 14S-5 14S-6 14S-7 14S-A7 14S-9 16S-1 16S-5 16S-8 16-10 18-1 18-3 18-4 18-9 18-11 18-12 18-19 18-22 20-3 20-4 20-7 20-8 20-A9 20-11 20-14 20-15 20-16 20-18 20-19 20-23 20-27 20-29 20-33 20-A48 22-1 22-2 22-7 22-14 22-18 22-19 22-22 22-23 24-1 24-5 24-7 24-9 24-10 24-11 24-12 24-22 24-A25 24-27 24-28 24-67 C A C B B B Angular Displacement Of Insert N Yellow W Blue X Green Y Purple Z White 0 0 0 0 0 0 0 0 0 0 0 0 110 90 90 70 80 70 90 70 35 0 0 0 80 0 0 0 70 45 80 0 180 270 145 215 145 170 180 145 110 215 265 270 215 250 170 265 120 240 145 110 110 215 250 250 110 250 110 110 250 250 110 250 80 280 290 280 290 290 325 280 290 280 0 0 0 80 80 35 280 280 325 0 0 0 0 35 80 0 70 145 215 290 0 0 0 80 80 80 110 110 110 250 250 250 280 280 280 0 0 35 80 0 80 110 250 280 0 0 80 35 110 250 280 325 0 0 0 0 0 45 80 80 80 80 110 110 250 250 110 250 325 280 280 250 280 280 280 280 335 PAGE 22 ALTERNATIVE INSERT ORIENTATIONS View on Mating Face of Pin Inserts W Z Y B C B A C A C X A N A Contact Arrangement 28-1 28-C1 28-T2 28-3 28-6 28-8 28-T9 28-10 28-11 28-12 28-13 28-15 28-16 28-20 28-21 28-22 28-A9 32-5 32-6 32-7 32-A13 32-17 32-C17 32-22 32-31 32-A55 32-68 32-76 36-5 36-7 36-10 36-11 36-12 36-16 36-17 36-A22 36A48 36-54 36-D68 40-56 40-A5 40-D6 40-9 40-D21 40-A31 40-A35 40-A38 40-A60 40-E4 49-D1 49-A4 49-D4 49-A10 49-A12 49-D32 49-A49 49-57 49-A68 49-D68 49-74 49-D75 49-A76 49-A95 C A C B B B Angular Displacement Of Insert N Yellow W Blue X Green Y Purple Z White 0 0 0 0 0 0 0 0 0 80 90 110 180 250 270 280 80 80 80 80 70 110 110 110 110 110 145 250 250 250 250 250 215 260 280 280 280 280 290 280 0 0 0 80 65 45 125 130 110 235 230 250 280 295 0 80 110 250 280 0 80 110 250 280 0 0 0 0 0 0 0 0 0 0 0 80 110 120 110 125 250 240 250 235 280 80 65 67 110 250 280 0 0 72 33 144 216 288 270 0 0 0 0 0 0 0 0 80 80 70 37 80 45 80 80 110 130 74 110 110 250 230 285 250 280 290 322 280 0 0 0 0 80 80 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 80 80 80 150 280 280 F80 CRIMP CONTACTS PIN Metric Imperial For standard gold plating, add P3 to the end of the part number. Contact Size AWG (Metric) Part Number A B C Conductor CSA mm2 L 16S/20 CIRB16S/20KPKF80 3,20 0.126 2,65 0.104 1,10 0.043 0,50/0,60 26,60 1.047 16S/18 CIRB16S/18KPKF80 3,20 0.126 2,30 0.091 1,25 0.049 0,75/0,93 26,60 1.047 16S (15S) CIRB16SKPKF80 3,20 0.126 2,75 0.108 1,75 0.069 0,93/1,50 26,60 1.047 16S/14 CIRB16S/14KPKF80 3,20 0.126 2,90 0.114 1,80 0.071 1,94/2,08 26,60 1.047 16/22 CIRB16/22KPKF80 3,20 0.126 2,30 0.091 0,90 0.035 0,22/0,34 31,75 1.250 16/20 CIRB16/20KPKF80 3,20 0.126 2,65 0.104 1,10 0.043 0,50/0,75 31,75 1.250 16/18 CIRB16/18KPKF80 3,20 0.126 2,30 0.091 1,25 0.049 0,75/0,93 31,75 1.250 16 (15) CIRB16KPKF80 3,20 0.126 2,75 0.108 1,75 0.069 0,93/1,50 31,75 1.250 16/14 CIRB1614KPKF80 3,20 0.126 2,90 0.114 1,80 0.071 1,94/2,08 31,75 1,250 16/12 CIRB16/12KPKF80 3,20 0.126 3,80 0.150 2,50 0.098 2,50/3,00 31,75 1.250 12/20 CIRB12/20KPKF80 4,80 0.189 2,65 0.104 1,10 0.043 0,50/0,60 37,50 1.476 12/18 CIRB12/18KPKF80 4,80 0.189 2,30 0.091 1,25 0.049 0,75/0,93 37,50 1.476 12/16 (25/15) CIRB12/16KPKF80 4,80 0.189 2,75 0.108 1,75 0.069 0,93/1,50 37,50 1.476 12/14 CIRB12/14KPKF80 4,80 0.189 2,90 0.114 1,80 0.071 1,94/2,08 37,50 1.476 12 (25) CIRB12KPKF80 4,80 0.189 3,80 0.150 2,50 0.098 2,50/3,00 37,50 1.476 12/10 CIRB1210KPKF80 4,80 0.189 4,40 0.173 3,00 0.118 5,53 37,50 1.476 12/40 (25/40) CIRB12/40KPKF80 4,80 0.189 4,00 0.157 2,70 0.106 4,00 37,50 1.476 8/40 (100/40) CIRB8/40KPKF80 7,80 0.307 5,20 0.205 2,90 0.114 4,00 40,70 1.602 8/12 CIRB8/12KPKF80 7,80 0.307 3,80 0.150 2,50 0.098 2,50 40,70 1.602 8/10 CIRB8/10KPKF80 7,80 0.307 5,20 0.205 3,30 0.130 5,53 40,70 1.602 8 CIRB8KPKF80 7,80 0.307 6,80 0.268 4,55 0.179 9,00 40,70 1.602 (100/60) CIRB100/60KPKF80 7,80 0.307 5,50 0.217 3,40 0.134 6,00 40,70 1.602 (100) CIRB100KPKF80 7,80 0.307 7,00 0.276 4,40 0.173 10,00 40,70 1.602 4/10 CIRB4/10KPKF80 11,00 0.433 5,20 0.205 3,30 0.130 553 41,25 1.624 4 CIRB4KPKF80 11,00 0.433 9,55 0.376 7,10 0.280 22,00 41,25 1.624 (160) CIRB160KPKF80 11,00 0.433 9,45 0.372 5,70 0.224 16,00 41,25 1.624 0 CIRB0KPKF80 15,00 0.591 14,35 0.565 11,50 0.453 53,0 44,50 1.752 (500/160) CIRB500/160KPKF80 15,00 0.591 9,45 0.372 5,70 0.224 16,00 44,50 1.752 (500/250) CIRB500/250KPKF80 15,00 0.591 10,00 0.394 7,00 0.276 25,00 44,50 1.752 (500/350) CIRB500/350KPKF80 15,00 0.591 11,90 0.468 8,00 0.315 35,00 44,50 1.752 (500) CIRB500KPKF80 15,00 0.591 14,35 0.565 9,80 0.386 50,00 44,50 1.752 PAGE 24 F80 CRIMP CONTACTS SOCKET Metric Imperial For standard gold plating, add P3 to the end of the part number. Contact Size AWG (Metric) Part Number A B C D Conductor CSA mm2 L 16S/20 CIRB16S/20KSKF80 3,20 0.126 - 2,65 0.104 1,10 0.049 0,50/0,60 26,60 1.047 16S/18 CIRB16S/18KSKF80 3,20 0.126 - 2,30 0.091 1,25 0.069 0,75/0.93 26,60 1.047 16S (15S) CIRB16SKSKF80 3,20 0.126 - 2,75 0.108 1,75 0.069 0,93/1,50 26,60 1.047 16S/14 CIRB16S/14KSKF80 3,20 0.126 - 3,90 0.114 1,80 0.071 1,94/2,08 26,60 1.047 16/22 CIRB16/22KSKF80 3,20 0.126 - 2,30 0.091 0,90 0.035 0,22/0,34 36,50 1.437 16/20 CIRB16/20KSKF80 3,20 0.126 - 2,65 0.104 1,10 0.049 0,50/0,75 36,50 1.437 16/18 CIRB16/18KSKF80 3,20 0.126 - 2,30 0.091 1,25 0.049 0,75/0,93 36,50 1.437 16 (15) CIRB16KSKF80 3,20 0.126 - 2,75 0.108 1,75 0.07 0,93/1,50 36,50 1.437 16/14 CIRB16/14KSKF80 3,20 0.126 - 2,90 0.114 1,80 0.071 1,94/2,08 36,50 1.437 16/12 CIRB16/12KSKF80 3,20 0.126 - 3,80 0.150 2,50 0.098 2,50/3,00 36,50 1.476 12/20 CIRB12/20KSKF80 4,80 0.189 - 2,65 0.104 1,10 0.049 0,50/0,60 37,50 1.476 12/18 CIRB12/18KSKF80 4,80 0.189 - 2,30 0.091 1,25 0.049 0,75/0,93 37,50 1.476 12/16 (25/15) CIRB12/16KSKF80 4,80 0.189 - 2,75 0.108 1,75 0.069 0,93/1,50 37,50 1.476 12/14 CIRB12/14KSKF80 4,80 0.189 - 2,90 0.114 1,80 0.071 1,94/2,08 37,50 1.476 12 (25) CIRB12KSKF80 4,80 0.189 - 3,80 0.150 2,50 0.098 2,50/3,00 37,50 1.476 12/10 CIRB1210KSKF80 480 0.189 - 4,40 0.173 3,00 0.118 5,53 37,50 1.476 12/40 (25/40) CIRB12/40KSKF80 4,80 0.189 - 4,00 0.157 2,70 0.106 4,00 37,50 1.476 8/40 CIRB8/40KSKF80 7,80 0.307 6,50 0.256 5,20 0.204 2,90 0.114 4,00 40,70 1.602 8/12 CIRB8/12KSKF80 7,80 0.307 6,50 0.256 3,80 0.150 2,50 0.098 2,50/3,00 40,70 1.602 8/10 CIRB8/10KSKF80 7,80 0.307 6,50 0.256 4,40 0.173 3,00 0.118 5,53 40,70 1.602 8 CIRB8KSKF80 7,80 0.307 6,50 0.256 6,80 0.268 4,55 0.179 9,00 40,70 1.602 (100/60) CIRB100/60KSKF80 7,80 0.307 6,50 0.256 5,50 0.217 3,40 0.134 6,00 40,70 1.602 (100) CIRB100KSKF80 7,80 0.307 6,50 0.256 7,00 0.276 4,40 0.173 10,00 40,70 1.602 4/10 CIRB4/10KSKF80 11,10 0.437 6,50 0.256 5,20 0.205 3,30 0.130 5,53 41,25 1.624 4 CIRB4KSKF80 11,10 0.437 8,60 0.339 9,55 0.376 7,10 0.280 22,00 41,25 1.624 (160) CIRB160KSKF80 11,10 0.437 8,60 0.339 9,45 0.372 5,70 0.224 16,00 41,25 1.624 0 CIRB0KSKF80 15,10 0.594 13,20 0.520 14,35 0.565 11,50 0.453 53,00 44,50 1.752 (500/160) CIRB500/160KSKF80 15,10 0.594 13,20 0.520 9,45 0.372 5,70 0.224 16,00 44,50 1.752 (500/250) CIRB500/250KSKF80 15,10 0.594 13,20 0.520 10,00 0.394 7,00 0.276 25,00 44,50 1.752 (500/350) CIRB500/350KPKF80 15,10 0.594 13,20 0.520 11,90 0.469 8,00 0.315 35,00 44,50 1.752 (500) CIRB500KPKF80 15,10 0.594 13,20 0.520 14,35 0.565 9.80 0.386 50,00 44,50 1.752 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR F80 CRIMP CONTACTS LOW INSERTION FORCE SOCKET Metric Imperial Standard finish = gold plated. Contact Size AWG (Metric) Part Number A B C Conductor CSA mm2 L 16S (15S) CIRB16SKLKF80P3 3,20 0.126 2,75 0.108 1,75 0.069 1,00/1,50 26,60 1.047 16/22 CIRB16/22KLKF80P3 3,20 0.126 2,30 0.091 0,90 0.035 0,22/0,34 36,50 1.437 16/20 CIRB16/20KLKF80P3 3,20 0.126 2,65 0.104 1,10 0.043 0,50/0,60 36,50 1.437 16/18 CIRB16/18KLKF80P3 3,20 0.126 2,30 0.091 1,25 0.049 0,75/0,93 36,50 1.437 16 (15) CIRB16KLKF80P3 3,20 0.126 2,75 0.108 1,75 0.069 1,00/1,50 36,50 1.437 16/14 CIRB16/14KLKF80P3 3,20 0.126 2,90 0.114 1,80 0.071 1,94/2,08 36,50 1.437 16/12 CIRB16/12KLKF80P3 3,20 0.126 3,80 0.150 2,50 0.098 2,50/3,00 36,50 1.437 12/40 (25/40) CIRB12/40KLKF80P3 4,80 0.189 4,00 0.157 2,70 0.106 4,00 37,50 1.476 12/20 CIRB12/20KLKF80P3 4,80 0.189 2,65 0.104 1,10 0.043 0,50/0,60 37,50 1.476 12/18 CIRB12/18KLKF80P3 4,80 0.189 2,30 0.091 1,25 0.049 0,75/0,93 37,50 1.476 12/16 CIRB12/16KLKF80P3 4,80 0.189 2,75 0.108 1,75 0.069 1,00/1,50 37,50 1.476 12/10 CIRB12/10KLKF80P3 4,80 0.189 4,40 0.175 3,00 0.118 5,53 37,50 1.476 12 (25) CIRB12KLKF80P3 4,80 0.189 3,80 0.1508 2,50 0.098 2,50/3,00 37,50 1.476 PAGE 26 F80 CRIMP CONTACTS COAXIAL PIN & SOCKET Pin Contact L ØC ØB ØC ØB ØD ØD ØA ØA L * Important Note. Consult TE for suitable contact arrangement details. Metric Imperial Contact Size AWG* Part Number A B C D L Use With Conductors 4 CIRB 4 CKPK F80 P1 001 11,10 0.437 9,80 0.386 5,20 0.205 1,07 0.042 44,70 1.760 0.5 mm2 4 CIRB 4 CKPK F80 P1 002 11,10 0.437 9,80 0.386 7,50 0.295 1,75 0.069 44,70 1.760 1.0 mm2 Socket Contact L ØC ØB ØC ØB ØD Metric Imperial ØD ØA ØA L * Important Note. Consult TE for suitable contact arrangement details. Contact Size AWG* Part Number A B C D L Use With Conductors 4 CIRB 4 CKSK F80 P1 001 11,10 0.437 9,80 0.386 5,20 0.205 1,07 0.042 43,05 1.695 0.5 mm2 4 CIRB 4 CKSK F80 P1 002 11,10 0.437 9,80 0.386 7,50 0.295 1,75 0.069 43,05 1.695 1.0 mm2 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR F80 CRIMP CONTACTS TWINAXIAL PIN & SOCKET Pin Contact L ØB ØB Contact Size AWG* Part Number A B C D E L Use With Conductors 4 CIRB 4 TKPK F80 P1 11,10 0.437 9,80 0.386 6,00 0.236 1,07 0.042 1,05 0.041 44,70 1.760 0.5 mm2 0.6 mm2 4 CIRB 4 TKPK F80 P1 001 11,10 0.437 9,80 0.386 6,50 0.256 1,30 0.051 1,30 0.051 44,70 1.760 0.75 mm2 1.0 mm2 ØD ØD ØA ØA ØC ØC ØE ØE L * Important Note. Consult TE for suitable contact arrangement details. Metric Imperial Socket Contact L ØB ØB ØD ØD ØA ØA ØC ØC ØE ØE L Metric Imperial * Important Note. Consult TE for suitable contact arrangement details. Contact Size AWG* Part Number A B C D E L Use With Conductors 4 CIRB 4 TKSK F80 P1 11,10 0.437 9,80 0.386 6,00 0.236 1,07 0.042 1,05 0.041 43,05 1.695 0.5 mm2 0.6 mm2 4 CIRB 4 TKSK F80 P1 001 11,10 0.437 9,80 0.386 6,50 0.256 1,30 0.051 1,30 0.051 43,05 1.695 0.75 mm2 1.0 mm2 PAGE 28 SQUARE FLANGE RECEPTACLE FRONT MOUNTING (NO ACCESSORY THREAD) STYLE: CIRH00A/CIRH00A...M6 B Om 4 Tapped holes d2 (M6 MOD.) H E 4 Holes ød1 C øM C P (max. panel thickness) Metric Imperial See page 90 for panel mounting details. Shell Size B Max C Max d1 +0,2 -0 +0.008-0 d2 Thread E Max M Max H Max Om Min Overlap Mated 10SL 17,60 0.693 25,70 1.012 3,20 0.126 M4 0,7-6H 3,00 0.118 16,10 0.634 25,00 0.98 11,10 0.437 14S 18,00 0.709 30,30 1.193 3,20 0.126 M4 0,7-6H 3,40 0.134 19,20 0.756 25,00 0.98 11,10 0.437 16S 18,00 0.709 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 22,40 0.882 25,00 0.98 11,10 0.437 16 22,80 0.898 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 22,40 0.882 32,85 1.293 15,85 0.624 18 23,60 0.929 35,30 1.390 3,20 0.126 M4 0,7-6H 4,20 0.165 25,60 1.008 32,85 1.293 15,85 0.624 20 23,60 0.929 38,30 1.508 3,20 0.126 M4 0,7-6H 4,20 0.165 29,00 1.142 32,85 1.293 15,85 0.624 22 23,60 0.929 41,30 1.626 3,20 0.126 M4 0,7-6H 4,20 0.165 31,90 1.256 32,85 1.293 15,75 0.620 24 25,20 0.992 44,80 1.764 3,70 0.146 M4 0,7-6H 4,20 0.165 35,00 1.378 32,85 1.293 15,75 0.620 28 25,20 0.992 51,10 2.012 3,70 0.146 M5 0,8-6H 4,20 0.165 41,40 1.630 32,85 1.293 15,75 0.620 32 26,80 1.055 57,30 2.256 4,30 0.169 M5 0,8-6H 4,20 0.165 47,80 1.882 32,85 1.293 15,75 0.620 36 26,80 1.055 63,80 2.512 4,30 0.169 M5 0,8-6H 4,20 0.165 52,60 2.071 32,85 1.293 15,75 0.620 40 26,80 1.055 70,20 2.764 4,30 0.169 M5 0,8-6H 4,20 0.165 59,00 2.323 32,85 1.293 15,75 0.620 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR SQUARE FLANGE RECEPTACLE FRONT MOUNTING STYLE: CIRH00T/CIRH00T...M6 B 4 Tapped holes d2 (M6 MOD.) H E 4 Holes ød1 Om C øF P (max. panel thickness when using accessory) Metric Imperial C See page 90 for panel mounting details. Shell Size B Max C Max d1 +0,2 -0 +0.008-0 d2 Thread E Max F Thread Dia. Class 2A H Max P Om Min Overlap Mated 10SL 17,60 0.693 25,70 1.012 3,20 0.126 M4 0,7-6H 3,00 0.118 5 /8" x 24 UNEF 28,78 1.133 3,30 0.130 11,10 0.437 14S 18,00 0.709 30,30 1.193 3,20 0.126 M4 0,7-6H 3,40 0.134 3 /4" x 20 UNEF 28,78 1.133 3,30 0.130 11,10 0.437 16S 18,00 0.709 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 7 /8" x 20 UNEF 28,78 1.133 3,30 0.130 11,10 0.437 16 22,80 0.898 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 7 /8" x 20 UNEF 36,30 1.429 3,30 0.130 15,85 0.624 18 23,60 0.929 35,30 1.390 3,20 0.126 M4 0,7-6H 4,20 0.165 1" x 20 UNEF 36,30 1.429 3,30 0.130 15,85 0.624 20 23,60 0.929 38,30 1.508 3,20 0.126 M4 0,7-6H 4,20 0.165 1 1/8" x 18 UNEF 36,30 1.429 3,30 0.130 15,85 0.624 22 23,60 0.929 41,30 1.626 3,20 0.126 M4 0,7-6H 4,20 0.165 1 1/4" x 18 UNEF 36,30 1.429 3,30 0.130 15,75 0.620 24 25,20 0.992 44,80 1.764 3,70 0.146 M4 0,7-6H 4,20 0.165 1 3/8" x 18 UNEF 36,30 1.429 3,30 0.130 15,75 0.620 28 25,20 0.992 51,10 2.012 3,70 0.146 M5 0,8-6H 4,20 0.165 1 5/8" x 18 UNEF 36,30 1.429 3,30 0.130 15,75 0.620 32 26,80 1.055 57,30 2.256 4,30 0.169 M5 0,8-6H 4,20 0.165 1 7/8" x 16 UN 36,30 1.429 3,30 0.130 15,75 0.620 36 26,80 1.055 63,80 2.512 4,30 0.169 M5 0,8-6H 4,20 0.165 21/16" x 16 UNS 36,30 1.429 3,30 0.130 15,75 0.620 40 26,80 1.055 70,20 2.764 4,30 0.169 M5 0,8-6H 4,20 0.165 2 5/16" x 16 UN 36,30 1.429 3,30 0.130 15,75 0.620 PAGE 30 CIRH ‘00’ STYLE CONNECTOR & ACCESSORY A B CIRH00D CIRH00EV D E CIRH00FC CIRH00FT C CIRH00F F CIRH00FM G H J CIRH00G CIRH00GM CIRH00GS Metric Imperial Shell Size A B C D E F G H J 10SL 109,00 4.291 44,00 1.732 57,00 2.244 58,00 2.283 54,00 2.126 54,00 2.126 49,00 1.929 53,00 2.087 * 14S 107,00 4.213 44,00 1.732 61,00 2.402 60,00 2.362 56,00 2.205 56,00 2.205 49,00 1.929 53,00 2.087 * 16S 104,00 4.094 44,00 1.732 64,00 2.520 64,00 2.520 60,00 2.362 60,00 2.362 49,00 1.929 53,00 2.087 * 16 111,00 4.370 54,00 2.126 71,00 2.795 71,00 2.795 67,00 2.638 67,00 2.638 57,00 2.244 65,00 2.559 * 18 115,00 4.528 54,00 2.126 76,00 2.992 76,00 2.992 72,00 2.835 72,00 2.835 59,00 2.323 65,00 2.559 74,00 2.913 20 114,00 4.488 54,00 2.126 81,00 3.189 82,00 3.228 77,00 3.031 77,00 3.031 60,00 2.362 68,00 2.677 80,00 3.150 22 114,00 4.488 54,00 2.126 81,00 2.189 82,00 3.228 77,00 3.031 77,00 3.031 63,00 2.480 68,00 2.677 80,00 3.150 24 109,00 4.291 54,00 2.126 89,00 3.504 89,00 3.504 85,00 3.346 85,00 3.346 60,00 2.362 68,00 2.677 80,00 3.150 28 119,00 4.685 54,00 2.126 88,00 3.465 89,00 3.504 85,00 3.346 85,00 3.346 63,00 2.480 67,00 2.638 81,00 3.189 32 115,00 4.528 54,00 2.126 98,00 3.858 101,00 3.976 95,00 3.740 95,00 3.740 61,00 2.402 67,00 2.638 80,00 3.189 36 112,00 4.409 54,00 2.126 104,00 4.094 105,00 4.134 101,00 3.976 101,00 3.976 67,00 2.638 68,00 2.677 80,00 3.189 40 N/A 54,00 2.126 111,00 4.370 112,00 4.409 107,00 4.213 107,00 4.213 68,00 2.677 68,00 2.677 80,00 3.189 * Please consult TE for availability. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CIRH ‘00’ STYLE CONNECTOR & ACCESSORY CONT. K L M CIRH00H CIRH00HC CIRH00HD N CIRH00JE P R CIRH00M CIRH00R S CIRH00RC T U CIRH00XLA CIRH00XLC Metric Imperial Shell Size K L M N P R S T U 10SL 50,00 1.969 122,00 4.803 81,00 3.189 121,00 4.764 53,00 2.087 51,00 2.008 82,00 3.228 140,00 5.512 101,00 3.976 14S 50,00 1.969 118,00 4.646 81,00 3.189 118,00 4.646 56,00 2.205 51,00 2.008 82,00 3.228 137,00 5.394 101,00 3.976 16S 50,00 1.969 120,00 4.724 81,00 3.189 115,00 4.528 56,00 2.205 51,00 2.008 82,00 3.228 134,00 5.276 101,00 3.976 16 57,00 2.244 123,00 4.843 88,00 3.465 124,00 4.882 63,00 2.480 60,00 2.362 91,00 3.583 152,00 5.984 121,00 4.764 18 59,00 2.323 124,00 4.882 92,00 3.622 126,00 4.961 66,00 2.598 66,00 2.598 99,00 3.898 148,00 5.827 121,00 4.764 20 59,00 2.323 120,00 4.724 92,00 3.622 123,00 4.843 66,00 2.598 66,00 2.598 99,00 3.898 145,00 5.709 121,00 4.764 22 59,00 2.323 120,00 4.724 92,00 3.622 123,00 4.843 66,00 2.598 66,00 2.598 99,00 3.898 145,00 5.709 121,00 4.764 24 59,00 2.323 107,00 4.213 95,00 3.740 123,00 4.843 66,00 2.598 69,00 2.716 105,00 4.134 142,00 5.591 124,00 4.882 28 59,00 2.323 107,00 4.213 95,00 3.740 124,00 4.882 65,00 2.559 70,00 2.756 106,00 4.173 149,00 5.866 131,00 5.157 32 58,00 2.283 106,00 4.173 100,00 3.937 120,00 4.724 65,00 2.559 69,00 2.716 111,00 4.370 146,00 5.748 137,00 5.394 36 58,00 2.283 106,00 4.173 107,00 4.213 117,00 4.606 65,00 2.559 69,00 2.716 117,00 4.606 143,00 5.630 144,00 5.669 40 58,00 2.283 103,00 4.055 107,00 4.213 114,00 4.488 65,00 2.559 70,00 2.756 112,00 4.409 140,00 5.512 144,00 5.669 PAGE 32 CABLE MOUNTED RECEPTACLE STYLE: CIRH01T Om H C øF D E B Metric Imperial F Thread Dia. Class 2A H Max Om Min Overlap Mated /8" x 24 UNEF 28,78 1.133 11,10 0.437 /4" x 20 UNEF 28,78 1.133 11,10 0.437 /8" x 20 UNEF 28,78 1.133 11,10 0.437 /8" x 20 UNEF 36,30 1.429 15,85 0.624 4,20 0.165 1" x 20 UNEF 36,30 1.429 15,85 0.624 35,10 1.382 4,20 0.165 1 1/8" x 18 UNEF 36,30 1.429 15,85 0.624 41,10 1.618 38,30 1.508 4,20 0.165 1 1/4" x 18 UNEF 36,30 1.429 15,75 0.620 25,20 0.992 44,60 1.756 41,50 1.634 4,20 0.165 1 3/8" x 18 UNEF 36,30 1.429 15,75 0.620 28 25,20 0.992 50,90 2.004 47,80 1.882 4,20 0.165 1 5/8" x 18 UNEF 36,30 1.429 15,75 0.620 32 26,80 1.055 57,10 2.248 54,20 2.134 4,20 0.165 1 7/8" x 16 UN 36,30 1.429 15,75 0.620 36 26,80 1.055 63,80 2.512 60,80 2.394 4,20 0.165 2 1/16" x 16 UNS 36,30 1.429 15,75 0.620 40 26,80 1.055 70,00 2.756 66,70 2.626 4,20 0.165 2 5/16" x 16 UN 36,30 1.429 15,75 0.620 Shell Size B Max C Max D Max E Max 10SL 17,60 0.693 25,20 0.992 20,80 0.819 3,00 0.118 5 14S 18,00 0.709 29,80 1.173 25,60 1.008 3,40 0.134 3 16S 18,00 0.709 32,30 1.272 28,80 1.134 3,40 0.134 7 16 22,80 0.898 32,30 1.272 28,80 1.134 3,40 0.134 7 18 23,60 0.929 34,80 1.370 31,90 1.256 20 23,60 0.929 37,80 1.488 22 23,60 0.929 24 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CIRH ‘01’ STYLE CONNECTOR & ACCESSORY A B CIRH01D CIRH01EV J CIRH01GS G H CIRH01G CIRH01GM K L CIRH01H CIRH01HC M N CIRH01HD CIRH01JE Metric Imperial Shell Size A B G H J K L M N 10SL 109,00 4.291 44,00 1.732 49,00 1.929 53,00 2.087 * 50,00 1.696 122,00 4.803 81,00 3.189 121,00 4.764 14S 107,00 4.213 44,00 1.732 49,00 1.929 53,00 2.087 * 50,00 1.969 118,00 4.646 81,00 3.189 118,00 4.646 16S 104,00 4.094 44,00 1.732 49,00 1.929 53,00 2.087 * 50,00 1.969 120,00 4.724 81,00 3.189 115,00 4.528 16 111,00 4.370 54,00 2.126 57,00 2.244 65,00 2.559 * 57,00 2.244 123,00 4.843 88,00 3.465 124,00 4.882 18 115,00 4.528 54,00 2.126 59,00 2.323 65,00 2.559 74,00 2.913 59,00 2.323 124,00 4.882 92,00 3.622 126,00 4.961 20 114,00 4.488 54,00 2.126 60,00 2.362 68,00 2.677 80,00 3.150 59,00 2.323 120,00 4.724 92,00 3.622 123,00 4.843 22 114,00 4.488 54,00 2.126 63,00 2.480 68,00 2.677 80,00 3.150 59,00 2.323 120,00 4.724 92,00 3.622 123,00 4.843 24 109,00 4.291 54,00 2.126 60,00 2.362 68,00 2.677 80,00 3.150 59,00 2.323 107,00 4.213 95,00 3.740 123,00 4.843 28 119,00 4.685 54,00 2.126 63,00 2.480 67,00 2.638 81,00 3.189 59,00 2.323 107,00 4.213 95,00 3.740 124,00 4.882 32 115,00 4.528 54,00 2.126 61,00 2.402 67,00 2.638 80,00 3.189 58,00 2.283 106,00 4.173 100,00 3.937 120,00 4.724 36 112,00 4.409 54,00 2.126 67,00 2.638 68,00 2.677 80,00 3.189 58,00 2.283 106,00 4.173 107,00 4.213 117,00 4.606 40 N/A 54,00 2.126 68,00 2.677 68,00 2.677 80,00 3.189 58,00 2.283 103,00 4.055 107,00 4.213 114,00 4.488 * Please consult TE for availability. PAGE 34 CIRH ‘01’ STYLE CONNECTOR & ACCESSORY CONT. P R CIRH01M CIRH01R S CIRH01RC T U CIRH01XLA CIRH01XLC Metric Imperial Shell Size P R S T U 10SL 53,00 2.087 51,00 2.008 82,00 3.228 140,00 5.512 101,00 3.976 14S 56,00 2.205 51,00 2.008 82,00 3.228 137,00 5.394 101,00 3.976 16S 56,00 2.205 51,00 2.008 82,00 3.228 134,00 5.276 101,00 3.976 16 56,00 2.205 60,00 2.362 91,00 3.583 152,00 5.984 121,00 4.764 18 63,00 2.480 66,00 2.598 99,00 3.898 148,00 5.827 121,00 4.764 20 66,00 2.598 66,00 2.598 99,00 3.898 145,00 5.709 121,00 4.764 22 66,00 2.598 66,00 2.598 99,00 3.898 145,00 5.709 121,00 4.764 24 66,00 2.598 69,00 2.716 105,00 4.134 142,00 5.591 124,00 4.882 28 66,00 2.598 70,00 2.756 106,00 4.173 149,00 5.866 131,00 5.157 32 66,00 2.598 69,00 2.716 111,00 4.370 146,00 5.748 137,00 5.394 36 66,00 2.598 69,00 2.716 117,00 4.606 143,00 5.630 144,00 5.669 40 66,00 2.598 70,00 2.756 112,00 4.409 140,00 5.512 144,00 5.669 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR SQUARE FLANGE RECEPTACLE REAR MOUNTING (NO ACCESSORY THREAD) STYLE: CIRH03A/CIRH03A...M6 4 Tapped holes d2 (M6 MOD.) H B Om E 4 Holes ød1 C øM C P (max. panel thickness when using accessory) Metric Imperial Note: Maximum panel thickness when using cap head screws. When using countersunk screws, maximum panel thickness = 7.5 mm. See page 90 for panel mounting details. Shell Size B Max C Max d1 +0,2 -0 +0.008-0 d2 Thread E Max M Max H Max P See Note Om Min Overlap Mated 10SL 18,60 0.732 25,70 1.012 3,20 0.126 M4 0,7-6H 3,00 0.118 16,10 0.634 25,00 0.99 3,30 0.130 11,10 0.437 14S 18,60 0.732 30,30 1.193 3,20 0.126 M4 0,7-6H 3,40 0.134 19,20 0.756 25,00 0.99 3,30 0.130 11,10 0.437 16S 18,60 0.732 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 22,40 0.882 25,00 0.99 3,30 0.130 11,10 0.437 16 21,90 0.862 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 22,40 0.882 32,70 1.28 3,30 0.130 15,85 0.624 18 23,45 0.923 35,30 1.390 3,20 0.126 M4 0,7-6H 4,20 0.165 25,60 1.008 32,70 1.28 3,30 0.130 15,85 0.624 20 23,45 0.923 38,30 1.508 3,20 0.126 M4 0,7-6H 4,20 0.165 29,00 1.142 33,40 1.32 3,30 0.130 15,85 0.624 22 23,45 0.923 41,30 1.626 3,20 0.126 M4 0,7-6H 4,20 0.165 31,90 1.250 33,40 1.32 3,30 0.130 15,75 0.620 24 23,45 0.923 44,80 1.764 3,70 0.146 M4 0,7-6H 4,20 0.165 35,00 1.380 32,75 1.29 3,30 0.130 15,75 0.620 28 24,45 0.963 51,10 2.012 3,70 0.146 M5 0,8-6H 4,20 0.165 41,40 1.630 35,80 1.41 3,30 0.130 15,75 0.620 32 24,45 0.963 57,30 2.256 4,30 0.169 M5 0,8-6H 4,20 0.165 47,80 1.882 36,80 1.45 3,30 0.130 15,75 0.620 36 24,45 0.963 63,80 2.512 4,30 0.169 M5 0,8-6H 4,20 0.165 52,60 2.071 36,80 1.45 3,30 0.130 15,75 0.620 40 24,45 0.963 70,20 2.764 4,30 0.169 M5 0,8-6H 4,20 0.165 59,00 2.323 36,80 1.45 3,30 0.130 15,75 0.620 PAGE 36 SQUARE FLANGE RECEPTACLE WITH PCB CONTACTS REAR MOUNTING (NO ACCESSORY THREAD) STYLE: CIRH03APC#/CIRH03APC#...M6 Q P R (MAX. PANEL THICKNESS) ØX 4 HOLES Ød1 ØM C 4 TAPPED HOLES d2 (M6 MOD CODE) SCRAP VIEW Om C E B H Metric Imperial Note: Maximum panel thickness when using cap head screws. When using countersunk screws, maximum panel thickness = 7.5 mm. See page 90 for panel mounting details. Shell Size B Max C Max d1 +0,2 -0 +0.008-0 d2 Thread E Max M Max H Max P See Note Om Min Overlap Mated 10SL 18,60 0.732 25,70 1.012 3,20 0.126 M4 0,7-6H 3,00 0.118 16,10 0.634 25,00 0.990 3,30 0.130 11,10 0.437 14S 18,60 0.732 30,30 1.193 3,20 0.126 M4 0,7-6H 3,40 0.134 19,20 0.756 25,00 0.990 3,30 0.130 11,10 0.437 16S 18,60 0.732 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 22,40 0.882 25,00 0.990 3,30 0.130 11,10 0.437 16 21,90 0.862 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 22,40 0.882 32,70 1.280 3,30 0.130 15,85 0.624 18 23,45 0.923 35,30 1.390 3,20 0.126 M4 0,7-6H 4,20 0.165 25.60 1.008 32,70 1.280 3,30 0.130 15,85 0.624 20 23,45 0.923 38,30 1.508 3,20 0.126 M4 0,7-6H 4,20 0.165 29.00 1.142 33.40 1.320 3,30 0.130 15,85 0.624 22 23,45 0.923 41,30 1.626 3,20 0.126 M4 0,7-6H 4,20 0.165 31.90 1.250 33.40 1.320 3,30 0.130 15,75 0.620 24 23,45 0.923 44,80 1.764 3,70 0.146 M4 0,7-6H 4,20 0.165 35.00 1.380 32.75 1.290 3,30 0.130 15,75 0.620 28 24,45 0.963 51,10 2.012 3,70 0.146 M5 0,8-6H 4,20 0.165 41.40 1.630 35.80 1.410 3,30 0.130 15,75 0.620 32 24,45 0.963 57,30 2.256 4,30 0.169 M5 0,8-6H 4,20 0.165 37,0 1.46 36.80 1.450 3,30 0.130 15,75 0.620 36 24,45 0.963 63,80 2.512 4,30 0.169 M5 0,8-6H 4,20 0.165 37,0 1.46 36.80 1.450 3,30 0.130 15,75 0.620 40 24,45 0.963 70,20 2.764 4,30 0.169 M5 0,8-6H 4,20 0.165 38,0 1.50 36.80 1.450 3,30 0.130 15,75 0.620 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR PC TAIL CODE TABLE PC CODE Q ±0.88 R ±0.10 ØX Max A 25,00 0.984 5,00 0.197 0,75 0.030 C 12,70 0.500 7,00 0.276 0,75 0.030 F* 15,00 0.591 4,50 0.177 0,75 0.030 *1) Use PC code F for standard tail length. 2) Other PC tails available - please add detail to chart above and consult TE SQUARE FLANGE RECEPTACLE REAR MOUNTING (WITH ACCESSORY THREAD) STYLE: CIRH03T/CIRH03T...M6 4 Tapped holes d2 (M6 MOD.) H B Om E 4 Holes ød1 C øF C P (max. panel thickness when using accessory) Metric Imperial Note: Maximum panel thickness when using cap head screws. When using countersunk screws, maximum panel thickness = 7.5 mm. See page 90 for panel mounting details. Shell Size B Max C Max d1 +0,2 -0 +0.008-0 d2 Thread E Max F Thread Dia. Class 2A H Max P See Note Om Min Overlap Mated 10SL 18,60 0.732 25,70 1.012 3,20 0.126 M4 0,7-6H 3,00 0.118 5 /8" x 24 UNEF 30,0 1.19 3,30 0.130 11,10 0.437 14S 18,60 0.732 30,30 1.193 3,20 0.126 M4 0,7-6H 3,40 0.134 3 /4" x 20 UNEF 30,0 1.19 3,30 0.130 11,10 0.437 16S 18,60 0.732 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 7 /8" x 20 UNEF 30,0 1.19 3,30 0.130 11,10 0.437 16 21,90 0.862 32,80 1.291 3,20 0.126 M4 0,7-6H 3,40 0.134 7 /8" x 20 UNEF 37,0 1.46 3,30 0.130 15,85 0.624 18 23,45 0.923 35,30 1.390 3,20 0.126 M4 0,7-6H 4,20 0.165 1" x 20 UNEF 37,0 1.46 3,30 0.130 15,85 0.624 20 23,45 0.923 38,30 1.508 3,20 0.126 M4 0,7-6H 4,20 0.165 1 1/8" x 18 UNEF 37,0 1.46 3,30 0.130 15,85 0.624 22 23,45 0.923 41,30 1.626 3,20 0.126 M4 0,7-6H 4,20 0.165 1 1/4" x 18 UNEF 37,0 1.46 3,30 0.130 15,75 0.620 24 23,45 0.923 44,80 1.764 3,70 0.146 M4 0,7-6H 4,20 0.165 1 3/8" x 18 UNEF 37,0 1.46 3,30 0.130 15,75 0.620 28 24,45 0.963 51,10 2.012 3,70 0.146 M5 0,8-6H 4,20 0.165 1 5/8" x 18 UNEF 37,0 1.46 3,30 0.130 15,75 0.620 32 24,45 0.963 57,30 2.256 4,30 0.169 M5 0,8-6H 4,20 0.165 1 7/8" x 16 UN 37,0 1.46 3,30 0.130 15,75 0.620 36 24,45 0.963 63,80 2.512 4,30 0.169 M5 0,8-6H 4,20 0.165 2 1/16" x 16 UNS 37,0 1.46 3,30 0.130 15,75 0.620 40 24,45 0.963 70,20 2.764 4,30 0.169 M5 0,8-6H 4,20 0.165 2 5/16" x 16 UN 38,0 1.50 3,30 0.130 15,75 0.620 PAGE 38 CIRH ‘03’ STYLE CONNECTOR & ACCESSORY A B C CIRH03D CIRH03EV CIRH03F E D CIRH03FT CIRH03FC F CIRH03FM G H J CIRH03G CIRH03GM CIRH03GS Metric Imperial Shell Size A B C D E F G H J 10SL 109,00 4.291 44,00 1.732 58,00 2.283 58,00 2.283 55,00 2.165 55,00 2.165 50,00 1.968 54,00 2.126 * 14S 108,00 4.252 44,00 1.732 61,00 2.402 61,00 2.402 57,00 2.244 57,00 2.244 50,00 1.968 54,00 2.126 * 16S 105,00 4.134 44,00 1.732 65,00 2.559 65,00 2.559 61,00 2.402 61,00 2.402 50,00 1.968 54,00 2.126 * 16 117,00 4.606 60,00 2.362 77,00 3.031 77,00 3.031 73,00 2.874 73,00 2.874 63,00 2.480 70,00 2.756 * 18 121,00 4.764 60,00 2.362 82,00 3.228 82,00 3.228 78,00 3.071 78,00 3.071 65,00 2.559 70,00 2.756 80,00 3.150 20 120,00 4.724 60,00 2.362 87,00 3.425 88,00 3.465 83,00 3.268 83,00 3.268 66,00 2.598 74,00 2.913 86,00 3.386 22 120,00 4.724 60,00 2.362 87,00 3.425 88,00 3.465 83,00 3.268 83,00 3.268 68,00 2.677 74,00 2.913 86,00 3.386 24 114,00 4.488 60,00 2.362 95,00 3.740 95,00 3.740 91,00 3.583 91,00 3.583 66,00 2.598 74,00 2.913 86,00 3.386 28 124,00 4.882 60,00 2.362 94,00 3.700 94,00 3.700 90,00 3.543 90,00 3.543 68,00 2.677 73,00 2.874 87,00 3.425 32 121,00 4.764 60,00 2.362 104,00 4.094 107,00 4.213 100,00 3.937 100,00 3.937 67,00 2.638 73,00 2.874 86,00 3.386 36 118,00 4.646 60,00 2.362 110,00 4.331 111,00 4.370 106,00 4.173 106,00 4.173 72,00 2.835 74,00 2.913 88,00 3.465 40 NA 60,00 2.362 117,00 4.606 117,00 4.606 113,00 4.449 113,00 4.449 74,00 2.913 74,00 2.913 88,00 3.465 * Please consult TE for availability. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CIRH ‘03’ STYLE CONNECTOR & ACCESSORY CONT. L M CIRH03HC CIRH03HD K CIRH03H N CIRH03JE P R CIRH03M CIRH03R S CIRH03RC T U CIRH03XLA CIRH03XLC Metric Imperial Shell Size K L M N P R S T U 10SL 50,00 1.969 123,00 4.843 81,00 3.189 122,00 4.803 54,00 2.126 52,00 2.047 83,00 3.268 141,00 5.551 102,00 4.016 14S 50,00 1.969 119,00 4.685 81,00 3.189 118,00 4.646 56,00 2.205 52,00 2.047 83,00 3.268 138,00 5.433 102,00 4.016 16S 50,00 1.969 121,00 4.764 81,00 3.189 115,00 4.528 56,00 2.205 52,00 2.047 83,00 3.268 135,00 5.315 102,00 4.016 16 63,00 2.480 129,00 5.079 94,00 3.700 129,00 5.079 69,00 2.716 66,00 2.598 97,00 3.819 157,00 6.181 126,00 4.961 18 65,00 2.559 130,00 5.118 97,00 3.819 132,00 5.197 72,00 2.835 72,00 2.835 104,00 4.094 154,00 6.063 126,00 4.961 20 65,00 2.559 126,00 4.961 97,00 3.819 129,00 5.079 72,00 2.835 72,00 2.835 104,00 4.094 151,00 5.945 126,00 4.961 22 65,00 2.559 126,00 4.961 97,00 3.819 129,00 5.079 72,00 2.835 72,00 2.835 104,00 4.094 151,00 5.945 126,00 4.961 24 65,00 2.559 113,00 4.449 101,00 3.976 129,00 5.079 72,00 2.835 75,00 2.593 110,00 4.331 148,00 5.827 130,00 5.118 28 65,00 2.559 113,00 4.449 101,00 3.976 130,00 5.118 71,00 2.795 76,00 2.992 111,00 4.370 155,00 6.102 137,00 5.394 32 64,00 2.520 112,00 4.409 106,00 4.173 125,00 4.921 71,00 2.795 75,00 2.593 117,00 4.606 152,00 5.984 143,00 5.630 36 64,00 2.520 112,00 4.409 112,00 4.409 122,00 4.803 71,00 2.795 75,00 2.593 123,00 4.842 148,00 5.827 149,00 5.866 40 64,00 2.520 109,00 4.291 112,00 4.409 120,00 4.724 71,00 2.795 76,00 2.992 118,00 4.646 145,00 5.709 149,00 5.866 PAGE 40 SIZE 49 SQUARE FLANGE FRONT MOUNTING RECEPTACLE NO ACCESSORY OR WITH GROMMET & GROMMET NUT STYLES: CIRH04T OR CIRH04EV Metric Imperial See page 90 for panel mounting details CIRH04T Shell Size B C D1 +0,2 -0 +0.008-0 E F Thread Dia. Class 2A G Dia. H X 49 56,50 2.224 110,00 4.330 8,50 0.335 8,00 0.315 2 7/8" x 16 UN 90,00 3.543 62,50 2.460 90,00 3.543 Metric Imperial See page 90 for panel mounting details CIRH04EV Shell Size B C D1 +0,2 -0 +0.008-0 E G Dia. H X 49 56,50 2.224 110,00 4.330 8,50 0.335 8,00 0.315 90,00 3.543 81,50 3.209 90,00 3.543 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR SIZE 49 SQUARE FLANGE REAR MOUNTING RECEPTACLE NO ACCESSORY OR WITH GROMMET & GROMMET NUT STYLES: CIRH05T OR CIRH05EV Metric Imperial CIRH05T See page 90 for panel mounting details Shell Size B C D1 +0,2 -0 +0.008-0 E F Thread Dia. Class 2A G Dia. H P X 49 56,50 2.224 110,00 4.330 8,50 0.335 8,00 0.315 2 7/8" x 16 UN 90,00 3.543 62,50 2.460 15,00 0.590 90,00 3.543 Metric Imperial CIRH05EV See page 90 for panel mounting details Shell Size B C D1 +0,2 -0 +0.008-0 E G Dia. H P X 49 56,50 2.224 110,00 4.330 8,50 0.335 8,00 0.315 90,00 3.543 62,50 2.460 15,00 0.590 90,00 3.543 PAGE 42 PLUG - FINE KNURL COUPLING NUT STYLE: CIRH06T/CIRHSE06T Om øC øF E H CIRHSE06T with Screening Facility Metric Imperial F Thread Dia. Class 2A H Max Om Min Overlap Mated /8" x 24 UNEF 28,95 1.140 11,10 0.437 /4" x 20 UNEF 28,95 1.140 11,10 0.437 /8" x 20 UNEF 28,95 1.140 11,10 0.437 /8" x 20 UNEF 36,40 1.433 15,85 0.624 24,00 0.945 1" x 20 UNEF 36,40 1.433 15,85 0.624 40,70 1.602 24,00 0.945 1 1/8" x 18 UNEF 36,40 1.433 15,85 0.624 22 44,20 1.740 24,00 0.945 1 1/4" x 18 UNEF 36,40 1.433 15,85 0.624 24 47,70 1.878 24,00 0.945 1 3/8" x 18 UNEF 36,40 1.433 15,75 0.620 28 54,50 2.146 24,00 0.945 1 5/8" x 18 UNEF 36,40 1.433 15,75 0.620 32 61,40 2.417 27,00 1.063 1 7/8" x 16 UN 36,40 1.433 15,75 0.620 36 68,00 2.677 27,00 1.063 2 1/16" x 16 UNS 36,40 1.433 15,75 0.620 40 74,00 2.913 27,00 1.063 2 5/16" x 16 UN 36,40 1.433 15,75 0.620 Shell Size C Max E Max 10SL 24,20 0.953 17,50 0.689 5 14S 30,60 1.205 17,50 0.689 3 16S 33,40 1.315 17,50 0.689 7 16 33,40 1.315 24,00 0.945 7 18 37,30 1.468 20 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CIRH ‘06’ OR ‘SE06’ STYLE CONNECTOR & ACCESSORY A B C CIRH06D CIRH06EV CIRH08F D E CIRH08FC CIRH08FT F CIRH08FM G H J CIRH06G CIRH06GM CIRH06GS Metric Imperial Shell Size A B C D E F G H J 10SL 109,00 4.291 44,00 1.732 57,00 2.244 58,00 2.283 54,00 2.126 54,00 2.126 50,00 1.969 54,00 2.126 * 14S 107,00 4.213 44,00 1.732 61,00 2.402 60,00 2.362 56,00 2.205 57,00 2.244 50,00 1.969 54,00 2.126 * 16S 104,00 4.094 44,00 1.732 64,00 2.520 64,00 2.520 60,00 2.362 60,00 2.362 50,00 1.969 54,00 2.126 * 16 111,00 4.370 54,00 2.126 71,00 2.795 71,00 2.795 68,00 2.677 68,00 2.677 57,00 2.244 65,00 2.559 * 18 115,00 4.528 54,00 2.126 76,00 2.992 76,00 2.992 72,00 2.835 72,00 2.835 59,00 2.323 65,00 2.559 74,00 2.913 20 114,00 4.488 54,00 2.126 81,00 3.190 82,00 3.228 77,00 3.031 78,00 3.071 60,00 2.362 68,00 2.677 80,00 3.150 22 114,00 4.488 54,00 2.126 81,00 3.190 119,00 4.685 78,00 3.071 78,00 3.071 63,00 2.480 68,00 2.677 80,00 3.150 24 109,00 4.291 54,00 2.126 89,00 3.504 90,00 3.543 86,00 3.386 86,00 3.386 60,00 2.362 68,00 2.677 80,00 3.150 28 119,00 4.685 54,00 2.126 88,00 3.465 89,00 3.504 85,00 3.346 85,00 3.346 63,00 2.480 67,00 2.638 81,00 3.189 32 116,00 4.567 54,00 2.126 98,00 3.858 101,00 3.976 95,00 3.740 95,00 3.740 62,00 2.441 67,00 2.638 80,00 3.150 36 112,00 4.409 54,00 2.126 104,00 4.094 105,00 4.134 101,00 3.976 101,00 3.976 67,00 2.638 68,00 2.677 80,00 3.150 40 N/A 54,00 2.126 111,00 4.370 112,00 4.409 107,00 4.213 107,00 4.213 68,00 2.677 68,00 2.677 80,00 3.150 * Please consult TE for availability. PAGE 44 CIRH ‘06’ OR ‘SE06’ STYLE CONNECTOR & ACCESSORY CONT. L M CIRH06HC CIRH06HD K N CIRH06JE P R CIRH06M CIRH06R S CIRH06RC T U CIRH06XLA CIRH06XLC Metric Imperial Shell Size K L M N P R S T U 10SL 50,00 1.969 122,00 4.803 81,00 3.189 121,00 4.764 53,00 2.087 51,00 2.008 82,00 3.228 140,00 5.512 101,00 3.976 14S 50,00 1.969 119,00 4.685 81,00 3.189 118,00 4.646 56,00 2.205 51,00 2.008 82,00 3.228 137,00 5.394 101,00 3.976 16S 50,00 1.969 120,00 4.724 81,00 3.189 115,00 4.528 56,00 2.205 51,00 2.008 82,00 3.228 134,00 5.276 101,00 3.976 16 57,00 2.244 123,00 4.843 88,00 3.465 124,00 4.882 63,00 2.480 60,00 2.362 91,00 3.583 152,00 5.984 121,00 4.764 18 59,00 2.323 124,00 4.882 92,00 3.622 127,00 5.000 66,00 2.598 66,00 2.598 99,00 3.898 149,00 5.866 121,00 4.764 20 59,00 2.323 120,00 4.724 92,00 3.622 123,00 4.843 66,00 2.598 66,00 2.598 99,00 3.898 145,00 5.709 121,00 4.764 22 59,00 2.323 120,00 4.724 92,00 3.622 123,00 4.843 66,00 2.598 66,00 2.598 99,00 3.898 145,00 5.709 121,00 4.764 24 59,00 2.323 107,00 4.213 95,00 3.740 123,00 4.843 66,00 2.598 69,00 2.717 105,00 4.134 142,00 5.591 124,00 4.882 28 59,00 2.323 107,00 4.213 95,00 3.740 124,00 4.882 65,00 2.559 70,00 2.756 106,00 4.173 149,00 5.866 131,00 5.157 32 58,00 2.283 106,00 4.173 100,00 3.937 120,00 4.724 65,00 2.559 69,00 2.717 111,00 4.370 146,00 5.748 137,00 5.394 36 58,00 2.283 106,00 4.173 107,00 4.213 117,00 4.606 65,00 2.559 69,00 2.717 117,00 4.606 143,00 5.630 144,00 5.669 40 58,00 2.283 103,00 4.055 107,00 4.213 114,00 4.488 65,00 2.559 70,00 2.756 112,00 4.409 140,00 5.512 144,00 5.669 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR PLUG RUBBER COVERED COUPLING NUT STYLE: CIRHP06T/CIRHPSE06T Om ØB ØF Thread C E H Metric Imperial F Thread Dia. Class 2A H Max Om Min Overlap Mated /8 " x 24 UNEF 29,55 1.163 13,10 0.516 /4" x 20 UNEF 29,55 1.163 13,10 0.516 /8" x 20 UNEF 29,55 1.163 13,10 0.516 /8" x 20 UNEF 37,07 1.459 17,85 0.703 27,10 1.067 1" x 20 UNEF 37,07 1.459 17,85 0.703 46,00 1.811 27,10 1.067 1 1/8" x 18 UNEF 37,07 1.459 17,85 0.703 56,00 2.205 50,50 1.988 27,10 1.067 1 1/4" x 18 UNEF 37,07 1.459 17,85 0.703 24 60,00 2.362 54,00 2.126 27,10 1.067 1 3/8" x 18 UNEF 37,07 1.459 17,75 0.669 *28 67,00 2.638 61,00 2.402 27,10 1.067 1 5/8" x 18 UNEF 37,07 1.459 17,75 0.669 *32 76,00 2.992 67,60 2.661 27,10 1.067 1 7/8" x 16 UN 37,07 1.459 17,75 0.669 36 82,30 3.240 74,30 2.925 27,10 1.067 2 1/16" x 16 UNS 37,07 1.459 17,75 0.669 40 88,00 3.465 80,00 3.150 27,10 1.067 2 5/16" x 16 UN 37,07 1.459 17,75 0.669 Shell Size B Max C Max E Max *10SL 33,50 1.319 28,50 1.122 19,40 0.764 5 *14S 40,20 1.583 35,20 1.386 19,40 0.764 3 *16S 43,88 1.726 38,90 1.531 19,40 0.764 7 *16 43,88 1.726 38,90 1.531 27,10 1.067 7 18 49,00 1.929 43,50 1.713 20 51,50 2.026 22 * Please consult TE for availability. PAGE 46 CIRH ‘06’ OR ‘SE06’ STYLE CONNECTOR & ACCESSORY A B C CIRHP06D CIRHP06EV CIRHP08F D E CIRHP08FC CIRHP08FT F CIRHP08FM G J CIRHP06G CIRHP06GS Metric Imperial Shell Size A B C D E F G J *10SL 109,00 4.291 44,00 1.732 58,00 2.283 58,00 2.283 55,00 2.165 55,00 2.165 50,00 1.969 * *14S 108,00 4.252 44,00 1.732 61,00 2.402 61,00 2.402 57,00 2.244 57,00 2.244 50,00 1.969 * *16S 105,00 4.134 44,00 1.732 65,00 2.559 65,00 2.559 61,00 2.402 61,00 2.402 50,00 1.969 * *16 112,00 4.409 55,00 2.165 72,00 2.835 72,00 2.835 68,00 2.677 68,00 2.677 58,00 2.283 * 18 116,00 4.567 55,00 2.165 77,00 3.031 77,00 3.031 73,00 2.874 73,00 2.874 60,00 2.362 75,00 2.953 20 115,00 4.528 55,00 2.165 82,00 3.228 83,00 3.268 78,00 3.071 78,00 3.071 61,00 2.402 81,00 3.189 22 115,00 4.528 55,00 2.165 82,00 3.228 83,00 3.268 78,00 3.071 78,00 3.071 64,00 2.520 81,00 3.189 24 109,00 4.291 55,00 2.165 90,00 3.543 90,00 3.543 86,00 3.386 86,00 3.386 61,00 2.402 81,00 3.189 *28 119,00 4.685 55,00 2.165 89,00 3.504 89,00 3.504 85,00 3.346 85,00 3.346 64,00 2.520 82,00 3.228 *32 116,00 4.567 55,00 2.165 99,00 3.898 102,00 4.016 95,00 3.740 95,00 3.740 62,00 2.441 81,00 3.189 36 113,00 4.449 55,00 2.165 105,00 4.134 106,00 4.173 101,00 3.976 101,00 3.976 67,00 2.638 81,00 3.189 40 NA 55,00 2.165 112,00 4.409 112,00 4.409 108,00 4.252 108,00 4.252 69,00 2.717 81,00 3.189 * Please consult TE for availability. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CIRH ‘06’ OR ‘SE06’ STYLE CONNECTOR & ACCESSORY CONT. K L M CIRHP06H CIRHP06HC CIRHP06HD N CIRHP06JE R T CIRHP06R CIRHP06XLA S CIRHP06RC U CIRHP06XLC Metric Imperial Shell Size K L M N R S T U *10SL 51,00 2.008 123,00 4.843 81,00 3.189 122,00 4.803 52,00 2.047 83,00 3.268 140,00 5.512 102,00 4.016 *14S 51,00 2.008 119,00 4.685 81,00 3.189 119,00 4.685 52,00 2.047 83,00 3.268 138,00 5.433 102,00 4.016 *16S 51,00 2.008 121,00 4.764 81,00 3.189 115,00 4.528 52,00 2.047 83,00 3.268 135,00 5.315 102,00 4.016 *16 58,00 2.283 124,00 4.882 89,00 3.504 124,00 4.882 61,00 2.402 92,00 3.622 152,00 5.984 121,00 4.764 18 60,00 2.362 125,00 4.921 93,00 3.661 127,00 5.000 67,00 2.638 99,00 3.898 149,00 5.866 121,00 4.764 20 60,00 2.362 121,00 4.764 93,00 3.661 124,00 4.882 67,00 2.638 99,00 3.898 146,00 5.748 121,00 4.764 22 60,00 2.362 121,00 4.764 93,00 3.661 124,00 4.882 67,00 2.638 99,00 3.898 146,00 5.748 121,00 4.764 24 60,00 2.362 108,00 4.252 96,00 3.780 124,00 4.882 70,00 2.756 106,00 4.173 143,00 5.630 125,00 4.921 *28 60,00 2.362 108,00 4.252 96,00 3.780 125,00 4.921 71,00 2.795 106,00 4.173 150,00 5.906 132,00 5.197 *32 59,00 2.323 107,00 4.213 101,00 3.976 121,00 4.764 70,00 2.756 112,00 4.409 147,00 5.787 138,00 5.433 36 59,00 2.323 107,00 4.213 107,00 4.213 117,00 4.606 70,00 2.756 118,00 4.646 144,00 5.669 144,00 5.669 40 59,00 2.323 104,00 4.094 107,00 4.213 116,00 4.567 71,00 2.795 113,00 4.449 140,00 5.512 144,00 5.669 * Please consult TE for availability. PAGE 48 SIZE 49 PLUG WITH CONDUIT ADAPTOR RUBBER COVERED COUPLING NUT STYLE: CIRHP06GGL OR GGS 172.00 109.50 Dia. A Dia. B Thd. 74.50 A/F 12.00 Metric Imperial Connector Style A Dia. Max. B Thread CIRHP06GGL....... 43,50 1.713 2 1/4" x 16 UN-2A CIRHP06GGS........ 29,00 1.142 1 3/4" x 18 UNEF-2A RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR THROUGH BULKHEAD RECEPTACLE STYLE: CIRH07/CIRH07...M6 P (Max. Panel Thickness) 4 Holes Ø d1 C Pin side Socket side 4 Tapped Holes d2 (M6 MOD.) Om C Metric Imperial B Om E A Note. Maximum panel thickness when using cap head screws. When using countersunk screws, maximum panel thickness = 7.5 mm. See page 90 for panel mounting details. Shell Size A Max B Max C Max d1 +0,2 -0 +0.008-0 d2 Thread E Max P See Note Om Min Overlap Mated 10SL 38,20 1.504 17,60 0.693 25,70 1.012 3,20 0.126 M4 3,00 0.118 3,30 0.130 11,10 0.437 14S 38,20 1.504 18,00 0.709 30,30 1.193 3,20 0.126 M4 3,40 0.134 3,30 0.130 11,10 0.437 16S 38,20 1.504 18,00 0.709 32,80 1.291 3,20 0.126 M4 3,40 0.134 3,30 0.130 11,10 0.437 16 52,10 2.051 22,80 0.898 32,80 1.291 3,20 0.126 M4 3,40 0.134 3,30 0.130 15,85 0.624 18 52,10 2.051 23,60 0.929 35,30 1.390 3,20 0.126 M4 4,20 0.165 3,30 0.130 15,85 0.624 20 52,10 2.051 23,60 0.929 38,30 1.508 3,20 0.126 M4 4,20 0.165 3,30 0.130 15,85 0.624 22 52,10 2.051 23,60 0.929 41,30 1.626 3,20 0.126 M4 4,20 0.165 3,30 0.130 15,75 0.620 24 52,10 2.051 25,20 0.992 44,80 1.764 3,70 0.146 M4 4,20 0.165 3,30 0.130 15,75 0.620 28 52,10 2.051 25,20 0.992 51,10 2.012 3,70 0.146 M5 4,20 0.165 3,30 0.130 15,75 0.620 32 52,10 2.051 26,80 1.055 57,30 2.256 4,30 0.169 M5 4,20 0.165 3,30 0.130 15,75 0.620 36 52,10 2.051 26,80 1.055 63,80 2.512 4,30 0.169 M5 4,20 0.165 3,30 0.130 15,75 0.620 40 52,10 2.051 26,80 1.055 70,20 2.764 4,30 0.169 M5 4,20 0.165 3,30 0.130 15,75 0.620 PAGE 50 SINGLE HOLE MOUNTING RECEPTACLE REAR MOUNTED (NO ACCESSORY THREAD) STYLE: CIRH09A D C B G 0m G D E P Panel Thickness Metric Imperial See page 91 for panel mounting details. Shell Size B C D Max E G Min Max Om Min Overlap Mated 10SL 24,50 0.965 4,00 0.157 32,05 1.262 27,00 1.063 11,20 0.441 2,40 0.094 5,20 0.205 11,10 0.437 14S 26,80 1.055 4,80 0.189 41,55 1.636 33,00 1.299 14,60 0.575 2,40 0.094 7,50 0.295 11,10 0.437 16S 26,80 1.055 4,80 0.189 44,65 1.758 38,10 1.500 15,70 0.618 2,40 0.094 7,50 0.295 11,10 0.437 16 32,10 1.264 4,80 0.189 44,65 1.758 38,10 1.500 15,70 0.618 2,40 0.094 7,50 0.295 15,85 0.624 18 33,70 1.327 4,80 0.189 47,85 1.884 39,70 1.563 16,80 0.661 2,40 0.094 9,00 0.354 15,85 0.624 20 33,70 1.327 4,80 0.189 51,05 2.034 44,00 1.732 18,00 0.709 2,40 0.094 9,00 0.354 15,85 0.624 22 33,70 1.327 4,80 0.189 54,45 2.144 46,00 1.811 20,20 0.795 2,40 0.094 9,10 0.358 15,75 0.620 24 33,70 1.327 4,80 0.189 57,45 2.262 50,80 2.000 20,20 0.795 2,40 0.094 9,10 0.358 15,75 0.620 28 35,20 1.386 5,60 0.220 63,75 2.510 55,00 2.165 22,50 0.886 2,40 0.094 8,50 0.335 15,75 0.620 32 35,20 1.386 5,60 0.220 70,05 2.758 62,00 2.441 24,70 0.972 2,40 0.094 8,50 0.335 15,75 0.620 36 35,20 1.386 5,60 0.220 76,45 3.010 71,00 2.795 26,90 1.059 2,40 0.094 8,30 0.327 15,75 0.620 40 35,20 1.386 5,60 0.220 83,75 3.297 75,00 2.953 29,60 1.165 2,40 0.094 8,30 0.327 15,75 0.620 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR P SINGLE HOLE MOUNTING RECEPTACLE REAR MOUNTED STYLE: CIRH09T A D C B G 0m G F Thread D E P Panel Thickness Metric Imperial See page 91 for panel mounting details. F Thread Dia. Class 2A G Min Max Om Min Overlap Mated /8" x 24 UNEF 11,20 0.441 2,40 0.094 5,20 0.205 11,10 0.437 /4" x 20 UNEF 14,60 0.575 2,40 0.094 7,50 0.295 11,10 0.437 /8" x 20 UNEF 15,70 0.618 2,40 0.094 7,50 0.295 11,10 0.437 /8" x 20 UNEF 15,70 0.618 2,40 0.094 7,50 0.295 15,85 0.624 39,70 1.563 1" x 20 UNEF 16,80 0.661 2,40 0.094 9,00 0.354 15,85 0.624 51,05 2.034 44,00 1.732 1 1/8" x 18 UNEF 18,00 0.709 2,40 0.094 9,00 0.354 15,85 0.624 4,80 0.189 54,45 2.144 46,00 1.811 1 1/4" x 18 UNEF 20,20 0.795 2,40 0.094 9,10 0.358 15,75 0.620 33,70 1.327 4,80 0.189 57,45 2.262 50,80 2.000 1 3/8" x 18 UNEF 20,20 0.795 2,40 0.094 9,10 0.358 15,75 0.620 52,15 2.053 35,20 1.386 5,60 0.220 63,75 2.510 55,00 2.165 1 5/8" x 18 UNEF 22,50 0.886 2,40 0.094 8,50 0.335 15,75 0.620 32 52,15 2.053 35,20 1.386 5,60 0.220 70,05 2.758 62,00 2.441 1 7/8" x 16 UN 24,70 0.972 2,40 0.094 8,50 0.335 15,75 0.620 36 52,15 2.053 35,20 1.386 5,60 0.220 76,45 3.010 71,00 2.795 2 1/16" x 16 UNS 26,90 1.059 2,40 0.094 8,30 0.327 15,75 0.620 40 52,15 2.053 35,20 1.386 5,60 0.220 83,75 3.297 75,00 2.953 2 5/16" x 16 UN 29,60 1.165 2,40 0.094 8,30 0.327 15,75 0.620 Shell Size A Max B C D Max E 10SL 36,45 1.435 24,50 0.965 4,00 0.157 32,05 1.262 27,00 1.063 5 14S 39,15 1.541 26,80 1.055 4,80 0.189 41,55 1.636 33,00 1.299 3 16S 39,15 1.541 26,80 1.055 4,80 0.189 44,65 1.758 38,10 1.500 7 16 48,75 1.919 32,10 1.264 4,80 0.189 44,65 1.758 38,10 1.500 7 18 49,55 1.951 33,70 1.327 4,80 0.189 47,85 1.884 20 49,55 1.951 33,70 1.327 4,80 0.189 22 49,55 1.951 33,70 1.327 24 49,55 1.951 28 P PAGE 52 CIRH ‘09’ STYLE CONNECTOR & ACCESSORY A CIRH09D B C CIRH09EV CIRH09F D E CIRH09FC CIRH09FT F CIRH09FM G H J CIRH09G CIRH09GM CIRH09GS Metric Imperial Shell Size A B ++C ++D ++E ++F ++G ++H J 10SL 116,00 4.567 51,00 2.008 65,00 2.560 65,00 2.560 61,00 2.402 61,00 2.402 57,00 2.244 61,00 2.402 * 14S 117,00 4.606 54,00 2.126 70,00 2.756 71,00 2.795 67,00 2.638 67,00 2.638 60,00 2.362 64,00 2.520 * 16S 114,00 4.488 54,00 2.126 72,00 2.835 74,00 2.913 70,00 2.756 70,00 2.756 60,00 2.362 64,00 2.520 * 16 124,00 4.882 67,00 2.638 84,00 3.307 83,00 3.268 78,00 3.071 80,00 3.150 69,00 2.717 77,00 3.031 * 18 128,00 5.040 68,00 2.677 89,00 3.504 89,00 3.504 85,00 3.346 85,00 3.346 72,00 2.835 78,00 3.071 88,00 3.465 20 127,00 5.000 68,00 2.677 94,00 3.700 95,00 3.740 91,00 3.583 91,00 3.583 73,00 2.875 82,00 3.228 93,00 3.661 22 127,00 5.000 68,00 2.677 94,00 3.700 96,00 3.780 91,00 3.583 91,00 3.583 76,00 2.992 82,00 3.228 94,00 3.700 24 122,00 4.803 68,00 2.677 102,00 4.016 103,00 4.055 99,00 3.898 99,00 3.898 73,00 2.875 82,00 3.228 94,00 3.700 28 135,00 5.315 70,00 2.756 104,00 4.094 105,00 4.134 101,00 3.976 101,00 3.976 79,00 3.110 83,00 3.268 97,00 3.700 32 131,00 5.157 70,00 2.756 114,00 4.488 117,00 4.606 111,00 4.370 111,00 4.370 77,00 3.031 83,00 3.268 96,00 3.780 36 128,00 5.040 70,00 2.756 120,00 4.724 121,00 4.764 117,00 4.606 117,00 4.606 83,00 3.268 84,00 3.307 96,00 3.780 40 NA 70,00 2.756 127,00 5.000 128,00 5.039 123,00 4.843 123,00 4.843 84,00 3.307 84,00 3.307 96,00 3.780 * Please consult TE for availability. ++ For connector with locking accessory, please refer to the Sales office. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CIRH ‘09’ STYLE CONNECTOR & ACCESSORY CONT. K CIRH09H L M CIRH09HC CIRH09HD N CIRH09JE P R CIRH09M CIRH09R S CIRH09RC T U CIRH09XLA CIRH09XLC Metric Imperial Shell Size ++K ++L ++M N ++P R S ++T ++U 10SL 57,00 2.244 130,00 5.118 88,00 3.465 130,00 5.118 61,00 2.402 59,00 2.323 90,00 3.543 148,00 5.827 109,00 4.291 14S 60,00 2.362 129,00 5.079 91,00 3.583 128,00 5.039 66,00 2.598 61,00 2.402 92,00 3.622 147,00 5.787 112,00 4.409 16S 60,00 2.362 131,00 5.157 91,00 3.583 125,00 4.921 66,00 2.598 61,00 2.402 92,00 3.622 144,00 5.669 112,00 4.409 16 72,00 2.835 135,00 5.315 101,00 3.976 136,00 5.354 76,00 2.992 72,00 2.835 103,00 4.055 134,00 5.276 133,00 5.236 18 73,00 2.875 138,00 5.433 105,00 4.134 140,00 5.512 80,00 3.150 79,00 3.110 112,00 4.409 162,00 6.378 134,00 5.276 20 73,00 2.875 133,00 5.236 105,00 4.134 137,00 5.394 80,00 3.150 79,00 3.110 112,00 4.409 159,00 6.260 134,00 5.276 22 73,00 2.875 133,00 5.236 105,00 4.134 137,00 5.394 80,00 3.150 79,00 3.110 112,00 4.409 159,00 6.260 134,00 5.276 24 73,00 2.875 120,00 4.724 108,00 4.252 137,00 5.394 80,00 3.150 79,00 3.110 112,00 4.409 159,00 6.260 134,00 5.276 28 75,00 2.953 123,00 4.843 112,00 4.409 140,00 5.512 81,00 3.189 86,00 3.386 121,00 4.764 165,00 6.496 147,00 5.787 32 74,00 2.913 122,00 4.803 116,00 4.567 136,00 5.354 81,00 3.189 85,00 3.346 127,00 5.000 162,00 6.378 153,00 6.024 36 74,00 2.913 122,00 4.803 122,00 4.803 133,00 5.236 81,00 3.189 85,00 3.346 133,00 5.236 159,00 6.260 159,00 6.260 40 74,00 2.913 119,00 4.685 123,00 4.843 131,00 5.157 81,00 3.189 86,00 3.386 128,00 5.039 155,00 6.102 159,00 6.260 ++ For connector with locking accessory, please refer to TE PAGE 54 PANEL MOUNTED PLUG (NO ACCESSORY THREAD) STYLE: CIRH12A/CIRH12A...M6 4 Tapped Holes Ød2 (M6 MOD.) Om C H C Metric Imperial E ØA 4 holes Ød1 Note: No provision for rear sealing - contact factory if required. See page 90 for panel mounting details. Shell Size A Max. C Max. d1 +0.2, -0 mm d2 Thread E Max. H Max. 0m Min. Overlap, mated 10SL 24,20 0.953 25,70 1.012 3.20 0.126 M4 3,00 0.118 28,10 1.106 11,10 0.437 14S 30,60 1.205 30,30 1.193 3.20 0.126 M4 3,40 0.134 28,10 1.106 11,10 0.437 16S 33,40 1.315 32,80 1.291 3.20 0.126 M4 3,40 0.134 28,10 1.106 11,10 0.437 16 33,40 1.315 32,80 1.291 3.20 0.126 M4 3,40 0.134 37,60 1.480 15,85 0.624 18 37,30 1.469 35,30 1.390 3.20 0.126 M4 4,20 0.165 38,60 1.519 15,85 0.624 20 40,70 1.602 38,30 1.508 3.20 0.126 M4 4,20 0.165 38,60 1.519 15,85 0.624 22 44,20 1.740 41,30 1.626 3.20 0.126 M4 4,20 0.165 38,60 1.519 15,85 0.624 24 47,70 1.878 44,80 1.764 3.20 0.126 M4 4,20 0.165 41,00 1.614 15,75 0.620 28 54,50 2.146 51,10 2.012 3.20 0.126 M5 4,20 0.165 41,80 1.646 15,75 0.620 32 61,40 2.417 57,30 2.256 4,30 0.169 M5 4,20 0.165 45,00 1.772 15,75 0.620 36 68,00 2.677 63,80 2.512 4,30 0.169 M5 4,20 0.165 45,00 1.772 15,75 0.620 40 74,00 2.913 70,20 2.764 4,30 0.169 M5 4,20 0.165 45,00 1.772 15,75 0.620 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CONDUIT ADAPTOR WITH BRAID SCREEN TRAP - NO GROMMET ACCESSORY TYPE ‘RM’ STYLE: CIRB - ** - CRA ØF Thread ØS ØM ØF1 Thread G ØT N How to order: Metric Imperial Note: This accessory can only be used in conjunction with style ‘H’ or ‘FT’ adaptor. Shell Size F Thread Dia. Class 2B CIRB - ** - CRA Shell size F1 Thread Dia. Class 2A G Max N Max S Min T Max M Max /4" x 20 UNEF 11,00 0.433 23.10 0.909 8,40 0.331 18,50 0.728 10.10 0.398 /8" x 20 UNEF 10,00 0.394 27,60 1.087 8,51 0.335 21,53 0.848 11,71 0.461 /8" x 20 UNEF 1" x 20 UNEF 10,00 0.394 27,60 1.087 9,74 0.383 25,50 1.004 13,10 0.516 /8" x 20 UNEF 1" x 20 UNEF 11,00 0.433 30,60 1.205 9,74 0.383 25,50 1.004 13,10 0.516 18 1" x 20 UNEF 1 2/16" x 18 UNEF 11,00 0.433 30,60 1.205 12,90 0.508 29,10 1.146 16,26 0.640 20 1 3/16" x 18 UNEF 1 7/16" x 18 UNEF 11,00 0.433 30,60 1.205 18,23 0.718 35,45 1.396 21,51 0.847 22 1 3/16" x 18 UNEF 1 7/16" x 18 UNEF 11,00 0.433 30,60 1.205 18,23 0.718 35,45 1.396 21,51 0.847 24 1 7/16" x 18 UNEF 1 3/4" x 18 UNS 11,00 0.433 30,60 1.205 25,93 1.021 43,60 1.717 29,21 1.150 28 1 7/16" x 18 UNEF 1 3/4" x 18 UNS 11,00 0.433 30,60 1.205 25,93 1.021 43,60 1.717 29,21 1.150 32 1 3/4" x 18 UNS 1 3/4" x 18 UNS 13,00 0.512 30,60 1.205 25,93 1.021 49,55 1.951 29,10 1.146 36 2" x 18 UNS 2" x 18 UNS 13,00 0.512 30,60 1.205 32,00 1.260 55,90 2.201 35,19 1.385 40 2 1/4" x 16 UN 2 1/4" x 16 UN 13,00 0.512 30,60 1.205 32,33 1.273 63,10 2.484 35,60 1.402 10SL 5 14S 3 16S 7 16 7 /8" x 24 UNEF 3 /4" x 20 UNEF 7 *Please consult TE for availability. PAGE 56 NON-LOCKING CABLE CLAMP WITH GROMMET & FOLLOWER ACCESSORY TYPE ‘D’ STYLE: CIRBH - ** - ** - OCN - F80 Oa ØT N2 N1 ØS ØF How to order: CIRBH - ** - ** - OCN- F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B N1 Max N2 Max S Min/Max T Max Oa Min Overlap Accessory /8" x 24 UNEF 36,42 1.434 86,68 3.413 3,68/5,76 0.145/0.227 35,15 1.384 7,00 0.276 /4" x 20 UNEF 27,41 1.079 85,04 3.348 4,62/8,10 0.182/0.319 39,88 1.570 7,00 0.276 /8" x 20 UNEF 27,41 1.079 81,99 3.228 7,82/11,30 0.308/0.444 41,45 1.632 7,00 0.276 /8" x 20 UNEF 27,41 1.079 81,99 3.228 7,82/11,30 0.308/0.444 41,45 1.632 7,00 0.276 18 1" x 20 UNEF 44,68 1.759 85,55 3.368 8,79/14,45 0.346/0.569 45,52 1.792 7,00 0.276 20 1 1/8" x 18 UNEF 44,68 1.759 84,61 3.331 10,54/16,00 0.415/0.632 49,63 1.954 7,00 0.276 22 1 1/4" x 18 UNEF 44,68 1.759 84,61 3.331 10,54/16,00 0.415/0.632 49,63 1.954 7,00 0.276 24 1 2/8" x 18 UNEF 44,68 1.759 79,20 3.118 14,55/19,23 0.573/0.757 56,29 2.216 7,00 0.276 28 1 5/8" x 18 UNEF 54,79 2.157 89,31 3.516 14,15/19,23 0.557/0.757 60,45 2.380 7,00 0.276 32 1 7/8" x 16 UN 54,79 2.157 86,13 3.390 19,18/23,98 0.755/0.944 68,43 2.694 7,00 0.276 36 2 1/16" x 16 UNS 54,79 2.157 82,98 3.267 24,51/31,93 0.965/1.257 71,68 2.822 7,00 0.276 Shell Size 10SL 5 14S 3 16S 7 16 7 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR NON-LOCKING GROMMET NUT TYPE ‘EV’ STYLE: CIRBH - ** - ** - EV - F80 Oa ØF ØT ØS N How to order: CIRBH - ** - ** - EV - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B N Max S Min Oa Min Overlap Accessory /8" x 24 UNEF 20,83 0.820 8,60 0.339 6,10 0.240 /4" x 20 UNEF 20,83 0.820 11,10 0.437 6,10 0.240 /8" x 20 UNEF 20,83 0.820 14,30 0.563 6,10 0.240 /8" x 20 UNEF 25,53 1.005 14,30 0.563 7,60 0.300 31,90 1.256 1" x 20 UNEF 25,53 1.005 16,70 0.657 7,60 0.300 20 34,90 1.374 1 1/8" x 18 UNEF 25,53 1.005 19,80 0.780 7,60 0.300 22 38,20 1.504 1 1/4" x 18 UNEF 25,53 1.005 21,34 0.840 7,60 0.300 24 41,40 1.630 1 3/8" x 18 UNEF 25,53 1.005 25,40 1.000 7,60 0.300 28 47,80 1.882 1 5/8" x 18 UNEF 25,53 1.005 30,13 1.186 7,60 0.300 32 54,10 2.130 1 7/8" x 16 UN 25,53 1.005 36,73 1.446 7,60 0.300 36 58,70 2.311 2 1/16" x 16 UNS 25,53 1.005 41,00 1.614 7,60 0.300 40 63.00 2.480 2 5/16" x 16 UN 25,64 1.009 45,90 1.807 7,60 0.300 Shell Size T Max 10SL 21,60 0.850 5 14S 24,80 0.976 3 16S 28,70 1.130 7 16 28,70 1.130 7 18 PAGE 58 LOCKING 90° OUTLET WITH CABLE CLAMP & BUSHING TYPE ‘F’ STYLE: CIRBH - ** - ** - F - F80 How to order: CIRBH - ** - ** - F - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B N Max T Max T1 Max S Max Oa Min Overlap Accessory /8" x 24 UNEF 42,00 1.654 22,00 0.866 22,70 0.894 5,76 0.227 7,00 0.276 /4" x 20 UNEF 42,00 1.654 25,00 0.984 27,50 1.083 8,10 0.319 7,00 0.276 /8" x 20 UNEF 45,00 1.772 28,00 1.102 30,00 1.181 11,30 0.444 7,00 0.276 /8" x 20 UNEF 45,00 1.772 28,00 1.102 30,00 1.181 11,30 0.444 7,00 0.276 100,00 3.937 1" x 20 UNEF 53,00 2.087 31,00 1.220 33,00 1.299 14,45 0.569 7,00 0.276 35,00 1.378 100,00 3.937 1 1/8" x 18 UNEF 53,00 2.087 35,00 1.378 37,50 1.476 16,00 0.632 7,00 0.276 33,10 1.303 35,00 1.378 100,00 3.937 1 1/4" x 18 UNEF 53,00 2.087 38,00 1.496 37,50 1.476 16,00 0.632 7,00 0.276 24 37,90 1.492 40,00 1.575 100,00 3.937 1 3/8" x 18 UNEF 58,00 2.283 41,00 1.614 43,30 1.705 19,23 0.757 7,00 0.276 28 37,10 1.461 40,00 1.575 100,00 3.937 1 5/8" x 18 UNEF 58,00 2.283 48,00 1.890 43,30 1.705 19,23 0.757 7,00 0.276 32 43,10 1.697 45,00 1.772 110,00 4.331 1 7/8" x 16 UN 66,00 2.598 54,00 2.126 51,70 2.035 23,98 0.944 7,00 0.276 36 45,90 1.807 50,00 1.969 110,00 4.331 2 1/16" x 16 UNS 69,00 2.717 61,00 2.402 58,00 2.283 31,93 1.257 7,00 0.276 40 49,00 1.929 54,60 2.150 100,00 3.937 2 5/16" x 16 UN 85,50 3.366 67,00 2.638 65,00 2.559 35,10 1.382 7,00 0.276 Shell Size B Max C Max C1 Max 10SL 24,00 0.945 30,00 1.181 100,00 3.937 5 14S 25,00 0.984 30,00 1.181 100,00 3.937 3 16S 27,00 1.063 30,00 1.181 100,00 3.937 7 16 27,00 1.063 30,00 1.181 100,00 3.937 7 18 30,10 1.224 35,00 1.378 20 33,00 1.299 22 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR LOCKING 90° OUTLET WITH SEALED CABLE CLAMP TYPE ‘FC’ STYLE: CIRBH - ** - ** - FC - F80 How to order: CIRBH - ** - ** - FC - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B T Max Oa Min Overlap Accessory /8" x 24 UNEF 22,00 0.866 7,00 0.276 /4" x 20 UNEF 25,00 0.984 7,00 0.276 /8" x 20 UNEF 28,00 1.102 7,00 0.276 /8" x 20 UNEF 28,00 1.102 7,00 0.276 68,00 2.677 1" x 20 UNEF 31,00 1.220 7,00 0.276 39,67 1.562 68,00 2.677 1 1/8" x 18 UNEF 35,00 1.378 7,00 0.276 33,10 1.303 39,67 1.562 68,00 2.677 1 1/4" x 18 UNEF 38,00 1.496 7,00 0.276 24 37,90 1.492 44,45 1.750 76,00 2.992 1 3/8" x 18 UNEF 41,00 1.614 7,00 0.276 28 37,10 1.461 44,45 1.750 76,00 2.992 1 5/8" x 18 UNEF 48,00 1.890 7,00 0.276 32 43,10 1.697 57,15 2.250 87,00 3.425 1 7/8" x 16 UN 54,00 2.126 7,00 0.276 36 45,90 1.807 60,33 2.375 98,00 3.858 2 1/16" x 16 UNS 61,00 2.402 7,00 0.276 40 49,00 1.929 66,68 2.625 103,00 4.055 2 5/16" x 16 UN 67,00 2.638 7,00 0.276 Shell Size B Max C Max D Max 10SL 24,00 0.945 23,80 0.937 61,00 2.402 5 14S 25,00 0.984 26,97 1.062 61,00 2.402 3 16S 27,00 1.063 30,18 1.188 61,00 2.402 7 16 27,00 1.063 30,18 1.188 61,00 2.402 7 18 30,10 1.224 33,32 1.312 20 33,00 1.299 22 PAGE 60 LOCKING 90° OUTLET WITH GROMMET ACCESSORY TYPE ‘FT’ STYLE: CIRBH - ** - ** - FT - F80 ØT B 0a ØF Thread C ØF1 How to order: CIRBH - ** - ** - FT - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B F1 Thread Dia. Class 2A T Max Oa Min Overlap Accessory /8" x 24 UNEF 22,00 0.866 7,00 0.276 /4" x 20 UNEF 25,00 0.984 7,00 0.276 /8" x 20 UNEF 28,00 1.102 7,00 0.276 /8" x 20 UNEF 28,00 1.102 7,00 0.276 1" x 20 UNEF 1" x 20 UNEF 31,00 1.220 7,00 0.276 35,00 1.378 1 1/8" x 18 UNEF 1 3/16" x 18 UNEF 35,00 1.378 7,00 0.276 33,10 1.303 35,00 1.378 1 1/4" x 18 UNEF 1 3/16" x 18 UNEF 38,00 1.496 7,00 0.276 24 37,90 1.492 40,00 1.575 1 3/8" x 18 UNEF 1 7/16" x 18 NEF 41,00 1.614 7,00 0.276 28 37,10 1.461 40,00 1.575 1 5/8" x 18 UNEF 1 7/16" x 18 NEF 48,00 1.890 7,00 0.276 32 43,10 1.697 45,00 1.772 1 7/8" x 16 UN 1 3/4" x 18 UNS 54,00 2.126 7,00 0.276 36 45,90 1.807 50,00 1.969 2 1/16" x 16 UNS 2" x 18 UNS 61,00 2.402 7,00 0.276 40 49,00 1.929 54,60 2.150 2 5/16" x 16 UN 2 1/4" x 16 UN 67,00 2.638 7,00 0.276 Shell Size B Max C Max 10SL 24,00 0.945 30,00 1.181 5 14S 25,00 0.984 30,00 1.181 3 16S 27,00 1.063 30,00 1.181 7 16 27,00 1.063 30,00 1.181 7 18 30,10 1.224 35,00 1.378 20 33,10 1.299 22 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR /8" x 24 UNEF 5 /4" x 20 UNEF 3 /8" x 20 UNEF 7 /8" x 20 UNEF 7 LOCKING 90° OUTLET RFI SHIELDED WITH GROMMET ACCESSORY TYPE ‘FM’ STYLE: CIRBH - ** - ** - FM - F80 B 0a ØF Thread C ØD ØT ØA How to order: CIRBH - ** - ** - FM - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B T Max Oa Min Overlap Accessory /8" x 24 UNEF 22,00 0.866 7,00 0.276 /4" x 20 UNEF 25,00 0.984 7,00 0.276 /8" x 20 UNEF 28,00 1.102 7,00 0.276 /8" x 20 UNEF 28,00 1.102 7,00 0.276 15,14 0.596 1" x 20 UNEF 31,00 1.220 7,00 0.276 35,00 1.378 18,10 0.713 1 1/8" x 18 UNEF 35,00 1.378 7,00 0.276 33,10 1.303 35,00 1.378 21,62 0.851 1 1/4" x 18 UNEF 38,00 1.496 7,00 0.276 36,60 1.441 37,90 1.492 40,00 1.575 25,10 0.988 1 3/8" x 18 UNEF 41,00 1.614 7,00 0.276 28 36,60 1.441 37,10 1.461 40,00 1.575 30,38 1.196 1 5/8" x 18 UNEF 48,00 1.890 7,00 0.276 32 44,50 1.752 43,10 1.697 45,00 1.772 36,48 1.436 1 7/8" x 16 UN 54,00 2.126 7,00 0.276 36 50,90 2.004 45,90 1.807 50,00 1.969 40,67 1.601 2 1/16" x 16 UNS 61,00 2.402 7,00 0.276 40 57,20 2.252 49,00 1.929 54,60 2.150 48,50 1.909 2 5/16" x 16 UN 67,00 2.638 7,00 0.276 Shell Size A Max B Max C Max D Max 10SL 15,90 0.626 24,00 0.945 30,00 1.181 7,77 0.306 5 14S 19,10 0.764 25,00 0.984 30,00 1.181 10,36 0.408 3 16S 22,30 0.878 27,00 1.063 30,00 1.181 13,01 0.512 7 16 22,30 0.878 27,00 1.063 30,00 1.181 13,01 0.512 7 18 25,50 1.004 30,10 1.224 35,00 1.378 20 30,20 1.189 33,00 1.299 22 30,20 1.189 24 PAGE 62 LOCKING HEATSHRINK ADAPTOR WITH GROMMET ACCESSORY TYPE ‘G’ STYLE: CIRBH - ** - ** - HSA - F80 Oa ØS ØF Thread ØT M G N How to order: CIRBH - ** - ** - HSA - F80 Shell size Contact arrangement Metric Imperial F Thread Dia. Class 2B G Max M Max N Max S Min T Max Oa Min Overlap Accessory /8" x 24 UNEF 8,20 0.323 15,70 0.618 28.46 1.120 7,70 0.303 22,00 0.87 7,00 0.276 /4" x 20 UNEF 8,20 0.323 19,30 0.760 28.46 1.120 10.60 0.417 25,00 0.99 7,00 0.276 /8" x 20 UNEF 8,20 0.323 24,10 0.949 28.46 1.120 13,50 0.532 28,00 1.11 7,00 0.276 /8" x 20 UNEF 8,00 0.315 24,10 0.949 32.26 1.270 13,50 0.532 28,00 1.11 7,00 0.276 18 1" x 20 UNEF 8,00 0.315 24,10 0.949 32.26 1.270 14,60 0.575 31,00 1.22 7,00 0.276 20 1 1/8" x 18 UNEF 9,20 0.362 29,80 1.173 35.80 1.409 18,70 0.736 35,00 1.38 7,00 0.276 22 1 1/4" x 18 UNEF 9,20 0.362 29,80 1.173 35.80 1.409 20,80 0.819 38,00 1.50 7,00 0.276 24 1 3/8" x 18 UNEF 9,20 0.362 38,00 1.496 35.80 1.409 24,60 0.969 41,00 1.62 7,00 0.276 28 1 5/8" x 18 UNEF 9,20 0.362 38,00 1.496 35.76 1.408 27,00 1.063 48,00 1.89 7,00 0.276 32 1 7/8" x 16 UN 11,70 0.461 48,00 1.890 38.26 1.506 33,30 1.311 54,00 2.13 7,00 0.276 36 2 1/16" x 16 UNS 11,70 0.461 48,00 1.890 39.26 1.546 38,50 1.516 61,00 2.40 7,00 0.276 40 2 5/16" x 16 UN 12,10 0.476 57,95 2.281 38.30 1.508 48,10 1.894 67,00 2.638 7,00 0.276 Shell Size 10SL 5 14S 3 16S 7 16 7 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR LOCKING RFI SHIELDED ADAPTOR WITH GROMMET ACCESSORY TYPE ‘GM’ STYLE: CIRBH - ** - ** - LHSA - F80 Oa ØF Thread ØS ØM G ØT N How to order: CIRBH - ** - ** - LHSA - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B G Max M Max N Max S Min T Max Oa Min Overlap Accessory /8" x 24 UNEF 12,40 0.488 15,70 0.618 32.26 1.270 8,60 0.339 22,00 0.87 7,00 0.276 /4" x 20 UNEF 12,40 0.488 19,30 0.760 32.26 1.270 11,10 0.437 25,00 0.984 7,00 0.276 /8" x 20 UNEF 12,40 0.488 24,10 0.949 32.26 1.270 14,30 0.563 28,00 1.102 7,00 0.276 /8" x 20 UNEF 12,40 0.488 24,10 0.949 36.06 1.420 14,30 0.563 28,00 1.102 7,00 0.276 18 1" x 20 UNEF 12,40 0.488 24,10 0.949 36.06 1.420 16,70 0.657 31,00 1.22 7,00 0.276 20 1 1/8" x 18 UNEF 12,40 0.488 29,80 1.173 38.60 1.520 19,80 0.780 35,00 1.38 7,00 0.276 22 1 1/4" x 18 UNEF 12,40 0.488 29,80 1.173 38.60 1.520 21,34 0.840 38,00 1.50 7,00 0.276 24 1 3/8" x 18 UNEF 12,40 0.488 38,00 1.496 38.60 1.520 25,40 1.000 41,00 1.62 7,00 0.276 28 1 5/8" x 18 UNEF 12,40 0.488 38,00 1.496 38.56 1.518 30,13 1.186 48,00 1.89 7,00 0.276 32 1 7/8" x 16 UN 12,10 0.476 48,00 1.890 38.26 1.506 36,73 1.446 54,00 2.13 7,00 0.276 36 2 1/16" x 16 UNS 12,10 0.476 48,00 1.890 39.26 1.546 41,00 1.614 61,00 2.40 7,00 0.276 40 2 5/16" x 16 UN 12,10 0.476 57,95 2.281 38.30 1.508 48,10 1.894 67,00 2.638 7,00 0.276 Shell Size 10SL 5 14S 3 16S 7 16 7 PAGE 64 NON-LOCKING HEATSHRINK ADAPTOR, GROMMET & FOLLOWER ACCESSORY TYPE ‘GS’ STYLE: CIRBH - ** - ** - HSAS - F80 Oa ØS ØF Thread ØT ØM G N How to order: CIRBH - ** - ** - HSAS - F80 Shell size Metric Imperial Contact arrangement Shell Size F Thread Dia. Class 2B M Max G Max N Max S Min T Max Oa Min Overlap Accessory *10SL - - - - - - - *14S - - - - - - - *16S - - - - - - - *16 - - - - - - - 18 1" x 20 UNEF 24,10 0.949 11,90 0.469 45,30 1.783 14,70 0.579 28,60 1.126 7,34 0.289 20 1 1/8" x 18 UNEF 29,80 1.173 11,90 0.469 51,10 2.012 18,70 0.736 31,85 1.254 7,34 0.289 22 1 1/4" x 18 UNEF 29,80 1.173 11,90 0.469 51,10 2.012 20,90 0.823 35,03 1.379 7,14 0.281 24 1 3/8" x 18 UNEF 38,00 1.496 11,90 0.469 51,10 2.012 24,70 0.972 39,10 1.539 7,14 0.281 28 1 5/8" x 18 UNEF 38,00 1.496 11,90 0.469 51,10 2.012 27,10 1.067 45,60 1.795 6,34 0.250 32 1 7/8" x 16 UN 48,00 1.890 11,90 0.469 51,10 2.012 33,40 1.315 50,80 2.000 7,40 0.291 36 2 1/16" x 16 UNS 48,00 1.890 11,90 0.469 51,10 2.012 38,60 1.520 57,45 2.262 7,40 0.291 40 2 5/16" x 16 UN 57,95 2.281 11,90 0.469 51,10 2.012 48,10 1.894 63,10 2.484 7,40 0.291 * Please consult TE for availability. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR LOCKING ARMOURED CONDUIT ADAPTOR WITH GROMMET ACCESSORY TYPE ‘H’ STYLE: CIRBH - ** - ** - ACA - F80 Oa ØS ØF Thread ØT ØF1 Thread G N How to order: CIRBH - ** - ** - ACA - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B Shell Size 10SL 5 14S 3 16S 7 16 7 F1 Thread Dia. Class 2A G Max N Max S Min T Max Oa Min Overlap Accessory /8" x 24 UNEF 9,50 0.374 27,90 1.098 8,20 0.323 22,00 0.87 7,00 0.276 /4" x 20 UNEF 9,50 0.374 27,90 1.098 11,10 0.437 25,00 0.99 7,00 0.276 /8" x 20 UNEF 9,50 0.374 27,90 1.098 14,30 0.563 28,00 1.11 7,00 0.276 /8" x 20 UNEF 9,50 0.374 27,90 1.098 14,30 0.563 28,00 1.11 7,00 0.276 /8" x 24 UNEF 5 /4" x 20 UNEF 3 /8" x 20 UNEF 7 /8" x 20 UNEF 7 18 1" x 20 UNEF 1" x 20 UNEF 9,50 0.374 29,90 1.177 16,70 0.657 31,00 1.22 7,00 0.276 20 1 1/8" x 18 UNEF 1 2/16" x 18 NEF 9,50 0.374 29,90 1.177 19,80 0.780 35,00 1.38 7,00 0.276 22 1 1/4" x 18 UNEF 1 3/16" x 18 NEF 9,50 0.374 29,90 1.177 19,80 0.780 38,00 1.50 7,00 0.276 24 1 3/8" x 18 UNEF 1 7/16" x 18 NEF 9,50 0.374 29,90 1.177 25,40 1.000 41,00 1.62 7,00 0.276 28 1 5/8" x 18 UNEF 1 7/16" x 18 NEF 9,50 0.374 30,00 1.181 27,00 1.063 48,00 1.89 7,00 0.276 32 1 7/8" x 16 UN 1 3/4" x 18 NS 11,00 0.433 28,90 1.138 32,50 1.280 54,00 2.13 7,00 0.276 36 2 1/16" x 16 UNS 2" x 18 NS 11,80 0.464 28,90 1.138 35,70 1.406 61,00 2.40 7,00 0.276 40 2 5/16" x 16 UN 2 1/4" x 16 UN 11,80 0.464 28,90 1.138 45,00 1.772 67,00 2.638 7,00 0.276 PAGE 66 LOCKING CABLE CLAMP WITH BUSHING TYPE ‘HC’ STYLE: CIRBH - ** - ** - HC - F80 N1 N2 Oa ØF Thread ØT ØS How to order: CIRBH - ** - ** - HC - F80 Shell size Metric Imperial Note: Clamp & bush are available separately. See pages 83 & 84 respectively. Contact arrangement F Thread Dia. Class 2B N1 Max N2 Max S T Max Oa Min Overlap Accessory /8" x 24 UNEF 40,10 1.58 100,10 3.94 5.59 0.220 22,70 0.90 7,00 0.276 /4" x 20 UNEF 41,70 1.65 96,70 3.81 7.92 0.312 27,50 1.09 7,00 0.276 /8" x 20 UNEF 43,50 1.72 98,50 3.88 11.10 0.437 30,00 1.19 7,00 0.276 /8" x 20 UNEF 43,50 1.72 93,50 3.68 11.10 0.437 30,00 1.19 7,00 0.276 18 1" x 20 UNEF 50,00 1.97 95,00 3.74 14.27 0.562 33,00 1.30 7,00 0.276 20 1 1/8" x 18 UNEF 45,50 1.80 90,50 3.57 15.88 0.625 37,50 1.48 7,00 0.276 22 1 1/4" x 18 UNEF 45,50 1.80 90,50 3.57 15.88 0.625 37,50 1.48 7,00 0.276 24 1 3/8" x 18 UNEF 47,50 1.87 77,50 3.05 19.05 0.750 43,30 1.71 7,00 0.276 28 1 5/8" x 18 UNEF 47,60 1.88 77,60 3.06 19.05 0.750 43,30 1.71 7,00 0.276 32 1 7/8" x 16 UN 46,50 1.83 76,50 3.02 23.80 0.937 51,70 2.04 7,00 0.276 36 2 1/16" x 16 UNS 46,40 1.826 76,40 3.01 31.75 1.250 58,00 2.29 7,00 0.276 40 2 5/16" x 16 UN 59,80 2.35 73,80 2.90 34.92 1.375 65,00 2.56 7,00 0.276 Shell Size 10SL 5 14S 3 16S 7 16 7 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR LOCKING SEALED CABLE CLAMP TYPE ‘HD’ STYLE: CIRBH - ** - ** - HD - F80 Oa ØF Thread C B ØT A How to order: CIRBH - ** - ** - HD - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B T Max Oa Min Overlap Accessory /8" x 24 UNEF 22,00 0.866 7,00 0.276 /4" x 20 UNEF 25,00 0.984 7,00 0.276 /8" x 20 UNEF 28,00 0.984 7,00 0.276 /8" x 20 UNEF 28,00 0.984 7,00 0.276 9,53 0.375 1" x 20 UNEF 31,00 1.220 7,00 0.276 19,00 0.748 12,70 0.500 1 1/8" x 18 UNEF 35,00 1.378 7,00 0.276 39,21 1.562 19,00 0.748 12,70 0.500 1 1/4" x 18 UNEF 38,00 1.496 7,00 0.276 65,61 2.583 44,45 1.750 23,80 0.937 15,09 0.594 1 3/8" x 18 UNEF 41,00 1.614 7,00 0.276 28 65,71 2.587 44,45 1.750 23,80 0.937 15,09 0.594 1 5/8" x 18 UNEF 48,00 1.890 7,00 0.276 32 70,96 2.794 57,15 2.250 31,75 1.250 23,83 0.938 1 7/8" x 16 UN 54,00 2.126 7,00 0.276 36 77,31 3.044 60,33 2.375 35,00 1.378 24,61 0.969 2 1/16" x 16 UNS 61,00 2.402 7,00 0.276 40 77,31 3.044 66,68 2.625 41,25 1.624 30,18 1.188 2 5/16" x 16 UN 67,00 2.638 7,00 0.276 C Shell Size A Max B Max Min 10SL 58,87 2.318 23,80 0.937 7,93 0.312 2,38 0.094 5 14S 58,87 2.318 26,97 1.062 11,12 0.438 6,35 0.250 3 16S 58,87 2.318 30,18 1.188 13,48 0.531 7,92 0.312 7 16 58,87 2.318 30,18 1.188 13,48 0.531 7,92 0.312 7 18 62,44 2.458 33,32 1.312 15,87 0.625 20 62,44 2.458 39,21 1.562 22 62,44 2.458 24 PAGE 68 NON-LOCKING CABLE CLAMP WITH BUSHING TYPE ‘JE’ STYLE: CIRBH - ** - ** - JE - F80 Oa ØF Thread S ØT L How to order: CIRBH - ** - ** - JE - F80 Shell size Metric Imperial Contact arrangement F Thread dia. Class 2B L Max S T Max Oa Min Overlap Accessory /8" x 24 UNEF 99,13 3.903 5.59 0.220 19,10 0.752 7,00 0.276 /4" x 20 UNEF 95,96 3.778 7.92 0.312 22,10 0.870 7,00 0.276 /8" x 20 UNEF 92,78 6.653 11.10 0.437 25,50 1.004 7,00 0.276 /8" x 20 UNEF 94,28 3.712 11.10 0.437 25,50 1.004 7,00 0.276 18 1" x 20 UNEF 97,51 3.839 14.27 0.562 28,60 1.126 7,34 0.289 20 1 1/8" x 18 UNEF 94,33 3.714 15.88 0.625 31,85 1.254 7,34 0.289 22 1 1/4" x 18 UNEF 94,33 3.714 15.88 0.625 35,03 1.379 7,34 0.289 24 1 3/8" x 18 UNEF 94,01 3.701 19.05 0.750 39,10 1.539 7,14 0.281 28 1 5/8" x 18 UNEF 94,01 3.701 19.05 0.750 45,60 1.795 6,34 0.250 32 1 7/8" x 16 UN 90,83 3.576 23.80 0.937 50,80 2.000 7,40 0.291 36 2 1/16" x 16 UNS 87,67 3.452 31.75 1.250 57,45 2.262 7,40 0.291 40 2 5/16" x 16 UN 84,43 3.324 34.92 1.375 63,10 2.484 6,34 0.250 Shell Size 10SL 5 14S 3 16S 7 16 7 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR LOCKING SCREENED CABLE ADAPTOR TYPE ‘M’ STYLE: CIRBH - ** - ** - SCA - F80 Oa ØF Thread ØS ØM N ØT How to order: CIRBH - ** - ** - SCA - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B M Max N Max S Min T Max Oa Min Overlap Accessory /8" x 24 UNEF 19,00 0.748 31,30 0.812 8,60 0.339 22,00 0.87 7,00 0.276 /4" x 20 UNEF 22,50 0.886 33,90 1.335 10,60 0.417 25,00 0.99 7,00 0.276 /8" x 20 UNEF 25,50 1.004 33,90 1.335 13,50 0.532 28,00 1.11 7,00 0.276 /8" x 20 UNEF 25,50 1.004 33,90 1.335 13,50 0.532 28,00 1.11 7,00 0.276 18 1" x 20 UNEF 25,50 1.004 36,90 1.453 14,60 0.575 31,00 1.22 7,00 0.276 20 1 1/8" x 18 UNEF 32,50 1.280 36,90 1.453 18,50 0.728 35,00 1.38 7,00 0.276 22 1 1/4" x 18 UNEF 34,50 1.358 36,90 1.453 20,80 0.819 38,00 1.50 7,00 0.276 24 1 3/8" x 18 UNEF 38,50 1.516 36,90 1.453 24,60 0.969 41,00 1.62 7,00 0.276 28 1 5/8" x 18 UNEF 41,50 1.634 35,90 1.413 27,00 1.063 48,00 1.89 7,00 0.276 32 1 7/8" x 16 UN 48,50 1.910 35,90 1.413 33,30 1.311 54,00 2.13 7,00 0.276 36 2 1/16" x 16 UNS 55,50 2.185 35,90 1.413 38,50 1.516 61,00 2.40 7,00 0.276 40 2 5/16" x 16 UN 62,50 2.461 35,90 1.413 45,00 1.772 67,00 2.638 7,00 0.276 Shell Size 10SL 5 14S 3 16S 7 16 7 PAGE 70 NON-LOCKING CONDUIT ADAPTOR TYPE ‘R’ STYLE: CIRBH - ** - ** - CCA - F80 Oa ØS ØF Thread ØF1 Thread ØT G N How to order: CIRBH - ** - ** - CCA - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B Shell Size 10SL 5 14S 3 16S 7 16 7 F1 Thread Dia. Class 2A G Max N Max S Min T Max Oa Min Overlap Accessory /8" x 24 UNEF 10,10 0.398 29,10 1.146 8,80 0.346 19,10 0.752 7,00 0.276 /4" x 20 UNEF 10,10 0.398 29,10 1.146 11,30 0.445 22,10 0.870 7,00 0.276 /8" x 20 UNEF 10,10 0.398 29,10 1.146 18,54 0.730 25,50 1.004 7,00 0.276 /8" x 20 UNEF 10,10 0.398 30,60 1.205 18,54 0.730 25,50 1.004 7,00 0.276 /8" x 24 UNEF 5 /4" x 20 UNEF 3 /8" x 20 UNEF 7 /8" x 20 UNEF 7 18 1" x 20 UNEF 1" x 20 UNEF 10,10 0.398 37,00 1.457 16,70 0.657 28,60 1.126 7,34 0.289 20 1 1/8" x 18 UNEF 1 3/16" x 18 UNEF 10,10 0.398 37,00 1.457 19,80 0.780 31,85 1.254 7,34 0.289 22 1 1/4" x 18 UNEF 1 3/16" x 18 UNEF 10,10 0.398 37,00 1.457 19,80 0.780 35,03 1.379 7,34 0.289 24 1 3/8" x 18 UNEF 1 7/16" x 18 UNEF 11,10 0.437 39,85 1.569 25,40 1.000 39,10 1.539 7,14 0.281 28 1 5/8" x 18 UNEF 1 7/16" x 18 UNEF 11,10 0.437 39,85 1.569 30,13 1.186 45,60 1.795 6,34 0.250 32 1 7/8" x 16 UN 1 3/4" x 18 UNS 11,10 0.437 39,85 1.569 32,50 1.280 50,80 2.000 7,40 0.291 36 2 1/16" x 16 UNS 2" x 18 UNS 11,10 0.437 39,85 1.569 35,70 1.406 57,45 2.262 7,40 0.291 40 2 5/16" x 16 UN 2 1/4" x 16 UN 11,10 0.437 39,85 1.569 45,00 1.772 63,10 2.484 6,34 0.250 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR NON-LOCKING SEALED CABLE CLAMP TYPE ‘RC’ STYLE: CIRBH - ** - ** - RC - F80 How to order: CIRBH - ** - ** - RC - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B T Max Oa Min Overlap Accessory /8" x 24 UNEF 19,10 0.752 7,00 0.276 /4" x 20 UNEF 22,10 0.870 7,00 0.276 /8" x 20 UNEF 25,50 1.004 7,00 0.276 /8" x 20 UNEF 25,50 1.004 7,00 0.276 9,53 0.375 1" x 20 UNEF 28,60 1.126 7,34 0.289 19,00 0.748 12,70 0.500 1 1/8" x 18 UNEF 31,85 1.254 7,34 0.289 39,21 1.562 19,00 0.748 12,70 0.500 1 1/4" x 18 UNEF 35,03 1.379 7,34 0.289 75,85 2.986 44,45 1.750 23,80 0.937 15,09 0.594 1 3/8" x 18 UNEF 39,10 1.539 7,14 0.281 28 75,85 2.986 44,45 1.750 23,80 0.937 15,09 0.594 1 5/8" x 18 UNEF 45,60 1.795 6.34 0.250 32 81,85 3.222 57,15 2.250 31,75 1.250 23,83 0.938 1 7/8" x 16 UN 50,80 2.000 7,40 0.291 36 88,85 3.498 60,33 2.375 35,00 1.378 24,61 0.969 2 1/16" x 16 UNS 57,45 2.262 7,40 0.291 40 88,85 3.498 66,68 2.625 41,25 1.624 30,18 1.188 2 5/16" x 16 UN 63,10 2.484 6.34 0.250 C Shell Size A Max B Max Min 10SL 59,10 2.327 23,80 0.937 7,93 0.312 2,38 0.094 5 14S 59,10 2.327 26,97 1.062 11,12 0.438 6,35 0.250 3 16S 59,10 2.327 30,18 1.188 13,48 0.531 7,92 0.312 7 16 60,60 2.386 30,18 1.188 13,48 0.531 7,92 0.312 7 18 70,00 2.756 33,32 1.312 15,87 0.625 20 70,00 2.756 39,21 1.562 22 70,00 2.756 24 PAGE 72 LONG BACKSHELL WITH CABLE CLAMP & BUSHING TYPE ‘XLA’ STYLE: CIRBH - ** - ** - XLA - F80 N ØT Ø T1 ØC Ø F Thread Oa How to order: CIRBH - ** - ** - XLA - F80 Shell size Metric Imperial Contact arrangement F Thread Dia. Class 2B N T Max T1 Max Oa Min Overlap Accessory /8" x 24 UNEF 118,35 4.659 22,00 0.866 22,70 0.894 7,00 0.276 /4" x 20 UNEF 115,18 4.535 25,00 0.984 27,50 1.083 7,00 0.276 /8" x 20 UNEF 112,00 4.409 28,00 1.102 30,00 1.181 7,00 0.276 /8" x 20 UNEF 122,30 4.815 28,00 1.102 30,00 1.181 7,00 0.276 14,27 0.562 1" x 20 UNEF 119,13 4.690 31,00 1.220 33,00 1.299 7,00 0.276 20 15,88 0.625 1 1/8" x 18 UNEF 115,95 4.565 35,00 1.378 37,50 1.476 7,00 0.276 22 15,88 0.625 1 1/4" x 18 UNEF 115,95 4.565 38,00 1.496 37,50 1.476 7,00 0.276 24 19,05 0.750 1 3/8" x 18 UNEF 112,78 4.440 41,00 1.614 43,30 1.704 7,00 0.276 28 19,05 0.750 1 5/8" x 18 UNEF 119,78 4.716 48,00 1.889 43,30 1.704 7,00 0.276 32 23,80 0.937 1 7/8" x 16 UN 116,60 4.591 54,00 2.126 51,70 2.035 7,00 0.276 36 31,75 1.250 2 1/16" x 16 UNS 113,43 4.466 61,00 2.402 58,00 2.283 7,00 0.276 40 34,92 1.375 2 5/16" x 16 UN 110,20 4.338 67,00 2.638 65,00 2.559 7,00 0.276 Shell Size C 10SL 5,59 0.220 5 14S 7,92 0.312 3 16S 11,10 0.437 7 16 11,10 0.437 7 18 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR LONG BACKSHELL WITH SEALED CABLE CLAMP TYPE ‘XLC’ STYLE: CIRBH - ** - ** - XLC - F80 N ØT Ø T1 ØC Ø F Thread Oa How to order: CIRBH - ** - ** - XLC - F80 Shell size Metric Imperial Shell Size Contact arrangement F Thread Dia. Class 2B N T Max T1 Max Oa Min Overlap Accessory /8" x 24 UNEF 79,47 3.129 22,00 0.866 23,80 0.937 7,00 0.276 /4" x 20 UNEF 79,47 3.129 25,00 0.984 26,97 1.062 7,00 0.276 /8" x 20 UNEF 79,47 3.129 28,00 1.102 30,18 1.188 7,00 0.276 /8" x 20 UNEF 91,33 3.596 28,00 1.102 30,18 1.188 7,00 0.276 C Max Min 10SL 7,93 0.312 2,38 0.094 5 14S 11,12 0.438 6,35 0.250 3 16S 13,48 0.531 7,92 0.312 7 16 13,48 0.531 7,92 0.312 7 18 15,87 0.625 9,53 0.375 1" x 20 UNEF 91,33 3.596 31,00 1.220 33,32 1.312 7,00 0.276 20 19,00 0.748 12,70 0.500 1 1/8" x 18 UNEF 91,33 3.596 35,00 1.378 39,67 1.562 7,00 0.276 22 19,00 0.748 12,70 0.500 1 1/4" x 18 UNEF 91,33 3.596 38,00 1.496 39,67 1.562 7,00 0.276 24 23,80 0.937 15,09 0.594 1 3/8" x 18 UNEF 94,51 3.721 41,00 1.614 44,45 1.750 7,00 0.276 28 23,80 0.937 15,09 0.594 1 5/8" x 18 UNEF 101,51 3.996 48,00 1.889 44,45 1.750 7,00 0.276 32 31,75 1.250 23,83 0.938 1 7/8" x 16 UN 107,86 4.246 54,00 2.126 57,15 2.250 7,00 0.276 36 35,00 1.378 24,61 0.969 2 1/16" x 16 UNS 114,21 4.496 61,00 2.402 60,33 2.375 7,00 0.276 40 41,25 1.624 30,18 1.188 2 5/16" x 16 UN 114,21 4.496 67,00 2.638 66,68 2.625 7,00 0.276 PAGE 74 LONG BACKSHELL WITH GROMMET TYPE ‘SHE’ STYLE: CIRBH - ** - ** - SHE - F80 B Oa ØD ØF Thread C ØE Thd. ØT How to order: CIRBH - ** - ** - SHE - F80 Shell size Metric Imperial Contact arrangement Shell Size ØT (Max.) B C ±0.10 ØD ±0/-0.10 Ø F Thd. 0a (Min) 10SL 22,0 0.866 48,5 1.909 15,0 0.591 8,5 0.335 5 /8" x 24 UNEF 7,0 0.276 14S 25,0 0.984 48,5 1.909 15,0 0.591 11,7 0.461 3 /4" x 20 UNEF 7,0 0.276 16S 28,0 1.102 48,5 1.909 15,0 0.591 13,9 0.547 7 /8" x 20 UNEF 7,0 0.276 16 28,0 1.103 58,8 2.303 15,0 0.591 13,9 0.547 7 /8" x 20 UNEF 7,0 0.276 18 31,0 1.220 58,8 2.303 15,0 0.591 16,9 0.666 1" x 20 UNEF 1" x 20 UNEF 7,0 0.276 20 35,0 1.378 58,8 2.303 15,0 0.591 20,9 0.823 1 3/16" x 18 UNEF 1 1/8" x 18 UNEF 7,0 0.276 22 38,0 1.496 58,8 2.303 15,0 0.591 20,9 0.823 1 3/16" x 18 UNEF 1 1/4" x 18 UNEF 7,0 0.276 24 41,0 1.614 58,8 2.303 15,0 0.591 25,9 1.020 1 7/16" x 18 UNEF 1 3/8" x 18 UNEF 7,0 0.276 28 48,0 1.890 65,8 2.303 15,0 0.591 25,9 1.020 1 7/16" x 18 UNEF 1 5/8" x 18 UNEF 7,0 0.276 32 54,0 2.126 65,8 2.303 15,0 0.591 32,0 1.260 1 3/4" x 18 UNS 1 7/8" x 16 UN 7,0 0.276 36 61,0 2.402 65,8 2.303 15,0 0.591 36,9 1.453 2" x 18 UNS 2 1/16" x 16 UNS 7,0 0.276 40 67,0 2.638 65,8 2.303 15,0 0.591 44,9 1.768 2 1/4" x 16 UN 2 5/16" x 16 UN 7,0 0.276 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR Ø E Thd. /8" x 24 UNEF 5 /4" x 20 UNEF 3 /8" x 20 UNEF 7 /8" x 20 UNEF 7 STEP-UP ADAPTOR TYPE ‘SUAM/SUAP’ STYLE: CIRBH - ** - ** - SUA* - F80 * Indicates: M = Metric / P = PG B ØA Ø E Thread Ø G Thread ØD Ø F Thread 12.00 15.00 ØA max. B ØD +0/-0.10 bore Thread E 1" x 20 UNEF 31.0 58.8 16.7 20 1 1/8" x 18 UNEF 35.0 58.8 22 1 1/4" x 18 UNEF 38.0 24 1 3/8" x 18 UNEF 28 Shell Size Thread F 10SL Consult TE 14S Consult TE 16S Consult TE 16 Consult TE 18 ØG Thread Metric PG 1 3/16" x 18 UNEF M25 x 1.5 PG 16 19.8 1 7/16" x 18 UNEF M32 x 1.5 PG 21 58.8 19.8 1 7/16" x 18 UNEF M32 x 1.5 PG 21 41.0 58.8 25.4 1 3/4" x 18 UNEF M40 x 1.5 PG 29 1 5/8" x 18 UNEF 48.0 65.8 27.0 1 3/4" x 18 UN M40 x 1.5 PG 29 32 1 7/8" x 16 UNEF 54.0 65.8 32.5 2" x 18 UNS M40 x 1.5 PG 29 36 2 1/16" x 16 UNS 61.0 65.8 35.7 2 1/4" x 16 UN M50 x 1.5 PG 36 40 2 5/16" x 16 UNS 67.0 65.8 45.0 2 1/2" x 16 UN M50 x 1.5 PG 42 PAGE 76 STEP-DOWN ADAPTORS METRIC/PG INNER THREAD, IMPERIAL OUTER THREAD STYLE: CIRBH - ** - ** - SDA* * Indicates: M = Metric / P = PG B ØA Ø E Thread Ø G Thread ØD Ø F Thread 12.00 15.00 Shell Size ØF Thread 10SL Consult TE 14S Consult TE 16S Consult TE 16 Consult TE 18 1" x 20 UNEF 20 ØG Thread ØA max. B ØD +0/-0.10 Bore PG11 31.00 58.8 TBC M20 x 1.5 PG13.5 35.00 58.8 TBC 1" x UNEF M20 x 1.5 PG13.5 38.00 58.8 TBC 1 3/8" x 18 UNEF 1 3/16" x 18 UNEF M25 x 1.5 PG16 41.00 58.8 TBC 28 1 5/8" x 18 UNEF 1 3/16" x 18 UNEF M25 x 1.5 PG16 48.00 65.8 TBC 32 1 7/8" x 16 UNEF 1 7/16" x 16 UNEF M32 x 1.5 PG21 54.00 65.8 TBC 36 2 1/16" x 16 UNS 1 3/4" x 16 UNEF M40 x 1.5 PG29 61.00 65.8 TBC 40 2 5/16" x 16 UNS 2" x 16 UNS M40 x 1.5 PG29 67.00 73 TBC ØE Thread Metric PG /8" x 20 UNEF M18 x 1.5 1 1/8" x 18 UNEF 1" x UNEF 22 1 1/4" x 18 UNEF 24 7 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR SCREENED SHELL EXTENDER METRIC/PG INNER THREAD, IMPERIAL OUTER THREAD STYLE: CIRBH - ** - ** - SUA*S * Indicates: M = Metric / P = PG Shell Size ØF Thread 10SL Consult TE 14S Consult TE 16S Consult TE 16 Consult TE 18 1" x 20 UNEF 20 ØE Thread ØG Thread ØA max. B PG16 31.00 83.3 M32 x 1.5 PG21 35.00 83.3 1 7/16" x 18 UNEF M32 x 1.5 PG21 38.00 83.3 1 3/8" x 18 UNEF 1 3/4" x 18 UNEF M40 x 1.5 PG29 41.00 83.3 28 1 5/8" x 18 UNEF 1 3/4" x 18 UN M40 x 1.5 PG29 48.00 83.3 32 1 7/8" x 16 UNEF 2" x 18 UNS M40 x 1.5 PG29 54.00 83.3 36 2 1/16" x 16 UNS 2 1/4" x 16 UN M50 x 1.5 PG36 61.00 83.3 40 2 5/16" x 16 UNS 2 1/2" x 16 UN M50 x 1.5 PG42 67.00 83.3 Metric PG 1 3/16" x 18 UNEF M25 x 1.5 1 1/8" x 18 UNEF 1 7/16" x 18 UNEF 22 1 1/4" x 18 UNEF 24 PAGE 78 PG THREADED ADAPTORS (FITTING ON ACA, CCA, XL & FT ACCESSORY WITH PG/METRIC THREAD) Part Number Key CIRB ## #GA # THREAD D THREAD C ‘O’RING SEAL Thread ‘D’ (see table) P/N Prefix Accessory Size Thread Designation P GA - Imperial M GA - Metric P/N Example to fit shell size 20 with a rear metric thread size M25 CIRB 20 M GA D ØA B Shell Size Part Number ØA B Thread C 10SL CIRB-10SL-#GA-#M32 20.00 35.00 5 14S CIRB-14S-#GA-#M32 23.50 35.00 3 16S CIRB-16S-#GA-#M32 28.00 35.00 7 18 CIRB-18-#GA-#M32 34.00 40.00 20-22 CIRB-20-#GA-#M32 37.00 35.00 20-22 CIRB-20-#GA-#M32 24-28 CIRB-24-#GA-#M32 24-28 CIRB-24-#GA-#M32 24-28 CIRB-24-#GA-#M32 /8" x 24 UNEF /4" x 20 UNEF /8" x 20 UNEF 1" x 20 UNEF 1 3/16" x 18 UNEF 43.00 40.00 1 7/16" x 18 UNEF 46.00 54.00 32 CIRB-32-#GA-#M32 36 CIRB-36-#GA-#M32 40 CIRB-40-#GA-#M32 Thread Table (D) Imperial (PGA) Thread Size Metric (MGA) Thread Size A PG7 A M12 B PG9 B M16 C PG11 C M20 D PG13.5 D M25 E PG16 E M32 F PG21 F M40 G PG29 G M50 H PG36 H M63 J PG42 K PG48 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR 38.00 1 3/4" x 18 UNS 57.20 50.00 2" x 18 UNS 65.00 51.00 2 1/4" x 16 UN CABLE CLAMP STYLE: MS3057A A Thread B C D Metric Imperial A Thread Dia. Class 2A B Max C Max D Max /8" x 24 UNEF 21,41 0.843 7,95 0.313 21,41 0.843 /4" x 20 UNEF 25,40 1.000 11,13 0.438 23,01 0.906 /8" x 20 UNEF 28,58 1.125 14,30 0.563 24,61 0.969 /8" x 20 UNEF 28,58 1.125 14,30 0.563 24,61 0.969 CIRMSP3057A18 1" x 20 UNEF 30,96 1.219 15,88 0.625 24,61 0.969 -12A CIRMSP3057A20 1 3/16" x 18 UNEF 35,71 1.406 19,05 0.750 24,61 0.969 22 -12A CIRMSP3057A22 1 3/16" x 18 UNEF 35,71 1.406 19,05 0.750 24,61 0.969 24 -16A CIRMSP3057A24 1 7/16" x 18 UNEF 42,85 1.687 23,83 0.938 26,97 1.062 28 -16A CIRMSP3057A28 1 7/16" x 18 UNEF 42,85 1.687 23,83 0.938 26,97 1.062 32 -20A CIRMSP3057A32 1 3/4" x 18 UNS 52,37 2.062 31,75 1.250 28,58 1.125 36 -24A CIRMSP3057A36 2" x 18 UNS 57,15 2.250 34,93 1.375 30,15 1.187 40 -28A CIRMSP3057A40 2 1/4" x 16 UN 64,29 2.531 41,28 1.625 43,66 1.719 Shell Size MS3057 Reference Part Number 10SL -4A CIRMSP3057A10SL 5 14S -6A CIRMSP3057A14S 3 16S -8A CIRMSP3057A16S 7 16 -8A CIRMSP3057A16 7 18 -10A 20 PAGE 80 SEALED CABLE CLAMP FOR JACKETED CABLE STYLE: MS3057C D A Thread C Dia E Metric Imperial A Thread Dia. Class 2A Max Min D Max E Max /8" x 24 UNEF 7,93 0.312 2,38 0.094 34,93 1.375 23,80 0.937 /4" x 20 UNEF 11,12 0.438 6,35 0.250 34,93 1.375 26,97 1.062 /8" x 20 UNEF 13,48 0.531 7,92 0.312 34,93 1.375 30,18 1.188 /8" x 20 UNEF 13,48 0.531 7,92 0.312 34,93 1.375 30,18 1.188 CIRMSP3057C18 1" x 20 UNEF 15,87 0.625 9,53 0.375 36,50 1.437 33,32 1.312 -12C CIRMSP3057C20 1 3/16" x 18 UNEF 19,00 0.748 12,70 0.500 36,50 1.437 39,21 1.562 22 -12C CIRMSP3057C22 1 3/16" x 18 UNEF 19,00 0.748 12,70 0.500 36,50 1.437 39,21 1.562 24 -16C CIRMSP3057C24 1 7/16" x 18 UNEF 23,80 0.937 15,09 0.594 39,67 1.562 44,45 1.750 28 -16C CIRMSP3057C28 1 7/16" x 18 UNEF 23,80 0.937 15,09 0.594 39,67 1.562 44,45 1.750 32 -20C CIRMSP3057C32 1 3/4" x 18 UNS 31,75 1.250 23,83 0.938 46,02 1.812 57,15 2.250 36 -24C CIRMSP3057C36 2" x 18 UNS 35,00 1.378 24,61 0.969 52,37 2.062 60,33 2.375 40 -28C CIRMSP3057C40 2 1/4" x 16 UN 41,25 1.624 30,18 1.188 52,37 2.062 66,68 2.625 Shell Size MS3057 Reference Part Number 10SL -4C CIRMSP3057C10SL 5 14S -6C CIRMSP3057C14S 3 16S -8C CIRMSP3057C16S 7 16 -8C CIRMSP3057C16 7 18 -10C 20 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR C Dia. TELESCOPIC BUSHING STYLE: MS 3057A D B C A Metric Imperial Note: The bushings can fit inside one another to reduce the cable entry diameter and improving clamping and sealing. Shell Size Part Number A B C D 10SL CIRSBMSH5541 12,83 0.505 69,85 2.750 5,59 0.220 7,62 0.300 14S CIRSBMSH5542 15,88 0.625 66,68 2.625 7,92 0.312 10,80 0.425 16S CIRSBMSH5543 19,05 0.750 63,50 2.500 11,10 0.437 13,97 0.550 16 CIRSBMSH5543 19,05 0.750 63,50 2.500 11,10 0.437 13,97 0.550 18 CIRSBMSH5544 22,23 0.875 60,33 2.375 14,27 0.562 15,57 0.613 20 CIRSBMSH5545 25,40 1.000 57,15 2.250 15,88 0.625 18,75 0.738 22 CIRSBMSH5546 28,58 1.125 57,15 2.250 15,88 0.625 18,75 0.738 24 CIRSBMSH5547 31,75 1.250 53,98 2.125 19,05 0.750 23,50 0.925 28 CIRSBMSH5548 38,23 1.505 53,98 2.125 19,05 0.750 23,50 0.925 32 CIRSBMSH5549 44,45 1.750 50,80 2.000 23,80 0.937 31,45 1.238 36 CIRSBMSH55410 47,88 1.885 47,63 1.875 31,75 1.250 34,62 1.363 40 CIRSBMSH55411 52,90 2.083 44,40 1.748 34,92 1.375 40,99 1.614 PAGE 82 PANEL SEALING GASKETS NON-SCREENING, SEALING ONLY RFI CONDUCTIVE SCREENING & SEALING ØB 4 Holes Ød T 4 Holes Ød T ØB1 A SQ. Front Mounted Receptacle Part Number: Non-Screening- CIRSB - ** - RPG RFI Screening- CIRSB - ** - RPGS A SQ. Rear Mounted Receptacle Part Number: Non-Screening- CIRSB - ** - FPG RFI Screening- CIRSB - ** - FPGS Metric Imperial Shell Size A Min B Nominal B1 Nominal d Min T Nominal 10SL 25,40 1.000 15,88 0.625 18,30 0.720 3,43 0.135 1,00 0.040 14S 30,20 1.188 19,00 0.750 24,70 0.972 3,43 0.135 1,00 0.040 16S 32,50 1.280 22,20 0.875 27,50 1.083 3,43 0.135 1,00 0.040 16 32,50 1.280 22,20 0.875 27,50 1.083 3,43 0.135 1,00 0.040 18 34,90 1.375 25,40 1.000 30,90 1.217 3,43 0.135 1,00 0.040 20 38,10 1.500 28,60 1.125 34,30 1.350 3,43 0.135 1,00 0.040 22 41,30 1.625 31,70 1.250 37,50 1.476 3,43 0.135 1,00 0.040 24 44,50 1.750 34,90 1.375 41,00 1.614 4,12 0.162 1,00 0.040 28 50,80 2.000 41,30 1.625 46,80 1.843 4,12 0.162 1,00 0.040 32 57,20 2.250 47,60 1.875 53,50 2.106 4,78 0.188 1,00 0.040 36 63,50 2.500 52,60 2.071 59,70 2.350 4,78 0.188 1,00 0.040 40 69,90 2.750 61,90 2.440 65,50 2.580 5,10 2.010 1,00 0.040 *49 110,00 4.331 98,10 3.862 98,10 3.862 7,90 0.311 1,25 0.049 *Size 49 is available as non-screened version only. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR PROTECTIVE CAPS STYLES: CIRBE - ** - X-PCA/X-PCAK & X-PCAJ/X-PCAJK TEB - ** - E-PAC/E-PCAK CIRBE-**-X-PCA (with nylon cord) CIRBE-**-X-PCAK (with sash chain) - **-X-PCJaK ABBE - **-X-PCAJ - **-X-PCAK ABBE - **-X-PCA ABBE - **-X-PCJaK ABBE - F1 **-X-PCAJ ABBE - ** ABBE -ABBE **-X-PCAJ F1 ABBE - **-X-PCAK ABBE - F1 **-X-PCA ABBEF1 - **-X-PCAK ABBE -ABBE **-X-PCA F1 E1 (withcord) sash chain)(with sash chain) (with nylon E1 cord)(with nylon (withcord) sash chain)(with sash chain) E1 cord) (with nylon E1 cord)(with nylon (with sash (with nylon E1 cord) (with sash chain) (with nylon 0m 0m 0m 0m 0m F1 E1 0m Ød1 ØB ØB Ød1 Ød2 Ød1 Ød2 L F2 E2 0m L ØB Ød1 L F1 E1 0m ABBE - **-X-PCAK (with sash chain) L Ød1 Ød2 Ød2 Ød2 CIRB-**-E-PCA Ød1 (with nylon cord) Ød1 L L L ØC Ød1 ØD L L L F1 E1 0m Ød2 L ABBEF1 - **-X-PC ABB (withE1 nylon cord) (wit 0m L ØB ØB (with sash chain) L L L ABB - **-E-PCAK ABB - **-E-PCAK (with sash chain) (with sash chain) Ød2 Ød1 Cap Mou Ød2 ØB L L L L L L ABB - **-E-PCAK BB - **-E-PCA ith nylonCaps cord) (with sash chain) for Single Hole Ød2 Mounting Receptacle Ød1 Caps for Single Hole Mounting Receptacle Metric Imperial L L L L L Shell Size B Max C Max D Max E1 Max E2 Max F1 Max F2 Max L approx. See note d1 Min d2 +0.5, -0 +0.02, -0 Om Min Overlap Mated 10SL 22,80 0.898 26,10 1.028 18,20 0.717 17,50 0.689 21,60 0.850 24,60 0.969 28,40 1.118 100,00 4.000 4,85 0.191 4,30 0.169 11,10 0.437 14S 29,20 1.150 32,50 1.280 24,60 0.969 17,50 0.689 21,60 0.850 24,60 0.969 28,40 1.118 100,00 4.000 4,85 0.191 4,30 0.169 11,10 0.437 16S 32,40 1.276 35,30 1.390 27,40 1.079 17,50 0.689 21,60 0.850 24,60 0.969 28,40 1.118 100,00 4.000 4,85 0.191 4,30 0.169 11,10 0.437 16 32,40 1.276 35,30 1.390 27,40 1.079 24,00 0.945 27,30 1.075 24,60 0.969 28,40 1.118 100,00 4.000 4,85 0.191 4,30 0.169 15,85 0.624 18 36,50 1.437 38,70 1.524 30,80 1.213 24,00 0.945 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 4,30 0.169 15,85 0.624 20 39,90 1.571 42,10 1.658 34,20 1.346 24,00 0.945 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 4,30 0.169 15,85 0.624 22 43,10 1.697 45,30 1.784 37,40 1.472 24,00 0.945 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 4,30 0.169 15,75 0.620 24 46,60 1.835 48,80 1.921 40.90 1.610 24,00 0.945 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 4,30 0.169 15,75 0.620 28 53,40 2.102 54,60 2.150 46,70 1.838 24,00 0.945 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 4,30 0.169 15,75 0.620 32 60,10 2.366 61,30 2.413 53,40 2.102 27,00 1.063 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 5,50 0.217 15,75 0.620 36 66,30 2.610 67,50 2.658 59,60 2.346 27,00 1.063 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 5,50 0.217 15,75 0.620 40 72,10 2.838 73,40 2.890 65.50 2.579 27,00 1.063 27,30 1.075 29,80 1.173 33,90 1.335 150,00 6.000 4,85 0.191 5,50 0.217 15,75 0.620 L L Caps for Single CapsHole for Single Caps Hole for Single Hole CIRB-**-E-PCAK Mounting Receptacle Mounting Receptacle Mounting Receptacle L Ød1 Ød2 L F2 E2 ABB ABB- -**-X-PCJaK **-E-PCA 0m - **-E-PCA ABBE (with nylon(with cord) (with nylon cord) sash chain) (with nylon cord) L ØD Ød2 L F2 E2 0m ABBE - **-X-PCAJ ØC ABBE - **-X-PCAK ABBE - **-X-PCAK (with sash chain) (with sash chain) ABBEF1 - **-X-PCA ABBE - **-X-PCA (withE1 nylon cord) (with nylon cord) 0m L ØB ØB ØB F2 F2 E2 E2 ABB - **-E-PCAK ABB0m - **-E-PCAABB ABB - **-E-PCAK ABB - **-E-PCAK ABB - **-E-PCA 0m- **-E-PCA (withcord) sash chain)(with sash chain) (with nylon cord)(with nylon cord) (with sash chain) (with nylon ABBE - **-X-PCJaK (with sash chain) BBE - **-X-PCA ith nylon cord) L L CIRBE-**-X-PCAJK Ød1 ØC ØC ØD ØD ØD (with sash chain) BE - **-X-PCAJ h nylon cord) Ød2 ØB ØB F1 E1 0m ØC CIRBE-**-X-PCAJ (with nylon cord) Note: For alternative cord or chain length, please consult TE. PAGE 84 INDIVIDUAL WIRE SEAL GROMMET DUMMY PIN, SOCKET & GROMMET FILLER PLUG How to order: CIRBH - ** - ** - GAC - F80 Shell size Contact arrangement Metric Imperial F80 Contact Sizes AWG (Metric) *Wire Insulation Min O/D *Wire Insulation Max O/D 16S/16 (15S/15) 1,52 0.060 3,20 0.126 12 (25) 2,44 0.096 5,12 0.202 8 (100) 4,90 0.193 7,20 0.283 4 (160) 8.18 0.322 11,00 0.433 **0 (500) 14,00 0.551 16,00 0.630 * ** Please contact sales office for further detail. For details of grommet reducing bushes to suit 35mm2, 25mm2 & 16mm2 wire, please contact the sales office. Grommet Filler Plug Ød L Dummy Contact Ød1 L1 Ød Ød1 L1 L CIRB-**-KFP F80 CIRB-**-KDP F80 Metric Imperial * *** Contact Size AWG (Metric) L Max d Max L1 Max d1 Max Colour Code ***16 (15) 12,30 0.484 3,90 0.154 20,00 0.787 3,20 0.126 Brown (KDP/KDS) 12 (25) 12,30 0.484 4,80 0.189 20,40 0.803 4,80 0.189 Orange 8 (100) 12,10 0.476 7,00 0.276 22,75 0.896 7,80 0.307 Violet 4 (160) 12,10 0.476 10,20 0.402 * * Black 0 (500) 12,50 0.500 15,60 0.614 24,60 0.969 15,00 0.590 White Please consult TE for availability. For Grommet Filler Plugs (KFP), do not add F80 to part number. Colour Blue. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR SQUARE FLANGE STOWAGE RECEPTACLE STYLE: CIR - ** - SX/SX - M6 4 Holes Ø d1 C X 4 Tapped Holes d2 (M6 MOD.) Om X B C Metric Imperial E Note: See page 90 for mounting details • This part has a hole through the centre • In order to maintain sealing to a panel (when used with Gasket), the panel cut out should not include the connector through hole • Not normally practical with tapped holes. Part Number B Max C Max D1 Min d2 Thread E Max X Om min overlap mated CIR-10SL-SX 17,60 0.693 25,70 1.012 3,20 0.126 M4 3,00 0.118 18,20 0.717 11,10 0.437 CIR-14S-SX 18,00 0.709 30,30 1.193 3,20 0.126 M4 3,40 0.134 23,10 0.909 11,10 0.437 CIR-16S-SX 18,00 0.709 32,80 1.291 3,20 0.126 M4 3,40 0.134 24,60 0.969 11,10 0.437 CIR-16-SX 22,80 0.898 32,80 1.291 3,20 0.126 M4 3,40 0.134 24,60 0.969 15,85 0.624 CIR-18-SX 23,60 0.929 35,30 1.390 3,20 0.126 M4 4,20 0.165 27,00 1.063 15,85 0.624 CIR-20-SX 23,60 0.929 38,30 1.508 3,20 0.126 M4 4,20 0.165 29,40 1.157 15,85 0.624 CIR-22-SX 23,60 0.929 41,30 1.626 3,20 0.126 M4 4,20 0.165 31,80 1.252 15,75 0.620 CIR-24-SX 25,20 0.992 44,80 1.764 3.70 0.146 M4 4,20 0.165 34,90 1.374 15,75 0.620 CIR-28-SX 25,20 0.992 51,10 2.012 3,70 0.146 M5 4,20 0.165 39,70 1.563 15,75 0.620 CIR-32-SX 26,80 1.055 57,30 2.256 4,30 0.169 M5 4,20 0.165 44,50 1.752 15,75 0.620 CIR-36-SX 26,80 1.055 63,80 2.512 4,30 0.169 M5 4,20 0.165 49,20 1.937 15,75 0.620 CIR-40-SX 26,80 1.055 70,20 2.763 4,30 0.169 M5 4,20 0.165 55,50 2.185 15,75 0.620 CIR-49-SX 56,73 2.233 110,40 4.346 8,50 0.335 - 8,20 0.323 90,00 3.543 PAGE 86 SQUARE FLANGE RECEPTACLE NUT PLATES STYLE: CIRB ** NP (METRIC THREAD)/NPA (UNC THREAD) B D F Dia. B A E C Dia. A T Thread Typical On 4 Metric Imperial Shell Size A B Max C Dia. Max D E Max F Dia. Max T Thread Part Number T Thread Part Number 10SL 18,26 0.719 26,26 1.034 17,85 0.702 2,69/4,22 0.106/0.166 11,50 0.453 6,00 0.236 M3 x 0,5 CIRB10SLNP 4 - 40 UNC CIRB10SLNPA 14S 23,01 0.906 30,66 1.207 24,59 0.968 2,69/4,22 0.106/0.166 16,25 0.640 6,00 0.236 M3 x 0,5 CIRB14SNP 4 - 40 UNC CIRB14SNPA 16S 24,61 0.969 32,26 1.270 28,17 1.109 2,69/4,22 0.106/0.166 17,85 0.703 6,00 0.236 M3 x 0,5 CIRB16SNP 4 - 40 UNC CIRB16SNPA 16 24,61 0.969 32,26 1.270 28,17 1.109 2,69/4,22 0.106/0.166 17,85 0.703 6,00 0.236 M3 x 0,5 CIRB16NP 4 - 40 UNC CIRB16NPA 18 26,97 1.062 34,62 1.363 30,48 1.250 2,69/4,22 0.106/0.166 20,21 0.796 6,00 0.236 M3 x 0,5 CIRB18NP 4 - 40 UNC CIRB18NPA 20 29,36 1.156 38,48 1.515 33,53 1.320 2,69/4,22 0.106/0.166 22,47 0.885 6,00 0.236 M3 x 0,5 CIRB20NP 4 - 40 UNC CIRB20NPA 22 31,75 1.250 40,84 1.608 36,65 1.443 2,69/4,22 0.106/0.166 23,54 0.927 6,00 0.236 M3 x 0,5 CIRB22NP 4 - 40 UNC CIRB22NPA 24 34,93 1.375 44,83 1.765 40,00 1.575 2,69/4,22 0.106/0.166 25,90 1.020 7,50 0.295 M3 x 0,5 CIRB24NP 4 - 40 UNC CIRB24NPA 28 39,67 1.562 51,18 2.015 46,61 1.835 2,69/4,22 0.106/0.166 29,08 1.145 7,50 0.295 M3 x 0,5 CIRB28NP 4 - 40 UNC CIRB28NPA 32 44,45 1.750 59,10 2.327 52,75 2.077 3,50/5,00 0.138/0.197 30,68 1.208 8,00 0.315 M4 x 0,7 CIRB32NP 8 - 32 UNC CIRB32NPA 36 49,23 1.968 63,86 2.514 59,10 2.327 3,50/5,00 0.138/0.197 35,43 1.395 8,00 0.315 M4 x 0,7 CIRB36NP 8 - 32 UNC CIRB36NPA 40 55,58 2.188 74,68 2.940 68,33 2.690 3,50/5,00 0.138/0.197 38,60 1.520 8,00 0.315 M4 x 0,7 CIRB40NP 8 - 32 UNC CIRB40NPA RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR SQUARE FLANGE RECEPTACLES PANEL MOUNTING DETAIL VV VV ØW ØW XX ØW1 ØW1 XX XX 44Holes Holesd3 d3 (See (Seenote) note) 44Holes Holesd3 d3 (See (Seenote) note) Front Mounting Style: Rear Mounting Style: CIRH00 CIRH04 CIRH12A CIRH03 CIRH05 & 07 Note 1: When fixed connectors are used with threaded mounting holes, refer to hole sizes in column d4. Metric Imperial XX Note 2:. When fixed connectors are used with plugs having rubber coupling nuts, please consult factory for panel cut-out dimensions. Shell Size d3 dia. d4 dia. V W W1 X 10SL 3,40 0.134 4,50 0.177 26,60 1.047 17,00 0.670 18,58 0.732 18,20 0.717 14S 3,40 0.134 4,50 0.177 31,60 1.244 20,00 0.780 24,98 0.984 23,00 0.906 16S 3,40 0.134 4,50 0.177 34,40 1.354 23,00 0.906 27,78 1.094 24,60 0.969 16 3,40 0.134 4,50 0.177 34,40 1.354 23,00 0.906 27,78 1.094 24,60 0.969 18 3,40 0.134 4,50 0.177 38,30 1.508 26,00 1.024 31,18 1.228 27,00 1.063 20 3,40 0.134 4,50 0.177 41,70 1.642 30,00 1.181 34,58 1.361 29,40 1.157 22 3,40 0.134 4,50 0.177 45,20 1.780 33,00 1.300 37,78 1.487 31,80 1.252 24 3,90 0.154 4,50 0.177 48,70 1.917 36,00 1.417 41,28 1.625 34,90 1.374 28 3,90 0.154 5,50 0.217 55,50 2.185 42,00 1.654 47,08 1.854 39,70 1.563 32 4,50 0.177 5,50 0.217 62,40 2.475 48,50 1.909 53,78 2.117 44,50 1.752 36 4,50 0.177 5,50 0.217 69,00 2.717 55,00 2.165 59,98 2.361 49,20 1.937 40 4,50 0.177 5,50 0.217 75,00 2.953 59,10 2.327 66,4 2.614 55,50 2.186 49 8,50 0.315 - 140,00 5.512 91,00 3.583 91,00 3.583 90,00 3.543 PAGE 88 SINGLE HOLE MOUNTING RECEPTACLE PANEL MOUNTING DETAIL K H ctrs. J dia. Note: When fixed connectors are used with plugs having rubber coupling nuts, please consult factory for panel cut-out dimensions. Metric Imperial Shell Size H ctrs. J dia. K 10SL 32,55 1.281 22,53 0.887 20,83 0.820 14S 42,05 1.656 28,88 1.137 27,23 1.072 16S 45,15 1.776 32,08 1.263 30,78 1.212 16 45,15 1.776 32,08 1.263 30,78 1.212 18 48,85 1.923 35,23 1.387 33,58 1.322 20 52,05 2.049 38,43 1.513 36,68 1.444 22 55,45 2.183 41,56 1.636 39,88 1.570 24 58,45 2.301 44,78 1.763 43,18 1.700 28 65,25 2.569 51,13 2.013 49,37 1.944 32 71,55 2.817 57,48 2.263 55,78 2.196 36 77.95 3.069 63,83 2.513 62,18 2.448 40 85,25 3.356 70,18 2.763 68,38 2.692 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR CONTACT INSERTION & EXTRACTION TOOLS SOCKET CONTACT GUIDE PINS Socket Insertion Tool Pin Extraction Tool Contact Size AWG (Metric) Insertion Tool Part Number Contact Size AWG (Metric) Extraction Tool Part Number 16 (16S) CIRB-IT-16 16 (16S) CIRB-ET-16 16 (15) CIRB-IT-16 16 (15) CIRB-ET-16 12 (25) CIRB-IT-12 12 (25) CIRB-ET-12 8 (100) 4 (160) 8 (100) Tool Not Required 0 (500) 4 (160) Tool Not Required 0 (500) Socket Contact Guide Pin Socket Contact Size AWG (Metric) Guide Pin Part Number 16 (16S) CIRB-16-SGP 16 (15) CIRB-16-SGP 12 (25) CIRB-12-SGP 8 (100) 4 (160) Guide Pin Not Required 0 (500) PAGE 90 F80 CONTACTS CRIMP & TOOLING DATA Contact Size & Type Contact Part Number Wire Size C.S.A. mm2 Tool Required Turret/ Locator Tool Setting Tool Pos’n If Applicable Insertion Tool Extraction Tool Guide Pins 16S/20 Pin CIRB16S/20KPKF80 0,5/0,6 FT8/WA27F TP1249 3 - CIRIT16 CIRET16 - 16S/20 Skt. CIRB16S/20KSKF80 0,5/0,6 FT8/WA27F TP1249 3 - CIRIT16 CIRET16 CIRB16SG 16S/18 Pin CIRB16S/18KPKF80 0,75/0,93 FT8/WA27F TP1249 4 - CIRIT16 CIRET16 - 16S/18 Skt. CIRB16S/18KSKF80 0,75/0,93 FT8/WA27F TP1249 4 - CIRIT16 CIRET16 CIRB16SG 16S/14 Pin CIRB16S/14KPKf80 1,94/2,08 FT8/WA27F TP1249 5 - CIRIT16 CIRET16 - 16S/14 Skt. CIRB16S/14KSKf80 1,94/2,08 FT8/WA27F TP1249 5 - CIRIT16 CIRET16 CIRB16SG 16S/12 Pin CIRB16S/12KPKf80 2,50/3,00 FT8/WA27F TP1249 7 - CIRIT16 CIRET16 - 16S/12 Skt. CIRB16S/12KPKf80 2,50/3,00 FT8/WA27F TP1249 7 - CIRIT16 CIRET16 CIRB16SG 16S Pin CIRB16SKPKF80 0,93/1,5 FT8/WA27F TP1249 5 - CIRIT16 CIRET16 - 16S Skt. CIRB16SKSKF80 0,93/1,5 FT8/WA27F TP1249 5 - CIRIT16 CIRET16 CIRB16SG LIF 16S Skt. CIRB16SKLKF80 0,93/1,5 FT8/WA27F TP1249 5 - CIRIT16 CIRET16 CIRB16SG 16/22 Pin CIRB16/22KPKF80 0,22/0,34 FT8/WA27F TH592 2/3 Red CIRIT16 CIRET16 - 16/22 Skt. CIRB16/22KSKF80 0,22/0,34 FT8/WA27F TH592 2/3 Blue CIRIT16 CIRET16 CIRB16SG 16/20 Pin CIRB16/20KPKF80 0,5/0,6 FT8/WA27F TH592 3 Blue CIRIT16 CIRET16 - 16/20 Skt. CIRB16/20KSKF80 0,5/0,6 FT8/WA27F TH592 3 Red CIRIT16 CIRET16 CIRB16SG LIF16/20 Skt. CIRB16/20KLKF80 0,5/0,6 FT8/WA27F TH592 3 Red CIRIT16 CIRET16 CIRB16SG 16/18 Pin CIRB16/18KPKF80 0,75/0,93 FT8/WA27F TH592 4 Blue CIRIT16 CIRET16 - 16/18 Skt. CIRB16/18KSKF80 0,75/0,93 FT8/WA27F TH592 4 Red CIRIT16 CIRET16 CIRB16SG 16 Pin CIRB16KPKF80 0,93/1,5 FT8/WA27F TH592 5 Blue CIRIT16 CIRET16 - 16 Skt. CIRB16KSKF80 0,93/1,5 FT8/WA27F TH592 5 Red CIRIT16 CIRET16 CIRB16SG LIF 16 Skt. CIRB16KLKF80 0,93/1,5 FT8/WA27F TH592 5 Red CIRIT16 CIRET16 CIRB16SG 16/14 Pin CIRB16/14KPKF80 1,94/2,08 FT8/WA27F TH592 5 Blue CIRIT16 CIRET16 - 16/14 Skt. CIRB16/14KSKF80 1,94/2,08 FT8/WA27F TH592 5 Red CIRIT16 CIRET16 CIRB16SG 16/12 Pin CIRB16/12KPKF80 2,50/3,00 FT8/WA27F TH592 7 Yellow CIRIT16 CIRET16 - 16/12Skt. CIRB16/12KSKF80 2,50/3,00 FT8/WA27F TH592 7 Yellow CIRIT16 CIRET16 CIRB16SG 12/20 Pin CIRB12/20KPKF80 0,5/0,6 FT8/WA27F TH592 3 Yellow CIRIT12 CIRET12 - 12/20 Skt. CIRB12/20KSKF80 0,5/0,6 FT8/WA27F TH592 3 Yellow CIRIT12 CIRET12 CIRB12SG LIF 12/20 Skt. CIRB12/20KLKF80 0,5/0,6 FT8/WA27F TH592 3 Yellow CIRIT12 CIRET12 CIRB12SG 12/18 Pin CIRB12/18KPKF80 0,75/0,93 FT8/WA27F TH592 4 Yellow CIRIT12 CIRET12 - 12/18 Skt. CIRB12/18KSKF80 0,75/0,93 FT8/WA27F TH592 4 Yellow CIRIT12 CIRET12 CIRB12SG 12/16 Pin CIRB12/16KPKF80 0,93/1,5 FT8/WA27F TH592 5 Yellow CIRIT12 CIRET12 - 12/16 Skt. CIRB12/16KSKF80 0,93/1,5 FT8/WA27F TH592 5 Yellow CIRIT12 CIRET12 CIRB12SG LIF 12/16 Skt. CIRB12/16KLKF80 0,93/1,5 FT8/WA27F TH592 5 Yellow CIRIT12 CIRET12 CIRB12SG 12/14 Pin CIRB12/14KPKF80 1,94/2,08 FT8/WA27F TH592 5 Yellow CIRIT12 CIRET12 - 12/14 Skt. CIRB12/14KSKF80 1,94/2,08 FT8/WA27F TH592 5 Yellow CIRIT12 CIRET12 CIRB12SG 12 Pin CIRB12KPKF80 2,50/3,00 FT8/WA27F TH592 7 Yellow CIRIT12 CIRET12 - 12 Skt. CIRB12KSKF80 2,50/3,00 FT8/WA27F TH592 7 Yellow CIRIT12 CIRET12 CIRB12SG LIF 12 Skt. CIRB12KLKF80 2,50/3,00 FT8/WA27F TH592 7 Yellow CIRIT12 CIRET12 CIRB12SG 12/10 Pin CIRB12/10KPKF80 5,53 M310 TH592 5 Yellow CIRIT12 CIRET12 - 12/10 Skt. CIRB12/10KSKF80 5,53 M310 TH592 5 Yellow CIRIT12 CIRET12 CIRB12SG 12/40 Pin CIRB12/40KPKF80 4,0 M310 TH592 5 Yellow CIRIT12 CIRET12 - 12/40 Skt. CIRB12/40KSKF80 4,0 M310 TH592 5 Yellow CIRIT12 CIRET12 CIRB12SG RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR F80 CONTACTS CRIMP & TOOLING DATA CONT. Contact Size & Type Contact Part Number Wire Size Tool C.S.A. Required mm2 Turret/ Locator Tool Setting Tool Pos’n If Applicable Insertion Tool Extraction Tool Guide Pins 8/40 Pin CIRB8/40KPKF80 4,0 D55E Die Set - - - - - 8/40 Skt. CIRB8/40KSKF80 4,0 D55E Die Set - - - - - 8/12 Pin CIRB8/12KPKF80 2,5 M310 Consult TE 3 - - - - 8/12 Skt. CIRB8/12KSKF80 2,5 M310 Consult TE 3 - - - - 8/10 Pin CIRB8/10KPKF80 5,53 D55E Die Set - - - - - 8/10 Skt. CIRB8/10KSKF80 5,53 D55E Die Set - - - - - 8 Pin CIRB8KPKF80 9,0 D36 Die Set 02541 - - - - - 8 Skt. CIRB8KSKF80 9,0 D36 Die Set 02541 - - - - - 100/60 Pin CIRB100/60KPKF80 6,0 D55E Die Set - - - - - 100/60 Skt. CIRB100/60KSKF80 6,0 D55E Die Set - - - - - 100 Pin CIRB100KPKF80 10,0 D55E Die Set MRP0925 - - - - - 100 Skt. CIRB100KSKF80 10,0 D55E Die Set MRP0925 - - - - - 4/10 Pin CIRB4/10KPKF80 5,53 D55E Die Set - - - - - 4/10 Skt. CIRB4/10KSKF80 5,53 D55E Die Set - - - - - 4 Pin CIRB4KPKF80 22,0 D36 Die Set - - - - - 4 Skt. CIRB4KSKF80 22,0 D36 Die Set - - - - - 160 Pin CIRB160KPKF80 16,0 D55E Die Set MRP0924 - - - - - 160 Skt. CIRB160KSKF80 16,0 D55E Die Set MRP0924 - - - - - 0 Pin CIRB0KPKF80 53,0 D36 Die Set - - - - - 0 Skt CIRB0KSKF80 53,0 D36 Die Set - - - - - 500/160 Pin CIRB500/160KPKF8 16,0 D55E Die Set MRP0924 - - - - - 500/160 Skt. CIRB500/160KSKF8 16,0 D55E Die Set MRP0924 - - - - - 500/250 Pin CIRB500/250KPKF8 25,0 D55E Die Set - - - - - 500/250 Skt. CIRB500/250KSKF8 25,0 D55E Die Set - - - - - 500/350 Pin CIRB500/350KPKF8 35,0 D55E Die Set - - - - - 500/350 Skt. CIRB500/350KSKF8 35,0 D55E Die Set - - - - - 500 Pin CIRB500KPKF80 50,0 D55E Die Set MRP0925 - - - - - 500 Skt. CIRB500KSKF80 50,0 D55E Die Set MRP0925 - - - - - PAGE 92 F80 COAX & TWINAX CONTACTS CRIMP & TOOLING DATA Contact Size & Type Contact Part Number Wire Size C.S.A. mm2 4 Coax Pin CIRB4CKPKF80P1001 0.5 4 Coax Skt 4 Coax Pin CIRB4CKSKF80P1001 0.5 CIRB4CKPKF80P1002 1.0 4 Coax Skt. CIRB4CKSKF80P1002 1.0 4 Twinax Pin CIRB4TKPKF80P1 0.5/0.6 4 Twinax Skt 4 Twinax Pin 4 Twinax Skt. CIRB4TKSKF80P1 CIRB4TKPKF80P1001 CIRB4TKSKF80P1001 Tool Number Supplier FT8 DMC WA27F DMC TH592 DMC HT250-3 DMC 67-012-01 DMC 67-016-01 DMC 68-012-01 DMC 68-016-01 DMC D51 Dubuis D55E Dubuis 0.5/0.6 0.75/1.0 0.75/1.0 RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR Contact Section Tool Required Turret/ Locator Tool Setting Tool Position If Applicable Inner FT8 TH619 4 Red Screen D55E/D51 31038 - - Inner FT8 TH619 4 Blue Screen D55E/D51 31038 - - Inner FT8 TH619 4 Red Screen D55E/D51 HD51-150 - - Inner FT8 TH619 4 Blue Screen D55E/D51 HD51-150 - - Inner FT8 TH608 4 Red Intermediate HX4 Y946 - - Screen D55E/D51 HD51-150 - - Inner FT8 TH608 4 Blue Intermediate HX4 Y946 - - Screen D55E/D51 HD51-150 - - Inner FT8 TH608 4 Red Intermediate HX4 Y946 - - Screen D55E/D51 HD51-150 - - Inner FT8 TH608 4 Blue Intermediate HX4 Y946 - - Screen D55E/D51 HD51-150 - - RFI BRAID SOCK, BANDIT STRAP & KNITMESH BRAID RFI Braid Sock TE Connectors Part Number Diameter Length Max Shell Size 22 CIRBMBS035015 ø 20 mm 100 mm CIRBMBS050015 ø 25 mm 150 mm 22 CIRBMBS020010 ø 35 mm 150 mm 32 CIRBMBS025015 ø 50 mm 150 mm 36 & 40 TE Connectors Part Number Length Width Max Shell Size CIRB600052 520 mm 6.1 mm 32 CIRB600090 900 mm 6.1 mm 36 & 40 CIRB608109 362 mm 4 mm 22 CIRB600057 07 mm 3 mm 22 Bandit Strap Bandit Tools TE Connectors Part Number Tool Description CIRB600058 Standard Bandit Tool CIRB600061 Micro Bandit Tool (3mm Band Straps) CIRB601200 Calibration Kit Knitmesh Braid TE Connectors Part Number Length Width CIRBMKM1050 500 mm 25 mm PAGE 94 For More Information Follow us on Twitter for all the latest product news @TEConnectivity, and on Facebook, TEConnectivity. TE Connectivity (TE) Technical Support Center North America +1 800 522 6752 Asia Pacific +86 0 400 820 6015 Austria +43 1 905 601 228 Baltic Regions +46 8 5072 5000 Benelux +31 73 6246 999 Czech Republic +420 800 701 462 France +33 1 34 20 86 86 Germany +49 6251 133 1999 Hungary +36 809 874 04 Italy +39 011 401 2632 Nordic +46 8 5072 5000 Poland +48 800 702 309 Russia +7495 790 790 2 Spain/Portugal +34 93 2910366 Switzerland +41 52 633 66 26 United Kingdom +44 800 267 666 te.com/Rail © 2016 TE Connectivity Ltd. family of companies. All Rights Reserved. 1-1773858-1 JS 0316 EVERY CONNECTION COUNTS, TE Connectivity, TE connectivity (logo) and TE are trademarks of the TE Connectivity group of companies andits licensors. SNCF, RATP, Alstom, Bombardier, LUL and other product or company names mentioned herein may be trademarks of their respective owners. While TE has made every reasonable effort to ensure the accuracy of the information herein, nothing herein constitutes any guarantee that such information is error-free, or any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. The TE entity issuing this publication reserves the right to make any adjustments to the information contained herein at any time without notice. All implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose are expressly disclaimed. The dimensions herein are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications. RAIL /// CIRH: MODULAR BAYONET LOCK CONNECTOR