CP2512-000

TITLE SPECIFICATION CONTROL DRAWING 82A6068 Date WIRE, RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE-INSULATED, NORMAL WEIGHT, GENERAL PURPOSE, 1000 VOLT Revision 12-4-12 C This specification sheet forms a part of the latest issue of Raychem Specification 80. PRIMARY INSULATION - RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE COLOR - LIGHT GREEN CONDUCTOR - SILVER-COATED COPPER JACKET - RADIATION-CROSSLINKED, MODIFIED FLEXIBLE ETFE TABLE I. CONSTRUCTION DETAILS DIAMETER OF STRANDED CONDUCTOR (in.) FINISHED WIRE PART NUMBER 1/ WIRE SIZE (AWG) CONDUCTOR STRANDING (number x AWG) MINIMUM MAXIMUM 82A6068-16-* 16 259 x 40 .061 .067 82A6068-12-* 12 665 x 40 .096 82A6068-10-* 10 665 x 38 .126 82A6068-8-* 8 665 x 36 .157 .173 .714 .249 ± .008 82A6068-6-* 6 1045 x 36 .192 .208 .490 .284 ± .010 121. 82A6068-4-* 4 1665 x 36 .265 .285 .326 .359 ± .010 190. MAXIMUM RESISTANCE AT 20°C (ohms/1000 ft.) DIAMETER (in.) MAXIMUM WEIGHT (lbs/1000 ft.) 4.62 .148 ± .008 22.0 .106 1.89 .185 ± .008 39.6 .140 1.12 .217 ± .008 59.1 84.1 TABLE II. PERFORMANCE DETAILS BEND TESTING PART NUMBER 1/ MANDREL DIAMETER (inch) (± 3%) WEIGHT (lb) (± 3%) CROSSLINKING PROOF TEST CROSSLINKING PROOF TEST 82A6068-16-* 1.50 3.00 82A6068-12-* 2.00 3.00 82A6068-10-* 3.00 4.00 82A6068-8-* 3.00 4.00 82A6068-6-* 4.00 4.00 82A6068-4-* 5.00 4.00 Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 2 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2008-2012 Tyco Electronics Corporation,. All rights reserved. Revision SPECIFICATION CONTROL DRAWING Page 2 of 2 C WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 1000 volts (rms) at 150°C and 15,000 ft. (maximum) CONCENTRICITY: 70% (minimum) CROSSLINKING PROOF TEST: AWG 16: 300 ± 3°C for 30 minutes AWG 12-4: 300 ± 3°C for 1 hour IDENTIFICATION AND COLOR STRIPING DURABILITY: 125 cycles (250 strokes) (minimum), 500 g weight INSULATION ELONGATION AND TENSILE STRENGTH: AWG 16-10: Elongation, 75% (minimum) Tensile Strength, 3500 lbf/in² (minimum) AWG 8-4: Elongation, 125% (minimum) Tensile Strength, 3000 lbf/in² (minimum) INSULATION FLAWS: Primary Insulation, Spark Test, 1.5 kV (rms) at 3 kHz Impulse Dielectric Test, 6.0 kV (peak) Finished Wire, Spark Test, 3.0 kV (rms) at 3 kHz Impulse Dielectric Test, 8.0 kV (peak) INSULATION THICKNESS: .010 in. (minimum) for primary insulation .012 in. (minimum) for outer jacket JACKET COLOR: White preferred PRODUCT IDENTIFICATION: AWG 16-10, black ink only AWG 8-4, black ink preferred SECANT MODULUS: (Test per ASTM D 882) AWG 16-10: 5.0 x 104 lbf/in2 (maximum) AWG 8 and larger: 4.0 x 104 lbf/in2 (maximum) 2% strain, 2 inch jaw separation, 0.2 inch/minute SHRINKAGE: 200 ± 3°C for 6 hours, AWG 16-10: 0.13 in. (maximum) in 12 inches AWG 8-4: 0.25 in. (maximum) in 12 inches VOLTAGE WITHSTAND (Post Environmental): 2500 volts (rms), 60 Hz PART NUMBER: The “*” in the part numbers on page 1 shall be replaced by a color code designator. 1/ Example: AWG 12, white; 82A6068-12-9 AWG 12, white with a black stripe; 82A6068-12-90 1/ See footer section on page 1 SCD Number 82A6068