CWT-3-W122-5

CUSTOMER DRAWING Product Description CWT-3-W122-5 CWT-5-W122-5 CWT-6-W122-5 CWT-7-W122-5 CWT-9-W122-5 CWT-11-W122-5 CWT-13-W122-5 Product Dimensions øA øB L MIN MIN MAX 2.50 3.00 24.50 (0.098) (0.118) (0.965) 4.30 4.80 29.30 (0.169) (0.189) (1.154) 6.00 6.70 32.00 (0.236) (0.264) (1.260) 6.40 7.30 32.50 (0.252) (0.287) (1.280) 8.70 9.20 35.50 (0.343) (0.362) (1.398) 10.00 11.50 35.50 (0.394) (0.453) (1.398) 13.00 15.00 45.50 (0.512) (0.591) (1.791) øD MAX 3.00 (0.118) 4.80 (0.189) 6.70 (0.264) 7.30 (0.287) 9.20 (0.362) 11.50 (0.453) 15.10 (0.594) øE MIN 1.50 (0.059) 2.00 (0.079) 3.30 (0.130) 3.30 (0.130) 4.50 (0.177) 4.50 (0.177) 7.00 (0.276) Cable Dimensions øF øG MIN MAX 1.00 2.50 (0.040) (0.098) 1.50 4.30 (0.059) (0.169) 2.80 6.00 (0.110) (0.236) 2.80 6.40 (0.110) (0.252) 4.00 8.70 (0.157) (0.343) 4.00 10.00 (0.157) (0.394) 6.50 13.00 (0.256) (0.512) J 7.00±0.50 (0.276±0.020) 9.00±0.50 (0.354±0.020) 10.00± 0.50 (0.394±0.020) 11.00±1.00 (0.433±0.040) 12.00± 1.00 (0.472±0.040) 13.00±1.00 (0.512±0.040) 17.00±1.00 (0.669±0.040) MATERIALS 1. INSULATION SLEEVE: Transparent heat-shrinkable radiation cross-linked modified polyolefin. 2. SOLDER PREFORM WITH FLUX: SOLDER: TYPE Cd18 per ANSI/J-STD-006. FLUX: TYPE ROM1 per ANSI/J-STD-004. 3. MELTABLE SEALING RING: Thermally stabilized thermoplastic. 4. GROUND LEAD: Raychem cross-linked polyethylene wire, AWG22, stranded tin plated copper. Color: green. APPLICATION 1. These controlled soldering devices are designed for termination of a bare or tin-plated copper shield on a cable having an insulation rated for at least +85qC, meeting the dimensional criteria listed in the table above. 2. Temperature range: -55qC to +125qC. 3. When installed properly, these devices will meet the requirements of TE Connectivity/Raychem Specification RT-1404. 4. For installation procedure and application equipment, consult TE Connectivity /Raychem RPIP 824-00. For best results, prepare the cable as shown: TITLE: SOLDERSLEEVE TERMINATOR WITH PRE-INSTALLED LEAD Unless otherwise specified dimensions are in millimeters.[Inches dimensions are shown in brackets] Raychem DIMENSIONING AND TOLERANCING PER GPS Devices (ISO STANDARDS) ANGLES: ± 0°30’ Tyco Electronics Corporation reserves TOLERANCES: the right to amend this drawing at any ROUGHNESS 0.00 ± 0.02 MM time. Users should evaluate the 0.0 ± 0.2 MM IN MICRON suitability of the product for their 0 ± 0.5 MM application. PREPARED BY: CAGE CODE: ECO NUMBER: DOCUMENT NO.: YNGUYEN 06090 ECO-12-008844 © 2003-2012 Tyco Electronics Corporation. All rights reserved. NTS CWT-XX-W122-5 REV: DATE: C SCALE: If this document is printed it becomes uncontrolled. Check for the latest revision. May 9, 2012 SIZE: A SHEET: 1 of 1